| Age | Commit message (Collapse) | Author |
|---|
|
In v2.6, ip_rt_redirect() calls arp_bind_neighbour() which returns 0
and then the state of the neigh for the new_gw is checked. If the state
isn't valid then the redirected route is deleted. This behavior is
maintained up to v3.5.7 by check_peer_redirect() because rt->rt_gateway
is assigned to peer->redirect_learned.a4 before calling
ipv4_neigh_lookup().
After commit 5943634fc559 ("ipv4: Maintain redirect and PMTU info in
struct rtable again."), ipv4_neigh_lookup() is performed without the
rt_gateway assigned to the new_gw. In the case when rt_gateway (old_gw)
isn't zero, the function uses it as the key. The neigh is most likely
valid since the old_gw is the one that sends the ICMP redirect message.
Then the new_gw is assigned to fib_nh_exception. The problem is: the
new_gw ARP may never gets resolved and the traffic is blackholed.
So, use the new_gw for neigh lookup.
Changes from v1:
- use __ipv4_neigh_lookup instead (per Eric Dumazet).
Fixes: 5943634fc559 ("ipv4: Maintain redirect and PMTU info in struct rtable again.")
Signed-off-by: Stephen Suryaputra Lin <ssurya@ieee.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If usb_submit_urb() called from the open function fails, the following
crash may be observed.
r8152 8-1:1.0 eth0: intr_urb submit failed: -19
...
r8152 8-1:1.0 eth0: v1.08.3
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b7b
pgd = ffffffc0e7305000
[6b6b6b6b6b6b6b7b] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
...
PC is at notifier_chain_register+0x2c/0x58
LR is at blocking_notifier_chain_register+0x54/0x70
...
Call trace:
[<ffffffc0002407f8>] notifier_chain_register+0x2c/0x58
[<ffffffc000240bdc>] blocking_notifier_chain_register+0x54/0x70
[<ffffffc00026991c>] register_pm_notifier+0x24/0x2c
[<ffffffbffc183200>] rtl8152_open+0x3dc/0x3f8 [r8152]
[<ffffffc000808000>] __dev_open+0xac/0x104
[<ffffffc0008082f8>] __dev_change_flags+0xb0/0x148
[<ffffffc0008083c4>] dev_change_flags+0x34/0x70
[<ffffffc000818344>] do_setlink+0x2c8/0x888
[<ffffffc0008199d4>] rtnl_newlink+0x328/0x644
[<ffffffc000819e98>] rtnetlink_rcv_msg+0x1a8/0x1d4
[<ffffffc0008373c8>] netlink_rcv_skb+0x68/0xd0
[<ffffffc000817990>] rtnetlink_rcv+0x2c/0x3c
[<ffffffc000836d1c>] netlink_unicast+0x16c/0x234
[<ffffffc00083720c>] netlink_sendmsg+0x340/0x364
[<ffffffc0007e85d0>] sock_sendmsg+0x48/0x60
[<ffffffc0007e9c30>] SyS_sendto+0xe0/0x120
[<ffffffc0007e9cb0>] SyS_send+0x40/0x4c
[<ffffffc000203e34>] el0_svc_naked+0x24/0x28
Clean up error handling to avoid registering the notifier if the open
function is going to fail.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As found by gcc -Wmaybe-uninitialized, having a storage_bytes value other
than 2 or 4 will result in undefined behavior:
drivers/iio/temperature/maxim_thermocouple.c: In function 'maxim_thermocouple_read':
drivers/iio/temperature/maxim_thermocouple.c:141:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This probably cannot happen, but returning -EINVAL here is appropriate
and makes gcc happy and the code more robust.
Fixes: 231147ee77f3 ("iio: maxim_thermocouple: Align 16 bit big endian value of raw reads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
(cherry picked from commit 32cb7d27e65df9daa7cee8f1fdf7b259f214bee2)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Booting an EFI mixed mode kernel has been crashing since commit:
e37e43a497d5 ("x86/mm/64: Enable vmapped stacks (CONFIG_HAVE_ARCH_VMAP_STACK=y)")
The user-visible effect in my test setup was the kernel being unable
to find the root file system ramdisk. This was likely caused by silent
memory or page table corruption.
Enabling CONFIG_DEBUG_VIRTUAL=y immediately flagged the thunking code as
abusing virt_to_phys() because it was passing addresses that were not
part of the kernel direct mapping.
Use the slow version instead, which correctly handles all memory
regions by performing a page table walk.
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112210424.5157-3-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix this when building on 32-bit:
arch/x86/platform/efi/efi.c: In function ‘__efi_enter_virtual_mode’:
arch/x86/platform/efi/efi.c:911:5: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(efi_memory_desc_t *)pa);
^
arch/x86/platform/efi/efi.c:918:5: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(efi_memory_desc_t *)pa);
^
The @pa local variable is declared as phys_addr_t and that is a u64 when
CONFIG_PHYS_ADDR_T_64BIT=y. (The last is enabled on 32-bit on a PAE
build.)
However, its value comes from __pa() which is basically doing pointer
arithmetic and checking, and returns unsigned long as it is the native
pointer width.
So let's use an unsigned long too. It should be fine to do so because
the later users cast it to a pointer too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112210424.5157-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
__LINUX_IF_ETHER_H is not defined anywhere, and if_ether.h can keep itself from
double inclusion, though it uses a single underscore prefix.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After Tom patch, thoff field could point past the end of the buffer,
this could fool some callers.
If an skb was provided, skb->len should be the upper limit.
If not, hlen is supposed to be the upper limit.
Fixes: a6e544b0a88b ("flow_dissector: Jump to exit code in __skb_flow_dissect")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yibin Yang <yibyang@cisco.com
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martin KaFai Lau says:
====================
bpf: Fix bpf_redirect to an ipip/ip6tnl dev
This patch set fixes a bug in bpf_redirect(dev, flags) when dev is an
ipip/ip6tnl. The current problem is IP-EthHdr-IP is sent out instead of
IP-IP.
Patch 1 adds a dev->type test similar to dev_is_mac_header_xmit()
in act_mirred.c which is only available in net-next. We can consider to
refactor it once this patch is pulled into net-next from net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test creates two netns, ns1 and ns2. The host (the default netns)
has an ipip or ip6tnl dev configured for tunneling traffic to the ns2.
ping VIPS from ns1 <----> host <--tunnel--> ns2 (VIPs at loopback)
The test is to have ns1 pinging VIPs configured at the loopback
interface in ns2.
The VIPs are 10.10.1.102 and 2401:face::66 (which are configured
at lo@ns2). [Note: 0x66 => 102].
At ns1, the VIPs are routed _via_ the host.
At the host, bpf programs are installed at the veth to redirect packets
from a veth to the ipip/ip6tnl. The test is configured in a way so
that both ingress and egress can be tested.
At ns2, the ipip/ip6tnl dev is configured with the local and remote address
specified. The return path is routed to the dev ipip/ip6tnl.
During egress test, the host also locally tests pinging the VIPs to ensure
that bpf_redirect at egress also works for the direct egress (i.e. not
forwarding from dev ve1 to ve2).
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the bpf program calls bpf_redirect(dev, 0) and dev is
an ipip/ip6tnl, it currently includes the mac header.
e.g. If dev is ipip, the end result is IP-EthHdr-IP instead
of IP-IP.
The fix is to pull the mac header. At ingress, skb_postpull_rcsum()
is not needed because the ethhdr should have been pulled once already
and then got pushed back just before calling the bpf_prog.
At egress, this patch calls skb_postpull_rcsum().
If bpf_redirect(dev, BPF_F_INGRESS) is called,
it also fails now because it calls dev_forward_skb() which
eventually calls eth_type_trans(skb, dev). The eth_type_trans()
will set skb->type = PACKET_OTHERHOST because the mac address
does not match the redirecting dev->dev_addr. The PACKET_OTHERHOST
will eventually cause the ip_rcv() errors out. To fix this,
____dev_forward_skb() is added.
Joint work with Daniel Borkmann.
Fixes: cfc7381b3002 ("ip_tunnel: add collect_md mode to IPIP tunnel")
Fixes: 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
aoeblk contains some mysterious code, that wants to elevate the bio
vec page counts while it's under IO. That is not needed, it's
fragile, and it's causing kernel oopses for some.
Reported-by: Tested-by: Don Koch <kochd@us.ibm.com>
Tested-by: Tested-by: Don Koch <kochd@us.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes for perf {top,report} --hierarchy, from Arnaldo Carvalho de Melo:
- These are fixes for the --hierarchy view of perf top and report, fixing
output oddities, mostly related to scrolling. (Namhyung Kim)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The ns->lba_shift assumes its value to be the logarithmic of the
LA size. A previous patch duplicated the lba_shift calculation into
lightnvm. It prematurely also subtracted a 512byte shift, which commonly
is applied per-command. The 512byte shift being subtracted twice led to
data loss when restoring the logical to physical mapping table from
device and when issuing I/O commands using rrpc.
Fix offset by removing the 512byte shift subtraction when calculating
lba_shift.
Fixes: b0b4e09c1ae7 "lightnvm: control life of nvm_dev in driver"
Reported-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent regression in the 8250_dw serial driver introduced by
adding a quirk for the APM X-Gene SoC to it which uncovered an issue
related to the handling of built-in device properties in the core ACPI
device enumeration code (Heikki Krogerus)"
* tag 'acpi-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / platform: Add support for build-in properties
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two bugs in error code paths in the PM core (system-wide
suspend of devices), a device reference leak in the boot-time suspend
test code and a cpupower utility regression from the 4.7 cycle.
Specifics:
- Prevent the PM core from attempting to suspend parent devices if
any of their children, whose suspend callbacks were invoked
asynchronously, have failed to suspend during the "late" and
"noirq" phases of system-wide suspend of devices (Brian Norris).
- Prevent the boot-time system suspend test code from leaking a
reference to the RTC device used by it (Johan Hovold).
- Fix cpupower to use the return value of one of its library
functions correctly and restore the correct behavior of it when
used for setting cpufreq tunables broken during the 4.7 development
cycle (Laura Abbott)"
* tag 'pm-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / sleep: don't suspend parent when async child suspend_{noirq, late} fails
PM / sleep: fix device reference leak in test_suspend
cpupower: Correct return type of cpu_power_is_cpu_online() in cpufreq-set
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- mmap handler for dma ops as generic handler no longer works for us
[Alexey]
- Fixes for EZChip platform [Noam]
- Fix RTC clocksource driver build issue
- ARC IRQ handling fixes [Yuriy]
- Revert a recent makefile change which doesn't go well with oldish
tools out in the wild
* tag 'arc-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: MCIP: Use IDU_M_DISTRI_DEST mode if there is only 1 destination core
ARC: IRQ: Do not use hwirq as virq and vice versa
ARC: [plat-eznps] set default baud for early console
ARC: [plat-eznps] remove IPI clear from SMP operations
Revert "ARC: build: retire old toggles"
ARC: timer: rtc: implement read loop in "C" vs. inline asm
ARC: change return value of userspace cmpxchg assist syscall
arc: Implement arch-specific dma_map_ops.mmap
ARC: [SMP] avoid overriding present cpumask
ARC: Enable PERF_EVENTS in nSIM driven platforms
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Minor doc fix, a DMI match for ideapad and a fix to toshiba-wmi to
avoid loading on non-toshiba systems.
Documentation/ABI:
- ibm_rtl: The "What:" fields are incomplete
toshiba-wmi:
- Fix loading the driver on non Toshiba laptops
ideapad-laptop:
- Add another DMI entry for Yoga 900"
* tag 'platform-drivers-x86-v4.9-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
Documentation/ABI: ibm_rtl: The "What:" fields are incomplete
toshiba-wmi: Fix loading the driver on non Toshiba laptops
ideapad-laptop: Add another DMI entry for Yoga 900
|
|
Pull block fixes from Jens Axboe:
"Two small (really, one liners both of them!) fixes that should go into
this series:
- Request allocation error handling fix for nbd, from Christophe,
fixing a regression in this series.
- An oops fix for drbd. Not a regression in this series, but stable
material. From Richard"
* 'for-linus' of git://git.kernel.dk/linux-block:
drbd: Fix kernel_sendmsg() usage - potential NULL deref
nbd: Fix error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"AMD, radeon, i915, imx, msm and udl fixes:
- amdgpu/radeon have a number of power management regressions and
fixes along with some better error checking
- imx has a single regression fix
- udl has a single kmalloc instead of stack for usb control msg fix
- msm has some fixes for modesetting bugs and regressions
- i915 has a one fix for a Sandybridge regression along with some
others for DP audio.
They all seem pretty okay at this stage, we've got one MST fix I know
going through process for i915, but I expect it'll be next week"
* tag 'drm-fixes-for-v4.9-rc5' of git://people.freedesktop.org/~airlied/linux: (30 commits)
drm/udl: make control msg static const. (v2)
drm/amd/powerplay: implement get_clock_by_type for iceland.
drm/amd/powerplay/smu7: fix checks in smu7_get_evv_voltages (v2)
drm/amd/powerplay: update phm_get_voltage_evv_on_sclk for iceland
drm/amd/powerplay: propagate errors in phm_get_voltage_evv_on_sclk
drm/imx: disable planes before DC
drm/amd/powerplay: return false instead of -EINVAL
drm/amdgpu/powerplay/smu7: fix unintialized data usage
drm/amdgpu: fix crash in acp_hw_fini
drm/i915: Limit Valleyview and earlier to only using mappable scanout
drm/i915: Round tile chunks up for constructing partial VMAs
drm/i915/dp: Extend BDW DP audio workaround to GEN9 platforms
drm/i915/dp: BDW cdclk fix for DP audio
drm/i915/vlv: Prevent enabling hpd polling in late suspend
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/msm: Fix error handling crashes seen when VRAM allocation fails
drm/msm/mdp5: 8x16 actually has 8 mixer stages
drm/msm/mdp5: no scaling support on RGBn pipes for 8x16
drm/msm/mdp5: handle non-fullscreen base plane case
drm/msm: Set CLK_IGNORE_UNUSED flag for PLL clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix mmc card initialization for hosts not supporting HW busy
detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue"
* tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: Initialize the spinlock prior to using it
mmc: mmc: Use 500ms as the default generic CMD6 timeout
mmc: mmc_test: Fix "Commands during non-blocking write" tests
mmc: sdhci: Fix missing enhanced strobe setting during runtime resume
mmc: sdhci: Reset cmd and data circuits after tuning failure
mmc: sdhci: Fix unexpected data interrupt handling
mmc: sdhci: Fix CMD line reset interfering with ongoing data transfer
mmc: dw_mmc: add the "reset" as name of reset controller
Documentation: synopsys-dw-mshc: add binding for reset-names
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"All is about drivers, no core business going on.
- Fix a host of runtime problems with the Intel Cherryview driver:
suspend/resume needs to be marshalled properly, and strange effects
from BIOS interaction during suspend/resume need to be dealt with.
- A single bit was being set wrong in the Aspeed driver.
- Fix an iProc probe ordering fallout resulting from v4.9
refactorings for bus population.
- Do not specify a default trigger in the ST Micro cascaded GPIO IRQ
controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver, it turns out not
all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will eventually crash if
probed repeatedly, not good"
* tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl-aspeed-g5: Never set SCU90[6]
pinctrl: cherryview: Prevent possible interrupt storm on resume
pinctrl: cherryview: Serialize register access in suspend/resume
pinctrl: imx: reset group index on probe
pinctrl: stm32: move gpio irqs binding to optional
pinctrl: stm32: remove dependency with interrupt controller
pinctrl: st: don't specify default interrupt trigger
pinctrl: iproc: Fix iProc and NSP GPIO support
|
|
* pm-tools-fixes:
cpupower: Correct return type of cpu_power_is_cpu_online() in cpufreq-set
* pm-sleep-fixes:
PM / sleep: don't suspend parent when async child suspend_{noirq, late} fails
PM / sleep: fix device reference leak in test_suspend
|
|
* device-properties:
ACPI / platform: Add support for build-in properties
|
|
Merge fixes for -Wmaybe-uninitialized from Arnd Bergmann:
"It took a while for some patches to make it into mainline through
maintainer trees, but the 28-patch series is now reduced to 10, with
one tiny patch added at the end.
Aside from patches that are no longer required, I did these changes
compared to version 1:
- Dropped "iio: maxim_thermocouple: detect invalid storage size in
read()", which is currently in linux-next as commit 32cb7d27e65d.
This is the only remaining warning I see for a couple of corner
cases (kbuild bot reports it on blackfin, kernelci bot and arm-soc
bot both report it on arm64)
- Dropped "brcmfmac: avoid maybe-uninitialized warning in
brcmf_cfg80211_start_ap", which is currently in net/master merge
pending.
- Dropped two x86 patches, "x86: math-emu: possible uninitialized
variable use" and "x86: mark target address as output in 'insb'
asm" as they do not seem to trigger for a default build, and I got
no feedback on them. Both of these are ancient issues and seem
harmless, I will send them again to the x86 maintainers once the
rest is merged.
- Dropped "rbd: false-postive gcc-4.9 -Wmaybe-uninitialized" based on
feedback from Ilya Dryomov, who already has a different fix queued
up for v4.10. The kbuild bot reports this as a warning for xtensa.
- Replaced "crypto: aesni: avoid -Wmaybe-uninitialized warning" with
a simpler patch, this one always triggers but my first solution
would not be safe for linux-4.9 any more at this point. I'll follow
up with the larger patch as a cleanup for 4.10.
- Replaced "dib0700: fix nec repeat handling" with a better one,
contributed by Sean Young"
* -Wmaybe-uninitialized fixes:
Kbuild: enable -Wmaybe-uninitialized warnings by default
pcmcia: fix return value of soc_pcmcia_regulator_set
infiniband: shut up a maybe-uninitialized warning
crypto: aesni: shut up -Wmaybe-uninitialized warning
rc: print correct variable for z8f0811
dib0700: fix nec repeat handling
s390: pci: don't print uninitialized data for debugging
nios2: fix timer initcall return value
x86: apm: avoid uninitialized data
NFSv4.1: work around -Wmaybe-uninitialized warning
Kbuild: enable -Wmaybe-uninitialized warning for "make W=1"
|
|
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/stackdepot: export save/fetch stack for drivers
mm: kmemleak: scan .data.ro_after_init
memcg: prevent memcg caches to be both OFF_SLAB & OBJFREELIST_SLAB
coredump: fix unfreezable coredumping task
mm/filemap: don't allow partially uptodate page for pipes
mm/hugetlb: fix huge page reservation leak in private mapping error paths
ocfs2: fix not enough credit panic
Revert "console: don't prefer first registered if DT specifies stdout-path"
mm: hwpoison: fix thp split handling in memory_failure()
swapfile: fix memory corruption via malformed swapfile
mm/cma.c: check the max limit for cma allocation
scripts/bloat-o-meter: fix SIGPIPE
shmem: fix pageflags after swapping DMA32 object
mm, frontswap: make sure allocated frontswap map is assigned
mm: remove extra newline from allocation stall warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"Christoph's and Jan's aio fixes, fixup for generic_file_splice_read
(removal of pointless detritus that actually breaks it when used for
gfs2 ->splice_read()) and fixup for generic_file_read_iter()
interaction with ITER_PIPE destinations."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
splice: remove detritus from generic_file_splice_read()
mm/filemap: don't allow partially uptodate page for pipes
aio: fix freeze protection of aio writes
fs: remove aio_run_iocb
fs: remove the never implemented aio_fsync file operation
aio: hold an extra file reference over AIO read/write operations
|
|
Pull Ceph fixes from Ilya Dryomov:
"Ceph's ->read_iter() implementation is incompatible with the new
generic_file_splice_read() code that went into -rc1. Switch to the
less efficient default_file_splice_read() for now; the proper fix is
being held for 4.10.
We also have a fix for a 4.8 regression and a trival libceph fixup"
* tag 'ceph-for-4.9-rc5' of git://github.com/ceph/ceph-client:
libceph: initialize last_linger_id with a large integer
libceph: fix legacy layout decode with pool 0
ceph: use default file splice read callback
|
|
Pull NFS client bugfixes from Anna Schumaker:
"Most of these fix regressions in 4.9, and none are going to stable
this time around.
Bugfixes:
- Trim extra slashes in v4 nfs_paths to fix tools that use this
- Fix a -Wmaybe-uninitialized warnings
- Fix suspicious RCU usages
- Fix Oops when mounting multiple servers at once
- Suppress a false-positive pNFS error
- Fix a DMAR failure in NFS over RDMA"
* tag 'nfs-for-4.9-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
xprtrdma: Fix DMAR failure in frwr_op_map() after reconnect
fs/nfs: Fix used uninitialized warn in nfs4_slot_seqid_in_use()
NFS: Don't print a pNFS error if we aren't using pNFS
NFS: Ignore connections that have cl_rpcclient uninitialized
SUNRPC: Fix suspicious RCU usage
NFSv4.1: work around -Wmaybe-uninitialized warning
NFS: Trim extra slash in v4 nfs_path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fix from Dave Chinner:
"This is a fix for an unmount hang (regression) when the filesystem is
shutdown. It was supposed to go to you for -rc3, but I accidentally
tagged the commit prior to it in that pullreq.
Summary:
- fix for aborting deferred transactions on filesystem shutdown"
* tag 'xfs-fixes-for-linus-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: defer should abort intent items if the trans roll fails
|
|
Previously the warnings were added back at the W=1 level and above, this
now turns them on again by default, assuming that we have addressed all
warnings and again have a clean build for v4.10.
I found a number of new warnings in linux-next already and submitted
bugfixes for those. Hopefully they are caught by the 0day builder in
the future as soon as this patch is merged.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The newly introduced soc_pcmcia_regulator_set() function sometimes
returns without setting its return code, as shown by this warning:
drivers/pcmcia/soc_common.c: In function 'soc_pcmcia_regulator_set':
drivers/pcmcia/soc_common.c:112:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes it to propagate the regulator_disable() result instead.
Fixes: ac61b6001a63 ("pcmcia: soc_common: add support for Vcc and Vpp regulators")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some configurations produce this harmless warning when built with gcc
-Wmaybe-uninitialized:
infiniband/core/cma.c: In function 'cma_get_net_dev':
infiniband/core/cma.c:1242:12: warning: 'src_addr_storage.sin_addr.s_addr' may be used uninitialized in this function [-Wmaybe-uninitialized]
I previously reported this for the powerpc64 defconfig, but have now
reproduced the same thing for x86 as well, using gcc-5 or higher.
The code looks correct to me, and this change just rearranges it by
making sure we alway initialize the entire address structure to make the
warning disappear. My first approach added an initialization at the
time of the declaration, which Doug commented may be too costly, so I
hope this version doesn't add overhead.
Link: http://arm-soc.lixom.net/buildlogs/mainline/v4.7-rc6/buildall.powerpc.ppc64_defconfig.log.passed
Link: https://patchwork.kernel.org/patch/9212825/
Acked-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rfc4106 encrypy/decrypt helper functions cause an annoying
false-positive warning in allmodconfig if we turn on
-Wmaybe-uninitialized warnings again:
arch/x86/crypto/aesni-intel_glue.c: In function ‘helper_rfc4106_decrypt’:
include/linux/scatterlist.h:67:31: warning: ‘dst_sg_walk.sg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
The problem seems to be that the compiler doesn't track the state of the
'one_entry_in_sg' variable across the kernel_fpu_begin/kernel_fpu_end
section.
This takes the easy way out by adding a bogus initialization, which
should be harmless enough to get the patch into v4.9 so we can turn on
this warning again by default without producing useless output. A
follow-up patch for v4.10 rearranges the code to make the warning go
away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A recent rework accidentally left a debugging printk untouched while
changing the meaning of the variables, leading to an uninitialized
variable being printed:
drivers/media/i2c/ir-kbd-i2c.c: In function 'get_key_haup_common':
drivers/media/i2c/ir-kbd-i2c.c:62:2: error: 'toggle' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This prints the correct one instead, as we did before the patch.
Fixes: 00bb820755ed ("[media] rc: Hauppauge z8f0811 can decode RC6")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When receiving a nec repeat, ensure the correct scancode is repeated
rather than a random value from the stack. This removes the need for
the bogus uninitialized_var() and also fixes the warnings:
drivers/media/usb/dvb-usb/dib0700_core.c: In function ‘dib0700_rc_urb_completion’:
drivers/media/usb/dvb-usb/dib0700_core.c:679: warning: ‘protocol’ may be used uninitialized in this function
[sean addon: So after writing the patch and submitting it, I've bought the
hardware on ebay. Without this patch you get random scancodes
on nec repeats, which the patch indeed fixes.]
Signed-off-by: Sean Young <sean@mess.org>
Tested-by: Sean Young <sean@mess.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gcc correctly warns about an incorrect use of the 'pa' variable in case
we pass an empty scatterlist to __s390_dma_map_sg:
arch/s390/pci/pci_dma.c: In function '__s390_dma_map_sg':
arch/s390/pci/pci_dma.c:309:13: warning: 'pa' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds a bogus initialization to the function to sanitize the debug
output. I would have preferred a solution without the initialization,
but I only got the report from the kbuild bot after turning on the
warning again, and didn't manage to reproduce it myself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When called more than twice, the nios2_time_init() function return an
uninitialized value, as detected by gcc -Wmaybe-uninitialized
arch/nios2/kernel/time.c: warning: 'ret' may be used uninitialized in this function
This makes it return '0' here, matching the comment above the function.
Acked-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
apm_bios_call() can fail, and return a status in its argument structure.
If that status however is zero during a call from
apm_get_power_status(), we end up using data that may have never been
set, as reported by "gcc -Wmaybe-uninitialized":
arch/x86/kernel/apm_32.c: In function ‘apm’:
arch/x86/kernel/apm_32.c:1729:17: error: ‘bx’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/kernel/apm_32.c:1835:5: error: ‘cx’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/kernel/apm_32.c:1730:17: note: ‘cx’ was declared here
arch/x86/kernel/apm_32.c:1842:27: error: ‘dx’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/kernel/apm_32.c:1731:17: note: ‘dx’ was declared here
This changes the function to return "APM_NO_ERROR" here, which makes the
code more robust to broken BIOS versions, and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A bugfix introduced a harmless gcc warning in nfs4_slot_seqid_in_use if
we enable -Wmaybe-uninitialized again:
fs/nfs/nfs4session.c:203:54: error: 'cur_seq' may be used uninitialized in this function [-Werror=maybe-uninitialized]
gcc is not smart enough to conclude that the IS_ERR/PTR_ERR pair results
in a nonzero return value here. Using PTR_ERR_OR_ZERO() instead makes
this clear to the compiler.
Fixes: e09c978aae5b ("NFSv4.1: Fix Oopsable condition in server callback races")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Traditionally, we have always had warnings about uninitialized variables
enabled, as this is part of -Wall, and generally a good idea [1], but it
also always produced false positives, mainly because this is a variation
of the halting problem and provably impossible to get right in all cases
[2].
Various people have identified cases that are particularly bad for false
positives, and in commit e74fc973b6e5 ("Turn off -Wmaybe-uninitialized
when building with -Os"), I turned off the warning for any build that
was done with CC_OPTIMIZE_FOR_SIZE. This drastically reduced the number
of false positive warnings in the default build but unfortunately had
the side effect of turning the warning off completely in 'allmodconfig'
builds, which in turn led to a lot of warnings (both actual bugs, and
remaining false positives) to go in unnoticed.
With commit 877417e6ffb9 ("Kbuild: change CC_OPTIMIZE_FOR_SIZE
definition") enabled the warning again for allmodconfig builds in v4.7
and in v4.8-rc1, I had finally managed to address all warnings I get in
an ARM allmodconfig build and most other maybe-uninitialized warnings
for ARM randconfig builds.
However, commit 6e8d666e9253 ("Disable "maybe-uninitialized" warning
globally") was merged at the same time and disabled it completely for
all configurations, because of false-positive warnings on x86 that I had
not addressed until then. This caused a lot of actual bugs to get
merged into mainline, and I sent several dozen patches for these during
the v4.9 development cycle. Most of these are actual bugs, some are for
correct code that is safe because it is only called under external
constraints that make it impossible to run into the case that gcc sees,
and in a few cases gcc is just stupid and finds something that can
obviously never happen.
I have now done a few thousand randconfig builds on x86 and collected
all patches that I needed to address every single warning I got (I can
provide the combined patch for the other warnings if anyone is
interested), so I hope we can get the warning back and let people catch
the actual bugs earlier.
This reverts the change to disable the warning completely and for now
brings it back at the "make W=1" level, so we can get it merged into
mainline without introducing false positives. A follow-up patch enables
it on all levels unless some configuration option turns it off because
of false-positives.
Link: https://rusty.ozlabs.org/?p=232 [1]
Link: https://gcc.gnu.org/wiki/Better_Uninitialized_Warnings [2]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some drivers would like to record stacktraces in order to aide leak
tracing. As stackdepot already provides a facility for only storing the
unique traces, thereby reducing the memory required, export that
functionality for use by drivers.
The code was originally created for KASAN and moved under lib in commit
cd11016e5f521 ("mm, kasan: stackdepot implementation. Enable stackdepot
for SLAB") so that it could be shared with mm/. In turn, we want to
share it now with drivers.
Link: http://lkml.kernel.org/r/20161108133209.22704-1-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Limit the number of kmemleak false positives by including
.data.ro_after_init in memory scanning. To achieve this we need to add
symbols for start and end of the section to the linker scripts.
The problem was been uncovered by commit 56989f6d8568 ("genetlink: mark
families as __ro_after_init").
Link: http://lkml.kernel.org/r/1478274173-15218-1-git-send-email-jakub.kicinski@netronome.com
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While testing OBJFREELIST_SLAB integration with pagealloc, we found a
bug where kmem_cache(sys) would be created with both CFLGS_OFF_SLAB &
CFLGS_OBJFREELIST_SLAB. When it happened, critical allocations needed
for loading drivers or creating new caches will fail.
The original kmem_cache is created early making OFF_SLAB not possible.
When kmem_cache(sys) is created, OFF_SLAB is possible and if pagealloc
is enabled it will try to enable it first under certain conditions.
Given kmem_cache(sys) reuses the original flag, you can have both flags
at the same time resulting in allocation failures and odd behaviors.
This fix discards allocator specific flags from memcg before calling
create_cache.
The bug exists since 4.6-rc1 and affects testing debug pagealloc
configurations.
Fixes: b03a017bebc4 ("mm/slab: introduce new slab management type, OBJFREELIST_SLAB")
Link: http://lkml.kernel.org/r/1478553075-120242-1-git-send-email-thgarnie@google.com
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Tested-by: Thomas Garnier <thgarnie@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It could be not possible to freeze coredumping task when it waits for
'core_state->startup' completion, because threads are frozen in
get_signal() before they got a chance to complete 'core_state->startup'.
Inability to freeze a task during suspend will cause suspend to fail.
Also CRIU uses cgroup freezer during dump operation. So with an
unfreezable task the CRIU dump will fail because it waits for a
transition from 'FREEZING' to 'FROZEN' state which will never happen.
Use freezer_do_not_count() to tell freezer to ignore coredumping task
while it waits for core_state->startup completion.
Link: http://lkml.kernel.org/r/1475225434-3753-1-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Starting from 4.9-rc1 kernel, I started noticing some test failures of
sendfile(2) and splice(2) (sendfile0N and splice01 from LTP) when
testing on sub-page block size filesystems (tested both XFS and ext4),
these syscalls start to return EIO in the tests. e.g.
sendfile02 1 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 26, got: -1
sendfile02 2 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 24, got: -1
sendfile02 3 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 22, got: -1
sendfile02 4 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 20, got: -1
This is because that in sub-page block size cases, we don't need the
whole page to be uptodate, only the part we care about is uptodate is OK
(if fs has ->is_partially_uptodate defined).
But page_cache_pipe_buf_confirm() doesn't have the ability to check the
partially-uptodate case, it needs the whole page to be uptodate. So it
returns EIO in this case.
This is a regression introduced by commit 82c156f85384 ("switch
generic_file_splice_read() to use of ->read_iter()"). Prior to the
change, generic_file_splice_read() doesn't allow partially-uptodate page
either, so it worked fine.
Fix it by skipping the partially-uptodate check if we're working on a
pipe in do_generic_file_read(), so we read the whole page from disk as
long as the page is not uptodate.
I think the other way to fix it is to add the ability to check & allow
partially-uptodate page to page_cache_pipe_buf_confirm(), but that is
much harder to do and seems gain little.
Link: http://lkml.kernel.org/r/1477986187-12717-1-git-send-email-guaneryu@gmail.com
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Error paths in hugetlb_cow() and hugetlb_no_page() may free a newly
allocated huge page.
If a reservation was associated with the huge page, alloc_huge_page()
consumed the reservation while allocating. When the newly allocated
page is freed in free_huge_page(), it will increment the global
reservation count. However, the reservation entry in the reserve map
will remain.
This is not an issue for shared mappings as the entry in the reserve map
indicates a reservation exists. But, an entry in a private mapping
reserve map indicates the reservation was consumed and no longer exists.
This results in an inconsistency between the reserve map and the global
reservation count. This 'leaks' a reserved huge page.
Create a new routine restore_reserve_on_error() to restore the reserve
entry in these specific error paths. This routine makes use of a new
function vma_add_reservation() which will add a reserve entry for a
specific address/page.
In general, these error paths were rarely (if ever) taken on most
architectures. However, powerpc contained arch specific code that that
resulted in an extra fault and execution of these error paths on all
private mappings.
Fixes: 67961f9db8c4 ("mm/hugetlb: fix huge page reserve accounting for private mappings)
Link: http://lkml.kernel.org/r/1476933077-23091-2-git-send-email-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Kirill A . Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following panic was caught when run ocfs2 disconfig single test
(block size 512 and cluster size 8192). ocfs2_journal_dirty() return
-ENOSPC, that means credits were used up.
The total credit should include 3 times of "num_dx_leaves" from
ocfs2_dx_dir_rebalance(), because 2 times will be consumed in
ocfs2_dx_dir_transfer_leaf() and 1 time will be consumed in
ocfs2_dx_dir_new_cluster() -> __ocfs2_dx_dir_new_cluster() ->
ocfs2_dx_dir_format_cluster(). But only two times is included in
ocfs2_dx_dir_rebalance_credits(), fix it.
This can cause read-only fs(v4.1+) or panic for mainline linux depending
on mount option.
------------[ cut here ]------------
kernel BUG at fs/ocfs2/journal.c:775!
invalid opcode: 0000 [#1] SMP
Modules linked in: ocfs2 nfsd lockd grace nfs_acl auth_rpcgss sunrpc autofs4 ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs sd_mod sg ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables be2iscsi iscsi_boot_sysfs bnx2i cnic uio cxgb4i cxgb4 cxgb3i libcxgbi cxgb3 mdio ib_iser rdma_cm ib_cm iw_cm ib_sa ib_mad ib_core ib_addr ipv6 iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ppdev xen_kbdfront xen_netfront fb_sys_fops sysimgblt sysfillrect syscopyarea parport_pc parport acpi_cpufreq i2c_piix4 i2c_core pcspkr ext4 jbd2 mbcache xen_blkfront floppy pata_acpi ata_generic ata_piix dm_mirror dm_region_hash dm_log dm_mod
CPU: 2 PID: 10601 Comm: dd Not tainted 4.1.12-71.el6uek.bug24939243.x86_64 #2
Hardware name: Xen HVM domU, BIOS 4.4.4OVM 02/11/2016
task: ffff8800b6de6200 ti: ffff8800a7d48000 task.ti: ffff8800a7d48000
RIP: ocfs2_journal_dirty+0xa7/0xb0 [ocfs2]
RSP: 0018:ffff8800a7d4b6d8 EFLAGS: 00010286
RAX: 00000000ffffffe4 RBX: 00000000814d0a9c RCX: 00000000000004f9
RDX: ffffffffa008e990 RSI: ffffffffa008f1ee RDI: ffff8800622b6460
RBP: ffff8800a7d4b6f8 R08: ffffffffa008f288 R09: ffff8800622b6460
R10: 0000000000000000 R11: 0000000000000282 R12: 0000000002c8421e
R13: ffff88006d0cad00 R14: ffff880092beef60 R15: 0000000000000070
FS: 00007f9b83e92700(0000) GS:ffff8800be880000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb2c0d1a000 CR3: 0000000008f80000 CR4: 00000000000406e0
Call Trace:
ocfs2_dx_dir_transfer_leaf+0x159/0x1a0 [ocfs2]
ocfs2_dx_dir_rebalance+0xd9b/0xea0 [ocfs2]
ocfs2_find_dir_space_dx+0xd3/0x300 [ocfs2]
ocfs2_prepare_dx_dir_for_insert+0x219/0x450 [ocfs2]
ocfs2_prepare_dir_for_insert+0x1d6/0x580 [ocfs2]
ocfs2_mknod+0x5a2/0x1400 [ocfs2]
ocfs2_create+0x73/0x180 [ocfs2]
vfs_create+0xd8/0x100
lookup_open+0x185/0x1c0
do_last+0x36d/0x780
path_openat+0x92/0x470
do_filp_open+0x4a/0xa0
do_sys_open+0x11a/0x230
SyS_open+0x1e/0x20
system_call_fastpath+0x12/0x71
Code: 1d 3f 29 09 00 48 85 db 74 1f 48 8b 03 0f 1f 80 00 00 00 00 48 8b 7b 08 48 83 c3 10 4c 89 e6 ff d0 48 8b 03 48 85 c0 75 eb eb 90 <0f> 0b eb fe 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 41 54
RIP ocfs2_journal_dirty+0xa7/0xb0 [ocfs2]
---[ end trace 91ac5312a6ee1288 ]---
Kernel panic - not syncing: Fatal exception
Kernel Offset: disabled
Link: http://lkml.kernel.org/r/1478248135-31963-1-git-send-email-junxiao.bi@oracle.com
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 05fd007e4629 ("console: don't prefer first
registered if DT specifies stdout-path").
The reverted commit changes existing behavior on which many ARM boards
rely. Many ARM small-board-computers, like e.g. the Raspberry Pi have
both a video output and a serial console. Depending on whether the user
is using the device as a more regular computer; or as a headless device
we need to have the console on either one or the other.
Many users rely on the kernel behavior of the console being present on
both outputs, before the reverted commit the console setup with no
console= kernel arguments on an ARM board which sets stdout-path in dt
would look like this:
[root@localhost ~]# cat /proc/consoles
ttyS0 -W- (EC p a) 4:64
tty0 -WU (E p ) 4:1
Where as after the reverted commit, it looks like this:
[root@localhost ~]# cat /proc/consoles
ttyS0 -W- (EC p a) 4:64
This commit reverts commit 05fd007e4629 ("console: don't prefer first
registered if DT specifies stdout-path") restoring the original
behavior.
Fixes: 05fd007e4629 ("console: don't prefer first registered if DT specifies stdout-path")
Link: http://lkml.kernel.org/r/20161104121135.4780-2-hdegoede@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When memory_failure() runs on a thp tail page after pmd is split, we
trigger the following VM_BUG_ON_PAGE():
page:ffffd7cd819b0040 count:0 mapcount:0 mapping: (null) index:0x1
flags: 0x1fffc000400000(hwpoison)
page dumped because: VM_BUG_ON_PAGE(!page_count(p))
------------[ cut here ]------------
kernel BUG at /src/linux-dev/mm/memory-failure.c:1132!
memory_failure() passed refcount and page lock from tail page to head
page, which is not needed because we can pass any subpage to
split_huge_page().
Fixes: 61f5d698cc97 ("mm: re-enable THP")
Link: http://lkml.kernel.org/r/1477961577-7183-1-git-send-email-n-horiguchi@ah.jp.nec.com
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
