| Age | Commit message (Collapse) | Author |
|---|
|
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: update the group mask on mark addition
inotify: fix length reporting and size checking
inotify: do not send a block of zeros when no pathname is available
|
|
On Tue, Aug 18, 2009 at 01:45:17PM -0400, John David Anglin wrote:
> CC arch/parisc/kernel/traps.o
> arch/parisc/kernel/traps.c: In function 'handle_interruption':
> arch/parisc/kernel/traps.c:535:18: warning: operation on 'regs->iasq[0]'
> may be undefined
Yes - Line 535 should use both [0] and [1].
Reported-by: John David Anglin <dave@hiauly1.hia.nrc.ca>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes the bug that was reported in
http://bugzilla.kernel.org/show_bug.cgi?id=14053
If we're in the case where we need to force a reencode and then resend of
the RPC request, due to xprt_transmit failing with a networking error, then
we _must_ retransmit the entire request.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
> James Bottomley (1):
> module: workaround duplicate section names
-tip testing found that this patch breaks the build on x86 if
CONFIG_KALLSYMS is disabled:
kernel/module.c: In function ‘load_module’:
kernel/module.c:2367: error: ‘struct module’ has no member named ‘sect_attrs’
distcc[8269] ERROR: compile kernel/module.c on ph/32 failed
make[1]: *** [kernel/module.o] Error 1
make: *** [kernel] Error 2
make: *** Waiting for unfinished jobs....
Commit 1b364bf misses the fact that section attributes are only
built and dealt with if kallsyms is enabled. The patch below fixes
this.
( note, technically speaking this should depend on CONFIG_SYSFS as
well but this patch is correct too and keeps the #ifdef less
intrusive - in the KALLSYMS && !SYSFS case the code is a NOP. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Replaced patch with a slightly cleaner variation by James Bottomley ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix vSMP boot crash
x86, xen: Initialize cx to suppress warning
x86, xen: Suppress WP test on Xen
|
|
acpi_video_put_one_device was attempting to remove sysfs entries and
unregister a backlight device without first checking that said backlight
device structure had been created.
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Return from bt_rfkill_poll() when hci_get_radio_state() fails.
value is invalid in that case and should not be assigned to the rfkill
state.
This also fixes a double unlock bug.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Fix a compatibility issue when the same buffer or string is
stored to itself. This has been seen in the field. Previously,
ACPICA would zero out the buffer/string. Now, the operation is
treated as a NOP.
http://bugzilla.acpica.org/show_bug.cgi?id=803
Reported-by: Rezwanul Kabir <Rezwanul_Kabir@Dell.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Bartlomiej Zolnierkiewicz reported an atomic order-6 allocation failure
for ipw2200 firmware loading in kernel 2.6.30. High order allocation is
likely to fail and should always be avoided.
The patch fixes this problem by replacing the original order-6
pci_alloc_consistent() with an array of order-1 pages from a pci pool.
This utilized the ipw2200 DMA command blocks (up to 64 slots). The
maximum firmware size support remains the same (64*8K).
This patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14016
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Seperating the addition and update of marks in inotify resulted in a
regression in that inotify never gets events. The inotify group mask is
always 0. This mask should be updated any time a new mark is added.
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
0db501bd0610ee0c0 introduced a regresion in that it now sends a nul
terminator but the length accounting when checking for space or
reporting to userspace did not take this into account. This corrects
all of the rounding logic.
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
When an event has no pathname, there's no need to pad it with a null byte and
therefore generate an inotify_event sized block of zeros. This fixes a
regression introduced by commit 0db501bd0610ee0c0aca84d927f90bcccd09e2bd where
my system wouldn't finish booting because some process was being confused by
this.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
Per-cpu counters are an ASLR information leak as they show
the execution other tasks do. Increase the paranoia level
to 1, which disallows per-cpu counters. (they still allow
counting/profiling of own tasks - and admin can profile
everything.)
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In commit a5a0a630922a2f6a774b6dac19f70cb5abd86bb0, when
ocfs2_attch_dentry_lock fails, we call an extra iput and reset
dentry->d_fsdata to NULL. This resolve a bug, but it isn't
completed and the dentry is still there. When we want to use
it again, ocfs2_dentry_revalidate doesn't catch it and return
true. That make future ocfs2_dentry_lock panic out.
One bug is http://oss.oracle.com/bugzilla/show_bug.cgi?id=1162.
The resolution is to add a check for dentry->d_fsdata in
revalidate process and return false if dentry->d_fsdata is NULL,
so that a new ocfs2_lookup will be called again.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
|
|
The root cause is a duplicate section name (.text); is this legal?
[ Amerigo Wang: "AFAIK, yes." ]
However, there's a problem with commit
6d76013381ed28979cd122eb4b249a88b5e384fa in that if you fail to allocate
a mod->sect_attrs (in this case it's null because of the duplication),
it still gets used without checking in add_notes_attrs()
This should fix it
[ This patch leaves other problems, particularly the sections directory,
but recent parisc toolchains seem to produce these modules and this
prevents a crash and is a minimal change -- RR ]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rarely-used symbol_put_addr() needs to use dereference_function_descriptor
on powerpc.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As soon as the framebuffer is registered, our methods may be called by the
kernel. This leads to a crash as xenfb_refresh() gets called before we have
the irq.
Connect to the backend before registering our framebuffer with the kernel.
[ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: Ensure we alwasy write the terminating NULL.
inotify: fix locking around inotify watching in the idr
inotify: do not BUG on idr entries at inotify destruction
inotify: seperate new watch creation updating existing watches
|
|
We call lmb_end_of_DRAM() to test whether a DMA mask is ok on a machine
without IOMMU, but this function is marked as __init.
I don't think there's a clean way to get the top of RAM max_pfn doesn't
appear to include highmem or I missed (or we have a bug :-) so for now,
let's just avoid having a broken 2.6.31 by making this function
non-__init and we can revisit later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: update documentation pointers
9p: remove unnecessary v9fses->options which duplicates the mount string
net/9p: insulate the client against an invalid error code sent by a 9p server
9p: Add missing cast for the error return value in v9fs_get_inode
9p: Remove redundant inode uid/gid assignment
9p: Fix possible regressions when ->get_sb fails.
9p: Fix v9fs show_options
9p: Fix possible memleak in v9fs_inode_from fid.
9p: minor comment fixes
9p: Fix possible inode leak in v9fs_get_inode.
9p: Check for error in return value of v9fs_fid_add
|
|
Add a check in ip_append_data() for NULL *rtp to prevent future bugs in
callers from being exploitable.
Signed-off-by: Julien Tinnes <julien@cr0.org>
Signed-off-by: Tavis Ormandy <taviso@sdf.lonestar.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
kAFS crashes when asked to read a symbolic link because page_getlink()
passes a NULL file pointer to read_mapping_page(), but afs_readpage()
expects a file pointer from which to extract a key.
Modify afs_readpage() to request the appropriate key from the calling
process's keyrings if a file struct is not supplied with one attached.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before the rewrite copy_event_to_user always wrote a terqminating '\0'
byte to user space after the filename. Since the rewrite that
terminating byte was skipped if your filename is exactly a multiple of
event_size. Ouch!
So add one byte to name_size before we round up and use clear_user to
set userspace to zero like /dev/zero does instead of copying the
strange nul_inotify_event. I can't quite convince myself len_to_zero
will never exceed 16 and even if it doesn't clear_user should be more
efficient and a more accurate reflection of what the code is trying to
do.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
The are races around the idr storage of inotify watches. It's possible
that a watch could be found from sys_inotify_rm_watch() in the idr, but it
could be removed from the idr before that code does it's removal. Move the
locking and the refcnt'ing so that these have to happen atomically.
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
If an inotify watch is left in the idr when an fsnotify group is destroyed
this will lead to a BUG. This is not a dangerous situation and really
indicates a programming bug and leak of memory. This patch changes it to
use a WARN and a printk rather than killing people's boxes.
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
There is nothing known wrong with the inotify watch addition/modification
but this patch seperates the two code paths to make them each easy to
verify as correct.
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
virtio: net refill on out-of-memory
smc91x: fix compilation on SMP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/ps3: Update ps3_defconfig
powerpc/ps3: Add missing check for PS3 to rtc-ps3 platform device registration
|
|
Update ps3_defconfig.
o Refresh for 2.6.31.
o Remove MTD support.
o Add more HID drivers.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On non-PS3, we get:
| kernel BUG at drivers/rtc/rtc-ps3.c:36!
because the rtc-ps3 platform device is registered unconditionally in a kernel
with builtin support for PS3.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
IMA: iint put in ima_counts_get and put
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k,m68knommu: Wire up rt_tgsigqueueinfo and perf_counter_open
m68k: Fix redefinition of pgprot_noncached
arch/m68k/include/asm/motorola_pgalloc.h: fix kunmap arg
m68k: cnt reaches -1, not 0
m68k: count can reach 51, not 50
|
|
If we change the inverted attribute to another value, the LED will not be
inverted until we change the GPIO state.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When setting the same GPIO number, multiple IRQ shared requests will be
done without freing the previous request. It will also try to free a
failed request or an already freed IRQ if 0 was written to the gpio file.
All these oops and leaks were fixed with the following solution: keep the
previous allocated GPIO (if any) still allocated in case the new request
fails. The alternative solution would desallocate the previous allocated
GPIO and set gpio as 0.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This failure is very common on many platforms. Handling it in the ACPI
processor driver is enough, and we don't need a warning message unless
CONFIG_ACPI_DEBUG is set.
Based on a patch from Zhang Rui.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the BIOS reports an invalid throttling state (which seems to be
fairly common after system boot), a reset is done to state T0.
Because of a check in acpi_processor_get_throttling_ptc(), the reset
never actually gets executed, which results in the error reoccurring
on every access of for example /proc/acpi/processor/CPU0/throttling.
Add a 'force' option to acpi_processor_set_throttling() to ensure
the reset really takes effect.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389
This patch, together with the next one, fixes a regression introduced in
2.6.30, listed on the regression list. They have been available for 2.5
months now in bugzilla, but have not been picked up, despite various
reminders and without any reason given.
Google shows that numerous people are hitting this issue. The issue is in
itself relatively minor, but the bug in the code is clear.
The patches have been in all my kernels and today testing has shown that
throttling works correctly with the patches applied when the system
overheats (http://bugzilla.kernel.org/show_bug.cgi?id=13918#c14).
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Summary:
Kernel panic arise when stack protection is enabled, since strncat will
add a null terminating byte '\0'; So in functions
like this one (wmi_query_block):
char wc[4]="WC";
....
strncat(method, block->object_id, 2);
...
the length of wc should be n+1 (wc[5]) or stack protection
fault will arise. This is not noticeable when stack protection is
disabled,but , isn't good either.
Config used: [CONFIG_CC_STACKPROTECTOR_ALL=y,
CONFIG_CC_STACKPROTECTOR=y]
Panic Trace
------------
.... stack-protector: kernel stack corrupted in : fa7b182c
2.6.30-rc8-obelisco-generic
call_trace:
[<c04a6c40>] ? panic+0x45/0xd9
[<c012925d>] ? __stack_chk_fail+0x1c/0x40
[<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
[<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
[<fa7e7000>] ? acer_wmi_init+0x00/0x61a [acer_wmi]
[<fa7e7135>] ? acer_wmi_init+0x135/0x61a [acer_wmi]
[<c0101159>] ? do_one_initcall+0x50+0x126
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13514
Signed-off-by: Costantino Leandro <lcostantino@gmail.com>
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Jens reported early_ioremap messages with old ASUS board...
> [ 1.507461] pci 0000:00:09.0: Firmware left e100 interrupts enabled; disabling
> [ 1.532778] early_ioremap(3fffd080, 0000005c) [0] => Pid: 1, comm: swapper Not tainted 2.6.31-rc4 #36
> [ 1.561007] Call Trace:
> [ 1.568638] [<c136e48b>] ? printk+0x18/0x1d
> [ 1.581734] [<c15513ff>] __early_ioremap+0x74/0x1e9
> [ 1.596898] [<c15515aa>] early_ioremap+0x1a/0x1c
> [ 1.611270] [<c154a187>] __acpi_map_table+0x18/0x1a
> [ 1.626451] [<c135a7f8>] acpi_os_map_memory+0x1d/0x25
> [ 1.642129] [<c119459c>] acpi_tb_verify_table+0x20/0x49
> [ 1.658321] [<c1193e50>] acpi_get_table_with_size+0x53/0xa1
> [ 1.675553] [<c1193eae>] acpi_get_table+0x10/0x15
> [ 1.690192] [<c155cc19>] acpi_processor_init+0x23/0xab
> [ 1.706126] [<c1001043>] do_one_initcall+0x33/0x180
> [ 1.721279] [<c155cbf6>] ? acpi_processor_init+0x0/0xab
> [ 1.737479] [<c106893a>] ? register_irq_proc+0xaa/0xc0
> [ 1.753411] [<c10689b7>] ? init_irq_proc+0x67/0x80
> [ 1.768316] [<c15405e7>] kernel_init+0x120/0x176
> [ 1.782678] [<c15404c7>] ? kernel_init+0x0/0x176
> [ 1.797062] [<c10038b7>] kernel_thread_helper+0x7/0x10
> [ 1.812984] 00000080 + ffe00000
that is rather later.
acpi_gbl_permanent_mmap should be set in acpi_early_init()
if acpi is not disabled
and we have
> [ 0.000000] ASUS P2B-DS detected: force use of acpi=ht
just don't load acpi_processor_init...
Reported-and-tested-by: Jens Rosenboom <jens@leia.mcbone.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The return value of the get_temp function is not checked when doing a
thermal zone update. This may lead to a critical shutdown if get_temp
fails and the content of the temp variable is incorrectly set higher than
the critical trip point.
This has been observed on a system with incorrect ACPI implementation
where the corresponding methods were not serialized and therefore
sometimes triggered ACPI errors (AE_ALREADY_EXISTS). The following
critical shutdowns indicated a temperature of 2097 C, which was obviously
wrong.
The patch adds a return value check that jumps over all trip point
evaluations printing a warning if get_temp fails. The trip points are
evaluated again on the next polling interval with successful get_temp
execution.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Spotted by Hiroshi Shimamoto who also provided the test-case below.
copy_process() uses signal->count as a reference counter, but it is not.
This test case
#include <sys/types.h>
#include <sys/wait.h>
#include <unistd.h>
#include <stdio.h>
#include <errno.h>
#include <pthread.h>
void *null_thread(void *p)
{
for (;;)
sleep(1);
return NULL;
}
void *exec_thread(void *p)
{
execl("/bin/true", "/bin/true", NULL);
return null_thread(p);
}
int main(int argc, char **argv)
{
for (;;) {
pid_t pid;
int ret, status;
pid = fork();
if (pid < 0)
break;
if (!pid) {
pthread_t tid;
pthread_create(&tid, NULL, exec_thread, NULL);
for (;;)
pthread_create(&tid, NULL, null_thread, NULL);
}
do {
ret = waitpid(pid, &status, 0);
} while (ret == -1 && errno == EINTR);
}
return 0;
}
quickly creates an unkillable task.
If copy_process(CLONE_THREAD) races with de_thread()
copy_signal()->atomic(signal->count) breaks the signal->notify_count
logic, and the execing thread can hang forever in kernel space.
Change copy_process() to increment count/live only when we know for sure
we can't fail. In this case the forked thread will take care of its
reference to signal correctly.
If copy_process() fails, check CLONE_THREAD flag. If it it set - do
nothing, the counters were not changed and current belongs to the same
thread group. If it is not set, ->signal must be released in any case
(and ->count must be == 1), the forked child is the only thread in the
thread group.
We need more cleanups here, in particular signal->count should not be used
by de_thread/__exit_signal at all. This patch only fixes the bug.
Reported-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
An mlocked page might lose the isolatation race. This causes the page to
clear PG_mlocked while it remains in a VM_LOCKED vma. This means it can
be put onto the [in]active list. We can rescue it by using try_to_unmap()
in shrink_page_list().
But now, As Wu Fengguang pointed out, vmscan has a bug. If the page has
PG_referenced, it can't reach try_to_unmap() in shrink_page_list() but is
put into the active list. If the page is referenced repeatedly, it can
remain on the [in]active list without being moving to the unevictable
list.
This patch fixes it.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: KOSAKI Motohiro <<kosaki.motohiro@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's problematic to allow signed element_nr's or total's to be passed as
part of the flex array API.
flex_array_alloc() allows total_nr_elements to be set to a negative
quantity, which is obviously erroneous.
flex_array_get() and flex_array_put() allows negative array indices in
dereferencing an array part, which could address memory mapped before
struct flex_array.
The fix is to convert all existing element_nr formals to be qualified as
unsigned. Existing checks to compare it to total_nr_elements or the max
array size based on element_size need not be changed.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The `parts' member of struct flex_array should evaluate to an incomplete
type so that sizeof() cannot be used and C99 does not require the
zero-length specification.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
flex_array_free_parts() does not take `src' or `element_nr' formals, so
remove their respective comments.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If all array elements fit into the base structure and data is copied using
flex_array_put() starting at a non-zero index, flex_array_get() will fail
to return the data.
This fixes the bug by only checking for NULL parts when all elements do
not fit in the base structure when flex_array_get() is used. Otherwise,
fa_element_to_part_nr() will always be 0 since there are no parts
structures needed and such element may never have been put. Thus, it will
remain NULL due to the kzalloc() of the base.
Additionally, flex_array_put() now only checks for a NULL part when all
elements do not fit in the base structure. This is otherwise unnecessary
since the base structure is guaranteed to exist (or we would have already
hit a NULL pointer).
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix incorrect verdict check and returns error if device_create failed,
otherwise driver triggers kernel oops.
Signed-off-by: Joonwoo Park<joonwpark81@gmail.com>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ima_counts_get() calls ima_iint_find_insert_get() which takes a reference
to the iint in question, but does not put that reference at the end of the
function. This can lead to a nasty memory leak. Easy enough to reproduce:
#include <sys/mman.h>
#include <stdio.h>
int main (void)
{
int i;
void *ptr;
for (i=0; i < 100000; i++) {
ptr = mmap(NULL, 4096, PROT_READ|PROT_WRITE,
MAP_SHARED|MAP_ANONYMOUS, -1, 0);
if (ptr == MAP_FAILED)
return 2;
munmap(ptr, 4096);
}
return 0;
}
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
|
|
arch/m68k/include/asm/pgtable_mm.h:148:1: warning: "pgprot_noncached" redefined
In file included from arch/m68k/include/asm/pgtable_mm.h:138,
from arch/m68k/include/asm/pgtable.h:4,
from include/linux/mm.h:40,
from include/linux/pagemap.h:7,
from include/linux/blkdev.h:12,
from arch/m68k/emu/nfblock.c:17:
include/asm-generic/pgtable.h:133:1: warning: this is the location of the previous definition
pgprot_noncached() should be defined _before_ including asm-generic/pgtable.h
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
