| Age | Commit message (Collapse) | Author |
|---|
|
The binding has a typo where resets-names should read reset-names, which in
turn leads to a warning when the example is validated, since reset-names is
being used, and the binding prevent the usage of any property that isn't
described.
Fixes: 088e88be5a38 ("dt-bindings: phy: add binding for the Lantiq VRX200 and ARX300 PCIe PHYs")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The example contains an SPI bus and device, but doesn't have the
appropriate size and address cells size.
This creates a DTC warning when the example is compiled since the default
ones will not match what the device uses. Let's add them to remove that
warning.
Fixes: f7356e47032c ("dt-bindings: iio: adc: ad7192: Add binding documentation for AD7192")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The AD7192 binding describes two regulator properties, avdd-supply and
dvdd-supply, but describes it as a constant string that must be avdd and
dvdd. This is wrong since a *-supply property is actually a phandle, and
results in warnings when the example is validated (or any device tree using
that device, for that matter).
Let's remove that requirement.
Fixes: f7356e47032c ("dt-bindings: iio: adc: ad7192: Add binding documentation for AD7192")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The linux,rc-map-name property is described using an enum, yet a value has
been put in that enum twice, resulting in a warning. Let's fix that.
Fixes: 7c31b9d67342 ("media: dt-bindings: media: Add YAML schemas for the generic RC bindings")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The fsl,dsp binding requires a memory-region, yet its example doesn't have
one which results in a warning. Let's add a memory-region phandle to the
example.
Fixes: 7db2f2dfc701 ("dt-bindings: dsp: fsl: Add DSP core binding support")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Add Amit Kucheria as thermal subsystem Reviewer (Amit Kucheria)
- Fix a use after free bug when unregistering thermal zone devices (Ido
Schimmel)
- Fix thermal core framework to use put_device() when device_register()
fails (Yue Hu)
- Enable intel_pch_thermal and MMIO RAPL support for Intel Icelake
platform (Srinivas Pandruvada)
- Add clock operations in qorip thermal driver, for some platforms with
clock control like i.MX8MQ (Anson Huang)
- A couple of trivial fixes and cleanups for thermal core and different
soc thermal drivers (Amit Kucheria, Christophe JAILLET, Chuhong Yuan,
Fuqian Huang, Kelsey Skunberg, Nathan Huckleberry, Rishi Gupta,
Srinivas Kandagatla)
* 'for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
MAINTAINERS: Add Amit Kucheria as reviewer for thermal
thermal: Add some error messages
thermal: Fix use-after-free when unregistering thermal zone device
thermal/drivers/core: Use put_device() if device_register() fails
thermal_hwmon: Sanitize thermal_zone type
thermal: intel: Use dev_get_drvdata
thermal: intel: int3403: replace printk(KERN_WARN...) with pr_warn(...)
thermal: intel: int340x_thermal: Remove unnecessary acpi_has_method() uses
thermal: int340x: processor_thermal: Add Ice Lake support
drivers: thermal: qcom: tsens: Fix memory leak from qfprom read
thermal: tegra: Fix a typo
thermal: rcar_gen3_thermal: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
thermal: armada: Fix -Wshift-negative-value
dt-bindings: thermal: qoriq: Add optional clocks property
thermal: qoriq: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
thermal: qoriq: Use devm_platform_ioremap_resource() instead of of_iomap()
thermal: qoriq: Fix error path of calling qoriq_tmu_register_tmu_zone fail
thermal: qoriq: Add clock operations
drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- addition of AST2600, i.MX7ULP and F81803 watchdog support
- removal of the w90x900 and ks8695 drivers
- ziirave_wdt improvements
- small fixes and improvements
* tag 'linux-watchdog-5.4-rc1' of git://www.linux-watchdog.org/linux-watchdog: (51 commits)
watchdog: f71808e_wdt: Add F81803 support
watchdog: qcom: remove unnecessary variable from private storage
watchdog: qcom: support pre-timeout when the bark irq is available
watchdog: imx_sc: this patch just fixes whitespaces
watchdog: apseed: Add access_cs0 option for alt-boot
watchdog: aspeed: add support for dual boot
watchdog: orion_wdt: use timer1 as a pretimeout
watchdog: Add i.MX7ULP watchdog support
dt-bindings: watchdog: Add i.MX7ULP bindings
dt-bindings: watchdog: sun4i: Add the watchdog clock
dt-bindings: watchdog: sun4i: Add the watchdog interrupts
dt-bindings: watchdog: Convert Allwinner watchdog to a schema
dt-bindings: watchdog: Add YAML schemas for the generic watchdog bindings
watchdog: aspeed: Add support for AST2600
dt-bindings: watchdog: Add ast2600 compatible
watchdog: ziirave_wdt: Update checked I2C functionality mask
watchdog: ziirave_wdt: Drop ziirave_firm_write_block_data()
watchdog: ziirave_wdt: Fix DOWNLOAD_START payload
watchdog: ziirave_wdt: Drop status polling code
watchdog: ziirave_wdt: Fix RESET_PROCESSOR payload
...
|
|
Document RZ/G2N (R8A774B1) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This updates bindings for MT7629 PWM controller.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Merrifield Basin Cove PMIC
New Device Support:
- Add support for Intel Tiger Lake to Intel LPSS PCI
- Add support for Intel Sky Lake to Intel LPSS PCI
- Add support for ST-Ericsson DB8520 to DB8500 PRCMU
New Functionality:
- Add RTC and PWRC support to MT6323
Fix-ups:
- Clean-up include files; davinci_voicecodec, asic3, sm501, mt6397
- Ignore return values from debugfs_create*(); ab3100-*, ab8500-debugfs, aat2870-core
- Device Tree changes; rn5t618, mt6397
- Use new I2C API; tps80031, 88pm860x-core, ab3100-core, bcm590xx,
da9150-core, max14577, max77693, max77843, max8907,
max8925-i2c, max8997, max8998, palmas, twl-core,
- Remove obsolete code; da9063, jz4740-adc
- Simplify semantics; timberdale, htc-i2cpld
- Add 'fall-through' tags; omap-usb-host, db8500-prcmu
- Remove superfluous prints; ab8500-debugfs, db8500-prcmu, fsl-imx25-tsadc,
intel_soc_pmic_bxtwc, qcom_rpm, sm501
- Trivial rename/whitespace/typo fixes; mt6397-core, MAINTAINERS
- Reorganise code structure; mt6397-*
- Improve code consistency; intel-lpss
- Use MODULE_SOFTDEP() helper; intel-lpss
- Use DEFINE_RES_*() helpers; mt6397-core
Bug Fixes:
- Clean-up resources; max77620
- Prevent input events being dropped on resume; intel-lpss-pci
- Prevent sleeping in IRQ context; ezx-pcap"
* tag 'mfd-next-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (48 commits)
mfd: mt6323: Add MT6323 RTC and PWRC
mfd: mt6323: Replace boilerplate resource code with DEFINE_RES_* macros
mfd: mt6397: Add mutex include
dt-bindings: mfd: mediatek: Add MT6323 Power Controller
dt-bindings: mfd: mediatek: Update RTC to include MT6323
dt-bindings: mfd: mediatek: mt6397: Change to relative paths
mfd: db8500-prcmu: Support the higher DB8520 ARMSS
mfd: intel-lpss: Use MODULE_SOFTDEP() instead of implicit request
mfd: htc-i2cpld: Drop check because i2c_unregister_device() is NULL safe
mfd: sm501: Include the GPIO driver header
mfd: intel-lpss: Add Intel Skylake ACPI IDs
mfd: intel-lpss: Consistently use GENMASK()
mfd: Add support for Merrifield Basin Cove PMIC
mfd: ezx-pcap: Replace mutex_lock with spin_lock
mfd: asic3: Include the right header
MAINTAINERS: altera-sysmgr: Fix typo in a filepath
mfd: mt6397: Extract IRQ related code from core driver
mfd: mt6397: Rename macros to something more readable
mfd: Remove dev_err() usage after platform_get_irq()
mfd: db8500-prcmu: Mark expected switch fall-throughs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate _HPP/_HPX stuff in pci-acpi.c and simplify it
(Krzysztof Wilczynski)
- Fix incorrect PCIe device types and remove dev->has_secondary_link
to simplify code that deals with upstream/downstream ports (Mika
Westerberg)
- After suspend, restore Resizable BAR size bits correctly for 1MB
BARs (Sumit Saxena)
- Enable PCI_MSI_IRQ_DOMAIN support for RISC-V (Wesley Terpstra)
Virtualization:
- Add ACS quirks for iProc PAXB (Abhinav Ratna), Amazon Annapurna
Labs (Ali Saidi)
- Move sysfs SR-IOV functions to iov.c (Kelsey Skunberg)
- Remove group write permissions from sysfs sriov_numvfs,
sriov_drivers_autoprobe (Kelsey Skunberg)
Hotplug:
- Simplify pciehp indicator control (Denis Efremov)
Peer-to-peer DMA:
- Allow P2P DMA between root ports for whitelisted bridges (Logan
Gunthorpe)
- Whitelist some Intel host bridges for P2P DMA (Logan Gunthorpe)
- DMA map P2P DMA requests that traverse host bridge (Logan
Gunthorpe)
Amazon Annapurna Labs host bridge driver:
- Add DT binding and controller driver (Jonathan Chocron)
Hyper-V host bridge driver:
- Fix hv_pci_dev->pci_slot use-after-free (Dexuan Cui)
- Fix PCI domain number collisions (Haiyang Zhang)
- Use instance ID bytes 4 & 5 as PCI domain numbers (Haiyang Zhang)
- Fix build errors on non-SYSFS config (Randy Dunlap)
i.MX6 host bridge driver:
- Limit DBI register length (Stefan Agner)
Intel VMD host bridge driver:
- Fix config addressing issues (Jon Derrick)
Layerscape host bridge driver:
- Add bar_fixed_64bit property to endpoint driver (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC drivers separately
(Xiaowei Bao)
Mediatek host bridge driver:
- Add MT7629 controller support (Jianjun Wang)
Mobiveil host bridge driver:
- Fix CPU base address setup (Hou Zhiqiang)
- Make "num-lanes" property optional (Hou Zhiqiang)
Tegra host bridge driver:
- Fix OF node reference leak (Nishka Dasgupta)
- Disable MSI for root ports to work around design problem (Vidya
Sagar)
- Add Tegra194 DT binding and controller support (Vidya Sagar)
- Add support for sideband pins and slot regulators (Vidya Sagar)
- Add PIPE2UPHY support (Vidya Sagar)
Misc:
- Remove unused pci_block_cfg_access() et al (Kelsey Skunberg)
- Unexport pci_bus_get(), etc (Kelsey Skunberg)
- Hide PM, VC, link speed, ATS, ECRC, PTM constants and interfaces in
the PCI core (Kelsey Skunberg)
- Clean up sysfs DEVICE_ATTR() usage (Kelsey Skunberg)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Propagate errors for optional regulators and PHYs (Thierry Reding)
- Fix kernel command line resource_alignment parameter issues (Logan
Gunthorpe)"
* tag 'pci-v5.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (112 commits)
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
PCI: vmd: Fix shadow offsets to reflect spec changes
PCI: vmd: Fix config addressing when using bus offsets
PCI: dwc: Add validation that PCIe core is set to correct mode
PCI: dwc: al: Add Amazon Annapurna Labs PCIe controller driver
dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding
PCI: Add quirk to disable MSI-X support for Amazon's Annapurna Labs Root Port
PCI/VPD: Prevent VPD access for Amazon's Annapurna Labs Root Port
PCI: Add ACS quirk for Amazon Annapurna Labs root ports
PCI: Add Amazon's Annapurna Labs vendor ID
MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer
PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
PCI: Get rid of dev->has_secondary_link flag
...
|
|
- Fix typos and whitespace errors (Bjorn Helgaas, Krzysztof Wilczynski)
- Remove unnecessary "return" statements (Krzysztof Wilczynski)
- Correct of_irq_parse_pci() function documentation (Lubomir Rintel)
* pci/trivial:
PCI: Remove unnecessary returns
PCI: OF: Correct of_irq_parse_pci() documentation
PCI: Fix typos and whitespace errors
|
|
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
|
|
- Add mediatek support for MT7629 (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Add controller support for MT7629
dt-bindings: PCI: Add support for MT7629
|
|
- Make kirin_dw_pcie_ops constant (Nishka Dasgupta)
- Make DesignWare "num-lanes" property optional and remove from relevant
DTs (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
arm64: dts: fsl: Remove num-lanes property from PCIe nodes
ARM: dts: ls1021a: Remove num-lanes property from PCIe nodes
PCI: dwc: Return directly when num-lanes is not found
dt-bindings: PCI: designware: Remove the num-lanes from Required properties
PCI: kirin: Make structure kirin_dw_pcie_ops constant
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Two new drivers and the new pcf2127 feature make the bulk of the
additions. The rest are the usual fixes and new features.
Subsystem:
- add debug message when registration fails
New drivers:
- Amlogic Virtual Wake
- Freescale FlexTimer Module alarm
Drivers:
- remove superfluous error messages
- convert to i2c_new_dummy_device and devm_i2c_new_dummy_device
- Remove dev_err() usage after platform_get_irq()
- Set RTC range for: pcf2123, pcf8563, snvs.
- pcf2127: tamper detection and watchdog support
- pcf85363: fix regmap issue
- sun6i: H6 support
- remove w90x900/nuc900 driver"
* tag 'rtc-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (51 commits)
rtc: meson: mark PM functions as __maybe_unused
rtc: sc27xx: Remove clearing SPRD_RTC_POWEROFF_ALM_FLAG flag
dt-bindings: rtc: ds1307: add rx8130 compatible
rtc: sun6i: Allow using as wakeup source from suspend
rtc: pcf8563: let the core handle range offsetting
rtc: pcf8563: remove useless indirection
rtc: pcf8563: convert to devm_rtc_allocate_device
rtc: pcf8563: add Microcrystal RV8564 compatible
rtc: pcf8563: add Epson RTC8564 compatible
rtc: s35390a: convert to devm_i2c_new_dummy_device()
rtc: max77686: convert to devm_i2c_new_dummy_device()
rtc: pcf85363/pcf85263: fix regmap error in set_time
rtc: snvs: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: snvs: set range
rtc: snvs: fix possible race condition
rtc: pcf2127: bugfix: watchdog build dependency
rtc: pcf2127: add tamper detection support
rtc: pcf2127: add watchdog feature support
rtc: pcf2127: bugfix: read rtc disables watchdog
rtc: pcf2127: cleanup register and bit defines
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
"This includes DT support thanks to Srini and more work done by Intel
(Pierre) on improving cadence and intel support.
Summary:
- Add DT bindings and DT support in core
- Add debugfs support for soundwire properties
- Improvements on streaming handling to core
- Improved handling of Cadence module
- More updates and improvements to Intel driver"
* tag 'soundwire-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (30 commits)
soundwire: stream: make stream name a const pointer
soundwire: Add compute_params callback
soundwire: core: add device tree support for slave devices
dt-bindings: soundwire: add slave bindings
soundwire: bus: set initial value to port_status
soundwire: intel: handle disabled links
soundwire: intel: add debugfs register dump
soundwire: cadence_master: add debugfs register dump
soundwire: add debugfs support
soundwire: intel: remove unused variables
soundwire: intel: move shutdown() callback and don't export symbol
soundwire: cadence_master: add kernel parameter to override interrupt mask
soundwire: intel_init: add kernel module parameter to filter out links
soundwire: cadence_master: fix divider setting in clock register
soundwire: cadence_master: make use of mclk_freq property
soundwire: intel: read mclk_freq property from firmware
soundwire: add new mclk_freq field for properties
soundwire: stream: remove unnecessary variable initializations
soundwire: stream: fix disable sequence
soundwire: include mod_devicetable.h to avoid compiling warnings
...
|
|
Pull ARM updates from Russell King:
- fix various clang build and cppcheck issues
- switch ARM to use new common outgoing-CPU-notification code
- add some additional explanation about the boot code
- kbuild "make clean" fixes
- get rid of another "(____ptrval____)", this time for the VDSO code
- avoid treating cache maintenance faults as a write
- add a frame pointer unwinder implementation for clang
- add EDAC support for Aurora L2 cache
- improve robustness of adjust_lowmem_bounds() finding the bounds of
lowmem.
- add reset control for AMBA primecell devices
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (24 commits)
ARM: 8906/1: drivers/amba: add reset control to amba bus probe
ARM: 8905/1: Emit __gnu_mcount_nc when using Clang 10.0.0 or newer
ARM: 8904/1: skip nomap memblocks while finding the lowmem/highmem boundary
ARM: 8903/1: ensure that usable memory in bank 0 starts from a PMD-aligned address
ARM: 8891/1: EDAC: armada_xp: Add support for more SoCs
ARM: 8888/1: EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC
ARM: 8892/1: EDAC: Add missing debugfs_create_x32 wrapper
ARM: 8890/1: l2x0: add marvell,ecc-enable property for aurora
ARM: 8889/1: dt-bindings: document marvell,ecc-enable binding
ARM: 8886/1: l2x0: support parity-enable/disable on aurora
ARM: 8885/1: aurora-l2: add defines for parity and ECC registers
ARM: 8887/1: aurora-l2: add prefix to MAX_RANGE_SIZE
ARM: 8902/1: l2c: move cache-aurora-l2.h to asm/hardware
ARM: 8900/1: UNWINDER_FRAME_POINTER implementation for Clang
ARM: 8898/1: mm: Don't treat faults reported from cache maintenance as writes
ARM: 8896/1: VDSO: Don't leak kernel addresses
ARM: 8895/1: visit mach-* and plat-* directories when cleaning
ARM: 8894/1: boot: Replace open-coded nop with macro
ARM: 8893/1: boot: Explain the 8 nops
ARM: 8876/1: fix O= building with CONFIG_FPE_FASTFPE
...
|
|
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- add debugfs nodes for querying the flash name and id
- mtd parser reorganization
SPI NOR core changes:
- always use bounce buffer for register read/writes
- move m25p80 code in spi-nor.c
- rework hwcaps selection for the spi-mem case
- rework the core in order to move the manufacturer specific code out
of it:
- regroup flash parameters in 'struct spi_nor_flash_parameter'
- add default_init() and post_sfdp() hooks to tweak the flash
parameters
- introduce the ->set_4byte(), ->convert_addr() and ->setup()
methods, to deal with manufacturer specific code
- rework the SPI NOR lock/unlock logic
- fix an error code in spi_nor_read_raw()
- fix a memory leak bug
- enable the debugfs for the partname and partid
- add support for few flashes
SPI NOR controller drivers changes:
- intel-spi:
- Whitelist 4B read commands
- Add support for Intel Tiger Lake SPI serial flash
- aspeed-smc: Add of_node_put()
- hisi-sfc: add of_node_put()
- cadence-quadspi: Fix QSPI RCU Schedule Stall
NAND core:
- Fixing typos
- Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
- Macronix: new controller driver
- Omap2: fix the number of bitflips returned
- Brcmnand: fix a pointer not iterating over all the page chunks
- W90x900: driver removed
- Onenand: fix a memory leak
- Sharpsl: missing include guard
- STM32: avoid warnings when building with W=1
- Ingenic: fix a coccinelle warning
- r852: call a helper to simplify the code
CFI core:
- Kill useless initializer in mtd_do_chip_probe()
- Fix a rare write failure seen on some cfi_cmdset_0002 compliant
Parallel NORs
- Bunch of cleanups for cfi_cmdset_0002 driver's write functions by
Tokunori Ikegami"
* tag 'mtd/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (77 commits)
mtd: pmc551: Remove set but not used variable 'soff_lo'
mtd: cfi_cmdset_0002: Fix do_erase_chip() to get chip as erasing mode
mtd: sm_ftl: Fix memory leak in sm_init_zone() error path
mtd: parsers: Move CMDLINE parser
mtd: parsers: Move OF parser
mtd: parsers: Move BCM63xx parser
mtd: parsers: Move BCM47xx parser
mtd: parsers: Move TI AR7 parser
mtd: pismo: Simplify getting the adapter of a client
mtd: phram: Module parameters add writable permissions
mtd: pxa2xx: Use ioremap_cache insted of ioremap_cached
mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"
mtd: spi-nor: Add support for mt35xu02g
mtd: rawnand: omap2: Fix number of bitflips reporting with ELM
mtd: rawnand: brcmnand: Fix ecc chunk calculation for erased page bitfips
mtd: spi-nor: remove superfluous pass of nor->info->sector_size
mtd: spi-nor: enable the debugfs for the partname and partid
mtd: mtdcore: add debugfs nodes for querying the flash name and id
mtd: spi-nor: hisi-sfc: Add of_node_put() before break
mtd: spi-nor: aspeed-smc: Add of_node_put()
...
|
|
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
|
|
The `adi,disable-energy-detect` property was implemented in an initial
version of the `adin` driver series, but after a review it was discarded in
favor of implementing the ETHTOOL_PHY_EDPD phy-tunable option.
With the ETHTOOL_PHY_EDPD control, it's possible to disable/enable
Energy-Detect-Power-Down for the `adin` PHY, so this device-tree is not
needed.
Fixes: 767078132ff9 ("dt-bindings: net: add bindings for ADIN PHY driver")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
The 'mac-mode' property is similar to 'phy-mode' and 'phy-connection-type',
which are enums of mode strings.
The 'dwmac' driver supports almost all modes declared in the 'phy-mode'
enum (except for 1 or 2). But in general, there may be a case where
'mac-mode' becomes more generic and is moved as part of phylib or netdev.
In any case, the 'mac-mode' field should be made an enum, and it also makes
sense to just reference the 'phy-connection-type' from
'ethernet-controller.yaml'. That will also make it more future-proof for new
modes.
Fixes: 9c15d3597c62 ("dt-bindings: net: dwmac: document 'mac-mode' property")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Add Spreadtrum PWM controller documentation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add the device-tree documentation for the PWM IP on the MediaTek
MT8516 SoCs.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
|
|
The documentation of skew values for the KSZ9021 PHY was misleading
because the driver implementation followed the erroneous information
given in the original KSZ9021 datasheet before it was corrected in
revision 1.2 (Feb 2014). It is probably too late to correct the driver
now because of the many existing device trees, so instead this just
corrects the documentation to explain that what you actually get is not
what you might think when looking at the device tree.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Pull drm updates from Dave Airlie:
"This is the main pull request for 5.4-rc1 merge window. I don't think
there is anything outstanding so next week should just be fixes, but
we'll see if I missed anything. I landed some fixes earlier in the
week but got delayed writing summary and sending it out, due to a mix
of sick kid and jetlag!
There are some fixes pending, but I'd rather get the main merge out of
the way instead of delaying it longer.
It's also pretty large in commit count and new amd header file size.
The largest thing is four new amdgpu products (navi12/14, arcturus and
renoir APU support).
Otherwise it's pretty much lots of work across the board, i915 has
started landing tigerlake support, lots of icelake fixes and lots of
locking reworking for future gpu support, lots of header file rework
(drmP.h is nearly gone), some old legacy hacks (DRM_WAIT_ON) have been
put into the places they are needed.
uapi:
- content protection type property for HDCP
core:
- rework include dependencies
- lots of drmP.h removals
- link rate calculation robustness fix
- make fb helper map only when required
- add connector->DDC adapter link
- DRM_WAIT_ON removed
- drop DRM_AUTH usage from drivers
dma-buf:
- reservation object fence helper
dma-fence:
- shrink dma_fence struct
- merge signal functions
- store timestamps in dma_fence
- selftests
ttm:
- embed drm_get_object struct into ttm_buffer_object
- release_notify callback
bridges:
- sii902x - audio graph card support
- tc358767 - aux data handling rework
- ti-snd64dsi86 - debugfs support, DSI mode flags support
panels:
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191, Boe
Himax8279d, Sharp LD-D5116Z01B
- TI nspire, NEC NL8048HL11, LG Philips LB035Q02, Sharp LS037V7DW01,
Sony ACX565AKM, Toppoly TD028TTEC1 Toppoly TD043MTEA1
i915:
- Initial tigerlake platform support
- Locking simplification work, general all over refactoring.
- Selftests
- HDCP debug info improvements
- DSI properties
- Icelake display PLL fixes, colorspace fixes, bandwidth fixes, DSI
suspend/resume
- GuC fixes
- Perf fixes
- ElkhartLake enablement
- DP MST fixes
- GVT - command parser enhancements
amdgpu:
- add wipe memory on release flag for buffer creation
- Navi12/14 support (may be marked experimental)
- Arcturus support
- Renoir APU support
- mclk DPM for Navi
- DC display fixes
- Raven scatter/gather support
- RAS support for GFX
- Navi12 + Arcturus power features
- GPU reset for Picasso
- smu11 i2c controller support
amdkfd:
- navi12/14 support
- Arcturus support
radeon:
- kexec fix
nouveau:
- improved display color management
- detect lack of GPU power cables
vmwgfx:
- evicition priority support
- remove unused security feature
msm:
- msm8998 display support
- better async commit support for cursor updates
etnaviv:
- per-process address space support
- performance counter fixes
- softpin support
mcde:
- DCS transfers fix
exynos:
- drmP.h cleanup
lima:
- reduce logging
kirin:
- misc clenaups
komeda:
- dual-link support
- DT memory regions
hisilicon:
- misc fixes
imx:
- IPUv3 image converter fixes
- 32-bit RGB V4L2 pixel format support
ingenic:
- more support for panel related cases
mgag200:
- cursor support fix
panfrost:
- export GPU features register to userspace
- gpu heap allocations
- per-fd address space support
pl111:
- CLD pads wiring support removed from DT
rockchip:
- rework to use DRM PSR helpers
- fix bug in VOP_WIN_GET macro
- DSI DT binding rework
sun4i:
- improve support for color encoding and range
- DDC enabled GPIO
tinydrm:
- rework SPI support
- improve MIPI-DBI support
- moved to drm/tiny
vkms:
- rework CRC tracking
dw-hdmi:
- get_eld and i2s improvements
gm12u320:
- misc fixes
meson:
- global code cleanup
- vpu feature detect
omap:
- alpha/pixel blend mode properties
rcar-du:
- misc fixes"
* tag 'drm-next-2019-09-18' of git://anongit.freedesktop.org/drm/drm: (2112 commits)
drm/nouveau/bar/gm20b: Avoid BAR1 teardown during init
drm/nouveau: Fix ordering between TTM and GEM release
drm/nouveau/prime: Extend DMA reservation object lock
drm/nouveau: Fix fallout from reservation object rework
drm/nouveau/kms/nv50-: Don't create MSTMs for eDP connectors
drm/i915: Use NOEVICT for first pass on attemping to pin a GGTT mmap
drm/i915: to make vgpu ppgtt notificaiton as atomic operation
drm/i915: Flush the existing fence before GGTT read/write
drm/i915: Hold irq-off for the entire fake lock period
drm/i915/gvt: update RING_START reg of vGPU when the context is submitted to i915
drm/i915/gvt: update vgpu workload head pointer correctly
drm/mcde: Fix DSI transfers
drm/msm: Use the correct dma_sync calls harder
drm/msm: remove unlikely() from WARN_ON() conditions
drm/msm/dsi: Fix return value check for clk_get_parent
drm/msm: add atomic traces
drm/msm/dpu: async commit support
drm/msm: async commit support
drm/msm: split power control from prepare/complete_commit
drm/msm: add kms->flush_commit()
...
|
|
'clk-actions' into clk-next
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Evict parents from parent cache when they're unregistered
* clk-cdce-regulator:
clk: clk-cdce925: Add regulator support
dt-bindings: clock: cdce925: Add regulator documentation
* clk-bcm:
clk: bcm2835: Mark PLLD_PER as CRITICAL
clk: bcm2835: Add BCM2711_CLOCK_EMMC2 support
clk: bcm2835: Introduce SoC specific clock registration
dt-bindings: bcm2835-cprman: Add bcm2711 support
* clk-evict-parent-cache:
clk: Evict unregistered clks from parent caches
* clk-actions:
clk: actions: Fix factor clk struct member access
|
|
into clk-next
* clk-renesas:
clk: renesas: cpg-mssr: Set GENPD_FLAG_ALWAYS_ON for clock domain
clk: renesas: r9a06g032: Set GENPD_FLAG_ALWAYS_ON for clock domain
clk: renesas: mstp: Set GENPD_FLAG_ALWAYS_ON for clock domain
dt-bindings: clk: emev2: Rename bindings documentation file
clk: renesas: rcar-usb2-clock-sel: Use devm_platform_ioremap_resource() helper
* clk-rockchip:
clk: rockchip: Add clock controller for the rk3308
clk: rockchip: Add dt-binding header for rk3308
dt-bindings: Add bindings for rk3308 clock controller
clk: rockchip: Fix -Wunused-const-variable in rv1108 clk driver
* clk-const:
clk: spear: Make structure i2s_sclk_masks constant
* clk-simplify:
clk/ti: Use kmemdup rather than duplicating its implementation
clk: fix devm_platform_ioremap_resource.cocci warnings
|
|
into clk-next
- Set clk_init_data pointer inside clk_hw to NULL after registration
* clk-init-destroy:
clk: Overwrite clk_hw::init with NULL during clk_register()
clk: sunxi: Don't call clk_hw_get_name() on a hw that isn't registered
clk: ti: Don't reference clk_init_data after registration
clk: qcom: Remove error prints from DFS registration
rtc: sun6i: Don't reference clk_init_data after registration
clk: zx296718: Don't reference clk_init_data after registration
clk: milbeaut: Don't reference clk_init_data after registration
clk: socfpga: deindent code to proper indentation
phy: ti: am654-serdes: Don't reference clk_init_data after registration
clk: sprd: Don't reference clk_init_data after registration
clk: socfpga: Don't reference clk_init_data after registration
clk: sirf: Don't reference clk_init_data after registration
clk: qcom: Don't reference clk_init_data after registration
clk: meson: axg-audio: Don't reference clk_init_data after registration
clk: lochnagar: Don't reference clk_init_data after registration
clk: actions: Don't reference clk_init_data after registration
* clk-doc:
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
clk: Document of_parse_clkspec() some more
clk: Remove extraneous 'for' word in comments
* clk-imx: (32 commits)
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: imx: imx8mn: fix audio pll setting
clk: imx8mn: Add necessary frequency support for ARM PLL table
clk: imx8mn: Add missing rate_count assignment for each PLL structure
clk: imx8mn: fix int pll clk gate
clk: imx8mn: Add GIC clock
clk: imx8mn: Fix incorrect parents
clk: imx8mm: Fix incorrect parents
clk: imx8mq: Fix sys3 pll references
clk: imx8mq: Unregister clks when of_clk_add_provider failed
clk: imx8mm: Unregister clks when of_clk_add_provider failed
clk: imx8mq: Mark AHB clock as critical
clk: imx8mn: Keep uart clocks on for early console
clk: imx: Remove unused function statement
clk: imx7ulp: Make sure earlycon's clock is enabled
clk: imx8mm: Switch to platform driver
clk: imx: imx8mm: fix audio pll setting
...
* clk-allwinner:
clk: sunxi-ng: h6: Allow I2S to change parent rate
clk: sunxi-ng: v3s: add Allwinner V3 support
clk: sunxi-ng: v3s: add missing clock slices for MMC2 module clocks
dt-bindings: clk: sunxi-ccu: add compatible string for V3 CCU
clk: sunxi-ng: v3s: add the missing PLL_DDR1
|
|
'clk-meson' into clk-next
- Support qcom SM8150 RPMh clks
- Set floor ops for qcom sd clks
- Support qcom QCS404 WCSS clks
- Support for Mediatek MT6779 SoCs
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
* clk-qcom:
clk: qcom: rcg: Return failure for RCG update
clk: qcom: fix QCS404 TuringCC regmap
clk: qcom: clk-rpmh: Add support for SM8150
dt-bindings: clock: Document SM8150 rpmh-clock compatible
clk: qcom: clk-rpmh: Convert to parent data scheme
dt-bindings: clock: Document the parent clocks
clk: qcom: gcc: Use floor ops for SDCC clocks
clk: qcom: gcc-qcs404: Use floor ops for sdcc clks
clk: qcom: gcc-sdm845: Use floor ops for sdcc clks
clk: qcom: define probe by index API as common API
clk: qcom: Add WCSS gcc clock control for QCS404
clk: qcom: msm8916: Don't build by default
clk: qcom: gcc: Add global clock controller driver for SM8150
dt-bindings: clock: Document gcc bindings for SM8150
clk: qcom: clk-alpha-pll: Add support for Trion PLLs
clk: qcom: clk-alpha-pll: Remove post_div_table checks
clk: qcom: clk-alpha-pll: Remove unnecessary cast
* clk-mtk:
clk: mediatek: Runtime PM support for MT8183 mcucfg clock provider
clk: mediatek: Register clock gate with device
clk: mediatek: add pericfg clocks for MT8183
dt-bindings: clock: mediatek: add pericfg for MT8183
clk: mediatek: Add MT6779 clock support
clk: mediatek: Add dt-bindings for MT6779 clocks
dt-bindings: mediatek: bindings for MT6779 clk
clk: reset: Modify reset-controller driver
* clk-armada:
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: mvebu: ap806: Fix clock name for the cluster
clk: mvebu: add CPU clock driver for Armada 7K/8K
clk: mvebu: add helper file for Armada AP and CP clocks
dt-bindings: ap806: add the cluster clock node in the syscon file
* clk-ingenic:
clk: ingenic: Use CLK_OF_DECLARE_DRIVER macro
clk: ingenic/jz4740: Fix "pll half" divider not read/written properly
* clk-meson: (23 commits)
clk: meson: g12a: add support for SM1 CPU 1, 2 & 3 clocks
clk: meson: g12a: add support for SM1 DynamIQ Shared Unit clock
clk: meson: g12a: add support for SM1 GP1 PLL
dt-bindings: clk: meson: add sm1 periph clock controller bindings
clk: meson: axg-audio: add g12a reset support
dt-bindings: clock: meson: add resets to the audio clock controller
clk: meson: g12a: expose CPUB clock ID for G12B
clk: meson: g12a: add notifiers to handle cpu clock change
clk: meson: add g12a cpu dynamic divider driver
clk: core: introduce clk_hw_set_parent()
clk: meson: remove clk input helper
clk: meson: remove ee input bypass clocks
clk: meson: clk-regmap: migrate to new parent description method
clk: meson: meson8b: migrate to the new parent description method
clk: meson: axg: migrate to the new parent description method
clk: meson: gxbb: migrate to the new parent description method
clk: meson: g12a: migrate to the new parent description method
clk: meson: remove ao input bypass clocks
clk: meson: axg-aoclk: migrate to the new parent description method
clk: meson: gxbb-aoclk: migrate to the new parent description method
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- input core allows hardware drivers to specify a [more precise]
timestamp (normally taken in top half) to better track velocity of
contacts
- input_dev instances now support "polling" mode so that drivers could
use the same object for polled and interrupt-driven operation. The
plan is to convert existing drivers and retire input_polled_dev API
- a new driver for the FlySky FS-iA6B RC receiver
- a refresh of BU21013 touchpad driver
- w90x900 keyboard and touchpad drivers are removed as the platform is
gone
- assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: sidewinder - make array seq static const, makes object smaller
Input: reset device timestamp on sync
Input: bu21013_ts - switch to using standard touchscreen properties
Input: bu21013_ts - switch to using MT-B (slotted) protocol
Input: bu21013_ts - fix suspend when wake source
Input: bu21013_ts - use interrupt from I2C client
Input: bu21013_ts - remove support for platform data
Input: bu21013_ts - convert to using managed resources
Input: bu21013_ts - remove useless comments
Input: bu21013_ts - annotate supend/resume methods as __maybe_unused
Input: bu21013_ts - rename some variables
Input: bu21013_ts - convert to use GPIO descriptors
ARM: ux500: improve BU21013 touchpad bindings
Input: i8042 - enable wakeup on a stable struct device
Input: soc_button_array - use platform_device_register_resndata()
Input: psmouse - drop all unneeded functions from mouse headers
Input: add support for polling to input devices
Input: wacom_w8001 - allocate additional space for 'phys'
Input: cros_ec_keyb - add back missing mask for event_type
Input: remove dev_err() usage after platform_get_irq()
...
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- qcom:
- enable support for ipq8074, sm1850 and sm7180
- add child device node for qcs404
- misc fixes
- mediatek:
- enable support for mt8183
- misc rejig of cmdq driver
- new client-reg dt property
- armada:
- use device-managed registration api
* tag 'mailbox-v5.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: qcom-apcs: fix max_register value
mailbox: qcom: Add support for IPQ8074 APCS
dt-bindings: mailbox: qom: Add ipq8074 APPS compatible
mailbox: qcom: Add support for Qualcomm SM8150 and SC7180 SoCs
dt-bindings: mailbox: Add APSS shared for SM8150 and SC7180 SoCs
mbox: qcom: replace integer with valid macro
mbox: qcom: add APCS child device for QCS404
mailbox: mediatek: cmdq: clear the event in cmdq initial flow
mailbox: mediatek: cmdq: support mt8183 gce function
mailbox: mediatek: cmdq: move the CMDQ_IRQ_MASK into cmdq driver data
dt-binding: gce: add binding for gce client reg property
dt-binding: gce: add gce header file for mt8183
dt-binding: gce: remove thread-num property
mailbox: armada-37xx-rwtm: Use device-managed registration API
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- a bunch of DT binding conversions to DT schema format
- clean-ups of the Arm idle-states binding
- support a default number of cells in of_for_each_phandle() when the
cells name is missing
- expose dtbs_check and dt_binding_check in the make help
- convert writting-schema.md to ReST
- HiSilicon reset controller binding updates
- add documentation for MT8516 RNG
* tag 'devicetree-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (46 commits)
of: restore old handling of cells_name=NULL in of_*_phandle_with_args()
bus: qcom: fix spelling mistake "ambigous" -> "ambiguous"
of: Let of_for_each_phandle fallback to non-negative cell_count
iommu: pass cell_count = -1 to of_for_each_phandle with cells_name
dt-bindings: arm: Convert Realtek board/soc bindings to json-schema
dt-bindings: arm: Convert Actions Semi bindings to jsonschema
dt-bindings: Correct spelling in example schema
dt-bindings: cpu: Add a support cpu type for cortex-a55
dt-bindings: gpu: mali-midgard: Add samsung exynos5250 compatible
dt-bindings: arm: idle-states: Move exit-latency-us explanation
dt-bindings: arm: idle-states: Add punctuation to improve readability
dt-bindings: arm: idle-states: Correct "constraint guarantees"
dt-bindings: arm: idle-states: Correct references to wake-up delay
dt-bindings: arm: idle-states: Use "e.g." and "i.e." consistently
pinctrl-mcp23s08: Fix property-name in dt-example
dt-bindings: Clarify interrupts-extended usage
dt-bindings: Convert Arm Mali Utgard GPU to DT schema
dt-bindings: Convert Arm Mali Bifrost GPU to DT schema
dt-bindings: Convert Arm Mali Midgard GPU to DT schema
dt-bindings: irq: Convert Allwinner NMI Controller to a schema
...
|
|
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Add the ability to abort a skcipher walk.
Algorithms:
- Fix XTS to actually do the stealing.
- Add library helpers for AES and DES for single-block users.
- Add library helpers for SHA256.
- Add new DES key verification helper.
- Add surrounding bits for ESSIV generator.
- Add accelerations for aegis128.
- Add test vectors for lzo-rle.
Drivers:
- Add i.MX8MQ support to caam.
- Add gcm/ccm/cfb/ofb aes support in inside-secure.
- Add ofb/cfb aes support in media-tek.
- Add HiSilicon ZIP accelerator support.
Others:
- Fix potential race condition in padata.
- Use unbound workqueues in padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (311 commits)
crypto: caam - Cast to long first before pointer conversion
crypto: ccree - enable CTS support in AES-XTS
crypto: inside-secure - Probe transform record cache RAM sizes
crypto: inside-secure - Base RD fetchcount on actual RD FIFO size
crypto: inside-secure - Base CD fetchcount on actual CD FIFO size
crypto: inside-secure - Enable extended algorithms on newer HW
crypto: inside-secure: Corrected configuration of EIP96_TOKEN_CTRL
crypto: inside-secure - Add EIP97/EIP197 and endianness detection
padata: remove cpu_index from the parallel_queue
padata: unbind parallel jobs from specific CPUs
padata: use separate workqueues for parallel and serial work
padata, pcrypt: take CPU hotplug lock internally in padata_alloc_possible
crypto: pcrypt - remove padata cpumask notifier
padata: make padata_do_parallel find alternate callback CPU
workqueue: require CPU hotplug read exclusion for apply_workqueue_attrs
workqueue: unconfine alloc/apply/free_workqueue_attrs()
padata: allocate workqueue internally
arm64: dts: imx8mq: Add CAAM node
random: Use wait_event_freezable() in add_hwgenerator_randomness()
crypto: ux500 - Fix COMPILE_TEST warnings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits)
misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation
habanalabs: correctly cast variable to __le32
habanalabs: show correct id in error print
habanalabs: stop using the acronym KMD
habanalabs: display card name as sensors header
habanalabs: add uapi to retrieve aggregate H/W events
habanalabs: add uapi to retrieve device utilization
habanalabs: Make the Coresight timestamp perpetual
habanalabs: explicitly set the queue-id enumerated numbers
habanalabs: print to kernel log when reset is finished
habanalabs: replace __le32_to_cpu with le32_to_cpu
habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64
habanalabs: Handle HW_IP_INFO if device disabled or in reset
habanalabs: Expose devices after initialization is done
habanalabs: improve security in Debug IOCTL
habanalabs: use default structure for user input in Debug IOCTL
habanalabs: Add descriptive name to PSOC app status register
habanalabs: Add descriptive names to PSOC scratch-pad registers
habanalabs: create two char devices per ASIC
habanalabs: change device_setup_cdev() to be more generic
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here is the big staging/iio driver update for 5.4-rc1.
Lots of churn here, with a few driver/filesystems moving out of
staging finally:
- erofs moved out of staging
- greybus core code moved out of staging
Along with that, a new filesytem has been added:
- extfat
to provide support for those devices requiring that filesystem (i.e.
transfer devices to/from windows systems or printers)
Other than that, there a number of new IIO drivers, and lots and lots
and lots of staging driver cleanups and minor fixes as people continue
to dig into those for easy changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (453 commits)
Staging: gasket: Use temporaries to reduce line length.
Staging: octeon: Avoid several usecases of strcpy
staging: vhciq_core: replace snprintf with scnprintf
staging: wilc1000: avoid twice IRQ handler execution for each single interrupt
staging: wilc1000: remove unused interrupt status handling code
staging: fbtft: make several arrays static const, makes object smaller
staging: rtl8188eu: make two arrays static const, makes object smaller
staging: rtl8723bs: core: Remove Macro "IS_MAC_ADDRESS_BROADCAST"
dt-bindings: anybus-controller: move to staging/ tree
staging: emxx_udc: remove local TRUE/FALSE definition
staging: wilc1000: look for rtc_clk clock
staging: dt-bindings: wilc1000: add optional rtc_clk property
staging: nvec: make use of devm_platform_ioremap_resource
staging: exfat: drop unused function parameter
Staging: exfat: Avoid use of strcpy
staging: exfat: use integer constants
staging: exfat: cleanup spacing for casts
staging: exfat: cleanup spacing for operators
staging: rtl8723bs: hal: remove redundant variable n
staging: pi433: Fix typo in documentation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Even in this age, people are still making new serial port silicon,
why...
Anyway, here's the TTY and Serial driver update for 5.4-rc1. Lots of
changes in here for a number of embedded serial port devices that are
being worked on because people really like to see those console
logs...
Other than that, nothing major here, no core tty changes that anyone
should care about.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (125 commits)
serial: tegra: Add PIO mode support
serial: tegra: report clk rate errors
serial: tegra: add support to adjust baud rate
serial: tegra: DT for Adjusted baud rates
serial: tegra: add support to use 8 bytes trigger
serial: tegra: set maximum num of uart ports to 8
serial: tegra: check for FIFO mode enabled status
dt-binding: serial: tegra: add new chips
serial: tegra: report error to upper tty layer
serial: tegra: flush the RX fifo on frame error
serial: tegra: avoid reg access when clk disabled
serial: tegra: add support to ignore read
serial: sprd: correct the wrong sequence of arguments
dt-bindings: serial: Convert riscv,sifive-serial to json-schema
serial: max310x: turn off transmitter before activating AutoCTS or auto transmitter flow control
serial: max310x: Properly set flags in AutoCTS mode
tty: serial: fix platform_no_drv_owner.cocci warnings
dt-bindings: serial: Document Freescale LINFlexD UART
serial: fsl_linflexuart: Update compatible string
tty: n_gsm: avoid recursive locking with async port hangup
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the
staging directory, uwb and wusb (wireless USB support), because there
are no devices that actually use this protocol anymore, and what we
have today probably doesn't work at all given that the maintainers
left many many years ago. So move it to staging where it will be
removed in a few releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups
due to the driver core changes to support that. Nothing really major,
just constant forward progress.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: usbcore: Fix slab-out-of-bounds bug during device reset
usb: cdns3: Remove redundant dev_err call in cdns3_probe()
USB: rio500: Fix lockdep violation
USB: rio500: simplify locking
usb: mtu3: register a USB Role Switch for dual role mode
usb: common: add USB GPIO based connection detection driver
usb: common: create Kconfig file
usb: roles: get usb-role-switch from parent
usb: roles: Add fwnode_usb_role_switch_get() function
device connection: Add fwnode_connection_find_match()
usb: roles: Introduce stubs for the exiting functions in role.h
dt-bindings: usb: mtu3: add properties about USB Role Switch
dt-bindings: usb: add binding for USB GPIO based connection detection driver
dt-bindings: connector: add optional properties for Type-B
dt-binding: usb: add usb-role-switch property
usbip: Implement SG support to vhci-hcd and stub driver
usb: roles: intel: Enable static DRD mode for role switch
xhci-ext-caps.c: Add property to disable Intel SW switch
usb: dwc3: remove generic PHY calibrate() calls
usb: core: phy: add support for PHY calibration
...
|
|
Add AP807 clock compatible to the bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20190805100310.29048-3-miquel.raynal@bootlin.com
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add AP807 CPU clock compatible to the bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20190805100310.29048-2-miquel.raynal@bootlin.com
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a rework of the main suspend-to-idle code flow (related
to the handling of spurious wakeups), a switch over of several users
of cpufreq notifiers to QoS-based limits, a new devfreq driver for
Tegra20, a new cpuidle driver and governor for virtualized guests, an
extension of the wakeup sources framework to expose wakeup sources as
device objects in sysfs, and more.
Specifics:
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching governor
for virtualized guests wanting to do guest-side polling in the idle
loop (Marcelo Tosatti, Joao Martins, Wanpeng Li, Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel
Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling typos
in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard Crestez,
MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski)"
* tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (126 commits)
cpuidle-haltpoll: Enable kvm guest polling when dedicated physical CPUs are available
cpuidle-haltpoll: do not set an owner to allow modunload
cpuidle-haltpoll: return -ENODEV on modinit failure
cpuidle-haltpoll: set haltpoll as preferred governor
cpuidle: allow governor switch on cpuidle_register_driver()
PM: runtime: Documentation: add runtime_status ABI document
pm-graph: make setVal unbuffered again for python2 and python3
powercap: idle_inject: Use higher resolution for idle injection
cpuidle: play_idle: Increase the resolution to usec
cpuidle-haltpoll: vcpu hotplug support
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
...
|
|
Pull dmaengine updates from Vinod Koul:
- Move Dmaengine DT bindings to YAML and convert Allwinner to schema.
- FSL dma device_synchronize implementation
- DW split acpi and of helpers and updates to driver and support for
Elkhart Lake
- Move filter fn as private for omap-dma and edma drivers and
improvements to these drivers
- Mark expected switch fall-through in couple of drivers
- Renames of shdma and nbpfaxi binding document
- Minor updates to bunch of drivers
* tag 'dmaengine-5.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (55 commits)
dmaengine: ti: edma: Use bitmap_set() instead of open coded edma_set_bits()
dmaengine: ti: edma: Only reset region0 access registers
dmaengine: ti: edma: Do not reset reserved paRAM slots
dmaengine: iop-adma.c: fix printk format warning
dmaengine: stm32-dma: Use struct_size() helper
dt-bindings: dmaengine: dma-common: Fix the dma-channel-mask property
dmanegine: ioat/dca: Use struct_size() helper
dmaengine: iop-adma: remove set but not used variable 'slots_per_op'
dmaengine: dmatest: Add support for completion polling
dmaengine: ti: omap-dma: Remove variable override in omap_dma_tx_status()
dmaengine: ti: omap-dma: Remove 'Assignment in if condition'
dmaengine: ti: edma: Remove 'Assignment in if condition'
dmaengine: dw: platform: Split OF helpers to separate module
dmaengine: dw: platform: Split ACPI helpers to separate module
dmaengine: dw: platform: Move handle check to dw_dma_acpi_controller_register()
dmaengine: dw: platform: Switch to acpi_dma_controller_register()
dmaengine: dw: platform: Use devm_platform_ioremap_resource()
dmaengine: dw: platform: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw: platform: Use struct dw_dma_chip_pdata
dmaengine: dw: Export struct dw_dma_chip_pdata for wider use
...
|
