| Age | Commit message (Collapse) | Author |
|---|
|
Some TSO engines might have a too heavy setup cost, that impacts
performance on hosts sending small bursts (2 MSS per packet).
This patch adds a device gso_min_segs, allowing drivers to set
a minimum segment size for TSO packets, according to the NIC
performance.
Tested on a mlx4 NIC, this allows to get a ~110% increase of
throughput when sending 2 MSS per packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Restart autonegotiation is necessary after setting EEE.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we find a general query with non-zero number of sources, we
are dropping the skb as it's malformed.
RFC3376, section 4.1.8. Number of Sources (N):
This number is zero in a General Query or a Group-Specific Query,
and non-zero in a Group-and-Source-Specific Query.
Therefore, reflect that by using kfree_skb() instead of consume_skb().
Fixes: d679c5324d9a ("igmp: avoid drop_monitor false positives")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Earlier change to use usable slave array for TLB mode had an additional
performance advantage. So extending the same logic to all other modes
that use xmit-hash for slave selection (viz 802.3AD, and XOR modes).
Also consolidating this with the earlier TLB change.
The main idea is to build the usable slaves array in the control path
and use that array for slave selection during xmit operation.
Measured performance in a setup with a bond of 4x1G NICs with 200
instances of netperf for the modes involved (3ad, xor, tlb)
cmd: netperf -t TCP_RR -H <TargetHost> -l 60 -s 5
Mode TPS-Before TPS-After
802.3ad : 468,694 493,101
TLB (lb=0): 392,583 392,965
XOR : 475,696 484,517
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's a trivial fix to display xmit_hash_policy for this new TLB mode
since it uses transmit-hash-poilicy as part of bonding-master info
(/proc/net/bonding/<bonding-interface).
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Amir Vadai says:
====================
net/mlx4_en: Optimizations to TX flow
This patchset contains optimizations to TX flow in mlx4_en driver. It also introduce
setting/getting tx copybreak, to enable controlling inline threshold dynamically.
TX flow optimizations was authored and posted to the mailing list by Eric
Dumazet [1] as a single patch. I splitted this patch to smaller patches,
Reviewed it and tested.
Changed from original patch:
- s/iowrite32be/iowrite32/, since ring->doorbell_qpn is stored as be32
The tx copybreak patch was also suggested by Eric Dumazet, and was edited and
reviewed by me. User space patch will be sent after kernel code is ready.
I am sending this patchset now since the merge window is near and don't want to
miss it.
More work need to do:
- Disable BF when xmit_more is in use
- Make TSO use xmit_more too. Maybe by splitting small TSO packets in the
driver itself, to avoid extra cpu/memory costs of GSO before the driver
- Fix mlx4_en_xmit buggy handling of queue full in the middle of a burst
partially posted to send queue using xmit_more
Eric, I edited the patches to have you as the Author and the first
signed-off-by. I hope it is ok with you (I wasn't sure if it is ok to sign by
you), anyway all the credit to those changes should go to you.
Patchset was tested and applied over commit 1e203c1 "(net: sched:
suspicious RCU usage in qdisc_watchdog")
[1] - https://patchwork.ozlabs.org/patch/394256/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of setting inline threshold using module parameter only on
driver load, use set_tunable() to set it dynamically.
No need to store the threshold per ring, using instead the netdev global
priv->prof->inline_thold
Initial value still is set using the module parameter, therefore
backward compatability is kept.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new ethtool [sg]et_tunable() to set tx_copybread (inline threshold)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reorganize code to call is_inline() once, so compiler can inline it
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Properly clear tx_info->ts_requested
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Access skb_headlen() once in tx flow
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Acces skb_shinfo(skb) once in tx flow.
Also, rename @i variable to @i_frag to avoid confusion, as the "goto
tx_drop_unmap;" relied on this @i variable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
avoid stalls
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_en_process_tx_cq() carefully fetches and writes ring->last_nr_txbb
and ring->cons only one time to avoid false sharing
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_en_free_tx_desc() uses a prefetchw(&skb->users) to speed up
consume_skb()
prefetchw(&ring->tx_queue->dql) to speed up BQL update
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add frag0_dma/frag0_byte_count into mlx4_en_tx_info to avoid a cache
line miss in TX completion for frames having one dma element. (We avoid
reading back the tx descriptor)
Note this could be extended to 2/3 dma elements later, as we have free
room in mlx4_en_tx_info
Also, mlx4_en_free_tx_desc() no longer accesses skb_shinfo(). We use a
new nr_maps fields in mlx4_en_tx_info to avoid 2 or 3 cache misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Try to allocate using kmalloc_node() first, only on failure use
vmalloc()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- doorbell_qpn is stored in the cpu_to_be32() way to avoid bswap() in fast
path.
- mdev->mr.key stored in ring->mr_key to also avoid bswap() and access to
cold cache line.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reorganize struct mlx4_en_tx_ring to have:
- One cache line containing last_nr_txbb & cons & wake_queue, used by tx
completion.
- One cache line containing fields dirtied by mlx4_en_xmit()
- Following part is read mostly and shared by cpus.
Align struct mlx4_en_tx_info to a cache line
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Remove unused variable ring->poll_cnt
- No need to set some fields if using blueflame
- Add missing const's
- Use unlikely
- Remove unneeded new line
- Make some comments more precise
- struct mlx4_bf @offset field reduced to unsigned int to save space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Standard qdisc API to setup a timer implies an atomic operation on every
packet dequeue : qdisc_unthrottled()
It turns out this is not really needed for FQ, as FQ has no concept of
global qdisc throttling, being a qdisc handling many different flows,
some of them can be throttled, while others are not.
Fix is straightforward : add a 'bool throttle' to
qdisc_watchdog_schedule_ns(), and remove calls to qdisc_unthrottled()
in sch_fq.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When fec_enet_alloc_buffers() fails we should better undo the previous actions,
which consists of: disabling the FEC clocks and putting the FEC pins into
inactive state.
The error path for fec_enet_mii_probe() is kept unchanged.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDIO_BCM_UNIMAC needs HAS_IOMEM, so depend on it, the related error (
with allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap" [drivers/net/phy/mdio-bcm-unimac.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Its unfortunate we have to walk again skb list to find the tail
after segmentation, even if data is probably hot in cpu caches.
skb_segment() can store the tail of the list into segs->prev,
and validate_xmit_skb_list() can immediately get the tail.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andy Zhou says:
====================
Add Geneve tunnel protocol support
This patch series adds kernel support for Geneve (Generic Network
Virtualization Encapsulation) based on Geneve IETF draft:
http://www.ietf.org/id/draft-gross-geneve-01.txt
Patch 1 implements Geneve tunneling protocol driver
Patch 2-6 adds openvswitch support for creating and using
Geneve tunnels by OVS user space.
v1->v2: Style fixes: use tab instead space for Kconfig
Patch 2-6 are reviewed by Pravin Shetty, add him to acked-by
Patch 6 was reviewed by Thomas Graf when commiting
to openvswitch.org, add him to acked-by.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Openvswitch implementation is completely agnostic to the options
that are in use and can handle newly defined options without
further work. It does this by simply matching on a byte array
of options and allowing userspace to setup flows on this array.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Singed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Thomas Graf <tgraf@noironetworks.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the size of the flow key grows, it can put some pressure on the
stack. This is particularly true in ovs_flow_cmd_set(), which needs several
copies of the key on the stack. One of those uses is logically separate,
so this factors it out to reduce stack pressure and improve readibility.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the flow information that is matched for tunnels and
the tunnel data passed around with packets is the same. However,
as additional information is added this is not necessarily desirable,
as in the case of pointers.
This adds a new structure for tunnel metadata which currently contains
only the existing struct. This change is purely internal to the kernel
since the current OVS_KEY_ATTR_IPV4_TUNNEL is simply a compressed version
of OVS_KEY_ATTR_TUNNEL that is translated at flow setup.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some tunnel formats have mechanisms for indicating that packets are
OAM frames that should be handled specially (either as high priority or
not forwarded beyond an endpoint). This provides support for allowing
those types of packets to be matched.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As new protocols are added, the size of the flow key tends to
increase although few protocols care about all of the fields. In
order to optimize this for hashing and matching, OVS uses a variable
length portion of the key. However, when fields are extracted from
the packet we must still zero out the entire key.
This is no longer necessary now that OVS implements masking. Any
fields (or holes in the structure) which are not part of a given
protocol will be by definition not part of the mask and zeroed out
during lookup. Furthermore, since masking already uses variable
length keys this zeroing operation automatically benefits as well.
In principle, the only thing that needs to be done at this point
is remove the memset() at the beginning of flow. However, some
fields assume that they are initialized to zero, which now must be
done explicitly. In addition, in the event of an error we must also
zero out corresponding fields to signal that there is no valid data
present. These increase the total amount of code but very little of
it is executed in non-error situations.
Removing the memset() reduces the profile of ovs_flow_extract()
from 0.64% to 0.56% when tested with large packets on a 10G link.
Suggested-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a device level support for Geneve -- Generic Network
Virtualization Encapsulation. The protocol is documented at
http://tools.ietf.org/html/draft-gross-geneve-01
Only protocol layer Geneve support is provided by this driver.
Openvswitch can be used for configuring, set up and tear down
functional Geneve tunnels.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
git checkout 1b7bde6d659d30f171259cc2dfba8e5dab34e735
make.cross ARCH=m68k m5275evb_defconfig
make.cross ARCH=m68k
All error/warnings:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_rx_queue':
>> drivers/net/ethernet/freescale/fec_main.c:1470:3: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
prefetch(skb->data - NET_IP_ALIGN);
^
cc1: some warnings being treated as errors
missed included prefetch.h
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcmgenet_mii_setup() is called from the PHY state machine every 1-2 seconds
when the PHYs are in PHY_POLL mode.
Improve bcmgenet_mii_setup() so that it touches the MAC registers only when
the link is up and there was a change to link, speed, duplex, or pause status.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Walter Lozano says:
====================
Altera TSE with no PHY
In some scenarios there is no PHY chip present, for example in optical links.
This serie of patches moves PHY get addr and MDIO create to a new function and
avoids PHY and MDIO probing in these cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids PHY and MDIO probing if no PHY chip is present.
This is the case mainly in optical links where there is no need for
PHY chip, and therefore no need of MDIO. In this scenario Ethernet
MAC is directly connected to an optical module through an external
SFP transceiver.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move PHY get addr and MDIO create to a new function to improve readability
and make it easier to avoid its usage. This will be useful for example in
the case where there is no PHY chip.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
pull request: wireless-next 2014-10-03
Please pull tihs batch of updates intended for the 3.18 stream!
For the iwlwifi bits, Emmanuel says:
"I have here a few things that depend on the latest mac80211's changes:
RRM, TPC, Quiet Period etc... Eyal keeps improving our rate control
and we have a new device ID. This last patch should probably have
gone to wireless.git, but at that stage, I preferred to send it to
-next and CC stable."
For (most of) the Atheros bits, Kalle says:
"The only new feature is testmode support from me. Ben added a new method
to crash the firmware with an assert for debug purposes. As usual, we
have lots of smaller fixes from Michal. Matteo fixed a Kconfig
dependency with debugfs. I fixed some warnings recently added to
checkpatch."
For the NFC bits, Samuel says:
"We've had major updates for TI and ST Microelectronics drivers, and a
few NCI related changes.
For TI's trf7970a driver:
- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues
For ST Microelectronics' ST21NFCA and ST21NFCB drivers:
- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes
Finally, Marvell added ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
For the Bluetooth bits, Johan says:
"This 3.18 pull request replaces the one I did on Monday ("bluetooth-next
2014-09-22", which hasn't been pulled yet). The additions since the last
request are:
- SCO connection fix for devices not supporting eSCO
- Cleanups regarding the SCO establishment logic
- Remove unnecessary return value from logging functions
- Header compression fix for 6lowpan
- Cleanups to the ieee802154/mrf24j40 driver
Here's a copy from previous request that this one replaces:
'
Here are some more patches for 3.18. They include various fixes to the
btusb HCI driver, a fix for LE SMP, as well as adding Jukka to the
MAINTAINERS file for generic 6LoWPAN (as requested by Alexander Aring).
I've held on to this pull request a bit since we were waiting for a SCO
related fix to get sorted out first. However, since the merge window is
getting closer I decided not to wait for it. If we do get the fix sorted
out there'll probably be a second small pull request later this week.
'"
And,
"Unless 3.17 gets delayed this will probably be our last -next pull request for
3.18. We've got:
- New Marvell hardware supportr
- Multicast support for 6lowpan
- Several of 6lowpan fixes & cleanups
- Fix for a (false-positive) lockdep warning in L2CAP
- Minor btusb cleanup"
On top of all that comes the usual sort of updates to ath5k, ath9k,
ath10k, brcmfmac, mwifiex, and wil6210. This time around there are
also a number of rtlwifi updates to enable some new hardware and
to reconcile the in-kernel drivers with some newer releases of the
Realtek vendor drivers. Also of note is some device tree work for
the bcma bus.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains another batch with Netfilter/IPVS updates
for net-next, they are:
1) Add abstracted ICMP codes to the nf_tables reject expression. We
introduce four reasons to reject using ICMP that overlap in IPv4
and IPv6 from the semantic point of view. This should simplify the
maintainance of dual stack rule-sets through the inet table.
2) Move nf_send_reset() functions from header files to per-family
nf_reject modules, suggested by Patrick McHardy.
3) We have to use IS_ENABLED(CONFIG_BRIDGE_NETFILTER) everywhere in the
code now that br_netfilter can be modularized. Convert remaining spots
in the network stack code.
4) Use rcu_barrier() in the nf_tables module removal path to ensure that
we don't leave object that are still pending to be released via
call_rcu (that may likely result in a crash).
5) Remove incomplete arch 32/64 compat from nft_compat. The original (bad)
idea was to probe the word size based on the xtables match/target info
size, but this assumption is wrong when you have to dump the information
back to userspace.
6) Allow to filter from prerouting and postrouting in the nf_tables bridge.
In order to emulate the ebtables NAT chains (which are actually simple
filter chains with no special semantics), we have support filtering from
this hooks too.
7) Add explicit module dependency between xt_physdev and br_netfilter.
This provides a way to detect if the user needs br_netfilter from
the configuration path. This should reduce the breakage of the
br_netfilter modularization.
8) Cleanup coding style in ip_vs.h, from Simon Horman.
9) Fix crash in the recently added nf_tables masq expression. We have
to register/unregister the notifiers to clean up the conntrack table
entries from the module init/exit path, not from the rule addition /
deletion path. From Arturo Borrero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladislav Yasevich says:
====================
bridge: Add vlan filtering support for default pvid
This series adds default pvid support to vlan filtering in the bridge.
VLAN 1 (as recommended by 802.1q spec) is used as default pvid on ports.
Then the user can over-ride this configuration by configuring their
own vlan information.
The user can additionally change the default value through the
sysfs interface (netlink coming shortly).
The user can turn off default pvid functionality by setting default
pvid to 0.
This series changes the default behavior of the bridge when
vlan filtering is turned on. Currently, ports without any vlan
filtering configured will not recevie any traffic at all. This patch
changes the behavior of the above ports to receive only untagged traffic.
Since v3:
- allocated 'changed' bitmap on the heap and re-arrange code to clean it up.
- remove extra blank lines.
- Fix patch1 to build by itself.
- Fix error recover to not add vlan 0.
- Restructure nbp_vlan_init to remove uneeded variable.
Since v2:
- Fix handling of invalid values in sysfs interface.
- Add some additional log messages.
- Fix default_pvid handling when vlan filtering is compiled out.
- Fix sparse issues with new code.
- Fix how we located the old default pvid (added a helper function).
Since v1:
- Add ability to turn off default_pvid settings.
- Drop the automiatic filtering support based on configured vlan devices (will
be its own series)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when vlan filtering is turned on on the bridge, the bridge
will drop all traffic untill the user configures the filter. This
isn't very nice for ports that don't care about vlans and just
want untagged traffic.
A concept of a default_pvid was recently introduced. This patch
adds filtering support for default_pvid. Now, ports that don't
care about vlans and don't define there own filter will belong
to the VLAN of the default_pvid and continue to receive untagged
traffic.
This filtering can be disabled by setting default_pvid to 0.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if the pvid is not set, we return an illegal vlan value
even though the pvid value is set to 0. Since pvid of 0 is currently
invalid, just return 0 instead. This makes the current and future
checks simpler.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows the user to set and retrieve default_pvid
value. A new value can only be stored when vlan filtering
is disabled.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signedness bugs may occur when using signed char for bitops,
depending on if the highest bit is ever used.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tilman Schmidt says:
====================
ISDN patches for net-next
Here's a series of patches for the ISDN CAPI subsystem and the
Gigaset ISDN driver. Please merge via net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use function usb_endpoint_num() for the bulk endpoint and store
the endpoint number in the cardstate structure instead of the raw
endpoint address value.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Field int_in_endpointAddr was set but never used. Drop it.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid cascading warnings when leaving DLE mode fails by clearing
the DLE flag before entering recovery.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last branch in command_2_index() cannot be reached since
c==0xff is already caught by the first "if".
The empty second branch makes no difference since no other branch
will be taken for c<0x0f.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suspicious RCU usage in qdisc_watchdog call needs to be done inside
rcu_read_lock/rcu_read_unlock. And then Qdisc destroy operations
need to ensure timer is cancelled before removing qdisc structure.
[ 3992.191339] ===============================
[ 3992.191340] [ INFO: suspicious RCU usage. ]
[ 3992.191343] 3.17.0-rc6net-next+ #72 Not tainted
[ 3992.191345] -------------------------------
[ 3992.191347] include/net/sch_generic.h:272 suspicious rcu_dereference_check() usage!
[ 3992.191348]
[ 3992.191348] other info that might help us debug this:
[ 3992.191348]
[ 3992.191351]
[ 3992.191351] rcu_scheduler_active = 1, debug_locks = 1
[ 3992.191353] no locks held by swapper/1/0.
[ 3992.191355]
[ 3992.191355] stack backtrace:
[ 3992.191358] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.17.0-rc6net-next+ #72
[ 3992.191360] Hardware name: /DZ77RE-75K, BIOS GAZ7711H.86A.0060.2012.1115.1750 11/15/2012
[ 3992.191362] 0000000000000001 ffff880235803e48 ffffffff8178f92c 0000000000000000
[ 3992.191366] ffff8802322224a0 ffff880235803e78 ffffffff810c9966 ffff8800a5fe3000
[ 3992.191370] ffff880235803f30 ffff8802359cd768 ffff8802359cd6e0 ffff880235803e98
[ 3992.191374] Call Trace:
[ 3992.191376] <IRQ> [<ffffffff8178f92c>] dump_stack+0x4e/0x68
[ 3992.191387] [<ffffffff810c9966>] lockdep_rcu_suspicious+0xe6/0x130
[ 3992.191392] [<ffffffff8167213a>] qdisc_watchdog+0x8a/0xb0
[ 3992.191396] [<ffffffff810f93f2>] __run_hrtimer+0x72/0x420
[ 3992.191399] [<ffffffff810f9bcd>] ? hrtimer_interrupt+0x7d/0x240
[ 3992.191403] [<ffffffff816720b0>] ? tc_classify+0xc0/0xc0
[ 3992.191406] [<ffffffff810f9c4f>] hrtimer_interrupt+0xff/0x240
[ 3992.191410] [<ffffffff8109e4a5>] ? __atomic_notifier_call_chain+0x5/0x140
[ 3992.191415] [<ffffffff8103577b>] local_apic_timer_interrupt+0x3b/0x60
[ 3992.191419] [<ffffffff8179c2b5>] smp_apic_timer_interrupt+0x45/0x60
[ 3992.191422] [<ffffffff8179a6bf>] apic_timer_interrupt+0x6f/0x80
[ 3992.191424] <EOI> [<ffffffff815ed233>] ? cpuidle_enter_state+0x73/0x2e0
[ 3992.191432] [<ffffffff815ed22e>] ? cpuidle_enter_state+0x6e/0x2e0
[ 3992.191437] [<ffffffff815ed567>] cpuidle_enter+0x17/0x20
[ 3992.191441] [<ffffffff810c0741>] cpu_startup_entry+0x3d1/0x4a0
[ 3992.191445] [<ffffffff81106fc6>] ? clockevents_config_and_register+0x26/0x30
[ 3992.191448] [<ffffffff81033c16>] start_secondary+0x1b6/0x260
Fixes: b26b0d1e8b1 ("net: qdisc: use rcu prefix and silence sparse warnings")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f7f1de51edbd ("net: dsa: start and stop the PHY state machine")
add calls to phy_start() in dsa_slave_open() respectively phy_stop() in
dsa_slave_close().
We also call phy_start_aneg() in dsa_slave_create(), and this call is
messing up with the PHY state machine, since we basically start the
auto-negotiation, and later on restart it when calling phy_start().
phy_start() does not currently handle the PHY_FORCING or PHY_AN states
properly, but such a fix would be too invasive for this window.
Fixes: f7f1de51edbd ("net: dsa: start and stop the PHY state machine")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
