| Age | Commit message (Collapse) | Author |
|---|
|
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Due to this interface down path gets
stuck forever waiting for NAPI to complete.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock).
Acquire this lock for only releasing TX buffers instead of taking it
for whole down path.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The calculation of page_ptr here is wrong in the case the read doesn't
start at an offset that is a multiple of a page.
The result is that nfs4svc_encode_compoundres sets rq_next_page to a
value one too small, and then the loop in svc_free_res_pages may
incorrectly fail to clear a page pointer in rq_respages[].
Pages left in rq_respages[] are available for the next rpc request to
use, so xdr data may be written to that page, which may hold data still
waiting to be transmitted to the client or data in the page cache.
The observed result was silent data corruption seen on an NFSv4 client.
We tag this as "fixing" 05638dc73af2 because that commit exposed this
bug, though the incorrect calculation predates it.
Particular thanks to Andrea Arcangeli and David Gilbert for analysis and
testing.
Fixes: 05638dc73af2 "nfsd4: simplify server xdr->next_page use"
Cc: stable@vger.kernel.org
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Commit 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
introduced a bug where the governors wouldn't be stopped anymore for
->target{_index}() drivers during suspend. This happens because
'cpufreq_suspended' is updated before stopping the governors during suspend
and due to this __cpufreq_governor() would return early due to this check:
/* Don't start any governor operations if we are entering suspend */
if (cpufreq_suspended)
return 0;
Fixes: 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 8e30444e1530 "cpufreq: fix cpufreq suspend/resume for intel_pstate"
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.
Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).
I verified via tracing that this change has effect.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When compiling kprobes-test-arm.c the following error has been observed
/tmp/ccoT403o.s:21439: Error: bad immediate value for offset (4168)
This is caused by the compiler spilling it's literal pool too far away
from the site which is trying to reference it with a PC relative load.
This arises because the compiler is underestimating the size of the
inline assembler code present, which apparently it approximates as 4
bytes per line or instruction.
We fix this problem by moving the operations which generate more than
4 bytes out of the text section. Specifically, moving the .ascii
directives to the .rodata section.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Joachim Eastwood reports that commit fbfb872f5f41 "ARM: 8148/1: flush
TLS and thumbee register state during exec" causes a boot-time crash
on a Cortex-M4 nommu system:
Freeing unused kernel memory: 68K (281e5000 - 281f6000)
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
task: 29834000 ti: 29832000 task.ti: 29832000
PC is at flush_thread+0x2e/0x40
LR is at flush_thread+0x21/0x40
pc : [<2800954a>] lr : [<2800953d>] psr: 4100000b
sp : 29833d60 ip : 00000000 fp : 00000001
r10: 00003cf8 r9 : 29b1f000 r8 : 00000000
r7 : 29b0bc00 r6 : 29834000 r5 : 29832000 r4 : 29832000
r3 : ffff0ff0 r2 : 29832000 r1 : 00000000 r0 : 282121f0
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
[<2800afa5>] (unwind_backtrace) from [<2800a327>] (show_stack+0xb/0xc)
[<2800a327>] (show_stack) from [<2800a963>] (__invalid_entry+0x4b/0x4c)
The problem is that set_tls is attempting to clear the TLS location in
the kernel-user helper page, which isn't set up on V7M.
Fix this by guarding the write to the kuser helper page with
a CONFIG_KUSER_HELPERS ifdef.
Fixes: fbfb872f5f41 ARM: 8148/1: flush TLS and thumbee register state during exec
Reported-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
on ARMv6
This fixes build breakage of platsmp.c if ARMv6 was chosen for compile
time options (e.g. by building allmodconfig):
$ make allmodconfig
$ make
CC arch/arm/mach-exynos/platsmp.o
/tmp/ccdQM0Eg.s: Assembler messages:
/tmp/ccdQM0Eg.s:432: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:437: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:438: Error: selected processor does not support ARM mode `dsb '
make[1]: *** [arch/arm/mach-exynos/platsmp.o] Error 1
The error was introduced in commit "ARM: EXYNOS: Move code from
hotplug.c to platsmp.c". Previously code using
v7_exit_coherency_flush() macro was built with '-march=armv7-a' flag but
this flag dissapeared during the movement.
Fix this by annotating the v7_exit_coherency_flush() asm code with
armv7-a architecture.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The correct type (SSM2602/SSM2603/SSM2604) is passed down
from the ssm2602_spi_probe()/ssm2602_spi_probe() functions,
so use that instead of hardcoding it to SSM2602 in
ssm2602_probe().
Fixes: c924dc68f737 ("ASoC: ssm2602: Split SPI and I2C code into different modules")
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.17
A few small driver specific fixes and a couple of error handling fixes
in the core.
|
|
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the Thinkpads' firmware will issue a backlight change request
through i915 operation region unconditionally on AC plug/unplug, the
backlight level used is arbitrary and thus should be ignored. This is
handled by commit 0b9f7d93ca61 (ACPI / i915: ignore firmware requests
for backlight change). Then there is a Dell laptop whose vendor backlight
interface also makes use of operation region to change backlight level
and with the above commit, that interface no long works. The condition
used to ignore the backlight change request from firmware is thus
changed to: if the vendor backlight interface is not in use and the ACPI
backlight interface is broken, we ignore the requests; oterwise, we keep
processing them.
Fixes: 0b9f7d93ca61 (ACPI / i915: ignore firmware requests for backlight change)
Link: https://lkml.org/lkml/2014/9/23/854
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe
will fail with dmesg:
[ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering
[ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X
[ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot
get CSR clock
[ 2.186503] stmmac_pci_probe: main driver probe failed
[ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering
[ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2
This patch fix the issue by breaking the dependency to devm_clk_get()
as the CSR clock can be obtained at priv->plat->clk_csr from pci driver.
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Negated expressions and sub-expressions need to have their flags checked for
TCF_EM_INVERT and their result negated accordingly.
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 8a29111c7ca6 ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 8a29111c7ca6 ("net: gro: allow to build full sized skb")
Reported-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we use WC updates of the PTE, we are responsible for notifying the
hardware when to flush its TLBs. Do so after we zap all the PTEs before
suspend (and the BIOS tries to read our GTT).
Fixes a regression from
commit 828c79087cec61eaf4c76bb32c222fbe35ac3930
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Wed Oct 16 09:21:30 2013 -0700
drm/i915: Disable GGTT PTEs on GEN6+ suspend
that survived and continue to cause harm even after
commit e568af1c626031925465a5caaab7cca1303d55c7
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 26 20:08:20 2014 +0100
drm/i915: Undo gtt scratch pte unmapping again
v2: Trivial rebase.
v3: Fixes requires pointer dances.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82340
Tested-by: ming.yao@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Todd Previte <tprevite@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When building this driver as a module, we get a helpful warning
about the return type:
drivers/cpufreq/integrator-cpufreq.c:232:2: warning: initialization from incompatible pointer type
.remove = __exit_p(integrator_cpufreq_remove),
If the remove callback returns void, the caller gets an undefined
value as it expects an integer to be returned. This fixes the
problem by passing down the value from cpufreq_unregister_driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix the following bug introduced by commit 8fec051eea73 (cpufreq:
Convert existing drivers to use cpufreq_freq_transition_{begin|end})
that forgot to move the spin_lock() in pcc_cpufreq_target() past
cpufreq_freq_transition_begin() which calls wait_event():
BUG: sleeping function called from invalid context at drivers/cpufreq/cpufreq.c:370
in_atomic(): 1, irqs_disabled(): 0, pid: 2636, name: modprobe
Preemption disabled at:[<ffffffffa04d74d7>] pcc_cpufreq_target+0x27/0x200 [pcc_cpufreq]
[ 51.025044]
CPU: 57 PID: 2636 Comm: modprobe Tainted: G E 3.17.0-default #7
Hardware name: Hewlett-Packard ProLiant DL980 G7, BIOS P66 07/07/2010
00000000ffffffff ffff88026c46b828 ffffffff81589dbd 0000000000000000
ffff880037978090 ffff88026c46b848 ffffffff8108e1df ffff880037978090
0000000000000000 ffff88026c46b878 ffffffff8108e298 ffff88026d73ec00
Call Trace:
[<ffffffff81589dbd>] dump_stack+0x4d/0x90
[<ffffffff8108e1df>] ___might_sleep+0x10f/0x180
[<ffffffff8108e298>] __might_sleep+0x48/0xd0
[<ffffffff8145b905>] cpufreq_freq_transition_begin+0x75/0x140 drivers/cpufreq/cpufreq.c:370 wait_event(policy->transition_wait, !policy->transition_ongoing);
[<ffffffff8108fc99>] ? preempt_count_add+0xb9/0xc0
[<ffffffffa04d7513>] pcc_cpufreq_target+0x63/0x200 [pcc_cpufreq] drivers/cpufreq/pcc-cpufreq.c:207 spin_lock(&pcc_lock);
[<ffffffff810e0d0f>] ? update_ts_time_stats+0x7f/0xb0
[<ffffffff8145be55>] __cpufreq_driver_target+0x85/0x170
[<ffffffff8145e4c8>] od_check_cpu+0xa8/0xb0
[<ffffffff8145ef10>] dbs_check_cpu+0x180/0x1d0
[<ffffffff8145f310>] cpufreq_governor_dbs+0x3b0/0x720
[<ffffffff8145ebe3>] od_cpufreq_governor_dbs+0x33/0xe0
[<ffffffff814593d9>] __cpufreq_governor+0xa9/0x210
[<ffffffff81459fb2>] cpufreq_set_policy+0x1e2/0x2e0
[<ffffffff8145a6cc>] cpufreq_init_policy+0x8c/0x110
[<ffffffff8145c9a0>] ? cpufreq_update_policy+0x1b0/0x1b0
[<ffffffff8108fb99>] ? preempt_count_sub+0xb9/0x100
[<ffffffff8145c6c6>] __cpufreq_add_dev+0x596/0x6b0
[<ffffffffa016c608>] ? pcc_cpufreq_probe+0x4b4/0x4b4 [pcc_cpufreq]
[<ffffffff8145c7ee>] cpufreq_add_dev+0xe/0x10
[<ffffffff81408e81>] subsys_interface_register+0xc1/0xf0
[<ffffffff8108fb99>] ? preempt_count_sub+0xb9/0x100
[<ffffffff8145b3d7>] cpufreq_register_driver+0x117/0x2a0
[<ffffffffa016c65d>] pcc_cpufreq_init+0x55/0x9f8 [pcc_cpufreq]
[<ffffffffa016c608>] ? pcc_cpufreq_probe+0x4b4/0x4b4 [pcc_cpufreq]
[<ffffffff81000298>] do_one_initcall+0xc8/0x1f0
[<ffffffff811a731d>] ? __vunmap+0x9d/0x100
[<ffffffff810eb9a0>] do_init_module+0x30/0x1b0
[<ffffffff810edfa6>] load_module+0x686/0x710
[<ffffffff810ebb20>] ? do_init_module+0x1b0/0x1b0
[<ffffffff810ee1db>] SyS_init_module+0x9b/0xc0
[<ffffffff8158f7a9>] system_call_fastpath+0x16/0x1b
Fixes: 8fec051eea73 (cpufreq: Convert existing drivers to use cpufreq_freq_transition_{begin|end})
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The reset_resume call is needed, otherwise it will break resume
on some conditions, depending on the usb ehci/xhci controller.
This reverts commit b89193e0b06f44f48e3bf897a5b5cb4a7aff3359.
Reported-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
|
|
Fixes: commit f187bc6efb7250afee0e2009b6106 ("ipv4: No need to set generic neighbour pointer")
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Two small fixes for omap dmaengine driver which fixes cyclic suspend
and resume"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: omap-dma: Restore the CLINK_CTRL in resume path
dmaengine: omap-dma: Add memory barrier to dma_resume path
|
|
Steffen Klassert says:
====================
ipv6: Return an error when adding an already existing tunnel
The ipv6 tunnel locate functions should not return an existing
tunnel if create is true. Otherwise it is possible to add the
same tunnel multiple times without getting an error.
All our ipv6 tunnels have this bug from the very beginning.
Only the sit tunnel was fixed some years ago with:
commit 8db99e57175 ("sit: Fail to create tunnel, if it already exists").
This patchset fixes the remaining ipv6 tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6gre_tunnel_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vti6_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_tnl_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'asoc/fix/core', 'asoc/fix/fsl-ssi' and 'asoc/fix/rt286' into asoc-linus
|
|
Since we cannot make sure the 'params->num_regs' will always be none
zero here, and then if it equals to zero, the kmemdup() will return
ZERO_SIZE_PTR, which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmemdup().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Assorted fixes + unifying __d_move() and __d_materialise_dentry() +
minimal regression fix for d_path() of victims of overwriting rename()
ported on top of that"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: Don't exchange "short" filenames unconditionally.
fold swapping ->d_name.hash into switch_names()
fold unlocking the children into dentry_unlock_parents_for_move()
kill __d_materialise_dentry()
__d_materialise_dentry(): flip the order of arguments
__d_move(): fold manipulations with ->d_child/->d_subdirs
don't open-code d_rehash() in d_materialise_unique()
pull rehashing and unlocking the target dentry into __d_materialise_dentry()
ufs: deal with nfsd/iget races
fuse: honour max_read and max_write in direct_io mode
shmem: fix nlink for rename overwrite directory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"This is quite late but these need to be backported anyway.
This is the fix for a long-standing cpuset bug which existed from
2009. cpuset makes use of PF_SPREAD_{PAGE|SLAB} flags to modify the
task's memory allocation behavior according to the settings of the
cpuset it belongs to; unfortunately, when those flags have to be
changed, cpuset did so directly even whlie the target task is running,
which is obviously racy as task->flags may be modified by the task
itself at any time. This obscure bug manifested as corrupt
PF_USED_MATH flag leading to a weird crash.
The bug is fixed by moving the flag to task->atomic_flags. The first
two are prepatory ones to help defining atomic_flags accessors and the
third one is the actual fix"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: PF_SPREAD_PAGE and PF_SPREAD_SLAB should be atomic flags
sched: add macros to define bitops for task atomic flags
sched: fix confusing PFA_NO_NEW_PRIVS constant
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's our last set of fixes for 3.17. Most of these are for TI
platforms, fixing some noisy Kconfig issues, runtime clock and power
issues on several platforms and NAND timings on DRA7.
There are also a couple of bug fixes for i.MX, one for QCOM and a
small fix to avoid section mismatch noise on PXA.
Diffstat looks large, partially due to some tables being updated and
thus touching many lines. The qcom gsbi change also restructures
clock management a bit and thus touches a bunch of lines.
All in all, a bit more changes than we'd like at this point, but
nothing stands out as risky either so it seems like the right thing to
send it up now instead of holding it to the merge window"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
drivers/soc: qcom: do not disable the iface clock in probe
ARM: imx: fix .is_enabled() of shared gate clock
ARM: OMAP3: Fix I/O chain clock line assertion timed out error
ARM: keystone: dts: fix bindings for pcie and usb clock nodes
bus: omap_l3_noc: Fix connID for OMAP4
ARM: DT: imx53: fix lvds channel 1 port
ARM: dts: cm-t54: fix serial console power supply.
ARM: dts: dra7-evm: Fix NAND GPMC timings
ARM: pxa: fix section mismatch warning for pxa_timer_nodt_init
ARM: OMAP: Fix Kconfig warning for omap1
|
|
Pull MIPS fixes from Ralf Baechle:
"The final round of fixes. One corner case in the math emulator and
another one in the mcount function for ftrace"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mcount: Adjust stack pointer for static trace in MIPS32
MIPS: Fix MFC1 & MFHC1 emulation for 64-bit MIPS systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This has:
- EFI revert to fix a boot regression
- early_ioremap() fix for boot failure
- KASLR fix for possible boot failures
- EFI fix for corrupted string printing
- remove a misleading EFI bootup 'failed!' error message
Unfortunately it's all rather close to the merge window"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Truncate 64-bit values when calling 32-bit OutputString()
x86/efi: Delete misleading efi_printk() error message
Revert "efi/x86: efistub: Move shared dependencies to <asm/efi.h>"
x86/kaslr: Avoid the setup_data area when picking location
x86 early_ioremap: Increase FIX_BTMAPS_SLOTS to 8
|
|
Only exchange source and destination filenames
if flags contain RENAME_EXCHANGE.
In case if executable file was running and replaced by
other file /proc/PID/exe should still show correct file name,
not the old name of the file by which it was replaced.
The scenario when this bug manifests itself was like this:
* ALT Linux uses rpm and start-stop-daemon;
* during a package upgrade rpm creates a temporary file
for an executable to rename it upon successful unpacking;
* start-stop-daemon is run subsequently and it obtains
the (nonexistant) temporary filename via /proc/PID/exe
thus failing to identify the running process.
Note that "long" filenames (> DNAiME_INLINE_LEN) are still
exchanged without RENAME_EXCHANGE and this behaviour exists
long enough (should be fixed too apparently).
So this patch is just an interim workaround that restores
behavior for "short" names as it was before changes
introduced by commit da1ce0670c14 ("vfs: add cross-rename").
See https://lkml.org/lkml/2014/9/7/6 for details.
AV: the comments about being more careful with ->d_name.hash
than with ->d_name.name are from back in 2.3.40s; they
became obsolete by 2.3.60s, when we started to unhash the
target instead of swapping hash chain positions followed
by d_delete() as we used to do when dcache was first
introduced.
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: da1ce0670c14 "vfs: add cross-rename"
Signed-off-by: Mikhail Efremov <sem@altlinux.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
and do it along with ->d_name.len there
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... renaming it into dentry_unlock_for_move() and making it more
symmetric with dentry_lock_for_move().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
it folds into __d_move() now
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... thus making it much closer to (now unreachable, BTW) IS_ROOT(dentry)
case in __d_move(). A bit more and it'll fold in.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
list_del() + list_add() is a slightly pessimised list_move()
list_del() + INIT_LIST_HEAD() is a slightly pessimised list_del_init()
Interleaving those makes the resulting code even worse. And harder to follow...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and get rid of duplicate BUG_ON() there
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The third argument of fuse_get_user_pages() "nbytesp" refers to the number of
bytes a caller asked to pack into fuse request. This value may be lesser
than capacity of fuse request or iov_iter. So fuse_get_user_pages() must
ensure that *nbytesp won't grow.
Now, when helper iov_iter_get_pages() performs all hard work of extracting
pages from iov_iter, it can be done by passing properly calculated
"maxsize" to the helper.
The other caller of iov_iter_get_pages() (dio_refill_pages()) doesn't need
this capability, so pass LONG_MAX as the maxsize argument here.
Fixes: c9c37e2e6378 ("fuse: switch to iov_iter_get_pages()")
Reported-by: Werner Baumann <werner.baumann@onlinehome.de>
Tested-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
If overwriting an empty directory with rename, then need to drop the extra
nlink.
Test prog:
#include <stdio.h>
#include <fcntl.h>
#include <err.h>
#include <sys/stat.h>
int main(void)
{
const char *test_dir1 = "test-dir1";
const char *test_dir2 = "test-dir2";
int res;
int fd;
struct stat statbuf;
res = mkdir(test_dir1, 0777);
if (res == -1)
err(1, "mkdir(\"%s\")", test_dir1);
res = mkdir(test_dir2, 0777);
if (res == -1)
err(1, "mkdir(\"%s\")", test_dir2);
fd = open(test_dir2, O_RDONLY);
if (fd == -1)
err(1, "open(\"%s\")", test_dir2);
res = rename(test_dir1, test_dir2);
if (res == -1)
err(1, "rename(\"%s\", \"%s\")", test_dir1, test_dir2);
res = fstat(fd, &statbuf);
if (res == -1)
err(1, "fstat(%i)", fd);
if (statbuf.st_nlink != 0) {
fprintf(stderr, "nlink is %lu, should be 0\n", statbuf.st_nlink);
return 1;
}
return 0;
}
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
With this alias, we don't need to load manually the module before adding an
ip6gretap interface with iproute2.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the HCA is configured in SRIOV IB mode (that is, at least one of
the ports is IB) and the probe_vf module param isn't specified,
mlx4_init_one() failed because of the following condition:
if (ib_ports && (num_vfs_argc > 1 || probe_vfs_argc > 1)) {
.....
}
The root cause for that is a mistake in the initialization of num_vfs_argc
and probe_vfs_argc. When num_vfs / probe_vf aren't given, their argument
count counterpart should be 0, fix that.
Fixes: dd41cc3bb90e ('net/mlx4: Adapt num_vfs/probed_vf params for single port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
nf pull request for net
This series contains netfilter fixes for net, they are:
1) Fix lockdep splat in nft_hash when releasing sets from the
rcu_callback context. We don't the mutex there anymore.
2) Remove unnecessary spinlock_bh in the destroy path of the nf_tables
rbtree set type from rcu_callback context.
3) Fix another lockdep splat in rhashtable. None of the callers hold
a mutex when calling rhashtable_destroy.
4) Fix duplicated error reporting from nfnetlink when aborting and
replaying a batch.
5) Fix a Kconfig issue reported by kbuild robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_carrier_off would be called when autoresuming, even though
the cable is plugged. This causes some applications do relative
actions when detecting the carrier off. Keep the status of the
carrier, and let it be modified when the linking change occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 8ef29f8aae524bd51298fb10ac6a5ce6c4c5a3d8.
The driver core already calls pinctrl_get() and claims the default
state. There is no need to replicate this in the driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
