| Age | Commit message (Collapse) | Author |
|---|
|
The documentation of skew values for the KSZ9021 PHY was misleading
because the driver implementation followed the erroneous information
given in the original KSZ9021 datasheet before it was corrected in
revision 1.2 (Feb 2014). It is probably too late to correct the driver
now because of the many existing device trees, so instead this just
corrects the documentation to explain that what you actually get is not
what you might think when looking at the device tree.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.
The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.
Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The KSZ9031 skew registers contain an offset, the chip's default value
is "neutral" which does not add any skew. Programming a 0 into a skew
property will actually set it the maximal negative adjustment and not
to a neutral position as one would expect.
Explain this situation in the devicetree binding documentation and list
the settings that the chip considers neutral.
Changing the implementation to accept negative values would have been
a better solution, but would break existing configurations.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Phy properties are expected to be found in the PHY OF node. However
this Micrel driver also allows them to be placed into the MAC OF node.
This is deprecated. Document it as such, and remove the example using
the deprecated method to prevent people copying it into new device
tree files.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Renames micrel-ksz9021.txt to micrel-ksz90x1.txt and adds documentation for
the KSZ9031 binding from patch 1. Also adds step increment information, and
note about phy fixups.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
