| Age | Commit message (Collapse) | Author |
|---|
|
Added variables to separate the fine tuned timeout values for
connection destroy and context destroy for both 1g and 10g devices.
v2: Extended the 5771X disconnect timeout from 10s to 20s as the firmware
has a retransmission timeout of 16s. This fixes one of the iscsi_endpoint
leak issues when the target is slow or non-responsive to our TCP FIN.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
For cases where the iSCSI disconnection procedure times out due to
the iSCSI daemon being slow or unresponsive, the bnx2i_stop routine
will now perform hardware cleanup via bnx2i_hw_ep_disconnect on all
active endpoints so that subsequent operations will perform properly.
Also moved the mutex locks inside ep_connect and ep_disconnect so
that proper exclusivity can resolve simultaneous calls to the
ep_disconnect routine.
v2: Removed the unnecessary read lock in the bnx2i_stop
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This introduces a new active linklist which would link up all active
bnx2i_endpoints. This will be used by subsequent patches that
follows.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch introduces a new bnx2i_hw_ep_disconnect routine which
contains all chip related disconnect and clean up procedure of
iSCSI offload connections. This separation is intended as a
preparation for the subsequent bnx2i_stop patch.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
map_region and unmap_region could access to invalid memory area since
they don't check the size boundary.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The value used to change the endian representation on the new adapters has
changed. This patch updates that value.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch allows the driver to recognize a new Obsidian-E based adapter that
uses a new subsystem ID.
This patch also fixes a few tab/space problems.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Stanse found that in mvs_abort_task, mvi_dev is dereferenced earlier
than tested for being NULL. Move the assignment below the test.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Printing Doorbell register in a case of hard reset and timeout
should be useful for figuring out the state of the system.
Signed-off-by: Kei Tokunaga <tokunaga.keiich@jp.fujitsu.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The below patch fixes a warning message generated by gcc 4.6.0
CC drivers/scsi/hosts.o
drivers/scsi/hosts.c: In function 'scsi_host_alloc':
drivers/scsi/hosts.c:328:6: warning: variable 'rval' set but not used
Fix this by removing the rval but placing a printk warning where it
would have been set.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
If the user accidentally changes LUN mappings or it occurs
due to a bug, then it can cause data corruption that can take
months and months to track down. This patch adds a log
message when getting REPORT_LUNS_DATA_CHANGED and it adds
a generic message for other Unit Attentions with asc == 0x3f.
We are working on adding support for handling of these errors,
but I think until then we should at least log a message so
tracking down problems as a result of one of these changes
is a little easier.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch fixes mptsas disk hot-removal processing. The
hot-removal processing doesn't complete because of this condition.
drivers/message/fusion/mptsas.c:
mptsas_taskmgmt_complete()
if ((mptsas_find_vtarget(ioc, channel, id)) && !ioc->fw_events_off)
mptsas_queue_device_delete(...);
mptsas_queue_device_delete(), which must be called for
hot-removal, never gets called because mptsas_find_vtarget()
always returns 0 here. At that time, the vtarget has already
been freed in mptsas_target_destroy(), and also the scsi_device
has been marked as SDEV_DEL.
As a result of the issue, port deletion functions won't get
called and the device ends up being in an incomplete state.
(Some data structures and sysfs entries, which should be
removed in hot-removal, remain.) One side effect of this is
that a hot-addition of the device (bringing the device back
on) fails.
This patch just removes mptsas_find_vtarget() from the if-state
condition.
Signed-off-by: Kei Tokunaga <tokunaga.keiich@jp.fujitsu.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The 64 bit chip used in new adapters does not properly support the BIST register
in PCI config space. This patch implements an alternative MMIO write reset
method.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
1. To support Type C RAID controller, ACB_ADAPTER_TYPE_C, i.e. PCI device
ID: 0x1880.
Signed-off-by: Nick Cheng< nick.cheng@areca.com.tw >
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
we also need to clean up and free the cdev.
Reported-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Bump driver version
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
If we encounter an error when sending a management datagram (i.e. non
SCSI command, such as virtual adapter initialization command), we
end up incrementing the request_limit, even though we don't decrement
it for these commands. Fix this up by doing this increment in
the error path for SRP commands only.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fixes a deadlock that can occur if we hit a command timeout
during the virtual adapter initialization. The event done
functions are written with the assumption that no locks are held,
however, when purging requests this is not true. Fix up the
purge function to drop the lock so that the done function
is not called with the lock held, which can cause a deadlock.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This fixes a softlockup seen on resume. During resume, the CRQ
must be reenabled. However, the H_ENABLE_CRQ hcall used to do
this may return H_BUSY or H_LONG_BUSY. When this happens, the
caller is expected to retry later. This patch changes a simple
loop, which was causing the softlockup, to a loop at task level
which sleeps between retries rather than simply spinning.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Bump driver version.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Adds support for fc_block_scsi_eh to block the EH handlers if
the target device is in the blocked state to ensure we don't
take devices offline.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This fixes a softlockup seen on resume. During resume, the CRQ
must be reenabled. However, the H_ENABLE_CRQ hcall used to do
this may return H_BUSY or H_LONG_BUSY. When this happens, the
caller is expected to retry later. Normally the H_ENABLE_CRQ
succeeds relatively soon. However, we have seen cases where
this can take long enough to see softlockup warnings.
This patch changes a simple loop, which was causing the
softlockup, to a loop at task level which sleeps between
retries rather than simply spinning.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
In mpt_detach, call to pci_set_drvdata is redundant because it
has already been called in mpt_adapter_disable. In mpt_attach,
ioc->pcidev is set to pdev two times.
Signed-off-by: Bandan Das <bandan.das@stratus.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Upgrade driver version to 3.4.16
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added missing part which will reset ioc_reset_in_progress before returning from SoftResetHandler.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Issue: SATA hotplug does not work sometimes.
At the time of ADD device/ADD phys disk, drive may fail to add SATA device
due to temporary SAS Address for SATA device generated by firmware. Final
SAS address for SATA driver will be generated only after disk spinup is
done. This may take some times for slow spining SATA drives.
At phy link up driver gets attached device sas address and stores into
phyinfo. At the time of ADD event driver will read sas device page0 using
channel and FW ID provided in ADD Device event. Here in case of SATA drives,
driver will see miss match in phyinfo->sas_address and latest sas address
read from SAS DEVICE PAGE0 and eventually device won't be added to OS.
Fix:
When Driver read SAS DEVICE PAGE0, it can identify Device type looking at
device_info. If device is SATA drive and sas address mismatch happens,
Driver will do same stuffs which happened at the time of LINK UP to get
correct piece of information from Pages. ( Find parent device and refresh
parent device phys either HBA refresh/Exp refresh)
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Issue:
target reset will be queued to driver's internal queue to get schedule
later. When driver add target into internal target_reset queue we will block IOs
on those target using scsi midlayer API. Now due to some cause driver is not
executing those target_reset list and it is always in block state.
Changes:
now we are clearing target_reset queue from all other Callback context
instead of only DeviceReset context.Now wherever driver is clearing
taskmgmt_in_progress flag it is considering target_reset queue cleanup
also.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
to OS
Added sanity check before treating any device is a valid device.
It is possible that firmware can have device page0 in its table, but that
devicemay not be available in topology. Device will be available in topology
only if there is Bus Target mapping is done in firmware. Driver will always
check B_T mapping of firmware before reporting device to upper layer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
device missing delay is 8 bit value in io unit pg1. Making correct variable
declaration for device_missing_delay.
The driver is storing the calculated device missing delay in IOC structure
as a u8 instead of a u16. It needs to be a u16 if the delay is > 255.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Changed the return value for Nexus Loss IOs to be DID_TRANSPORT_DISRUPTED.
What this will allow is the multi-path driver to delay the fail over
process. They would like the path to keep up as long as the nexus loss
Loginfo is return from firmware. With DID_BUS_BUSY the path fails over
immediately.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
fw_events_off is flag checking for driver to do Event handling or not.
Normally it should be OFF at the time of initialization. Only enable it at
the time of INTR enable of device first time. This will always occur only
after resource allocation.
ioc->fw_events_off = 1 is set in mpt_attach()
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Version upgrade patch
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
local reference.
Current driver is not clearing the per device tm_busy flag
following the Task Mangement request completion from the IOCTL path.
When this flag is set, the IO queues are frozen. The reason the flag
didn't get cleared is becuase the driver is referencing
memory associated to the mpi request following the completion, when
the memory had been reallocated for a new request. When the memory
was reallocated, the driver didn't clear the flag becuase it was
expecting a task managment reqeust, and the reallocated request was
for SCSI_IO. To fix the problem the driver needs to have a cached
backup copy of the original reqeust.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
(1) driver was not setting the sense data size prior to sending SCSI_IO,
resulting in the 0x31190000 loginfo
(2) The driver needs to copy the sense data to local buffer prior
to releasing the request message frame. If not, the sense buffer gets
overwritten by the next SCSI_IO request.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Adding additional messages to the error escallation callbacks which
displays the wwid, sas address, handle, phy number, enclosure logical id,
and slot. In the same eh callbacks, routines, the printks were converted
to sdev_printks, which displays the bus target mapping. These additional
modifications help better identify the device which is in recovery.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
ISSUE DESCRIPTION:
This test case involves creating two RAID1 volumes, then
simultaneiously issue host reset and pull all the drives associated to
the 1st raid volume. The observed behavour is the physical drives are
removed, however the volume remains. The expected behavour is the
volume as well as physical drives should be removed from OS.
FIX:
Add support in the post host reset device scan logic for raid volumes
where the driver will have an additional check for responding raid
volume where the status should be either online, optimal, or degraded.
So for voluemes that have a status of missing or failed, the driver
will mark them for deletion.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
In the driver mpt2sas_base_attach subroutine, we need to add
support to return the proper error code when there are memory allocation
failures, e.g. returning -ENOMEM.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Actual problem :
Driver may receiving the top level expander
removal event prior to all the individual PD removal events, hence the
driver is breaking down all the PDs in advanced to the actaul PD UNHIDE
event. Driver sends multiple
Target Resets to the same volume handle for each individual PD removal.
FIX DESCRIPTION:
To fix this issue, the entire PD device handshake protocal has to be
moved to interrupt context so the breakdown occurs immediately after the
actual UNHIDE event arrives. The driver will only issue one Target Reset to
the volume handle, occurring after the FAILED or MISSING volume status
event arrives from interrupt context. For the PD UNHIDE event, the driver
will issue target resets to the PD handles, followed by OP_REMOVE. The
driver will set the "deteleted" flag during interrupt context. A "pd_handle"
bitmask was introduced so the driver has a list of known pds during entire
life of the PD; this replaces the "hidden_raid_component" flag handle in
the sas_device object. Each bit in the bitmask represents a device handle.
The bit in the bitmask would be toggled ON/OFF when the HIDE/UNHIDE
events arrive; also this pd_handle bitmask would bould be refreshed
across host resets.
Here we kept older behavior of sending target reset to volume when there is
a single drive pull, wait for the reply, then send target resets
to the PDs. We kept this behavior so the driver will
behave the same for older versions of firmware.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add support to display additional debug info for SCSI_IO and
RAID_SCSI_IO_PASSTHROUGH sent from the normal entry queued entry
point, as well as internal generated commands, and IOCTLS. The
additional debug info included the phy number, as well as the
sas address, enclosure logical id, and slot number. This debug info
has to be enabled thru the logging_level command line option, by
default this will not be displayed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Converting print level from MPT2SAS_DEBUG_FMT to MPT2SAS_INFO_FMT.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added support so the diag ring buffer can be pulled via sysfs
Added three new shost attributes: host_trace_buffer,
host_trace_buffer_enable, and host_trace_buffer_size. The
host_trace_buffer_enable attribute is used to either post or release
the trace buffers. The host_trace_buffer_size attribute contains
the size of the trace buffer. The host_trace_buffer atttribute contains
a maximum 4KB window of the buffer. In order to read the entire host buffer,
you will need to write the offset to host_trace_buffer prior to reading
it. release the host buffer, then write the entire host buffer contents to
a file.
In addition to this enhancement, we moved the automatic posting of host buffers
at driver load time to be called prior to port_enable, instead of after.
That way discovery is available in the host buffer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Updating MPI header version N.
Removed mpi_history.txt.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added a new sysfs shost attribute called ioc_reset_count. This will
keep count of host resets (both diagnostic and message unit).
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added support to send link resets, hard resets, enable/disable phys, and
changing link rates for for expanders. This will be exported to
attributes within the sas transport layer. A new wrapper function was
added for sending SMP passthru to expanders for phy control.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added support to retrieve the invalid_dword_count,
running_disparity_error_count, loss_of_dword_sync_count, and
phy_reset_problem_count for expanders. This will be exported to
attributes within the sas transport layer. A new wrapper function was
added for sending SMP passthru to retrieve the expander phy error log.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
is added.
Added command line option called disable_discovery. When enabled
on the command line, the driver will not send a port_enable when loaded
for the first time. If port_enable is not called, then there is
no discovery of devices, as well as the sas topology. Then later if one
desires to invoke discovery, then they will need to issue a diagnostic reset.
A diagnostic reset can be issued various ways. One of the way is throught
sysfs.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Driver should not allow multiple host reset when already host reset is in
progress. It is possible that host reset was sent by scsi mid layer while there was already an host reset active,
either issued via IOCTL interface or internaly, like a config page timeout.
Since there was a host reset active, the driver would return a FAILED response
to the scsi mid layer. The solution is make sure pending host resets will
wait for the active host reset to complete before returning control
back up the call stack.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
_transpor_get_enclosure_identifier.
Enclosure_identifier not being returned by mpt2sas
The driver exports callback function to the sas transport layer
for obtaining the enclosure logical id. This function is called
_transport_get_enclosure_identifier. The driver was searching
the wrong list for the enclosure_identifier. The driver should be
searching the sas device list instead of enclosure list. The
sas address that is passed to the driver is for the end device, not
enclosure.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Zero out the reserved or un-used CPL message fields to prevent any garbage
value.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Some controllers might try to tell us they support 0 commands
in performant mode. This is a lie told by buggy firmware.
We have to be wary of this lest we try to allocate a negative
number of command blocks, which will be treated as unsigned,
and get an out of memory condition.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
