Age | Commit message (Collapse) | Author |
|
Device-tree bindings for TI DA850/OMAP-L138/AM18XX pullup/pulldown
pinconf controller.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
definition
GPIO7 is configured in POWERHOLD mode which has higher priority
over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON
bit is turned off. This property enables driver to over ride the
POWERHOLD value to GPIO7 so as to turn off the PMIC in power off
scenarios.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
A new clock controller for the rk1108 soc (single-core Cortex-A7+DSP),
a fix making sure the cpuclk rate is actually valid, before trying to
set it and a copy-paste fix for the rk3399's testclk.
* tag 'v4.10-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: add clock controller for rk1108
dt-bindings: add documentation for rk1108 cru
clk: rockchip: add dt-binding header for rk1108
clk: rockchip: fix copy-paste error in rk3399 testclk
clk: rockchip: validity should be checked prior to cpu clock rate change
|
|
Re-using idle state definition provided by arm,idle-state for domain
idle states creates a lot of confusion and limits further evolution of
the domain idle definition. To keep things clear and simple, define a
idle states for domain using a new compatible "domain-idle-state".
Fix existing PM domains code to look for the newly defined compatible.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This adds support for the AU Optronics G185HAN01 18.5" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This adds support for the AU Optronics G133HAN01 13.3" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Chunghwa CLAA070WP03XG is a 7" 1280x800 panel, which can be
supported by the simple panel driver.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add three reset control signals, "mac_core_rst", "mac_ifc_rst" and
"phy_rst".
The following diagram explained how the reset signals work.
SoC
|-----------------------------------------------------
| ------ |
| | cpu | |
| ------ |
| | |
| ------------ AMBA bus |
| GMAC | |
| ---------------------- |
| ------------- mac_core_rst | -------------- | |
| |clock and |-------------->| mac core | | |
| |reset | | -------------- | |
| |generator |---- | | | |
| ------------- | | ---------------- | |
| | ---------->| mac interface | | |
| | mac_ifc_rst | ---------------- | |
| | | | | |
| | | ------------------ | |
| |phy_rst | | RGMII interface | | |
| | | ------------------ | |
| | ---------------------- |
|----------|------------------------------------------|
| |
| ----------
|--------------------- |PHY chip |
----------
The "mac_core_rst" represents "mac core reset signal", it resets
the mac core including packet processing unit, descriptor processing unit,
tx engine, rx engine, control unit.
The "mac_ifc_rst" represents "mac interface reset signal", it resets
the mac interface. The mac interface unit connects mac core and
data interface like MII/RMII/RGMII. After we set a new value of
interface mode, we must reset mac interface to reload the new mode value.
The "mac_core_rst" and "mac_ifc_rst" are both optional to be
backward compatible with the hix5hd2 SoC.
The "phy_rst" represents "phy reset signal", it does a hardware reset
on the PHY chip. This reset signal is optional if the PHY can work well
without the hardware reset.
Add one more clock signal, the existing is MAC core clock,
and the new one is MAC interface clock.
The MAC interface clock is optional to be backward compatible with
the hix5hd2 SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "hix5hd2" is SoC name, add the generic ethernet driver name.
The "hisi-gemac-v1" is the basic version and "hisi-gemac-v2" adds
the SG/TXCSUM/TSO/UFO features.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add new DT bindings for new MXSFB driver that is using the
OF graph to parse the video output structure instead of
hard-coding the display properties into the MXSFB node.
The old MXSFB fbdev driver bindings are preserved in the
same file in the "Old bindings" section.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Clean up the ad-hoc indentation in the documentation, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
|
|
On certain platforms (like TI), DVFS for a single device (CPU) requires
configuring multiple power supplies.
The OPP bindings already contains binding and example to explain this
case, but it isn't sufficient.
- There is no way for the code parsing these bindings to know which
voltage values belong to which power supply.
- It is not possible to know the order in which the supplies need to be
configured while switching OPPs.
This patch clarifies on those details by mentioning that such
information is left for the implementation specific bindings to explain.
They may want to hardcode such details or implement their own properties
to get such information. All implementations using multiple regulators
for their devices must provide a binding document explaining their
implementation.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The regulator bindings allow the "<name>-supply" property to define a
single parent supply and not a list of parents.
Fix the wrong example code present in OPP bindings.
While at it also change the compatible string as Rob pointed out earlier
that none of A7 implementation have multiple supplies for the CPU core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Linux 4.9-rc8
Daniel requested this so we could apply some follow on fixes cleanly to -next.
|
|
The label property can be used to specify a name of the edge, for
consistent naming purposes.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
MYIR Tech Limited offers a range of ARM powered development boards and SoMs,
for details reference a list on http://elinux.org/Development_Platforms#ARM
or company's website http://myirtech.com
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-12-01
this is a pull request of 4 patches for net-next/master.
There are two patches by Chris Paterson for the rcar_can and rcar_canfd
device tree binding documentation. And a patch by Geert Uytterhoeven
that corrects the order of interrupt specifiers.
The fourth patch by Colin Ian King fixes a spelling error in the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document the devicetree bindings for the Microchip MCP3021/3221.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the tc654 and tc655 fan controllers from Microchip.
http://ww1.microchip.com/downloads/en/DeviceDoc/20001734C.pdf
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed continuation line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Armada 3700 is a new ARMv8 SoC from Marvell using same network controller
as older Armada 370/38x/XP. There are however some differences that
needed taking into account when adding support for it:
* open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus
configuration for network controller has to be done on two levels:
global and per-port. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed
* make per-CPU operation optional - Recent patches adding RSS and XPS
support for Armada 38x/XP enabled per-CPU operation of the controller
by default. Contrary to older SoC's Armada 3700 SoC's network
controller is not capable of per-CPU processing due to interrupt lines'
connectivity. This patch restores non-per-CPU operation, which is now
optional and depends on neta_armada3700 flag value in mvneta_port
structure. In order not to complicate the code, separate interrupt
subroutine is implemented.
For now, on the Armada 3700, RSS is disabled as the current
implementation depend on the per cpu interrupts.
[gregory.clement@free-electrons.com: extract from a larger patch, replace
some ifdef and port to net-next for v4.10]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a binding document for lpi2c driver.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This commit documents the compatible string to have the compatibility for
the I2C unit found in the Armada 3700.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds DT binding documentation for Exnos5433 based TM2
and TM2E boards sound subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BUCK regulators 3, 4, and 5 also have a 10mV step mode,
adjust the tables and logic to reflect the data-sheet for
these regulators.
fixes: d2a2e729a666 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to both DTS (example and actual files), and Linux driver code,
the first interrupt specifier should be the Channel interrupt, while the
second interrupt specifier should be the Global interrupt.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
tilcdc changes for v4.10
* tag 'tilcdc-4.10' of https://github.com/jsarha/linux: (23 commits)
drm/tilcdc: fix parsing of some DT properties
drm/tilcdc: Enable frame done irq and functionality for LCDC rev 1
drm/tilcdc: Configure video mode to HW in enable() not in mode_set_nofb()
drm/tilcdc: Load palette at the end of mode_set_nofb()
drm/tilcdc: Add timeout wait for palette loading to complete
drm/tilcdc: Enable palette loading for revision 2 LCDC too
drm/tilcdc: Fix load mode bit-field setting in tilcdc_crtc_enable()
drm/tilcdc: Add tilcdc_write_mask() to tilcdc_regs.h
drm/tilcdc: Fix tilcdc_crtc_create() return value handling
drm/tilcdc: implement palette loading for rev1
drm/tilcdc: Enable sync lost error and recovery handling for rev 1 LCDC
drm/tilcdc: Add drm bridge support for attaching drm bridge drivers
drm/bridge: Add ti-tfp410 DVI transmitter driver
dt-bindings: Move "ti,tfp410.txt" from display/ti to display/bridge
drm/tilcdc: Recover from sync lost error flood by resetting the LCDC
drm/tilcdc: Fix race from forced shutdown of crtc in unload
drm/tilcdc: Use unload to handle initialization failures
drm/tilcdc: Stop using struct drm_driver load() callback
drm/tilcdc: Remove obsolete drm_connector_register() calls
drm/tilcdc: Correct misspelling in error message
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "omap dts changes for v4.10, part 2" from Tony Lindgren:
Second set of device tree changes for omaps for v4.10 merge window:
- Fix up new instances of gpio-key,wakeup to use wakeup-source
- Add beaglebone LCDC blue-and-red-wiring property to make use
of the new driver features
- Add bindings for IIO support for am335x and am437x
- Add palmas PMIC overide powerhold property for am57xx
- Update am335x-baltos to use phy-handle property
- Add initial support for am571x-idk
* tag 'omap-for-v4.10/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: AM571x-IDK Initial Support
ARM: dts: am335x-baltos: use phy-phandle declarations
ARM: dts: am57xx-idk-common: Add overide powerhold property
ARM: dts: am57xx-beagle-x15-common: Add overide powerhold property
ARM: dts: am57xx-idk: Add Industrial output support
ARM: dts: am57xx-idk: Add Industrial input support
ARM: dts: am437x-idk: Add Industrial output support
ARM: dts: am437x-idk: Add Industrial input support
ARM: dts: am335x-icev2: Add ADC support
ARM: dts: am335x-icev2: Disable Industrial I/O LEDs and fix naming
ARM: dts: am335x-icev2: Add Industrial input support
ARM: dts: am335x-boneblack: Add blue-and-red-wiring -property to LCDC node
ARM: dts: omap5: replace gpio-key,wakeup with wakeup-source property
|
|
Pull "mvebu dt for 4.10 (part 1)" from Gregory CLEMENT:
Add Turris Omnia support, an open hardware router Armada 385 based
* tag 'mvebu-dt-4.10-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.10" from Heiko Stübner:
A bit of attention for the rk3066, fixed tsadc reset node
as well as enabling the dma for uart and mmc controllers.
And one new soc, the rk1108 combining a single-core Cortex-A7
with a separate DSP core.
* tag 'v4.10-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the sdmmc pinctrl for rk1108
ARM: dts: rockchip: add rockchip RK1108 Evaluation board
ARM: dts: rockchip: add basic support for RK1108 SOC
clk: rockchip: add dt-binding header for rk1108
dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description
ARM: dts: rockchip: enable dma for uart and mmc on rk3066a
ARM: dts: rockchip: fix TSADC reset node for rk3066a
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt64
Pull "Amlogic 64-bit DT updates for v4.10, round 2" from Kevin Hilman:
- new SoC support: S912/GXM series (8x A53)
- new boards: Nexbox A1 (S912), Nexbox A95X (S905X)
- resets for 2nd USB PHY
- update SCPI compatible for pre-v1.0 devices
* tag 'amlogic-dt64-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM64: dts: Add support for Meson GXM
ARM64: dts: meson-gxbb: add the USB reset also to the second USB PHY
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "Rockchip dts64 changes for 4.10" from Heiko Stübner:
Some more powerdomains and usb2-otg support for the rk3399 as well
as the binding doc for the 32bit rk1108 eval board to prevent it
from conflicting with the recently added 64bit px5 board.
* tag 'v4.10-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: rockchip: add usb2-phy otg-port support for rk3399
arm64: dts: rockchip: add pd_sd power-domain node for rk3399
arm64: dts: rockchip: add eMMC's power domain support for rk3399
arm64: dts: rockchip: add backlight support for rk3399 evb board
arm64: dts: rockchip: add gmac needed pclk for rk3399 pd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers
Pull "Qualcomm ARM Based Driver Updates for v4.10 - Part 2" from Andy Gross:
* Fixup QCOM SCM to support MSM8996
* tag 'qcom-drivers-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
|
|
Till now we used clockevent from generic ARC driver.
This was enough as long as we worked with simple multicore SoC.
When we are working with multithread SoC each HW thread can be
scheduled to receive timer interrupt using timer mask register.
This patch will provide a way to control clock events per HW thread.
The design idea is that for each core there is dedicated register
(TSI) serving all 16 HW threads.
The register is a bitmask with one bit for each HW thread.
When HW thread wants that next expiration of timer interrupt will
hit it then the proper bit should be set in this dedicated register.
When timer expires all HW threads within this core which their bit
is set at the TSI register will be interrupted.
Driver can be used from device tree by:
compatible = "ezchip,nps400-timer0" <-- for clocksource
compatible = "ezchip,nps400-timer1" <-- for clockevent
Note that name convention for timer0/timer1 was taken from legacy
ARC design. This design is our base before adding HW threads.
For backward compatibility we keep "ezchip,nps400-timer" for clocksource
Signed-off-by: Noam Camus <noamca@mellanox.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
|
|
The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
http://github.com/Broadcom/stblinux into next/dt64
Pull "Broadcom devicetree-arm64 changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM64 based SoC Device Tree changes for
4.10, please pull the following:
- Robin updates the Northstart 2 DTS to use the generic IOMMU binding
- Scott renames the Broadcom Northstar 2 binding document to use a standard name
including the brcm vendor prefix
- Kamal adds the QSPI Device Tree node to the Northstar 2 SoC and updates the
Northstar 2 SVK reference board DTS file with it enabled.
- Rob adds the Device Tree node for the Broadcom PDC (mailbox) hardware to the
Northstar 2 SoC
- Jon enables the SDIO1 block and adds proper PCIe PHYs Device Tree nodes to the
Northstar 2 SoC
- Ray adds required properties NAND controller properties to make NAND work on
the Northstar 2 SVK board, this was submitted as a 4.9 fixes and is included
here to resolve DTS file merges
- Andrea removes an incorrect power LED from the Raspberry Pi 3 DTS
- Andreas fixes the compatible string for the BCM2837 (Raspberry Pi 3)
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also uses the proper DTSI file to define the USB host mode
for the USB Device Tree nodes
* tag 'arm-soc/for-4.10/devicetree-arm64' of http://github.com/Broadcom/stblinux: (23 commits)
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
ARM64: dts: bcm2837-rpi-3-b: remove incorrect pwr LED
ARM64: bcm2835: dts: add thermal node to device-tree of bcm2837
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
arm64: dts: Add Broadcom Northstar2 device tree entries for PDC driver.
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM64: dts: bcm2835: Fix bcm2837 compatible string
arm64: dts: Update Broadcom NS2 to generic IOMMU binding
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: rename ns2.txt to brcm,ns2.txt
ARM64: dts: Add QSPI Device Tree node for NS2
ARM64: dts: bcm283x: Use dtsi for USB host mode
ARM: dts: bcm283x: drop alt3 from &gpio
ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio
ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio
ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio
...
|
|
http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
ARM: bcm2835: Add names for the RPi Zero GPIO lines
ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
ARM: dts: enable GPIO-b for Broadcom NSP
ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
ARM: dts: Add node for Broadcom OTP controller driver
ARM: dts: Enable interrupt support for cygnus crmu gpio driver
ARM: dts: Enable Broadcom iProc mailbox controller
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM: dts: cygnus: fix naming of pinctrl node
ARM: BCM53573: Specify PMU and its ILP clock in the DT
ARM: BCM5301X: Add DT for Luxul XWR-3100
ARM: BCM5301X: Add DT for Luxul XAP-1510
ARM: BCM5301X: Specify USB 3.0 PHY in DT
ARM: BCM5301X: Enable UART on Netgear R8000
ARM: BCM5301X: Add separated DTS include file for BCM47094
ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
...
|
|
into next/drivers
Merge "ARM: keystone: add TI SCI protocol support for v4.10" from
Tero Kristo:
[description taken from http://processors.wiki.ti.com/index.php/TISCI
Texas Instruments' Keystone generation System on Chips (SoC) starting
with 66AK2G02, now include a dedicated SoC System Control entity called
PMMC(Power Management Micro Controller) in line with ARM architecture
recommendations. The function of this module is to integrate all system
operations in a centralized location. Communication with the SoC System
Control entity from various processing units like ARM/DSP occurs over
Message Manager hardware block.
...
Texas Instruments' System Control Interface defines the communication
protocol between various processing entities to the System Control Entity
on TI SoCs. This is a set of message formats and sequence of operations
required to communicate and get system services processed from System
Control entity in the SoC.]
* 'for-4.10-ti-sci-base' of https://github.com/t-kristo/linux-pm:
firmware: ti_sci: Add support for reboot core service
firmware: ti_sci: Add support for Clock control
firmware: ti_sci: Add support for Device control
firmware: Add basic support for TI System Control Interface (TI-SCI) protocol
Documentation: Add support for TI System Control Interface (TI-SCI) protocol
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Pull "SCPI updates for v4.10" from Sudeep Holla:
1. Adds support for pre-v1.0 SCPI protocol versions
2. Adds support for SCPI used on Amlogic GXBB SoC platforms using the
newly added pre-v1.0 SCPI protocol
3. Decouples some platform specific details from generic SCPI binding
* tag 'scpi-updates-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
Documentation: bindings: Add support for Amlogic GXBB SCPI protocol
Documentation: bindings: add compatible specific to pre v1.0 SCPI protocols
Documentation: bindings: decouple juno specific details from generic binding
firmware: arm_scpi: allow firmware with get_capabilities not implemented
firmware: arm_scpi: add alternative legacy structures, functions and macros
firmware: arm_scpi: increase MAX_DVFS_OPPS to 16 entries
firmware: arm_scpi: add command indirection to support legacy commands
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Pull "Second Round of Renesas ARM64 Based SoC DT Updates for v4.10" from Simon Horman:
Enhancements:
* Add device nodes for PRR
* Add m3ulcb board
* Enable I2C on r8a7796/salvator-x board
* Enable SDHI0 on h3ulcb board
* tag 'renesas-arm64-dt2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7796: Add device node for PRR
arm64: dts: r8a7795: Add device node for PRR
arm64: dts: h3ulcb: rename SDHI0 pins
arm64: dts: h3ulcb: enable SDHI2
arm64: dts: m3ulcb: enable SDHI2
arm64: dts: m3ulcb: enable SDHI0
arm64: dts: m3ulcb: enable WDT
arm64: dts: m3ulcb: enable EXTALR clk
arm64: dts: m3ulcb: enable GPIO keys
arm64: dts: m3ulcb: enable GPIO leds
arm64: dts: m3ulcb: enable SCIF clk and pins
arm64: dts: m3ulcb: initial device tree
arm64: dts: m3ulcb: add M3ULCB board DT bindings
arm64: dts: h3ulcb: update header
arm64: dts: h3ulcb: update documentation with official board name
arm64: dts: r8a7796: salvator-x: enable I2C
arm64: dts: r8a7796: Enable I2C DMA
arm64: dts: r8a7796: add I2C support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Merge "Renesas ARM Based SoC Match Updates for v4.10" from Simon Horman:
* Identify SoC and register with the SoC bus
* tag 'renesas-soc-match-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: Identify SoC and register with the SoC bus
ARM: shmobile: Document DT bindings for Product Register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Pull "Renesas ARM Based SoC r8a7745 SYSC Driver Updates for v4.10" from Simon Horman:
* Add support for the r8a7745 SoC to rcar-sysc
* tag 'renesas-r8a7745-sysc-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: rcar-sysc: add R8A7745 support
ARM: shmobile: r8a7745: add power domain index macros
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add very basic ti-tfp410 DVI transmitter driver. The only feature
separating this from a completely dummy bridge is the EDID read
support trough DDC I2C. Even that functionality should be in a
separate generic connector driver. However, because of missing DRM
infrastructure support the connector is implemented within the bridge
driver. Some tfp410 HW specific features may be added later if needed,
because there is a set of registers behind i2c if it is connected.
This implementation is tested against my new tilcdc bridge support
and it works with BeagleBone DVI-D Cape Rev A3. A DT binding document
is also updated.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Move "ti,tfp410.txt" from display/ti to display/bridge before adding
generic (non omapdrm/dss specific) implementation and new features.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Exynos5433 SoC has MFC v8 hardware module, but it has more
complex clock hierarchy, so a new compatible is added.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
Big thing is that drm-misc is now officially a group maintainer/committer
model thing, with MAINTAINERS suitably updated. Otherwise just the usual
pile of misc things all over, nothing that stands out this time around.
* tag 'drm-misc-next-2016-11-29' of git://anongit.freedesktop.org/git/drm-misc: (33 commits)
drm: Introduce drm_framebuffer_assign()
drm/bridge: adv7511: Enable the audio data and clock pads on adv7533
drm/bridge: adv7511: Add Audio support
drm/edid: Consider alternate cea timings to be the same VIC
drm/atomic: Constify drm_atomic_crtc_needs_modeset()
drm: bridge: dw-hdmi: add ASoC dependency
drm: Fix shift operations for drm_fb_helper::drm_target_preferred()
drm: Avoid NULL dereference for DRM_LEGACY debug message
drm: Use u64_to_user_ptr() helper for blob ioctls
drm: Fix conflicting macro parameter in drm_mm_for_each_node_in_range()
drm: Fixup kernel doc for driver->gem_create_object
drm/hisilicon/hibmc: mark PM functions __maybe_unused
drm/hisilicon/hibmc: Checking for NULL instead of IS_ERR()
drm: bridge: add DesignWare HDMI I2S audio support
drm: Check against color expansion in drm_mm_reserve_node()
drm: Define drm_mm_for_each_node_in_range()
drm/doc: Fix links in drm_property.c
MAINTAINERS: Add link to drm-misc documentation
vgaarb: use valid dev pointer in vgaarb_info()
drm/atomic: Unconfuse the old_state mess in commmit_tail
...
|