| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, 32-bit: Align percpu area and irq stacks to THREAD_SIZE
x86: Move alloc_desk_mask variables inside ifdef
x86-32: Align IRQ stacks properly
x86: Remove CONFIG_4KSTACKS
x86: Always use irq stacks
Fixed up trivial conflicts in include/linux/{irq.h, percpu-defs.h}
|
|
IRQ stacks provide much better safety against unexpected stack use from
interrupts, at the minimal downside of slightly higher memory usage.
Enable irq stacks also for the default 8k stack on 32-bit kernels to
minimize the problem of stack overflows through interrupt activity.
This is what the 64-bit kernel and various other architectures already do.
Signed-off-by: Christoph Hellwig <hch@lst.de>
LKML-Reference: <20100628121554.GA6605@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add support for saving OFW's cif, and later calling into it to run OFW
commands. OFW remains resident in memory, living within virtual range
0xff800000 - 0xffc00000. A single page directory entry points to the
pgdir that OFW actually uses, so rather than saving the entire page
table, we grab and install that one entry permanently in the kernel's
page table.
This is currently only used by the OLPC XO. Note that this particular
calling convention breaks PAE and PAT, and so cannot be used on newer
x86 hardware.
Signed-off-by: Andres Salomon <dilinger@queued.net>
LKML-Reference: <20100618174653.7755a39a@dev.queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Now that numa=fake=<size>[MG] is implemented, it is possible to remove
configurable node size support. The command-line parsing was already
broken (numa=fake=*128, for example, would not work) and since fake nodes
are now interleaved over physical nodes, this support is no longer
required.
Signed-off-by: David Rientjes <rientjes@google.com>
LKML-Reference: <alpine.DEB.2.00.1002151343080.26927@chino.kir.corp.google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
numa=fake=N specifies the number of fake nodes, N, to partition the
system into and then allocates them by interleaving over physical nodes.
This requires knowledge of the system capacity when attempting to
allocate nodes of a certain size: either very large nodes to benchmark
scalability of code that operates on individual nodes, or very small
nodes to find bugs in the VM.
This patch introduces numa=fake=<size>[MG] so it is possible to specify
the size of each node to allocate. When used, nodes of the size
specified will be allocated and interleaved over the set of physical
nodes.
FAKE_NODE_MIN_SIZE was also moved to the more-appropriate
include/asm/numa_64.h.
Signed-off-by: David Rientjes <rientjes@google.com>
LKML-Reference: <alpine.DEB.2.00.1002151342510.26927@chino.kir.corp.google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Add missing information about requirements of using the EHCI usb debug
controller as well as to mention you can use a debug controller other
than the first one in the system.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@intel.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
x86: Move get/set_wallclock to x86_platform_ops
x86: platform: Fix section annotations
x86: apic namespace cleanup
x86: Distangle ioapic and i8259
x86: Add Moorestown early detection
x86: Add hardware_subarch ID for Moorestown
x86: Add early platform detection
x86: Move tsc_init to late_time_init
x86: Move tsc_calibration to x86_init_ops
x86: Replace the now identical time_32/64.c by time.c
x86: time_32/64.c unify profile_pc
x86: Move calibrate_cpu to tsc.c
x86: Make timer setup and global variables the same in time_32/64.c
x86: Remove mca bus ifdef from timer interrupt
x86: Simplify timer_ack magic in time_32.c
x86: Prepare unification of time_32/64.c
x86: Remove do_timer hook
x86: Add timer_init to x86_init_ops
x86: Move percpu clockevents setup to x86_init_ops
x86: Move xen_post_allocator_init into xen_pagetable_setup_done
...
Fix up conflicts in arch/x86/include/asm/io_apic.h
|
|
x86 bootprotocol 2.07 has introduced hardware_subarch ID in the boot
parameters provided by FW. We use it to identify Moorestown platforms.
[ tglx: Cleanup and paravirt fix ]
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch adds kernel configuration and boot support for Intel Trusted
Execution Technology (Intel TXT).
Intel's technology for safer computing, Intel Trusted Execution
Technology (Intel TXT), defines platform-level enhancements that
provide the building blocks for creating trusted platforms.
Intel TXT was formerly known by the code name LaGrande Technology (LT).
Intel TXT in Brief:
o Provides dynamic root of trust for measurement (DRTM)
o Data protection in case of improper shutdown
o Measurement and verification of launched environment
Intel TXT is part of the vPro(TM) brand and is also available some
non-vPro systems. It is currently available on desktop systems based on
the Q35, X38, Q45, and Q43 Express chipsets (e.g. Dell Optiplex 755, HP
dc7800, etc.) and mobile systems based on the GM45, PM45, and GS45
Express chipsets.
For more information, see http://www.intel.com/technology/security/.
This site also has a link to the Intel TXT MLE Developers Manual, which
has been updated for the new released platforms.
A much more complete description of how these patches support TXT, how to
configure a system for it, etc. is in the Documentation/intel_txt.txt file
in this patch.
This patch provides the TXT support routines for complete functionality,
documentation for TXT support and for the changes to the boot_params structure,
and boot detection of a TXT launch. Attempts to shutdown (reboot, Sx) the system
will result in platform resets; subsequent patches will support these shutdown modes
properly.
Documentation/intel_txt.txt | 210 +++++++++++++++++++++
Documentation/x86/zero-page.txt | 1
arch/x86/include/asm/bootparam.h | 3
arch/x86/include/asm/fixmap.h | 3
arch/x86/include/asm/tboot.h | 197 ++++++++++++++++++++
arch/x86/kernel/Makefile | 1
arch/x86/kernel/setup.c | 4
arch/x86/kernel/tboot.c | 379 +++++++++++++++++++++++++++++++++++++++
security/Kconfig | 30 +++
9 files changed, 827 insertions(+), 1 deletion(-)
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
exception.txt only explains the code on x86, so it's better to
move it into Documentation/x86 directory.
And also rename it to exception-tables.txt which looks much
more reasonable.
This patch is on top of the previous one.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
arch/x86/kernel/cpu/mcheck/mce_64.c
arch/x86/kernel/irq.c
Merge reason: Resolve the conflicts above.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch introduces three boot options (no_cmci, dont_log_ce
and ignore_ce) to control handling for corrected errors.
The "mce=no_cmci" boot option disables the CMCI feature.
Since CMCI is a new feature so having boot controls to disable
it will be a help if the hardware is misbehaving.
The "mce=dont_log_ce" boot option disables logging for corrected
errors. All reported corrected errors will be cleared silently.
This option will be useful if you never care about corrected
errors.
The "mce=ignore_ce" boot option disables features for corrected
errors, i.e. polling timer and cmci. All corrected events are
not cleared and kept in bank MSRs.
Usually this disablement is not recommended, however it will be
a help if there are some conflict with the BIOS or hardware
monitoring applications etc., that clears corrected events in
banks instead of OS.
[ And trivial cleanup (space -> tab) for doc is included. ]
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <4A30ACDF.5030408@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: fix system without memory on node0
x86, mm: Fix node_possible_map logic
mm, x86: remove MEMORY_HOTPLUG_RESERVE related code
x86: make sparse mem work in non-NUMA mode
x86: process.c, remove useless headers
x86: merge process.c a bit
x86: use sparse_memory_present_with_active_regions() on UMA
x86: unify 64-bit UMA and NUMA paging_init()
x86: Allow 1MB of slack between the e820 map and SRAT, not 4GB
x86: Sanity check the e820 against the SRAT table using e820 map only
x86: clean up and and print out initial max_pfn_mapped
x86/pci: remove rounding quirk from e820_setup_gap()
x86, e820, pci: reserve extra free space near end of RAM
x86: fix typo in address space documentation
x86: 46 bit physical address support on 64 bits
x86, mm: fault.c, use printk_once() in is_errata93()
x86: move per-cpu mmu_gathers to mm/init.c
x86: move max_pfn_mapped and max_low_pfn_mapped to setup.c
x86: unify noexec handling
x86: remove (null) in /sys kernel_page_tables
...
|
|
On Intel platforms machine check exceptions are always broadcast to
all CPUs. This patch makes the machine check handler synchronize all
these machine checks, elect a Monarch to handle the event and collect
the worst event from all CPUs and then process it first.
This has some advantages:
- When there is a truly data corrupting error the system panics as
quickly as possible. This improves containment of corrupted
data and makes sure the corrupted data never hits stable storage.
- The panics are synchronized and do not reenter the panic code
on multiple CPUs (which currently does not handle this well).
- All the errors are reported. Currently it often happens that
another CPU happens to do the panic first, but reports useless
information (empty machine check) because the real error
happened on another CPU which came in later.
This is a big advantage on Nehalem where the 8 threads per CPU
lead to often the wrong CPU winning the race and dumping
useless information on a machine check. The problem also occurs
in a less severe form on older CPUs.
- The system can detect when no CPUs detected a machine check
and shut down the system. This can happen when one CPU is so
badly hung that that it cannot process a machine check anymore
or when some external agent wants to stop the system by
asserting the machine check pin. This follows Intel hardware
recommendations.
- This matches the recommended error model by the CPU designers.
- The events can be output in true severity order
- When a panic happens on another CPU it makes sure to be actually
be able to process the stop IPI by enabling interrupts.
The code is extremly careful to handle timeouts while waiting
for other CPUs. It can't rely on the normal timing mechanisms
(jiffies, ktime_get) because of its asynchronous/lockless nature,
so it uses own timeouts using ndelay() and a "SPINUNIT"
The timeout is configurable. By default it waits for upto one
second for the other CPUs. This can be also disabled.
From some informal testing AMD systems do not see to broadcast
machine checks, so right now it's always disabled by default on
non Intel CPUs or also on very old Intel systems.
Includes fixes from Ying Huang
Fixed a "ecception" in a comment (H.Seto)
Moved global_nwo reset later based on suggestion from H.Seto
v2: Avoid duplicate messages
[ Impact: feature, fixes long standing problems. ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Document that check_interval set to 0 means no polling.
Noticed by Hidetoshi Seto
Also add a reference from boot options to the sysfs tunables
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
after:
| commit b263295dbffd33b0fbff670720fa178c30e3392a
| Author: Christoph Lameter <clameter@sgi.com>
| Date: Wed Jan 30 13:30:47 2008 +0100
|
| x86: 64-bit, make sparsemem vmemmap the only memory model
we don't have MEMORY_HOTPLUG_RESERVE anymore.
Historically, x86-64 had an architecture-specific method for memory hotplug
whereby it scanned the SRAT for physical memory ranges that could be
potentially used for memory hot-add later. By reserving those ranges
without physical memory, the memmap would be allocated and left dormant
until needed. This depended on the DISCONTIG memory model which has been
removed so the code implementing HOTPLUG_RESERVE is now dead.
This patch removes the dead code used by MEMORY_HOTPLUG_RESERVE.
(Changelog authored by Mel.)
v2: updated changelog, and remove hotadd= in doc
[ Impact: remove dead code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Mel Gorman <mel@csn.ul.ie>
Workflow-found-OK-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A0C4910.7090508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Document the new bzImage fields for kernel memory placement.
[ Impact: adds documentation ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Fix a trivial typo in Documentation/x86/x86_64/mm.txt.
[ Impact: documentation only ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Rik van Riel <riel@redhat.com>
|
|
Extend the maximum addressable memory on x86-64 from 2^44 to
2^46 bytes. This requires some shuffling around of the vmalloc
and virtual memmap memory areas, to keep them away from the
direct mapping of up to 64TB of physical memory.
This patch also introduces a guard hole between the vmalloc
area and the virtual memory map space. There's really no
good reason why we wouldn't have a guard hole there.
[ Impact: future hardware enablement ]
Signed-off-by: Rik van Riel <riel@redhat.com>
LKML-Reference: <20090505172856.6820db22@cuia.bos.redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
|
|
cgroup documentation was moved to Documentation/cgroups/. There are some
places that still refer to Documentation/controllers/,
Documentation/cgroups.txt and Documentation/cpusets.txt. Fix those.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
[ mingo: small edits and extensions. ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Greg KH <gregkh@suse.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <49AF18B7.4050305@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
'x86/setup-lzma', 'x86/signal' and 'x86/urgent' into x86/core
|
|
Modify field names to the right ones:
- start_sys was changed to start_sys_seg
- iinitrd_addr_max was changed to ramdisk_max
- pad2 was changed to pad2 and pad3
- readmode_swtch was changed to realmode_swtch
Signed-off-by: Baodong Chen <[email]chenbdchenbd@gmail.com[email]>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: documentation
Update the boot protocol specification to include the currently
supported file formats and their magic numbers.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86: fix section mismatch warnings in mcheck/mce_amd_64.c
x86: offer frame pointers in all build modes
x86: remove duplicated #include's
x86: k8 numa register active regions later
x86: update Alan Cox's email addresses
x86: rename all fields of mpc_table mpc_X to X
x86: rename all fields of mpc_oemtable oem_X to X
x86: rename all fields of mpc_bus mpc_X to X
x86: rename all fields of mpc_cpu mpc_X to X
x86: rename all fields of mpc_intsrc mpc_X to X
x86: rename all fields of mpc_lintsrc mpc_X to X
x86: rename all fields of mpc_iopic mpc_X to X
x86: irqinit_64.c init_ISA_irqs should be static
Documentation/x86/boot.txt: payload length was changed to payload_length
x86: setup_percpu.c fix style problems
x86: irqinit_64.c fix style problems
x86: irqinit_32.c fix style problems
x86: i8259.c fix style problems
x86: irq_32.c fix style problems
x86: ioport.c fix style problems
...
|
|
Update several Documentation/ files and a few sub-dir files (only one
change in each) to reflect changed header files locations.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Baodong Chen <[email]chenbdchenbd@gmail.com[email]>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
'x86/crashdump', 'x86/debug', 'x86/defconfig', 'x86/detect-hyper', 'x86/doc', 'x86/dumpstack', 'x86/early-printk', 'x86/fpu', 'x86/idle', 'x86/io', 'x86/memory-corruption-check', 'x86/microcode', 'x86/mm', 'x86/mtrr', 'x86/nmi-watchdog', 'x86/pat2', 'x86/pci-ioapic-boot-irq-quirks', 'x86/ptrace', 'x86/quirks', 'x86/reboot', 'x86/setup-memory', 'x86/signal', 'x86/sparse-fixes', 'x86/time', 'x86/uv' and 'x86/xen' into x86/core
|
|
Impact: Documentation only.
Documentation updates as per Randy Dunlap's comments.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
- v3
Impact: Documentation only.
Add documentation related to pgprot_* change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: clarify documentation
Documentation/x86/boot.txt describes payload_offset as the offset
from the end of the real-mode code. In fact, it is more accurately
described as the offset from the beginning of the protected-mode
code, as (a) this is how it is actually calculated and (b) the padding
after the real-mode code is not included in the offset.
Signed-off-by: Philipp Kohlbecher <xt28@gmx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
Impact: documentation fix
I met okuji-san (GRUB maintainer) yesterday.
He said GRuB isn't correct spelled and he want to fix it.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: documentation update
Commit a6523748bddd38bcec11431f57502090b6014a96
(paravirt/x86, 64-bit: move __PAGE_OFFSET to leave a space for hypervisor)
changed address space without changing the documentation.
Change it according to the code change -- direct mapping start:
ffff810000000000 => ffff880000000000 which gives 57 TiB, something
between 45 and 46 bits.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: documentation update
1) nmi_watchdog boot parameter is common to 32/64 bit modes. So
move it from Documentation/x86/x86_64/boot-options.txt to
Documentation/kernel-parameters.txt and integrate with.
2) Also fix [panic] keyword placement -- it ought to be at first
position otherwise it will not be recognized.
3) Document lapic and ioapic keywords.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The Documentation/i386 and Documentation/x86_64 directories and their
contents have been moved into Documentation/x86. Fix references to
those files accordingly.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Commit ecd29476ae0143b1c3641edfa76c0fc3e9ad3021 removed the
"disable_8254_timer" and "enable_8254_timer" kernel parameters from
the kernel but did not remove the references to them from two
files in the Documentation directory: kernel-parameters.txt and
x86/x86_64/boot-options.txt.
This change completes the removal.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Documentation update for PAT. Reflect the latest API details.
Also, adds details about ways to get more info in order to debug PAT.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Move mtrr.txt to the Documentation/x86/ subdirectory.
Add 00-INDEX to the Documentation/x86/ subdirectory.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The start_sys field is two bytes, not four.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
The boot protocol, USB legacy support, and zero-page documentation is
common to the x86 platform, not i386-specific.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Applies on top of the previous patch:
x86 boot: add code to add BIOS provided EFI memory entries to kernel
Instead of always adding EFI memory map entries (if present) to the
memory map after initially finding either E820 BIOS memory map entries
and/or kernel command line memmap entries, -instead- only add such
additional EFI memory map entries if the kernel boot option:
add_efi_memmap
is specified.
Requiring this 'add_efi_memmap' option is backward compatible with
kernels that didn't load such additional EFI memory map entries in
the first place, and it doesn't override a configuration that tries
to replace all E820 or EFI BIOS memory map entries with ones given
entirely on the kernel command line.
Signed-off-by: Paul Jackson <pj@sgi.com>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Cc: "Jack Steiner" <steiner@sgi.com>
Cc: "Mike Travis" <travis@sgi.com>
Cc: "Huang
Cc: Ying" <ying.huang@intel.com>
Cc: "Andi Kleen" <andi@firstfloor.org>
Cc: "Andrew Morton" <akpm@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
The current organization of the x86 documentation makes it appear as
if the "i386" documentation doesn't apply to x86-64, which is does.
Thus, move that documentation into Documentation/x86, and move the
x86-64-specific stuff into Documentation/x86/x86_64 with the eventual
goal to move stuff that isn't actually 64-bit specific back into
Documentation/x86.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Documentation about PAT related interfaces, intended usage and memory attribute
relationship.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
