| Age | Commit message (Collapse) | Author |
|---|
|
A recent commit removed the only use of ipa_cmd_dma_task_32b_addr_add().
This function (and the IPA immediate command it implements) is no
longer needed, so get rid of it, along with all of the definitions
associated with it. Isolate its removal in a commit so it can be
easily added back again if needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous commit made ipa_endpoint_stop() be a trivial wrapper
around gsi_channel_stop(). Since it no longer does anything
special, just open-code it in the three places it's used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only reason ipa_endpoint_stop() had a retry loop was that the
just-removed workaround required an IPA DMA command to occur between
attempts. The gsi_channel_stop() call that implements the stop does
its own retry loop, to cover a channel's transition from started to
stop-in-progress to stopped state.
Get rid of the unnecessary retry loop in ipa_endpoint_stop().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ipa_endpoint_stop(), a workaround is used for IPA version 3.5.1
where a 1-byte DMA request is issued between GSI channel stop
retries.
It turns out that this workaround is only required for IPA versions
3.1 and 3.2, and we don't support those. So remove the call to
ipa_endpoint_stop_rx_dma() in that function. That leaves that
function unused, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ipa_endpoint_stop(), for TX endpoints we set the number of retries
to 0. When we break out of the loop, retries being 0 means we return
EIO rather than the value of ret (which should be 0).
Fix this by using a non-zero retry count for both RX and TX
channels, and just break out of the loop after calling
gsi_channel_stop() for TX channels. This way only RX channels
will retry, and the retry count will be non-zero at the end
for TX channels (so the proper value gets returned).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 713b6ebb4c376b3fb65fdceb3b59e401c93248f9)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alex Elder says:
====================
net: ipa: kill endpoint delay mode workaround
A "delay mode" feature was put in place to work around a problem
where packets could passed to the modem before it was ready to
handle them. That problem no longer exists, and we don't need the
workaround any more so get rid of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A "delay mode" feature was put in place to work around a problem
that was observed during development of the upstream IPA driver. It
used TX endpoint "delay mode" in order to prevent transmitting
packets toward the modem before it was ready.
A race condition that would explain the problem has long since been
fixed, and we have concluded that the "delay mode" feature is no
longer required. So get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new helper function that encapsulates enabling or disabling
suspend on an RX endpoint. It returns the previous state of the
endpoint (true means suspend mode was enabled).
Create another function that handles enabling or disabling delay mode
on a TX endpoint. Delay mode does not work correctly on IPA version
4.2, so we don't currently use it (and shouldn't).
We only set delay mode in one case, and although we don't expect an
endpoint to already be in delay mode, it doesn't really matter if it
was. So the delay function doesn't return a value.
Stop issuing warnings if the previous suspend or delay mode state
differs from what is expected.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change ipa_endpoint_init_ctrl() so it returns the previous state
(whether suspend or delay mode was enabled) rather than indicating
whether the request caused a change in state. This makes it easier
to understand what's happening where called.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alex Elder says:
====================
net: ipa: limit special reset handling
Some special handling done during channel reset should only be done
for IPA hardare version 3.5.1. This series generalizes the meaning
of a flag passed to indicate special behavior, then has the special
handling be used only when appropriate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In gsi_channel_reset(), RX channels are subjected to two consecutive
CHANNEL_RESET commands. This workaround should only be used for IPA
version 3.5.1, and for newer hardware "can lead to unwanted behavior."
Only issue the second CHANNEL_RESET command for legacy hardware.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In several places, a Boolean flag is used in the GSI code to
indicate whether the "doorbell engine" should be enabled or not
when a channel is configured. This is basically done to abstract
this property from the IPA version; the GSI code doesn't otherwise
"know" what the IPA hardware version is. The doorbell engine is
enabled only for IPA v3.5.1, not for IPA v4.0 and later.
The next patch makes another change that affects behavior during
channel reset (which also involves programming the channel). It
also distinguishes IPA v3.5.1 hardware from newer hardware.
Rather than creating another flag whose value matches the "db_enable"
value, just rename "db_enable" to be "legacy" so it can be used to
signal more than just the special doorbell handling.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
tcp: minor adjustments for low pacing rates
After pacing horizon addition, we have to adjust how we arm rto
timer, otherwise we might freeze very low pacing rate flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As hinted in prior change ("tcp: refine tcp_pacing_delay()
for very low pacing rates"), it is probably best arming
the xmit timer only when all the packets have been scheduled,
rather than when the head of rtx queue has been re-sent.
This does matter for flows having extremely low pacing rates,
since their tp->tcp_wstamp_ns could be far in the future.
Note that the regular xmit path has a stronger limit
in tcp_small_queue_check(), meaning it is less likely to
go beyond the pacing horizon.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the addition of horizon feature to sch_fq, we noticed some
suboptimal behavior of extremely low pacing rate TCP flows, especially
when TCP is not aware of a drop happening in lower stacks.
Back in commit 3f80e08f40cd ("tcp: add tcp_reset_xmit_timer() helper"),
tcp_pacing_delay() was added to estimate an extra delay to add to standard
rto timers.
This patch removes the skb argument from this helper and
tcp_reset_xmit_timer() because it makes more sense to simply
consider the time at which next packet is allowed to be sent,
instead of the time of whatever packet has been sent.
This avoids arming RTO timer too soon and removes
spurious horizon drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an "iommus" property to the IPA node in "sdm845.dtsi". It is
required because there are two regions of memory the IPA accesses
through an SMMU. The next few patches define and map those regions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heiner Kallweit says:
====================
timer: add fsleep for flexible sleeping
Sleeping for a certain amount of time requires use of different
functions, depending on the time period.
Documentation/timers/timers-howto.rst explains when to use which
function, and also checkpatch checks for some potentially
problematic cases.
So let's create a helper that automatically chooses the appropriate
sleep function -> fsleep(), for flexible sleeping
Not sure why such a helper doesn't exist yet, or where the pitfall is,
because it's a quite obvious idea.
If the delay is a constant, then the compiler should be able to ensure
that the new helper doesn't create overhead. If the delay is not
constant, then the new helper can save some code.
First user is the r8169 network driver. If nothing speaks against it,
then this series could go through the netdev tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new flexible sleep function fsleep() to merge the udelay and msleep
polling functions. We can safely do this because no polling function
is used in atomic context in this driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sleeping for a certain amount of time requires use of different
functions, depending on the time period.
Documentation/timers/timers-howto.rst explains when to use which
function, and also checkpatch checks for some potentially
problematic cases.
So let's create a helper that automatically chooses the appropriate
sleep function -> fsleep(), for flexible sleeping
If the delay is a constant, then the compiler should be able to ensure
that the new helper doesn't create overhead. If the delay is not
constant, then the new helper can save some code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the upcoming rev of RFC4941 (IPv6 temporary addresses):
https://tools.ietf.org/html/draft-ietf-6man-rfc4941bis-09
* Reduces the default Valid Lifetime to 2 days
The number of extra addresses employed when Valid Lifetime was
7 days exacerbated the stress caused on network
elements/devices. Additionally, the motivation for temporary
addresses is indeed privacy and reduced exposure. With a
default Valid Lifetime of 7 days, an address that becomes
revealed by active communication is reachable and exposed for
one whole week. The only use case for a Valid Lifetime of 7
days could be some application that is expecting to have long
lived connections. But if you want to have a long lived
connections, you shouldn't be using a temporary address in the
first place. Additionally, in the era of mobile devices, general
applications should nevertheless be prepared and robust to
address changes (e.g. nodes swap wifi <-> 4G, etc.)
* Employs different IIDs for different prefixes
To avoid network activity correlation among addresses configured
for different prefixes
* Uses a simpler algorithm for IID generation
No need to store "history" anywhere
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Walle says:
====================
add phy shared storage
Introduce the concept of a shared PHY storage which can be used by some
QSGMII PHYs to ease initialization and access to global per-package
registers.
Changes since v2:
- restore page to standard after reading the base address in the mscc
driver, thanks Antoine.
Changes since v1:
- fix typos and add a comment, thanks Florian.
- check for "addr < 0" in phy_package_join()
- remove multiple blank lines and make "checkpatch.pl --strict" happy
Changes since RFC:
- check return code of kzalloc()
- fix local variable ordering (reverse christmas tree)
- add priv_size argument to phy_package_join()
- add Tested-by tag, thanks Vladimir.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new phy_package_shared common storage to ease the package
initialization and to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new phy_package_shared common storage to ease the package
initialization and to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are packages which contain multiple PHY devices, eg. a quad PHY
transceiver. Provide functions to allocate and free shared storage.
Usually, a quad PHY contains global registers, which don't belong to any
PHY. Provide convenience functions to access these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 27c6feb0fb33a665a746346e76714826a5be5d10.
For ipsec offload the chelsio's ethernet driver expects a single mtu
sized packet.
But when ipsec traffic is running using iperf, most of the packets in
that traffic are gso packets(large sized skbs) because GSO is enabled by
default in TCP, due to this commit 0a6b2a1dc2a2 ("tcp: switch to GSO
being always on"), so chcr_ipsec_offload_ok() receives a gso
skb(with gso_size non zero).
Due to the check in chcr_ipsec_offload_ok(), this function returns false
for most of the packet, then ipsec offload is skipped and the skb goes
out taking the coprocessor path which reduces the bandwidth for inline
ipsec.
If this check is removed then for most of the packets(large sized skbs)
the chcr_ipsec_offload_ok() returns true and then as GSO is on, the
segmentation of the packet happens in the kernel and then finally the
driver_xmit is called, which receives a segmented mtu sized packet which
is what the driver expects for ipsec offload. So this case becomes
unnecessary here, therefore removing it.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:427:20: warning:
symbol 'enetc_act_fwd' was not declared. Should it be static?
drivers/net/ethernet/freescale/enetc/enetc_qos.c:966:20: warning:
symbol 'enetc_check_flow_actions' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Julian Wiedmann says:
====================
s390/qeth: updates 2020-05-06
please apply the following patch series for qeth to netdev's net-next
tree.
Same patches as yesterday, except that the ethtool reset has been
dropped for now.
This primarily adds infrastructure to deal with HW offloads when the
packets get forwarded over the adapter's internal switch.
Aside from that, just some minor tweaking for the TX code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove a stale doc link. While at it also reword the help text to get
rid of an outdated marketing term.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When starting the reset worker via sysfs is unsuccessful, return an
error to the user.
Modernize the sysfs input parsing while at it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When qeth_flush_buffers() gets called for a group of TX buffers
(currently up to 2 for OSA-style devices), the code iterates over each
buffer for some final processing.
During this processing, it sets the TX IRQ marker on the leading buffer
rather than the last one. This can result in delayed TX completion of
the trailing buffers. So pull the IRQ marker code out of the loop, and
apply it to the final buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX path usually maps the full content of a page into a buffer
element. But there's specific skb layouts (ie. linearized TSO skbs)
where the HW header (1) requires a separate buffer element, and (2) is
page-contiguous with the packet data that's mapped into the next buffer
element.
Flag such buffer elements accordingly, so that HW can optimize its data
access for them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge the __qeth_fill_buffer() helper into its only caller. This way all
mapping-related context is in one place, and we can make some more use
of it in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current OSA models don't support TSO for traffic to local next-hops, and
some old models didn't offer TX CSO for such packets either.
So as part of .ndo_features_check, check if a packet's next-hop resides
on the same OSA Adapter. Opt out from affected HW offloads accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These will be used in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For debugging purposes, provide read access to the local_addr caches
via debug/qeth/<dev_name>/local_addrs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In configurations where specific HW offloads are in use, OSA adapters
will raise notifications to their virtual devices about the IP addresses
that currently reside on the same adapter.
Cache these addresses in two RCU-enabled hash tables, and flush the
tables once the relevant HW offload(s) get disabled.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling TX CSO, make a note of whether the device has support for
LP2LP offloading. This will become relevant in subsequent patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following sparse warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:68:5: warning:
symbol 'mtk_m32' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
drivers/net/ethernet/mellanox/mlx4/en_ethtool.c:1238:5-8: Unneeded
variable: "err". Return "0" on line 1252
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
net/bridge/br_private.h:1334:8-9: WARNING: return of 0/1 in function
'br_mrp_enabled' with return type bool
Fixes: 6536993371fab ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes coccicheck warning:
drivers/net/ethernet/ti/am65-cpts.c:1017:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's possible to have build configuration which will force PTP_1588_CLOCK=m
and so TI_K3_AM65_CPTS=m while still have TI_K3_AM65_CPSW_NUSS=y. This will
cause build failures:
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.o: in function `am65_cpsw_init_cpts':
../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685: undefined reference to `am65_cpts_create'
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685:(.text+0x2e20):
relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `am65_cpts_create'
Fix it by adding dependencies from CPTS in TI_K3_AM65_CPSW_NUSS as below:
config TI_K3_AM65_CPSW_NUSS
...
depends on TI_K3_AM65_CPTS || !TI_K3_AM65_CPTS
Note. This will create below dependencies and for NFS boot + CPTS all of them
have to be built-in.
PTP_1588_CLOCK -> TI_K3_AM65_CPTS -> TI_K3_AM65_CPSW_NUSS
While here, clean up TI_K3_AM65_CPTS definition.
Fixes: b1f66a5bee07 ("net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
