| Age | Commit message (Collapse) | Author |
|---|
|
The INTID mask is wrong, and is made a signed value, which has
nteresting effects in the KVM emulation. Let's sanitize it.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
drm_fb_cma code has a nice helper function to display in the debugfs
information about the underlying framebuffers used by HDLCD:
$ cat /sys/kernel/debug/dri/0/fb
fb: 1920x1200@XR24
0: offset=0 pitch=7680, obj: 0 ( 2) 001011ba 0x00000000fc300000 ffffff800a27c000 9338880
fb: 1920x1200@XR24
0: offset=0 pitch=7680, obj: 0 ( 2) 001008ca 0x00000000fba00000 ffffff8009987000 9338880
fb: 1920x1200@XR24
0: offset=0 pitch=7680, obj: 0 ( 1) 00100000 0x00000000fb100000 ffffff8008fdc000 9216000
Add the entry in HDLCD's debugfs node.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
Harden the plane_check() code to drop attempts at scaling because
that is not supported. Make hdlcd_plane_atomic_update() set the pitch
and line length registers that correctly reflect the plane's values.
And make hdlcd_crtc_mode_set_nofb() a helper function for
hdlcd_crtc_enable() rather than an exposed hook.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
event_list just reimplemented what drm_crtc_arm_vblank_event does. And
we also need to send out drm events when shutting down a pipe.
With this it's possible to use the new nonblocking commit support in
the helpers.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
Because the HDLCD driver acts as a component master it can end
up enabling the runtime PM functionality before the encoders
are initialised. This can cause crashes if the component slave
never probes (missing module) or if the PM operations kick in
before the probe finishes.
Move the enabling of the runtime PM after the component master
has finished collecting the slave components and use the DRM
atomic helpers to suspend and resume the device.
Tested-by: Robin Murphy <Robin.Murphy@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
MOV to DR6 or DR7 causes a #GP if an attempt is made to write a 1 to
any of bits 63:32. However, this is not detected at KVM_SET_DEBUGREGS
time, and the next KVM_RUN oopses:
general protection fault: 0000 [#1] SMP
CPU: 2 PID: 14987 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1
Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
[...]
Call Trace:
[<ffffffffa072c93d>] kvm_arch_vcpu_ioctl_run+0x141d/0x14e0 [kvm]
[<ffffffffa071405d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm]
[<ffffffff81241648>] do_vfs_ioctl+0x298/0x480
[<ffffffff812418a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a0f2e>] entry_SYSCALL_64_fastpath+0x12/0x71
Code: 55 83 ff 07 48 89 e5 77 27 89 ff ff 24 fd 90 87 80 81 0f 23 fe 5d c3 0f 23 c6 5d c3 0f 23 ce 5d c3 0f 23 d6 5d c3 0f 23 de 5d c3 <0f> 23 f6 5d c3 0f 0b 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00
RIP [<ffffffff810639eb>] native_set_debugreg+0x2b/0x40
RSP <ffff88005836bd50>
Testcase (beautified/reduced from syzkaller output):
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <linux/kvm.h>
#include <fcntl.h>
#include <sys/ioctl.h>
long r[8];
int main()
{
struct kvm_debugregs dr = { 0 };
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7);
memcpy(&dr,
"\x5d\x6a\x6b\xe8\x57\x3b\x4b\x7e\xcf\x0d\xa1\x72"
"\xa3\x4a\x29\x0c\xfc\x6d\x44\x00\xa7\x52\xc7\xd8"
"\x00\xdb\x89\x9d\x78\xb5\x54\x6b\x6b\x13\x1c\xe9"
"\x5e\xd3\x0e\x40\x6f\xb4\x66\xf7\x5b\xe3\x36\xcb",
48);
r[7] = ioctl(r[4], KVM_SET_DEBUGREGS, &dr);
r[6] = ioctl(r[4], KVM_RUN, 0);
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
This causes an ugly dmesg splat. Beautified syzkaller testcase:
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/kvm.h>
long r[8];
int main()
{
struct kvm_irq_routing ir = { 0 };
r[2] = open("/dev/kvm", O_RDWR);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_SET_GSI_ROUTING, &ir);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Found by syzkaller:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000120
IP: [<ffffffffa0797202>] kvm_irq_map_gsi+0x12/0x90 [kvm]
PGD 6f80b067 PUD b6535067 PMD 0
Oops: 0000 [#1] SMP
CPU: 3 PID: 4988 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1
[...]
Call Trace:
[<ffffffffa0795f62>] irqfd_update+0x32/0xc0 [kvm]
[<ffffffffa0796c7c>] kvm_irqfd+0x3dc/0x5b0 [kvm]
[<ffffffffa07943f4>] kvm_vm_ioctl+0x164/0x6f0 [kvm]
[<ffffffff81241648>] do_vfs_ioctl+0x298/0x480
[<ffffffff812418a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a1062>] tracesys_phase2+0x84/0x89
Code: b5 71 a7 e0 5b 41 5c 41 5d 5d f3 c3 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 8b 8f 10 2e 00 00 31 c0 48 89 e5 <39> 91 20 01 00 00 76 6a 48 63 d2 48 8b 94 d1 28 01 00 00 48 85
RIP [<ffffffffa0797202>] kvm_irq_map_gsi+0x12/0x90 [kvm]
RSP <ffff8800926cbca8>
CR2: 0000000000000120
Testcase:
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <linux/kvm.h>
#include <fcntl.h>
#include <sys/ioctl.h>
long r[26];
int main()
{
memset(r, -1, sizeof(r));
r[2] = open("/dev/kvm", 0);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
struct kvm_irqfd ifd;
ifd.fd = syscall(SYS_eventfd2, 5, 0);
ifd.gsi = 3;
ifd.flags = 2;
ifd.resamplefd = ifd.fd;
r[25] = ioctl(r[3], KVM_IRQFD, &ifd);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
This cannot be returned by KVM_GET_VCPU_EVENTS, so it is okay to return
EINVAL. It causes a WARN from exception_type:
WARNING: CPU: 3 PID: 16732 at arch/x86/kvm/x86.c:345 exception_type+0x49/0x50 [kvm]()
CPU: 3 PID: 16732 Comm: a.out Tainted: G W 4.4.6-300.fc23.x86_64 #1
Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
0000000000000286 000000006308a48b ffff8800bec7fcf8 ffffffff813b542e
0000000000000000 ffffffffa0966496 ffff8800bec7fd30 ffffffff810a40f2
ffff8800552a8000 0000000000000000 00000000002c267c 0000000000000001
Call Trace:
[<ffffffff813b542e>] dump_stack+0x63/0x85
[<ffffffff810a40f2>] warn_slowpath_common+0x82/0xc0
[<ffffffff810a423a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0924809>] exception_type+0x49/0x50 [kvm]
[<ffffffffa0934622>] kvm_arch_vcpu_ioctl_run+0x10a2/0x14e0 [kvm]
[<ffffffffa091c04d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm]
[<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
[<ffffffff812414a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
---[ end trace b1a0391266848f50 ]---
Testcase (beautified/reduced from syzkaller output):
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <fcntl.h>
#include <sys/ioctl.h>
#include <linux/kvm.h>
long r[31];
int main()
{
memset(r, -1, sizeof(r));
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[7] = ioctl(r[3], KVM_CREATE_VCPU, 0);
struct kvm_vcpu_events ve = {
.exception.injected = 1,
.exception.nr = 0xd4
};
r[27] = ioctl(r[7], KVM_SET_VCPU_EVENTS, &ve);
r[30] = ioctl(r[7], KVM_RUN, 0);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
This causes an ugly dmesg splat. Beautified syzkaller testcase:
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/kvm.h>
long r[8];
int main()
{
struct kvm_cpuid2 c = { 0 };
r[2] = open("/dev/kvm", O_RDWR);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 0x8);
r[7] = ioctl(r[4], KVM_SET_CPUID, &c);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Found by syzkaller:
WARNING: CPU: 3 PID: 15175 at arch/x86/kvm/x86.c:7705 __x86_set_memory_region+0x1dc/0x1f0 [kvm]()
CPU: 3 PID: 15175 Comm: a.out Tainted: G W 4.4.6-300.fc23.x86_64 #1
Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
0000000000000286 00000000950899a7 ffff88011ab3fbf0 ffffffff813b542e
0000000000000000 ffffffffa0966496 ffff88011ab3fc28 ffffffff810a40f2
00000000000001fd 0000000000003000 ffff88014fc50000 0000000000000000
Call Trace:
[<ffffffff813b542e>] dump_stack+0x63/0x85
[<ffffffff810a40f2>] warn_slowpath_common+0x82/0xc0
[<ffffffff810a423a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa09251cc>] __x86_set_memory_region+0x1dc/0x1f0 [kvm]
[<ffffffffa092521b>] x86_set_memory_region+0x3b/0x60 [kvm]
[<ffffffffa09bb61c>] vmx_set_tss_addr+0x3c/0x150 [kvm_intel]
[<ffffffffa092f4d4>] kvm_arch_vm_ioctl+0x654/0xbc0 [kvm]
[<ffffffffa091d31a>] kvm_vm_ioctl+0x9a/0x6f0 [kvm]
[<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
[<ffffffff812414a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
Testcase:
#include <unistd.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <string.h>
#include <linux/kvm.h>
long r[8];
int main()
{
memset(r, -1, sizeof(r));
r[2] = open("/dev/kvm", O_RDONLY|O_TRUNC);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0x0ul);
r[5] = ioctl(r[3], KVM_SET_TSS_ADDR, 0x20000000ul);
r[7] = ioctl(r[3], KVM_SET_TSS_ADDR, 0x20000000ul);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Intel CPUs having Turbo Boost feature implement an MSR to provide a
control interface via rdmsr/wrmsr instructions. One could detect the
presence of this feature by issuing one of these instructions and
handling the #GP exception which is generated in case the referenced MSR
is not implemented by the CPU.
KVM's vCPU model behaves exactly as a real CPU in this case by injecting
a fault when MSR_IA32_PERF_CTL is called (which KVM does not support).
However, some operating systems use this register during an early boot
stage in which their kernel is not capable of handling #GP correctly,
causing #DP and finally a triple fault effectively resetting the vCPU.
This patch implements a dummy handler for MSR_IA32_PERF_CTL to avoid the
crashes.
Signed-off-by: Dmitry Bilunov <kmeaw@yandex-team.ru>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
In theory, nothing prevents the compiler from write-tearing PTEs, or
split PTE writes. These partially-modified PTEs can be fetched by other
cores and cause mayhem. I have not really encountered such case in
real-life, but it does seem possible.
For example, the compiler may try to do something creative for
kvm_set_pte_rmapp() and perform multiple writes to the PTE.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM Fixes for v4.7-rc2
Fixes for the vgic, 2 of the patches address a bug introduced in v4.6
while the rest are for the new vgic.
|
|
PTRACE_SETVFPREGS fails to properly mark the VFP register set to be
reloaded, because it undoes one of the effects of vfp_flush_hwstate().
Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to
an invalid CPU number, but vfp_set() overwrites this with the original
CPU number, thereby rendering the hardware state as apparently "valid",
even though the software state is more recent.
Fix this by reverting the previous change.
Cc: <stable@vger.kernel.org>
Fixes: 8130b9d7b9d8 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers")
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Simon Marchi <simon.marchi@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When changing the active bit from an MMIO trap, we decide to
explode if the intid is that of a private interrupt.
This flawed logic comes from the fact that we were assuming that
kvm_vcpu_kick() as called by kvm_arm_halt_vcpu() would not return before
the called vcpu responded, but this is not the case, so we need to
perform this wait even for private interrupts.
Dropping the BUG_ON seems like the right thing to do.
[ Commit message tweaked by Christoffer ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Now the the HS-DDR mode clock timings have been corrected, we can
re-enable these modes on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MMC clock timings were incorrectly calculated, when the conversion
from delay value to delay phase was done.
The 50M DDR and 50M DDR 8bit timings are off, and make eMMC DDR
unusable. Unfortunately it seems different controllers on the same SoC
have different timings. The new settings are taken from mmc2, which is
commonly used with eMMC.
The settings for the slower timing modes seem to work despite being
wrong, so leave them be.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When IS_ERR_VALUE was removed from the mmc core code, it was replaced
with a simple not-zero check. This does not work, as the value checked
is the return value for mmc_select_bus_width, which returns the set
bit width on success. This made eMMC modes higher than HS-DDR unusable.
Fix this by checking for a positive return value instead.
Fixes: 287980e49ffc ("remove lots of IS_ERR_VALUE abuses")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/fdmanana/linux into for-linus-4.7
|
|
Roland Dreier reports that one of his systems cannot boot because of
the changes made by commit ac212b6980d8 (ACPI / processor: Use common
hotplug infrastructure).
The problematic part of it is the request_region() call in
acpi_processor_get_info() that used to run at module init time before
the above commit and now it runs much earlier. Unfortunately, the
region(s) reserved by it fall into a range the PCI subsystem attempts
to reserve for AHCI IO BARs. As a result, the PCI reservation fails
and AHCI doesn't work, while previously the PCI reservation would
be made before acpi_processor_get_info() and it would succeed.
That request_region() call, however, was overlooked by commit
ac212b6980d8, as it is not necessary for the enumeration of the
processors. It only is needed when the ACPI processor driver
actually attempts to handle them which doesn't happen before
loading the ACPI processor driver module. Therefore that call
should have been moved from acpi_processor_get_info() into that
module.
Address the problem by moving the request_region() call in question
out of acpi_processor_get_info() and use the observation that the
region reserved by it is only needed if the FADT-based CPU
throttling method is going to be used, which means that it should
be sufficient to invoke it from acpi_processor_get_throttling_fadt().
Fixes: ac212b6980d8 (ACPI / processor: Use common hotplug infrastructure)
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
mediatek-drm fixes
- remove an invalid, unreachable error message and NULL pointer dereference
- remove a spurious drm_connector_unregister call from the DSI driver
* tag 'mediatek-drm-fixes-2016-06-01' of git://git.pengutronix.de/git/pza/linux:
drm/mediatek: mtk_dsi: Remove spurious drm_connector_unregister
drm/mediatek: mtk_dpi: remove invalid error message
|
|
The address check in acpi_hw_get_access_bit_width() should be byte width
based, not bit width based. This patch fixes this mistake.
For those who want to review acpi_hw_access_bit_width(), here is the
concerns and the design details of the function:
It is supposed that the GAS Address field should be aligned to the byte
width indicated by the GAS AccessSize field. Similarly, for the old non
GAS register, it is supposed that its Address should be aligned to its
Length.
For the "AccessSize = 0 (meaning ANY)" case, we try to return the maximum
instruction width (64 for MMIO or 32 for PIO) or the user expected access
bit width (64 for acpi_read()/acpi_write() or 32 for acpi_hw_read()/
acpi_hw_write()) and it is supposed that the GAS Address field should
always be aligned to the maximum expected access bit width (otherwise it
can't be accessed using ANY access bit width).
The problem is in acpi_tb_init_generic_address(), where the non GAS
register's Length is converted into the GAS BitWidth field, its Address is
converted into the GAS Address field, and the GAS AccessSize field is left
0 but most of the registers actually cannot be accessed using "ANY"
accesses.
As a conclusion, when AccessSize = 0 (ANY), the Address should either be
aligned to the BitWidth (wrong conversion) or aligned to 32 for PIO or 64
for MMIO (real GAS). Since currently, max_bit_width is 32, then:
1. BitWidth for the wrong conversion is 8,16,32; and
2. The Address of the real GAS should always be aligned to 8,16,32.
The address alignment check to exclude false matched real GAS is not
necessary. Thus this patch fixes the issue by removing the address
alignment check.
On the other hand, we in fact could use a simpler check of
"reg->bit_width < max_bit_width" to exclude the "BitWidth=64 PIO" case that
may be issued from acpi_read()/acpi_write() in the future.
Fixes: b314a172ee96 (ACPICA: Hardware: Add optimized access bit width support)
Reported-and-tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The return value of clamp_val() has to be stored actually.
Fixes: b7898fda5bc7 (cpufreq: Support for fast frequency switching)
Reported-by: Steve Muckle <steve.muckle@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for v4.7. Not much, and just driver
fixes:
- add device tree matches to MAINTAINERS
- inversion bug in the Nomadik driver
- dual edge handling bug in the mediatek driver"
* tag 'pinctrl-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: fix dual-edge code defect
MAINTAINERS: Add file patterns for pinctrl device tree bindings
pinctrl: nomadik: fix inversion of gpio direction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
- use of vma_pages instead of explicit computation
- DocBook and headerdoc updates for dma-buf
* tag 'dma-buf-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
dma-buf: use vma_pages()
fence: add missing descriptions for fence
doc: update/fixup dma-buf related DocBook
reservation: add headerdoc comments
dma-buf: headerdoc fixes
|
|
In commit 86d3473224b0 some of the checking for a valid timeval
was subtley changed which caused -EINVAL to be returned whenever
the timeval was null.
However, it is possible to set the timezone data while specifying
a NULL timeval, which is usually done to handle systems where the
RTC keeps local time instead of UTC. Thus the patch causes such
systems to have the time incorrectly set.
This patch addresses the issue by handling the error conditionals
in the same way as was done previously.
Fixes: 86d3473224b0 "time: Introduce do_sys_settimeofday64()"
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Baolin Wang <baolin.wang@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Link: http://lkml.kernel.org/r/1464807207-16530-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We're missing entries for mlock2, copy_file_range, preadv2 and pwritev2
in our compat syscall table, so hook them up. Only the last two need
compat wrappers.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Connectors are unregistered by mtk_drm_drv via drm_connector_unregister_all().
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Do not try to dereference dpi if it is NULL.
Since dpi can never be NULL when mtk_dpi_set_display_mode() is called,
remove the message.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
If kmalloc() returned NULL we would end up dereferencing "state" a
couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Reset crtc->state to NULL after freeing the state object and call
__drm_atomic_helper_crtc_destroy_state() helper instead of manually
calling drm_property_unreference_blob().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
There are several issues in fscache revalidation code.
- In ceph_revalidate_work(), fscache_invalidate() is called when
fscache_check_consistency() return 0. This is complete wrong
because 0 means cache is valid.
- Handle_cap_grant() calls ceph_queue_revalidate() if client
already has CAP_FILE_CACHE. This code is confusing. Client
should revalidate the cache each time it got CAP_FILE_CACHE
anew.
- In Handle_cap_grant(), fscache_invalidate() is called if MDS
revokes CAP_FILE_CACHE. This is inconsistency with the case
that inode get evicted. In the later case, the cache is not
discarded. Client may use the cache when inode is reloaded.
This patch moves the fscache revalidation into ceph_get_caps().
Client revalidates the cache after it gets CAP_FILE_CACHE.
i_rdcache_gen should keep constance while CAP_FILE_CACHE is
used. If i_fscache_gen is not equal to i_rdcache_gen, client
needs to check cache's consistency.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
All other filesystems do not add dirty pages to fscache. They all
disable fscache when inode is opened for write. Only ceph adds
dirty pages to fscache, but the code is buggy.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
ceph_fill_file_size() has already called ceph_fscache_invalidate()
if it return true.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
If readpages fails, fscache needs to cleanup its internal state.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
__fscache_check_consistency() calls check_consistency() callback
and return the callback's return value. But the return type of
check_consistency() is bool. So __fscache_check_consistency()
return 1 if the cache is inconsistent. This is inconsistent with
the document.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
|
|
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
|
|
Pull networking fixes from David Miller:
1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.
2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
properly. From Ezequiel Garcia.
3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.
4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.
5) Fix deadlock on team->lock when propagating features, from Ivan
Vecera.
6) Work around buffer offset hw bug in alx chips, from Feng Tang.
7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
Long.
8) Various statistics bug fixes in mlx4 from Eric Dumazet.
9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.
10) All of l2tp was namespace aware, but the ipv6 support code was not
doing so. From Shmulik Ladkani.
11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.
12) Propagate MAC changes properly through VLAN devices, from Mike
Manning.
13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
sfc: Track RPS flow IDs per channel instead of per function
usbnet: smsc95xx: fix link detection for disabled autonegotiation
virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
bnx2x: avoid leaking memory on bnx2x_init_one() failures
fou: fix IPv6 Kconfig options
openvswitch: update checksum in {push,pop}_mpls
sctp: sctp_diag should dump sctp socket type
net: fec: update dirty_tx even if no skb
vlan: Propagate MAC address to VLANs
atm: iphase: off by one in rx_pkt()
atm: firestream: add more reserved strings
vxlan: Accept user specified MTU value when create new vxlan link
net: pktgen: Call destroy_hrtimer_on_stack()
timer: Export destroy_hrtimer_on_stack()
net: l2tp: Make l2tp_ip6 namespace aware
Documentation: ip-sysctl.txt: clarify secure_redirects
sfc: use flow dissector helpers for aRFS
ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
net: nps_enet: Disable interrupts before napi reschedule
net/lapb: tuse %*ph to dump buffers
...
|
|
- Fixed black screen for some resolutions of G200e rev4
- Fixed testm & testn which had predetermined value.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Pull sparc fixes from David Miller:
"sparc64 mmu context allocation and trap return bug fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix return from trap window fill crashes.
sparc: Harden signal return frame checks.
sparc64: Take ctx_alloc_lock properly in hugetlb_setup().
|
|
Since the introduction of (struct_mutex) lockless GEM bo freeing, there
are a pair of driver vfuncs for freeing the GEM bo, of which the driver
may choose to only implement driver->gem_object_free_unlocked (and so
avoid taking the struct_mutex along the free path). However, the CMA GEM
helpers were still calling driver->gem_free_object directly, now NULL,
and promptly dying on the fancy new lockless drivers. Oops.
Robert Foss bisected this to b82caafcf2303 (drm/vc4: Use lockless gem BO
free callback) on his vc4 device, but that just serves as an enabler for
9f0ba539d13ae (drm/gem: support BO freeing without dev->struct_mutex).
Reported-by: Robert Foss <robert.foss@collabora.com>
Fixes: 9f0ba539d13ae (drm/gem: support BO freeing without dev->struct_mutex)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Robert Foss <robert.foss@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
After commit 027b3f8ba9277410c3191d72d1ed2c6146d8a668 ("drm/modes: stop
handling framebuffer special") extra fb refs are left around when doing
atomic modesetting.
The problem is that the new drm_property_change_valid_get() does not
return anything in the '**ref' parameter, which causes
drm_property_change_valid_put() to do nothing.
For some reason this doesn't cause problems with legacy API.
Also, previously the code only set the 'ref' variable for fbs, with this
patch the 'ref' is set for all objects.
Fixes: 027b3f8ba927 ("drm/modes: stop handling framebuffer special")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm_atomic_set_mode_prop_for_crtc() does not clear the state->mode, so
old data may be left there when a new mode is set, possibly causing odd
issues.
This patch improves the situation by always clearing the state->mode
first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit 652353e6e561c2aeeac62df183f721f6f9b5b45f ("drm/sti: set CRTC
modesetting parameters") added a hack to avoid warnings related to
setting mode with atomic API. With the previous patch, the hack should
no longer be necessary.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When setting mode via MODE_ID property,
drm_atomic_set_mode_prop_for_crtc() does not call
drm_mode_set_crtcinfo() which possibly causes:
"[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 32: Can't
calculate constants, dotclock = 0!"
Whether the error is seen depends on the previous data in state->mode,
as state->mode is not cleared when setting new mode.
This patch adds drm_mode_set_crtcinfo() call to
drm_mode_convert_umode(), which is called in both legacy and atomic
paths. This should be fine as there's no reason to call
drm_mode_convert_umode() without also setting the crtc related fields.
drm_mode_set_crtcinfo() is removed from the legacy drm_mode_setcrtc() as
that is no longer needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If we do not provide the PVR for POWER8NVL, a guest on this system
currently ends up in PowerISA 2.06 compatibility mode on KVM, since QEMU
does not provide a generic PowerISA 2.07 mode yet. So some new
instructions from POWER8 (like "mtvsrd") get disabled for the guest,
resulting in crashes when using code compiled explicitly for
POWER8 (e.g. with the "-mcpu=power8" option of GCC).
Fixes: ddee09c099c3 ("powerpc: Add PVR for POWER8NVL processor")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This should not have any impact on hash, because hash does tlb
invalidate with every pte update and we don't implement
flush_tlb_* functions for hash. With radix we should make an explicit
call to flush tlb outside pte update.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When we converted the asm routines to C functions, we missed updating
HPTE_R_R based on _PAGE_ACCESSED. ASM code used to copy over the lower
bits from pte via.
andi. r3,r30,0x1fe /* Get basic set of flags */
We also update the code such that we won't update the Change bit ('C'
bit) always. This was added by commit c5cf0e30bf3d8 ("powerpc: Fix
buglet with MMU hash management").
With hash64, we need to make sure that hardware doesn't do a pte update
directly. This is because we do end up with entries in TLB with no hash
page table entry. This happens because when we find a hash bucket full,
we "evict" a more/less random entry from it. When we do that we don't
invalidate the TLB (hpte_remove) because we assume the old translation
is still technically "valid". For more info look at commit
0608d692463("powerpc/mm: Always invalidate tlb on hpte invalidate and
update").
Thus it's critical that valid hash PTEs always have reference bit set
and writeable ones have change bit set. We do this by hashing a
non-dirty linux PTE as read-only and always setting _PAGE_ACCESSED (and
thus R) when hashing anything else in. Any attempt by Linux at clearing
those bits also removes the corresponding hash entry.
Commit 5cf0e30bf3d8 did that for 'C' bit by enabling 'C' bit always.
We don't really need to do that because we never map a RW pte entry
without setting 'C' bit. On READ fault on a RW pte entry, we still map
it READ only, hence a store update in the page will still cause a hash
pte fault.
This patch reverts the part of commit c5cf0e30bf3d8 ("[PATCH] powerpc:
Fix buglet with MMU hash management") and retain the updatepp part.
- If we hit the updatepp path on native, the old code without that
commit, would fail to set C bcause native_hpte_updatepp()
was implemented to filter the same bits as H_PROTECT and not let C
through thus we would "upgrade" a RO HPTE to RW without setting C
thus causing the bug. So the real fix in that commit was the change
to native_hpte_updatepp
Fixes: 89ff725051d1 ("powerpc/mm: Convert __hash_page_64K to C")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
