summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-11-20Merge branch 'r8169-smaller-improvements-to-firmware-handling'David S. Miller
Heiner Kallweit says: ==================== r8169: smaller improvements to firmware handling This series includes few smaller improvements to firmware handling. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20r8169: add check for PHY_MDIO_CHG to rtl_nic_fw_data_okHeiner Kallweit
Only values 0 and 1 are currently defined as parameters for PHY_MDIO_CHG. Instead of silently ignoring unknown values and misinterpreting the firmware code let's explicitly check. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20r8169: use macro FIELD_SIZEOF in definition of FW_OPCODE_SIZEHeiner Kallweit
Using macro FIELD_SIZEOF makes this define easier understandable. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20r8169: change mdelay to msleep in rtl_fw_write_firmwareHeiner Kallweit
We're not in atomic context here, therefore switch to msleep. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ipconfig: Wait for deferred device probesThomas Bogendoerfer
If network device drives are using deferred probing, it was possible that waiting for devices to show up in ipconfig was already over, when the device eventually showed up. By calling wait_for_device_probe() we now make sure deferred probing is done before checking for available devices. Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20vsock/vmci: make vmci_vsock_cb_host_called staticMao Wenan
When using make C=2 drivers/misc/vmw_vmci/vmci_driver.o to compile, below warning can be seen: drivers/misc/vmw_vmci/vmci_driver.c:33:6: warning: symbol 'vmci_vsock_cb_host_called' was not declared. Should it be static? This patch make symbol vmci_vsock_cb_host_called static. Fixes: b1bba80a4376 ("vsock/vmci: register vmci_transport only when VMCI guest/host are active") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Mao Wenan <maowenan@huawei.com> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20Merge branch 'page_pool-DMA-sync'David S. Miller
Lorenzo Bianconi says: ==================== add DMA-sync-for-device capability to page_pool API Introduce the possibility to sync DMA memory for device in the page_pool API. This feature allows to sync proper DMA size and not always full buffer (dma_sync_single_for_device can be very costly). Please note DMA-sync-for-CPU is still device driver responsibility. Relying on page_pool DMA sync mvneta driver improves XDP_DROP pps of about 170Kpps: - XDP_DROP DMA sync managed by mvneta driver: ~420Kpps - XDP_DROP DMA sync managed by page_pool API: ~585Kpps Do not change naming convention for the moment since the changes will hit other drivers as well. I will address it in another series. Changes since v4: - do not allow the driver to set max_len to 0 - convert PP_FLAG_DMA_MAP/PP_FLAG_DMA_SYNC_DEV to BIT() macro Changes since v3: - move dma_sync_for_device before putting the page in ptr_ring in __page_pool_recycle_into_ring since ptr_ring can be consumed concurrently. Simplify the code moving dma_sync_for_device before running __page_pool_recycle_direct/__page_pool_recycle_into_ring Changes since v2: - rely on PP_FLAG_DMA_SYNC_DEV flag instead of dma_sync Changes since v1: - rename sync in dma_sync - set dma_sync_size to 0xFFFFFFFF in page_pool_recycle_direct and page_pool_put_page routines - Improve documentation ==================== Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: mvneta: get rid of huge dma sync in mvneta_rx_refillLorenzo Bianconi
Get rid of costly dma_sync_single_for_device in mvneta_rx_refill since now the driver can let page_pool API to manage needed DMA sync with a proper size. - XDP_DROP DMA sync managed by mvneta driver: ~420Kpps - XDP_DROP DMA sync managed by page_pool API: ~585Kpps Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: page_pool: add the possibility to sync DMA memory for deviceLorenzo Bianconi
Introduce the following parameters in order to add the possibility to sync DMA memory for device before putting allocated pages in the page_pool caches: - PP_FLAG_DMA_SYNC_DEV: if set in page_pool_params flags, all pages that the driver gets from page_pool will be DMA-synced-for-device according to the length provided by the device driver. Please note DMA-sync-for-CPU is still device driver responsibility - offset: DMA address offset where the DMA engine starts copying rx data - max_len: maximum DMA memory size page_pool is allowed to flush. This is currently used in __page_pool_alloc_pages_slow routine when pages are allocated from page allocator These parameters are supposed to be set by device drivers. This optimization reduces the length of the DMA-sync-for-device. The optimization is valid because pages are initially DMA-synced-for-device as defined via max_len. At RX time, the driver will perform a DMA-sync-for-CPU on the memory for the packet length. What is important is the memory occupied by packet payload, because this is the area CPU is allowed to read and modify. As we don't track cache-lines written into by the CPU, simply use the packet payload length as dma_sync_size at page_pool recycle time. This also take into account any tail-extend. Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: mvneta: rely on page_pool_recycle_direct in mvneta_run_xdpLorenzo Bianconi
Rely on page_pool_recycle_direct and not on xdp_return_buff in mvneta_run_xdp. This is a preliminary patch to limit the dma sync len to the one strictly necessary Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: sched: pie: enable timestamp based delay calculationGautam Ramakrishnan
RFC 8033 suggests an alternative approach to calculate the queue delay in PIE by using a timestamp on every enqueued packet. This patch adds an implementation of that approach and sets it as the default method to calculate queue delay. The previous method (based on Little's law) to calculate queue delay is set as optional. Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Acked-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20isdn: Fix Kconfig indentationKrzysztof Kozlowski
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20nfc: Fix Kconfig indentationKrzysztof Kozlowski
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20Merge branch 'cxgb4-add-TC-MATCHALL-classifier-offload'David S. Miller
Rahul Lakkireddy says: ==================== cxgb4: add TC-MATCHALL classifier offload This series of patches add support to offload TC-MATCHALL classifier to hardware to classify all outgoing and incoming traffic on the underlying port. Only 1 egress and 1 ingress rule each can be offloaded on the underlying port. Patch 1 adds support for TC-MATCHALL classifier offload on the egress side. TC-POLICE is the only action that can be offloaded on the egress side and is used to rate limit all outgoing traffic to specified max rate. Patch 2 adds logic to reject the current rule offload if its priority conflicts with existing rules in the TCAM. Patch 3 adds support for TC-MATCHALL classifier offload on the ingress side. The same set of actions supported by existing TC-FLOWER classifier offload can be applied on all the incoming traffic. v5: - Fixed commit message and comment to include comparison for equal priority in patch 2. v4: - Removed check in patch 1 to reject police offload if prio is not 1. - Moved TC_SETUP_BLOCK code to separate function in patch 1. - Added logic to ensure the prio passed by TC doesn't conflict with other rules in TCAM in patch 2. - Higher index has lower priority than lower index in TCAM. So, rework cxgb4_get_free_ftid() to search free index from end of TCAM in descending order in patch 2. - Added check to ensure the matchall rule's prio doesn't conflict with other rules in TCAM in patch 3. - Added logic to fill default mask for VIID, if none has been provided, to prevent conflict with duplicate VIID rules in patch 3. - Used existing variables in private structure to fill VIID info, instead of extracting the info manually in patch 3. v3: - Added check in patch 1 to reject police offload if prio is not 1. - Assign block_shared variable only for TC_SETUP_BLOCK in patch 1. v2: - Added check to reject flow block sharing for policers in patch 1. - Removed logic to fetch free index from end of TCAM in patch 2. Must maintain the same ordering as in kernel. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20cxgb4: add TC-MATCHALL classifier ingress offloadRahul Lakkireddy
Add TC-MATCHALL classifier ingress offload support. The same actions supported by existing TC-FLOWER offload can be applied to all incoming traffic on the underlying interface. Ensure the rule priority doesn't conflict with existing rules in the TCAM. Only 1 ingress matchall rule can be active at a time on the underlying interface. v5: - No change. v4: - Added check to ensure the matchall rule's prio doesn't conflict with other rules in TCAM. - Added logic to fill default mask for VIID, if none has been provided, to prevent conflict with duplicate VIID rules. - Used existing variables in private structure to fill VIID info, instead of extracting the info manually. v3: - No change. v2: - Removed logic to fetch free index from end of TCAM. Must maintain same ordering as in kernel. Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20cxgb4: check rule prio conflicts before offloadRahul Lakkireddy
Only offload rule if it satisfies both of the following conditions: 1. The immediate previous rule has priority <= current rule's priority. 2. The immediate next rule has priority >= current rule's priority. Also rework free entry fetch logic to search from end of TCAM, instead of beginning, because higher indices have lower priority than lower indices. This is similar to how TC auto generates priority values. v5: - Fixed commit message and comment to include comparison for equal priority. v4: - Patch added in this version. Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20cxgb4: add TC-MATCHALL classifier egress offloadRahul Lakkireddy
Add TC-MATCHALL classifier offload with TC-POLICE action applied for all outgoing traffic on the underlying interface. Split flow block offload to support both egress and ingress classification. For example, to rate limit all outgoing traffic to 1 Gbps: $ tc qdisc add dev enp2s0f4 clsact $ tc filter add dev enp2s0f4 egress matchall skip_sw \ action police rate 1Gbit burst 8Kbit Note that skip_sw is important. Otherwise, both stack and hardware will end up doing policing. Policing can't be shared across flow blocks. Only 1 egress matchall rule can be active at a time on the underlying interface. v5: - No change. v4: - Removed check to reject police offload if prio is not 1. - Moved TC_SETUP_BLOCK code to separate function. v3: - Added check to reject police offload if prio is not 1. - Assign block_shared variable only for TC_SETUP_BLOCK. v2: - Added check to reject flow block sharing for policers. Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20Merge branch 'page_pool-API-for-numa-node-change-handling'David S. Miller
Saeed Mahameed says: ==================== page_pool: API for numa node change handling This series extends page pool API to allow page pool consumers to update page pool numa node on the fly. This is required since on some systems, rx rings irqs can migrate between numa nodes, due to irq balancer or user defined scripts, current page pool has no way to know of such migration and will keep allocating and holding on to pages from a wrong numa node, which is bad for the consumer performance. 1) Add API to update numa node id of the page pool Consumers will call this API to update the page pool numa node id. 2) Don't recycle non-reusable pages: Page pool will check upon page return whether a page is suitable for recycling or not. 2.1) when it belongs to a different num node. 2.2) when it was allocated under memory pressure. 3) mlx5 will use the new API to update page pool numa id on demand. The series is a joint work between me and Jonathan, we tested it and it proved itself worthy to avoid page allocator bottlenecks and improve packet rate and cpu utilization significantly for the described scenarios above. Performance testing: XDP drop/tx rate and TCP single/multi stream, on mlx5 driver while migrating rx ring irq from close to far numa: mlx5 internal page cache was locally disabled to get pure page pool results. CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G) XDP Drop/TX single core: NUMA | XDP | Before | After --------------------------------------- Close | Drop | 11 Mpps | 10.9 Mpps Far | Drop | 4.4 Mpps | 5.8 Mpps Close | TX | 6.5 Mpps | 6.5 Mpps Far | TX | 3.5 Mpps | 4 Mpps Improvement is about 30% drop packet rate, 15% tx packet rate for numa far test. No degradation for numa close tests. TCP single/multi cpu/stream: NUMA | #cpu | Before | After -------------------------------------- Close | 1 | 18 Gbps | 18 Gbps Far | 1 | 15 Gbps | 18 Gbps Close | 12 | 80 Gbps | 80 Gbps Far | 12 | 68 Gbps | 80 Gbps In all test cases we see improvement for the far numa case, and no impact on the close numa case. ================== Performance analysis and conclusions by Jesper [1]: Impact on XDP drop x86_64 is inconclusive and shows only 0.3459ns slow-down, as this is below measurement accuracy of system. v2->v3: - Rebase on top of latest net-next and Jesper's page pool object release patchset [2] - No code changes - Performance analysis by Jesper added to the cover letter. v1->v2: - Drop last patch, as requested by Ilias and Jesper. - Fix documentation's performance numbers order. [1] https://github.com/xdp-project/xdp-project/blob/master/areas/mem/page_pool04_inflight_changes.org#performance-notes [2] https://patchwork.ozlabs.org/cover/1192098/ ==================== Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net/mlx5e: Rx, Update page pool numa node when changedSaeed Mahameed
Once every napi poll cycle, check if numa node is different than the page pool's numa id, and update it using page_pool_update_nid(). Alternatively, we could have registered an irq affinity change handler, but page_pool_update_nid() must be called from napi context anyways, so the handler won't actually help. Performance testing: XDP drop/tx rate and TCP single/multi stream, on mlx5 driver while migrating rx ring irq from close to far numa: mlx5 internal page cache was locally disabled to get pure page pool results. CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G) XDP Drop/TX single core: NUMA | XDP | Before | After --------------------------------------- Close | Drop | 11 Mpps | 10.9 Mpps Far | Drop | 4.4 Mpps | 5.8 Mpps Close | TX | 6.5 Mpps | 6.5 Mpps Far | TX | 3.5 Mpps | 4 Mpps Improvement is about 30% drop packet rate, 15% tx packet rate for numa far test. No degradation for numa close tests. TCP single/multi cpu/stream: NUMA | #cpu | Before | After -------------------------------------- Close | 1 | 18 Gbps | 18 Gbps Far | 1 | 15 Gbps | 18 Gbps Close | 12 | 80 Gbps | 80 Gbps Far | 12 | 68 Gbps | 80 Gbps In all test cases we see improvement for the far numa case, and no impact on the close numa case. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20page_pool: Don't recycle non-reusable pagesSaeed Mahameed
A page is NOT reusable when at least one of the following is true: 1) allocated when system was under some pressure. (page_is_pfmemalloc) 2) belongs to a different NUMA node than pool->p.nid. To update pool->p.nid users should call page_pool_update_nid(). Holding on to such pages in the pool will hurt the consumer performance when the pool migrates to a different numa node. Performance testing: XDP drop/tx rate and TCP single/multi stream, on mlx5 driver while migrating rx ring irq from close to far numa: mlx5 internal page cache was locally disabled to get pure page pool results. CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G) XDP Drop/TX single core: NUMA | XDP | Before | After --------------------------------------- Close | Drop | 11 Mpps | 10.9 Mpps Far | Drop | 4.4 Mpps | 5.8 Mpps Close | TX | 6.5 Mpps | 6.5 Mpps Far | TX | 3.5 Mpps | 4 Mpps Improvement is about 30% drop packet rate, 15% tx packet rate for numa far test. No degradation for numa close tests. TCP single/multi cpu/stream: NUMA | #cpu | Before | After -------------------------------------- Close | 1 | 18 Gbps | 18 Gbps Far | 1 | 15 Gbps | 18 Gbps Close | 12 | 80 Gbps | 80 Gbps Far | 12 | 68 Gbps | 80 Gbps In all test cases we see improvement for the far numa case, and no impact on the close numa case. The impact of adding a check per page is very negligible, and shows no performance degradation whatsoever, also functionality wise it seems more correct and more robust for page pool to verify when pages should be recycled, since page pool can't guarantee where pages are coming from. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20page_pool: Add API to update numa nodeSaeed Mahameed
Add page_pool_update_nid() to be called by page pool consumers when they detect numa node changes. It will update the page pool nid value to start allocating from the new effective numa node. This is to mitigate page pool allocating pages from a wrong numa node, where the pool was originally allocated, and holding on to pages that belong to a different numa node, which causes performance degradation. For pages that are already being consumed and could be returned to the pool by the consumer, in next patch we will add a check per page to avoid recycling them back to the pool and return them to the page allocator. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20Merge branch 'cpsw-switchdev'David S. Miller
Grygorii Strashko says: ==================== net: ethernet: ti: introduce new cpsw switchdev based driver Thank you All for review of v6. There are no significant changes in this version, just fixed comments to v6. --- v6 The major change in this version is DT bindings conversation to json-schema, and fixed other comments to v5. Also added patch to clean up ALE on init and netif restart. --- v5 The major part of work done in this iteration is rebasing on top of net-next with XDP series from Ivan Khoronzhuk [3], and enable XDP support in the new CPSW switchdev driver (it was little bit painful ;(). There are mostly no functional changes in new CPSW driver, just few fixes, sync with old driver and cleanups/optimizations. So, I've kept rest of cover letter unchanged. --- This series originally based on work [1][2] done by Ilias Apalodimas <ilias.apalodimas@linaro.org>. This the RFC v5 which introduces new CPSW switchdev based driver which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. The Switch mode can be enabled by configuring devlink driver parameter "switch_mode" to 1/true: devlink dev param set platform/48484000.switch \ name switch_mode value 1 cmode runtime This can be done regardless of the state of Port's netdev devices - UP/DOWN, but Port's netdev devices have to be in UP before joining the bridge to avoid overwriting of bridge configuration as CPSW switch driver completely reloads its configuration when first Port changes its state to UP. When the both interfaces joined the bridge - CPSW switch driver will start marking packets with offload_fwd_mark flag unless "ale_bypass=0". All configuration is implemented via switchdev API. The previous solution of tracking both Ports joined the bridge (from netdevice_notifier) proved to be not correct as changing CPSW switch driver mode required cleanup of ALE table and CPSW settings which happens while second Port is joined bridge and as result configuration loaded by bridge for the first Port became corrupted. The introduction of the new CPSW switchdev based driver (cpsw_new.c) is split on two parts: Part 1 - basic dual-emac driver; Part 2 switchdev support. Such approach has simplified code development and testing alot. And, I hope, it will help with better review. patches #1 - 5: preparation patches which also moves common code to cpsw_priv.c patches #6 - 9: Introduce TI CPSW switch driver based on switchdev and new DT bindings patch #10: new CPSW switchdev driver documentation patch #11: adds DT nodes for new CPSW switchdev driver added for DRA7 SoC patch #12: adds DT nodes for new cpsw switchdev driver for am571x-idk board patch #13: enables build of TI CPSW driver Most of the contents of the previous cover-letter have been added in new driver documentation, so please refer to that for configuration, testing and future work. These patches can be found at (branch contains some additional patches required for testing on top of net-next): https://github.com/grygoriyS/linux.git branch: lkml-5.4-switch-tbd-v7 changes in v7: - patch 2: added check for devm_kmalloc_array() return value - patch 6: fixed comments changes in v6: https://lkml.org/lkml/2019/11/9/108 - DT bindings converted to json-schema - netdev initialization is split on creation and registration. The netdevs registration happens now at the end of the pobe. - reworked cpsw_set_pauseparam() to use PHYlib APIs. - other comments for v5 fixed v5: https://patchwork.kernel.org/cover/11208785/ - rebase on top of net-next with XDP series from Ivan Khoronzhuk [3], and enable XDP support in the new CPSW switchdev driver cpsw driver (tested XDP_DROP only) - sync with old cpsw driver - implement comments from Ivan Khoronzhuk and Rob Herring - fixed "NETDEV WATCHDOG: .." warning after interface after interface UP/DOWN, missed TX wake in cpsw_adjust_link() v4: https://patchwork.kernel.org/cover/11010523/ - finished split of common CPSW code - added devlink support - changed CPSW mode configuration approach: from netdevice_notifier to devlink parameter - refactor and clean up ALE changes which allows to modify VLANs/MDBs entries - added missed support for port QDISC_CBS and QDISC_MQPRIO - the CPSW is split on two parts: basic dual_mac driver and switchdev support - added missed callback .ndo_get_port_parent_id() - reworked ingress frames marking in switch mode (offload_fwd_mark) - applied comments from Andrew Lunn v3: https://lwn.net/Articles/786677/ Changes in v3: - alot of work done to split properly common code between legacy and switchdev CPSW drivers and clean up code - CPSW switchdev interface updated to the current LKML switchdev interface - actually new CPSW switchdev based driver introduced - optimized dual_mac mode in new driver. Main change is that in promiscuous mode P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current port) instead of ALE_BYPASS. So, port in non promiscuous mode will keep possibility of mcast and vlan filtering. - changed bridge join sequnce: now switch mode will be enabled only when both ports joined the bridge. CPSW will be switched to dual_mac mode if any port leave bridge. ALE table is completly cleared and then refiled while switching to switch mode - this simplidies code a lot, but introduces some limitation to bridge setup sequence: ip link add name br0 type bridge ip link set dev br0 type bridge ageing_time 1000 ip link set dev br0 type bridge vlan_filtering 0 <- disable echo 0 > /sys/class/net/br0/bridge/default_vlan ip link set dev sw0p1 up <- add ports ip link set dev sw0p2 up ip link set dev sw0p1 master br0 ip link set dev sw0p2 master br0 echo 1 > /sys/class/net/br0/bridge/default_vlan <- enable ip link set dev br0 type bridge vlan_filtering 1 bridge vlan add dev br0 vid 1 pvid untagged self - STP tested with vlan_filtering 1/0. To make STP work I've had to set NO_SA_UPDATE for all slave ports (see comment in code). It also required to statically register STP mcast address {0x01, 0x80, 0xc2, 0x0, 0x0, 0x0}; - allowed build both TI_CPSW and TI_CPSW_SWITCHDEV drivers - PTP can be enabled on both ports in dual_mac mode [1] https://patchwork.ozlabs.org/cover/929367/ [2] https://patches.linaro.org/cover/136709/ [3] https://patchwork.kernel.org/cover/11035813/ ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20arm: omap2plus_defconfig: enable new cpsw switchdev driverGrygorii Strashko
Add CONFIG_TI_CPSW_SWITCHDEV option to enable new cpsw switchdev driver Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20ARM: dts: am571x-idk: enable for new cpsw switch dev driverGrygorii Strashko
Add DT nodes for new cpsw switchdev driver for am571x-idk board for now to enable testing of the new solution. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20ARM: dts: dra7: add dt nodes for new cpsw switch dev driverGrygorii Strashko
Add DT nodes for new cpsw switch dev driver. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20Documentation: networking: add cpsw switchdev based driver documentationIlias Apalodimas
A new cpsw dirver based on switchdev was added. Add documentation about basic configuration and future features Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20phy: ti: phy-gmii-sel: dependency from ti cpsw-switchdev driverGrygorii Strashko
Add dependency from TI_CPSW_SWITCHDEV. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ethernet: ti: introduce cpsw switchdev based driver part 2 - switchIlias Apalodimas
CPSW switchdev based driver which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. The Switch mode can be enabled by configuring devlink driver parameter "switch_mode" to 1: devlink dev param set platform/48484000.switch \ name switch_mode value 1 cmode runtime This can be done regardless of the state of Port's netdevs - UP/DOWN, but Port's netdev devices have to be UP before joining the bridge to avoid overwriting of bridge configuration as CPSW switch driver completely reloads its configuration when first Port changes its state to UP. When the both interfaces joined the bridge - CPSW switch driver will start marking packets with offload_fwd_mark flag unless "ale_bypass=0". All configuration is implemented via switchdev API and notifiers. Supported: - SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD - SWITCHDEV_ATTR_ID_PORT_STP_STATE - SWITCHDEV_OBJ_ID_PORT_VLAN - SWITCHDEV_OBJ_ID_PORT_MDB - SWITCHDEV_OBJ_ID_HOST_MDB Hence CPSW switchdev driver supports: - FDB offloading - MDB offloading - VLAN filtering and offloading - STP Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emacIlias Apalodimas
Part 1: Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. Main differences from legacy CPSW driver are: - optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in promiscuous mode will keep possibility of mcast and vlan filtering, which is provides significant benefits when ports are joined to the same bridge, but without enabling "switch" mode, or to different bridges. - learning disabled on ports as it make not too much sense for segregated ports - no forwarding in HW. - enabled basic support for devlink. devlink dev show platform/48484000.switch devlink dev param show platform/48484000.switch: name ale_bypass type driver-specific values: cmode runtime value false - "ale_bypass" devlink driver parameter allows to enable ALE_CONTROL(4).BYPASS mode for debug purposes. - updated DT bindings. Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20dt-bindings: net: ti: add new cpsw switch driver bindingsGrygorii Strashko
Add bindings for the new TI CPSW switch driver. Comparing to the legacy bindings (net/cpsw.txt): - ports definition follows DSA bindings (net/dsa/dsa.txt) and ports can be marked as "disabled" if not physically wired. - all deprecated properties dropped; - all legacy propertiies dropped which represent constant HW cpapbilities (cpdma_channels, ale_entries, bd_ram_size, mac_control, slaves, active_slave) - TI CPTS DT properties are reused as is, but grouped in "cpts" sub-node - TI Davinci MDIO DT bindings are reused as is, because Davinci MDIO is reused. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ethernet: ti: cpsw: move set of common functions in cpsw_privGrygorii Strashko
As a preparatory patch to add support for a switchdev based cpsw driver, move common functions to cpsw-priv.c so that they can be used across both drivers. Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ethernet: ti: cpsw: resolve build deps of cpsw driversGrygorii Strashko
A following patches introduce new CPSW switchdev driver which uses common code with legacy CPSW driver. This will introduce build dependency between CPSW switchdev and CPSW legacy drivers related to for_each_slave() and cpsw_slave_index() - they can be compiled both, but only one of them will be not functional depending in Kconfig settings due to duffrences in Slave Ports indexes calculation. To fix this make for_each_slave() local (it's used now only by legacy CPSW driver) and convert cpsw_slave_index() to be a function pointer which is assigned in probe. Driver to probe is defined by DT. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ethernet: ti: ale: modify vlan/mdb api for switchdevIlias Apalodimas
A following patch introduces switchdev functionality, so modify ALE engine VLANs/MDBs API: - cpsw_ale_del_mcast(): update so it will remove only selected ports from mcast port_mask or delete whole mcast record if !port_mask - cpsw_ale_del_vlan(): update so it will remove only selected ports from all VLAN record's masks or delete whole VLAN record if !port_mask - add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's masks - add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ethernet: ti: cpsw: allow untagged traffic on host portGrygorii Strashko
Now untagged vlan traffic is not support on Host P0 port. This patch adds in ALE context bitmap of VLANs for which Host P0 port bit set in Force Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap(). Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: ethernet: ti: ale: clean ale tbl on init and intf restartGrygorii Strashko
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete or garbage entries from ALE table. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20Merge branch 'nf_tables_offload-vlan-matching-support'David S. Miller
Pablo Neira Ayuso says: ==================== nf_tables_offload: vlan matching support The following patchset contains Netfilter support for vlan matching offloads: 1) Constify nft_reg_load() as a preparation patch. 2) Restrict rule matching to ingress interface type ARPHRD_ETHER. 3) Add new vlan_tci field to flow_dissector_key_vlan structure, to allow to set up vlan_id, vlan_dei and vlan_priority in one go. 4) C-VLAN matching support. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20netfilter: nft_payload: add C-VLAN offload supportPablo Neira Ayuso
Match on h_vlan_encapsulated_proto and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20netfilter: nft_payload: add VLAN offload supportPablo Neira Ayuso
Match on ethertype and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20netfilter: nf_tables_offload: allow ethernet interface type onlyPablo Neira Ayuso
Hardware offload support at this stage assumes an ethernet device in place. The flow dissector provides the intermediate representation to express this selector, so extend it to allow to store the interface type. Flower does not uses this, so skb_flow_dissect_meta() is not extended to match on this new field. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20netfilter: nf_tables: constify nft_reg_load{8, 16, 64}()Pablo Neira Ayuso
This patch constifies the pointer to source register data that is passed as an input parameter. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20lwtunnel: add support for multiple geneve optsXin Long
geneve RFC (draft-ietf-nvo3-geneve-14) allows a geneve packet to carry multiple geneve opts, so it's necessary for lwtunnel to support adding multiple geneve opts in one lwtunnel route. But vxlan and erspan opts are still only allowed to add one option. With this patch, iproute2 could make it like: # ip r a 1.1.1.0/24 encap ip id 1 geneve_opts 0:0:12121212,1:2:12121212 \ dst 10.1.0.2 dev geneve1 # ip r a 1.1.1.0/24 encap ip id 1 vxlan_opts 456 \ dst 10.1.0.2 dev erspan1 # ip r a 1.1.1.0/24 encap ip id 1 erspan_opts 1:123:0:0 \ dst 10.1.0.2 dev erspan1 Which are pretty much like cls_flower and act_tunnel_key. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19cxgb4: remove unneeded semicolon for switch blockRahul Lakkireddy
Semicolon is not required at the end of switch block. So, remove it. Addresses coccinelle warning: drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon Fixes: 4846d5330daf ("cxgb4: add Tx and Rx path for ETHOFLD traffic") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19net: dsa: felix: Fix CPU port assignment when not last portVladimir Oltean
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch and the ENETC: - eno2 <-> swp4, at 2.5G - eno3 <-> swp5, at 1G Only one of the above Ethernet port pairs can act as a DSA link for tagging. When adding initial support for the driver, it was tested only on the 1G eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially (which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't support fixed-link speeds higher than 1G). After making PHYLINK work, it appears that swp4 still can't act as CPU port. So it looks like ocelot_set_cpu_port was being called for swp4, but then it was called again for swp5, overwriting the CPU port assigned in the DT. It appears that when you call dsa_upstream_port for a port that is not defined in the device tree (such as swp5 when using swp4 as CPU port), its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu, and this trips up the following condition in dsa_upstream_port: if (!cpu_dp) return port; So the moral of the story is: don't call dsa_upstream_port for a port that is not defined in the device tree, and therefore its dsa_port structure is not completely initialized (ds->num_ports is still 6). Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18net: phy: dp83869: fix return of uninitialized variable retColin Ian King
In the case where the call to phy_interface_is_rgmii returns zero the variable ret is left uninitialized and this is returned at the end of the function dp83869_configure_rgmii. Fix this by returning 0 instead of the uninitialized value in ret. Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18lwtunnel: change to use nla_put_u8 for LWTUNNEL_IP_OPT_ERSPAN_VERXin Long
LWTUNNEL_IP_OPT_ERSPAN_VER is u8 type, and nla_put_u8 should have been used instead of nla_put_u32(). This is a copy-paste error. Fixes: b0a21810bd5e ("lwtunnel: add options setting and dumping for erspan") Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18Merge branch 'bnxt_en-Updates'David S. Miller
Michael Chan says: ==================== bnxt_en: Updates. This series has the firmware interface update that changes the aRFS/ntuple interface on 57500 chips. The 2nd patch adds a counter and improves the hardware buffer error handling on the 57500 chips. The rest of the series is mainly enhancements on error recovery and firmware reset. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18bnxt_en: Abort waiting for firmware response if there is no heartbeat.Pavan Chebbi
This is especially beneficial during the NVRAM related firmware commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND flag gets set while waiting for firmware response, abort and return error. Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18bnxt_en: Add a warning message for driver initiated resetVasundhara Volam
During loss of heartbeat, log this warning message. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18bnxt_en: Return proper error code for non-existent NVM variableVasundhara Volam
For NVM params that are not supported in the current NVM configuration, return the error as -EOPNOTSUPP. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18bnxt_en: Report health status update after reset is doneVasundhara Volam
Report health status update to devlink health reporter, once reset is completed. Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>