| Age | Commit message (Collapse) | Author |
|---|
|
Choose console BPP that supports RGB and remove the old fbdev bpp
selection code. LCDC on AM335x has red and blue wires switched between
24 bit and 16 bit colors. If 24 format is wired for RGB colors, the 16
bit format is wired for BGR. drm_fbdev_cma_init() does not currently
like anything else but RGB formats, so we must choose such bytes per
pixel value that supports RGB.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add "blue-and-red-wiring"-device tree property and update devicetree
binding document.
The red and blue components are reversed between 24 and 16 bit modes
on am335x LCDC output pins. To get 24 RGB format the red and blue
wires has to be crossed and this in turn causes 16 colors output to be
in BGR format. With straight wiring the 16 color is RGB and 24 bit is
BGR.
The new property describes whether the red and blue wires are crossed
or not. If the property is not present or its value is not recognized
the legacy mode is assumed. The legacy configuration supports RGB565,
RGB888 and XRGB8888 formats. However, depending on wiring, the red and
blue colors are swapped in either 16 or 24-bit color modes.
For more details see section 3.1.1 in AM335x Silicon Errata:
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Write DMA base and ceiling address with a single instruction, if
available. This should make it more unlikely that LCDC would fetch the
DMA addresses in the middle of an update. Having bad combination of
addresses in dma base and ceiling (e.g base > ceiling) can cause
unpredictaple behavior in LCDC.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
drm_helper_disable_unused_functions() should not be called by atomic
drivers.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This got accidentally dropped in the fixed commit and is required for
the driver to properly work on the rev1 IP, such as found on the LCDK.
Fixes: 2b2080d7e9ae ("drm/tilcdc: Get rid of complex ping-pong mechanism")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
The LCDC seems to expect its framebuffer ceiling address pointer to be
an inclusive bound. The IP rev2 seems to cope with that but rev1 (as
found on the LCDK) don't.
Also note that this is what the framebuffer code does in da8xx-fb.c.
Since, as the TRM puts it, "The 2 LSBs are hardwired to 00b", the
dma_addr_t can be decremented without cast.
I tested it with a v2 (AM335x, rev 0x4F201000) and an LCDK (v1).
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
In function tilcdc_get_external_components the check for
the remote port parent is not correct. We need a '||' instead of
an '&&'.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
This reverts commit d10571fc4fba7d57fb8157f0be61dcbe4a7965ca.
This isn't how we get to do this unfortunately.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
More -misc stuff
- moar drm_crtc.c split up&documentation
- some fixes for the simple kms helpers (Andrea)
- I included all the dri1 patches from David - we're not removing any code
or drivers, and it seems to have worked as a wake-up call to motivate a
few more people to upstream kms conversions for these. Feel free to
revert if you disagree strongly.
- a few other single patches
* tag 'topic/drm-misc-2016-08-31' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm: drm_probe_helper: Fix output_poll_work scheduling
drm: bridge/dw-hdmi: Fix colorspace and scan information registers values
drm/doc: Polish docs for drm_property&drm_property_blob
drm: Unify handling of blob and object properties
drm: Extract drm_property.[hc]
drm: move drm_mode_legacy_fb_format to drm_fourcc.c
drm/doc: Polish docs for drm_mode_object
drm: Remove drm_mode_object->atomic_count
drm: Extract drm_mode_object.[hc]
drm/doc: Polish kerneldoc for encoders
drm: Extract drm_encoder.[hc]
drm/fb-helper: don't call remove_conflicting_framebuffers for FB=m && DRM=y
drm/atomic-helper: Add NO_DISABLE_AFTER_MODESET flag support for plane commit
drm/atomic-helper: Disable appropriate planes in disable_planes_on_crtc()
drm/atomic-helper: Add atomic_disable CRTC helper callback
drm: simple_kms_helper: add support for bridges
drm: simple_kms_helper: make connector optional at init time
drm/bridge: introduce bridge detaching mechanism
drm/simple-helpers: Always add planes to the state update
drm: reduce GETCLIENT to a minimum
...
|
|
drm_kms_helper_poll_enable_locked() should check if we have delayed event
pending and if we have, schedule the work to run without delay.
Currently the output_poll_work is only scheduled if any of the connectors
have DRM_CONNECTOR_POLL_CONNECT or DRM_CONNECTOR_POLL_DISCONNECT with
DRM_OUTPUT_POLL_PERIOD delay. It does not matter if we have delayed event
already registered to be handled. The detection will be delayd by
DRM_OUTPUT_POLL_PERIOD in any case.
Furthermore if none of the connectors are marked as POLL_CONNECT or
POLL_DISCONNECT because all connectors are either POLL_HPD or they are
always connected: the output_poll_work will not run at all even if we
have delayed event marked.
When none of the connectors require polling, their initial status change
from unknown to connected/disconnected is not going to be handled until
the first kms application starts or if we have fb console enabled.
Note that in general the output poll work should be enabled already
when this happens, but at driver load usually the first probe happens
before the output polling is enabled. This patch fixes this case.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[danvet: Note when exactly this is an issue, since the probe code
schedules the poll work itself already.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160831110905.31289-1-peter.ujfalusi@ti.com
|
|
Colorspace and scan information values were being written in wrong
offsets. This patch corrects this and writes the values at the
offsets specified in the databook.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/96fd0f06b7ebc2ee5cb8239a99648f3107e24497.1471530573.git.joabreu@synopsys.com
|
|
- remove kerneldoc for drm-internal functions
- drm_property_replace_global_blob isn't actually atomic, and doesn't
need to be. Update docs&comments to match
- document all the types and try to link things a bit better
- nits all over
v2: Appease checkpatch in the moved code (Archit)
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-9-daniel.vetter@ffwll.ch
|
|
They work exactly the same now, after the refcounting unification a bit
ago. The only reason they're distinct is backwards compat with existing
userspace.
Cc: Daniel Stone <daniels@collabora.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-8-daniel.vetter@ffwll.ch
|
|
This just contains the base property classes and all the code to
handle blobs. I think for any kind of standardized/shared properties
it's better to have separate files - this is fairly big already as-is.
v2: resurrect misplaced hunk (Daniel Stone)
Cc: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-7-daniel.vetter@ffwll.ch
|
|
It's part of the drm fourcc handling code, mapping the old depth/bpp
values to new fourcc codes.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-6-daniel.vetter@ffwll.ch
|
|
I figured an overview section here is overkill, and better
to just document the 2 structures themselves well enough.
v2: Review from Archit:
- Appease checkpatch in moved code.
- Spelling fixes in the kerneldoc.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-5-daniel.vetter@ffwll.ch
|
|
It's only used in drm_mode_object_get_properties, and we can compute
it there directly with a bit of code shuffling.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-4-daniel.vetter@ffwll.ch
|
|
Just for the struct drm_mode_object base class. The header file was
already partially extracted to help untangle the include loops.
v2:
- Also move the generic get/set property ioctls. At first this seemed
like a bad idea since it requires making drm_mode_crtc_set_obj_prop
non-static. But eventually that will get split away too (like
the connector version already is) for both crtc and planes. Hence I
reconsidered.
- drm_mode_object.[hc] instead of drm_modeset.[hc], which requires
renaming the drm_modeset.h header I already started building up.
This is more consistent (matches the name of the main structure),
and I want to be able to use drm_modeset.[hc] for the basic modeset
init/cleanup functionality like drm_mode_config_init.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-3-daniel.vetter@ffwll.ch
|
|
- Move missing bits into struct drm_encoder docs.
- Explain that encoders are 95% internal and only 5% uapi, and that in
general the uapi part is broken.
- Remove verbose comments for functions not exposed to drivers.
v2: Review from Archit:
- Appease checkpatch in the moved code.
- Make it clearer that bridges are not exposed to userspace.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-2-daniel.vetter@ffwll.ch
|
|
Same treatment as before. Only hiccup is drm_crtc_mask, which
unfortunately can't be resolved until drm_crtc.h is less of a monster.
Untangle the header loop with a forward declaration for that static
inline.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-1-daniel.vetter@ffwll.ch
|
|
When CONFIG_DRM_KMS_FB_HELPER is disabled, we can have a configuration
in which some DRM drivers are built-in, but the framebuffer core is a
loadable module. This results in a link error, such as:
drivers/gpu/drm/radeon/radeon.o: In function `radeon_pci_probe':
radeon_kfd.c:(.text.radeon_pci_probe+0xbc): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/amd/amdgpu/amdgpu.o: In function `amdgpu_pci_probe':
amdgpu_mn.c:(.text.amdgpu_pci_probe+0xa8): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/mgag200/mgag200.o: In function `mga_vram_init':
mgag200_ttm.c:(.text.mga_vram_init+0xa8): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/mgag200/mgag200.o: In function `mga_pci_probe':
mgag200_ttm.c:(.text.mga_pci_probe+0x88): undefined reference to `remove_conflicting_framebuffers'
Makefile:969: recipe for target 'vmlinux' failed
This changes the compile-time check to IS_REACHABLE, which means we end up
not calling remove_conflicting_framebuffers() in the configuration, which
seems good enough, as we know that no framebuffer driver is loaded by the
time that the built-in DRM driver calls remove_conflicting_framebuffers.
We could alternatively avoid the link error by forcing CONFIG_FB to not
be a module in this case, but that wouldn't change anything at runtime,
and just make the already convoluted set of dependencies worse here.
I could not find out what happens if the fbdev driver gets loaded as
a module after the DRM driver is already initialized, but that is a case
that can happen with or without this patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0a3bfe29f816 ("drm/fb-helper: Fix the dummy remove_conflicting_framebuffers")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829123428.3260105-1-arnd@arndb.de
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
|
|
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
|
|
Currently, the helper drm_atomic_helper_disable_planes_on_crtc() calls
->atomic_disable for all planes _to be_ enabled on a particular CRTC.
This is obviously wrong for those planes which are not scanning out frames
when the helper is called. Instead, it's sane to disable active planes
of old_crtc_state in the helper.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472196644-30563-3-git-send-email-gnuiyl@gmail.com
|
|
Some display controllers need plane(s) to be disabled together with
the relevant CRTC, e.g., the IPUv3 display controller for imx-drm.
This patch adds atomic_disable CRTC helper callback so that
old_crtc_state(as a parameter of the callback) could be used
to get the active plane(s) of the old CRTC state for disable operation.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472196644-30563-2-git-send-email-gnuiyl@gmail.com
|
|
Introduce drm_simple_display_pipe_attach_bridge() and
drm_simple_display_pipe_detach_bridge() in order to make it possible to use
drm encoders with the simple display pipes managed by simple_kms_helpers
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-3-git-send-email-andrea.merello@gmail.com
|
|
drm_simple_display_pipe_init() pretends to attach a connector
to the display pipe.
In case a drm bridge has to be used, then it's the bridge that
takes care of connectors.
This patch makes the connector parameter optional for
drm_simple_display_pipe_init(), so that a drm bridge could
handle connector by itself later.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-2-git-send-email-andrea.merello@gmail.com
|
|
Up to now, once a bridge has been attached to a DRM device, it cannot
be undone.
In particular you couldn't rmmod/insmod a DRM driver that uses a bridge,
because the bridge would remain bound to the first (dead) driver instance.
This patch fixes this by introducing drm_encoder_detach() and a ->detach
callback in drm_bridge_funcs for the bridge to be notified about detaches.
It's DRM/KMS driver responsibility to call drm_encoder_detach().
While adding the bridge detach callback, with its kerneldoc, I also added
kerneldoc for attach callback.
Few other kerneldocs fixes around there are included.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-1-git-send-email-andrea.merello@gmail.com
|
|
Our update function is hooked to the single plane, which might not get
called for crtc-only updates. Which is surprising, so fix this by
always adding the plane.
While at it document how&when the event should be sent out better in
the kerneldoc.
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: andrea.merello@gmail.com
Tested-and-Reported-by: andrea.merello@gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471933540-31131-1-git-send-email-daniel.vetter@ffwll.ch
|
|
The *only* known user of GETCLIENT is libva, which uses it to check
whether its own context is authenticated. It used to iterate all clients,
look for one that matches its own pid and then check its state.
The entire purpose for us to still have a GETCLIENT implementation is to
serve libva. So lets not pretend we do anything else: Make this function
return information on the caller's context only, fake the PID to the
caller's pid so they always match, and just fill in the "authenticated"
bit, nothing else.
This patch reduces the complexity of GETCLIENT to a bare minimum, avoids
any dependency on priv->uid or priv->pid (allows us to get rid of them),
and makes libva happy by always *exactly* returning the information it
wants.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160825143505.7447-1-dh.herrmann@gmail.com
|
|
The legacy DRI1 drivers expose highly broken interfaces to user-space. No
modern system should enable them, or you will effectively allow user-space
to circumvent most of your kernel security measures. The DRI1 kernel APIs
are simply broken.
User-space can always use vesafb/efifb/simplefb and friends to get working
graphics.
Lets hide the old drivers behind CONFIG_BROKEN. In case they turn out to
be still used (really?), we can easily revert this and figure out a way to
move them out of sight (e.g., moving all DRI1 drivers to
drivers/gpu/dri1/).
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160804080657.9664-2-dh.herrmann@gmail.com
|
|
Lets move forward and hide the remaining DRI1 drivers behind a config
option, so we have a central place to disable them all. Furthermore, we
can provide a clear warning to anyone enabling them.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160804080657.9664-1-dh.herrmann@gmail.com
|
|
into drm-next
First drm-next pull for radeon and amdgpu for 4.9. Highlights:
- powerplay support for iceland asics
- improved GPU reset (both full asic and per block)
- UVD and VCE powergating for CZ and ST
- VCE clockgating for CZ and ST
- Support for pre-initialized (e.g., zeroed) vram buffers
- ttm cleanups
- virtual display support
- core and radeon/amdgpu support for page_flip_target
- lots of bug fixes and clean ups
* 'drm-next-4.9' of git://people.freedesktop.org/~agd5f/linux: (171 commits)
drm/amdgpu: use memcpy_toio for VCE firmware upload
drm/amdgpu: use memcpy_to/fromio for UVD fw upload
drm/amd/powerplay: delete useless code in iceland_hwmgr.c.
drm/radeon: switch UVD code to use UVD_NO_OP for padding
drm/amdgpu: switch UVD code to use UVD_NO_OP for padding
drm/radeon: add support for UVD_NO_OP register
drm/amdgpu: add support for UVD_NO_OP register
drm/amdgpu: fix VCE ib alignment value
drm/amdgpu: fix IB alignment for UVD
drm/amd/amdgpu: Print ring name in amdgpu_ib_schedule()
drm/radeon: remove dead code, si_mc_load_microcode (v2)
drm/radeon/cik: remove dead code (v2)
drm/amd/powerplay: avoid NULL dereference, cz_hwmgr.c
drm/amd/powerplay: avoid NULL pointer dereference
drm/amdgpu/gmc8: remove dead code (v2)
drm/amdgpu/gmc7: remove dead code (v2)
drm/amdgpu: Fix indentation in dce_v8_0_audio_write_sad_regs()
drm/amdgpu: Use correct mask in dce_v8_0_afmt_setmode() and fix comment typos.
drm/amdgpu: cleanup amdgpu_vm_bo_update params
drm/amdgpu: stop adding dummy entry in amdgpu_ttm_placement_init
...
|
|
into drm-next
drm-intel-next-2016-08-22:
- bugfixes and cleanups for rcu-protected requests (Chris)
- atomic modeset fixes for gpu reset on pre-g4x (Maarten&Ville)
- guc submission improvements (Dave Gordon)
- panel power sequence cleanup (Imre)
- better use of stolen and unmappable ggtt (Chris), plus prep work to make that
happen
- rework of framebuffer offsets, prep for multi-plane framebuffers (Ville)
- fully partial ggtt vmaps, including fenced ones (Chris)
- move lots more of the gem tracking from the object to the vma (Chris)
- tune the command parser (Chris)
- allow fbc without fences on recent platforms (Chris)
- fbc frontbuffer tracking fixes (Chris)
- fast prefaulting using io-mappping.h pgprot caching (Chris)
* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (141 commits)
io-mapping: Fixup for different names of writecombine
io-mapping.h: s/PAGE_KERNEL_IO/PAGE_KERNEL/
drm/i915: Update DRIVER_DATE to 20160822
drm/i915: Use remap_io_mapping() to prefault all PTE in a single pass
drm/i915: Embed the io-mapping struct inside drm_i915_private
io-mapping: Always create a struct to hold metadata about the io-mapping
drm/i915/fbc: Allow on unfenced surfaces, for recent gen
drm/i915/fbc: Don't set an illegal fence if unfenced
drm/i915: Flush delayed fence releases after reset
drm/i915: Reattach comment, complete type specification
drm/i915/cmdparser: Accelerate copies from WC memory
drm/i915/cmdparser: Use binary search for faster register lookup
drm/i915/cmdparser: Check for SKIP descriptors first
drm/i915/cmdparser: Compare against the previous command descriptor
drm/i915/cmdparser: Improve hash function
drm/i915/cmdparser: Only cache the dst vmap
drm/i915/cmdparser: Use cached vmappings
drm/i915/cmdparser: Add the TIMESTAMP register for the other engines
drm/i915/cmdparser: Make initialisation failure non-fatal
drm/i915: Stop discarding GTT cache-domain on unbind vma
...
|
|
into drm-next
This pull request contains the following rockchip drm changes:
- Introduce support for rk3399 vop/crtc
- Add PSR framework to the rockchip driver
- Implement PSR in the rockchip analogix edp driver
- Fix panel on/off in analogix to avoid damaging panels
- Some miscellaneous fixes to clean up logs and code readability
* 'for-next' of git://people.freedesktop.org/~seanpaul/dogwood:
drm/rockchip: analogix_dp: drop unnecessary probe deferral "error" print
drm/rockchip: Enable vblank without event
drm/rockchip: Improve analogix-dp psr handling
drm/rockchip: A couple small fixes to psr
drm/rockchip: Use a spinlock to protect psr state
drm/rockchip: Don't use a delayed worker for psr state changes
drm/rockchip: Convert psr_list_mutex to spinlock and use it
drm/rockchip: analogix_dp: implement PSR function
drm/bridge: analogix_dp: add the PSR function support
drm/rockchip: add an common abstracted PSR driver
drm/rockchip: vop: export line flag function
drm/bridge: analogix_dp: Ensure the panel is properly prepared/unprepared
dt-bindings: add compatible strings for big/little rockchip vops
dt-bindings: sort Rockchip vop compatible by chip's number
drm/rockchip: vop: add rk3399 vop support
drm/rockchip: vop: introduce VOP_REG_MASK
drm/rockchip: sort registers define by chip's number
|
|
Try to be clean here, even when it's a noop on x86.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Also use the firmware size from the header instead of calculating it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Replace packet2's with packet0 writes to UVD_NO_OP. The
value written to UVD_NO_OP does not matter.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Replace packet2's with packet0 writes to UVD_NO_OP. The
value written to UVD_NO_OP does not matter.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Writes to this register are the preferred way to do NOPs.
Bump the driver version as well.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Writes to this register are the preferred way to do NOPs.
Bump the driver version as well.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The VCE rings only require single dword alignment.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
According to the hw team, it should be 16, not 8.
Cc: Peter Fang <peter.fang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: b754b35b089d ("vgaarbiter: rst-ifiy and polish kerneldoc")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160824101916.30125-1-daniel.vetter@ffwll.ch
|
|
Somehow architectures can't agree on this. And for good measure make
sure we have a fallback which should work everywhere (fingers
crossed).
v2: Make it compile properly, needs a defined() for the #elif.
Fixes: ac96b5566926 ("io-mapping.h: s/PAGE_KERNEL_IO/PAGE_KERNEL/")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: linux-mm@kvack.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160823202233.4681-1-daniel.vetter@ffwll.ch
(cherry picked from commit 80c33624e4723c4e22d9917cd676067ebf652dc2)
|
|
PAGE_KERNEL_IO is an x86-ism. Though it is used to define the pgprot_t
used for the iomapped region, it itself is just PAGE_KERNEL. On all
other arches, PAGE_KERNEL_IO is undefined so in a general header we must
refrain from using it.
v2: include pgtable for pgprot_combine()
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: cafaf14a5d8f ("io-mapping: Always create a struct to hold metadata about the io-mapping")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: linux-mm@kvack.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160823155024.22379-1-chris@chris-wilson.co.uk
(cherry picked from commit ac96b5566926af83463ddcf4655856033c092f26)
|
|
Commit d112a8163f83 ("gma500/cdv: Add eDP support") replaced the
code inside this if-conditional with gma_backlight_set(), which
becomes a nop stub if CONFIG_BACKLIGHT_CLASS_DEVICE is disabled.
So, there is no need to guard the caller with config_enabled().
Note:
This is one of remaining TODOs to deprecate config_enabled() macro.
Refer to commit 97f2645f358b ("tree-wide: replace config_enabled()
with IS_ENABLED()").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471970574-23906-1-git-send-email-yamada.masahiro@socionext.com
|
|
Everyone knows them, except all the new folks joining from the ARM
side haven't lived through all the pain of the past years and are
entirely surprised when I raise this. Definitely time to document
this.
Last time this was a big discussion was about 6 years ago, when qcom
tried to land a kernel driver without userspace. Dave Airlie made the
rules really clear:
http://airlied.livejournal.com/73115.html
This write-up here is essentially what I've put into a presentation a
while ago, which was also reviewed by Dave:
http://blog.ffwll.ch/2015/05/gfx-kernel-upstreaming-requirements.html
v2: Fix typos Eric&Rob spotted.
v3: Nitpick from Jani.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
A few bigger things:
- start of splitting drm_crtc.c into more manageable and better documneted
chunks
- DRM_DEV_* logging (Sean)
* tag 'topic/drm-misc-2016-08-23' of git://anongit.freedesktop.org/drm-intel: (46 commits)
drm/fb-helper: Make docs for fb_set_suspend wrappers consistent
drm/rockchip: Delete unnecessary assignment for the field "owner"
drm/bridge: dw-hdmi: Delete unnecessary assignment for the field "owner"
drm/rockchip: Don't continue trying to enable crtc on failure
drm/fb-helper: Add drm_fb_helper_set_suspend_unlocked()
drm/fb-helper: Fix the dummy remove_conflicting_framebuffers
drm/udl: Ensure channel is selected before using the device.
drm: Avoid calling dev_printk(.dev = NULL)
drm: avoid exposing kernel stack in compat_drm_getstats
reservation: fix small comment typo
drm: Don't implement empty prepare_fb()/cleanup_fb()
virtio-gpu: Use memdup_user() rather than duplicating its implementation
GPU-DRM-Savage: Use memdup_user() rather than duplicating
drm: Allow drivers to modify plane_state in prepare_fb/cleanup_fb
drm/rockchip: Use DRM_DEV_ERROR in vop
drm: Introduce DRM_DEV_* log messages
drm/edid: CEA mode 64 1080p100 vsync pulse width incorrect
Revert "drm/hisilicon: Don't set drm_device->platformdev"
dma-buf: fix kernel-doc warning and typos
drm: Fix kerneldoc in drm_plane_helper.c
...
|
|
I figured I might as well go ocd and make them booleans and rename the
locked version too.
v2: Review from Noralf.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Fixes: cfe63423d9be ("drm/fb-helper: Add drm_fb_helper_set_suspend_unlocked()")
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160823152727.31788-1-daniel.vetter@ffwll.ch
|
