summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-11-29ath9k/carl9170: advertise P2PJohannes Berg
With some upcoming changes we'd like to use the interface types for P2P capability tests. Enable them now so that when we add those tests in wpa_supplicant, nothing will break. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-29ath9k: use per-device struct for pm_qos_* operationsGabor Juhos
The ath9k driver uses a shared pm_qos_request_list structure for all devices. This causes the following warning if more than one device is present in the system: WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0() pm_qos_add_request() called for already added request Modules linked in: Call Trace: [<802b1cdc>] dump_stack+0x8/0x34 [<8007dd90>] warn_slowpath_common+0x78/0xa4 [<8007de44>] warn_slowpath_fmt+0x2c/0x38 [<801b0828>] ath9k_init_device+0x5e8/0x6b0 [<801bc508>] ath_pci_probe+0x2dc/0x39c [<80176254>] pci_device_probe+0x64/0xa4 [<8019471c>] driver_probe_device+0xbc/0x188 [<80194854>] __driver_attach+0x6c/0xa4 [<80193e20>] bus_for_each_dev+0x60/0xb0 [<80193580>] bus_add_driver+0xcc/0x268 [<80194c08>] driver_register+0xe0/0x198 [<801764e0>] __pci_register_driver+0x50/0xe0 [<80365f48>] ath9k_init+0x3c/0x6c [<8006050c>] do_one_initcall+0xfc/0x1d8 [<80355340>] kernel_init+0xd4/0x174 [<800639a4>] kernel_thread_helper+0x10/0x18 ---[ end trace 5345fc6f870564a6 ]--- This patch fixes that warning by using a separate pm_qos_request_list sructure for each device. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-29libertas: fix invalid accessSven Neumann
card->priv must not be accessed after lbs_remove_card() was called as lbs_remove_card() frees card->priv via free_netdev(). For libertas_sdio this is a regression introduced by 23b149c1890f9. The correct fix to the issue described there is simply to remove the assignment. This flag is set at the appropriate time inside lbs_remove_card anyway. Reported-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-29libertas: fix memory corruption in lbs_remove_card()Daniel Drake
"priv" is stored at the end of the wiphy structure, which is freed during the call to lbs_cfg_free(). It must not be touched afterwards. Remove the unnecessary NULL assignment causing this memory corruption. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-23wireless: b43: fix error path in SDIOGuennadi Liakhovetski
Fix unbalanced call to sdio_release_host() on the error path. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22carl9170: fix virtual interface setup crashChristian Lamparter
This patch fixes a faulty bound check which caused a crash when too many virtual interface were brought up. BUG: unable to handle kernel NULL pointer dereference at 00000004 IP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170] *pde = 00000000 Oops: 0002 [#1] PREEMPT Modules linked in: carl9170 [...] Pid: 4720, comm: wpa_supplicant Not tainted 2.6.37-rc2-wl+ EIP: 0060:[<f8125f67>] EFLAGS: 00210206 CPU: 0 EIP is at carl9170_op_add_interface+0x1d7/0x2c0 [carl9170] EAX: 00000000 ... Process wpa_supplicant Stack: f4f88f34 fffffff4 .. Call Trace: [<f8f4e666>] ? ieee80211_do_open+0x406/0x5c0 [mac80211] [...] Code: <89> 42 04 ... EIP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170] CR2: 0000000000000004 Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22ssb: b43-pci-bridge: Add new vendor for BCM4318Daniel Klaffenbach
Add new vendor for Broadcom 4318. Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22ath9k: fix timeout on stopping rx dmaFelix Fietkau
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough. When it's time to stop DMA, the PCU is still busy, so the rx enable bit never clears. Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster, with this change, I cannot reproduce the rx stop related WARN_ON anymore. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18ath9k_htc: Avoid setting QoS control for non-QoS framesRajkumar Manoharan
Setting tid information in the TX header is required only for QoS frames. Not handling this case causes severe data loss with some APs. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18cfg80211: fix can_beacon_sec_chan, reenable HT40Mark Mentovai
This follows wireless-testing 9236d838c920e90708570d9bbd7bb82d30a38130 ("cfg80211: fix extension channel checks to initiate communication") and fixes accidental case fall-through. Without this fix, HT40 is entirely blocked. Signed-off-by: Mark Mentovai <mark@moxienet.com> Cc: stable@kernel.org Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16cfg80211: fix extension channel checks to initiate communicationLuis R. Rodriguez
When operating in a mode that initiates communication and using HT40 we should fail if we cannot use both primary and secondary channels to initiate communication. Our current ht40 allowmap only covers STA mode of operation, for beaconing modes we need a check on the fly as the mode of operation is dynamic and there other flags other than disable which we should read to check if we can initiate communication. Do not allow for initiating communication if our secondary HT40 channel has is either disabled, has a passive scan flag, a no-ibss flag or is a radar channel. Userspace now has similar checks but this is also needed in-kernel. Reported-by: Jouni Malinen <jouni.malinen@atheros.com> Cc: stable@kernel.org Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16ath9k_hw: Set proper eeprom offset for AR9287 HTC devicesRajkumar Manoharan
AR9287 based PCI & USB devices are differed in eeprom start offset. So set proper the offset for HTC devices to read nvram correctly. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16ath9k_htc: Add new devices into AR7010Rajkumar Manoharan
Treat new PIDs (0xA704, 0x1200) as AR7010 devices. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16ath9k_htc: Update usb device ID listRajkumar Manoharan
Added new VID/PIDs into supported devices list Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16ath9k: Remove pm_qos request after hw unregister.Vivek Natarajan
Update pm_qos before removing it in deinit_device to prevent this warning: pm_qos_update_request() called for unknown object. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15carl9170: fix usb anchor wait timeoutChristian Lamparter
usb_wait_anchor_empty_timeout's @timeout wants milliseconds and not jiffies. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15cfg80211: fix WIPHY_FLAG_IBSS_RSN bitJussi Kivilinna
WIPHY_FLAG_IBSS_RSN is BIT(7) as is WIPHY_FLAG_CONTROL_PORT_PROTOCOL. Change to BIT(8). Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15b43legacy: Fix compile on ARM architectureArnd Hannemann
When b43legacy is compiled on the arm platform, the following errors are seen: CC [M] drivers/net/wireless/b43legacy/xmit.o In file included from include/net/dst.h:11, from drivers/net/wireless/b43legacy/xmit.c:31: include/net/dst_ops.h:28: error: expected ':', ',', ';', '}' or '__attribute__' before '____cacheline_aligned_in_smp' include/net/dst_ops.h: In function 'dst_entries_get_fast': include/net/dst_ops.h:33: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_get_slow': include/net/dst_ops.h:41: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_add': include/net/dst_ops.h:49: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_init': include/net/dst_ops.h:55: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_destroy': include/net/dst_ops.h:60: error: 'struct dst_ops' has no member named 'pcpuc_entries' make[4]: *** [drivers/net/wireless/b43legacy/xmit.o] Error 1 make[3]: *** [drivers/net/wireless/b43legacy] Error 2 make[2]: *** [drivers/net/wireless] Error 2 make[1]: *** [drivers/net] Error 2 make: *** [drivers] Error 2 The cause is a missing include of <linux/cache.h>, which is present for i386 and x86_64 architectures, but not for arm. Signed-off-by: Arnd Hannemann <arnd@arndnet.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-09iwlwifi: dont use pci_dev before it being assignWey-Yi Guy
In order to use build-in debugging macro, pci_dev in priv need to be assigned first. This fix iwl3945 driver oopsed at boot with 2.6.37-rc1 Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-09Bluetooth: Add MacBookAir3,1(2) supportEdgar (gimli) Hucek
Adding the new MacBookAir3,1(2) to btusb. Output without the patch and btusb loaded : T: Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=05ac ProdID=821b Rev= 0.34 S: Manufacturer=Apple Inc. S: Product=Bluetooth USB Host Controller C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Output with the patch and btusb loaded : T: Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=05ac ProdID=821b Rev= 0.34 S: Manufacturer=Apple Inc. S: Product=Bluetooth USB Host Controller C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09Bluetooth: fix not setting security level when creating a rfcomm sessionLuiz Augusto von Dentz
This cause 'No Bonding' to be used if userspace has not yet been paired with remote device since the l2cap socket used to create the rfcomm session does not have any security level set. Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com> Acked-by: Ville Tervo <ville.tervo@nokia.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09Bluetooth: fix endianness conversion in L2CAPGustavo F. Padovan
Last commit added a wrong endianness conversion. Fixing that. Reported-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09Bluetooth: fix unaligned access to l2cap conf datasteven miao
In function l2cap_get_conf_opt() and l2cap_add_conf_opt() the address of opt->val sometimes is not at the edge of 2-bytes/4-bytes, so 2-bytes/4 bytes access will cause data misalignment exeception. Use get_unaligned_le16/32 and put_unaligned_le16/32 function to avoid data misalignment execption. Signed-off-by: steven miao <realmz6@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09Bluetooth: Enable USB autosuspend by default on btusbMatthew Garrett
We've done this for a while in Fedora without any obvious problems other than some interaction with input devices. Those should be fixed now, so let's try this in mainline. Signed-off-by: Matthew Garrett <mjg@redhat.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09Bluetooth: Fix non-SSP auth request for HIGH security level socketsJohan Hedberg
When initiating dedicated bonding a L2CAP raw socket with HIGH security level is used. The kernel is supposed to trigger the authentication request in this case but this doesn't happen currently for non-SSP (pre-2.1) devices. The reason is that the authentication request happens in the remote extended features callback which never gets called for non-SSP devices. This patch fixes the issue by requesting also authentiation in the (normal) remote features callback in the case of non-SSP devices. This rule is applied only for HIGH security level which might at first seem unintuitive since on the server socket side MEDIUM is already enough for authentication. However, for the clients we really want to prefer the server side to decide the authentication requrement in most cases, and since most client sockets use MEDIUM it's better to be avoided on the kernel side for these sockets. The important socket to request it for is the dedicated bonding one and that socket uses HIGH security level. The patch is based on the initial investigation and patch proposal from Andrei Emeltchenko <endrei.emeltchenko@nokia.com>. Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09Bluetooth: fix hidp kconfig dependency warningRandy Dunlap
Fix kconfig dependency warning to satisfy dependencies: warning: (BT_HIDP && NET && BT && BT_L2CAP && INPUT || USB_HID && HID_SUPPORT && USB && INPUT) selects HID which has unmet direct dependencies (HID_SUPPORT && INPUT) Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-08ath9k_hw: Fix memory leak on ath9k_hw_rf_alloc_ext_banks failureRajkumar Manoharan
The allocated externel radio banks have to be freed in case of ath9k_hw_rf_alloc_ext_banks failure. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08ath9k_htc: Fix probe failure if CONFIG_USB_DEBUG enabledRajkumar Manoharan
Since the endpoint descriptors (EP3 & EP4) were changed from Interrupt to Bulk type by firmware, the urb submission done on Bulk pipes. And the recent commit "check the endpoint type against the pipe type" added aditional error checking against pipe types under CONFIG_USB_DEBUG. So bmAttribute has to be updated for both EP3 & EP4 before submitting urbs on that pipe. This patch resolves the following failure. [ 2215.710936] usb 1-1: usb_probe_device [ 2215.710945] usb 1-1: configuration #1 chosen from 1 choice [ 2215.711152] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 2215.711252] ath9k_hif_usb 1-1:1.0: usb_probe_interface [ 2215.711255] ath9k_hif_usb 1-1:1.0: usb_probe_interface - got id [ 2215.712780] usb 1-1: BOGUS urb xfer, pipe 3 != type 1 [ 2215.713782] usb 1-1: ath9k_htc: Unable to allocate URBs [ 2215.713801] ath9k_hif_usb: probe of 1-1:1.0 failed with error -22 Reported-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08ath9k_htc: Add support for device ID 3346Haitao Zhang
This patch adds support for USB dongle with device ID 3346 from IMC Networks. Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08ath9k_hw: Fix AR9280 surprise removal during frequent idle on/offVasanthakumar Thiagarajan
Bit 22 of AR_WA should be set to fix the situation where chip reset is asynchronous to clock of analog shift registers, such that when reset is released, it could mess up the values of analog shift registers and cause some hw issue on AR9280. This bit is write only, but the driver does a read-modify-write on AR_WA without setting bit 22 in ar9002_hw_configpcipowersave() during radio disable. This causes surprise removal of hw. It can never recover from this state and the hw will become usable only after a power on/off cycle, and sometimes only during a cold reboot. This issue can be triggered by doing frequent roaming with the simple/test-roam script available from the wifi-test project [1] when roaming between APs quickly. When roaming there is a is a high possibility that the device being put into idle (radio disable) state by mac80211 during AUTH->ASSOC. A device hardware reset would fail and the kernel would output: [40251.363799] ath: AWAKE -> FULL-SLEEP [40251.363815] ieee80211 phy17: device no longer idle - working [40251.363817] ath: Marking phy17 as not-idle [40251.363819] ath: FULL-SLEEP -> AWAKE [40251.415978] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3) [40251.419896] ath: ah->misc_mode 0x4 [40251.428138] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3) [40251.532247] ath: timeout (100000 us) on reg 0x9860: 0xffffffff & 0x00000001 != 0x00000000 [40251.532250] ath: Unable to reset channel (2462 MHz), reset status -5 [40251.532422] ath: Set channel: 5745 MHz [40251.540639] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.548826] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.557023] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.565211] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.573415] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.581603] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.581606] ath: Failed to stop TX DMA. Resetting hardware! [40251.592679] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff [40251.703330] ath: timeout (100000 us) on reg 0x7000: 0xffffffff & 0x00000003 != 0x00000000 [40251.703333] ath: RTC stuck in MAC reset [40251.703334] ath: Chip reset failed [40251.703335] ath: Unable to reset hardware; reset status -22 This is currently only reproducible with some HB92 (Half Mini-PCIE) cards but the fix applies to all AR9280 cards. This patch fixes this issue by setting bit 22 during radio disable. This patch has fixes for all kernels that has ath9k. [1] http://wireless.kernel.org/en/developers/Testing/wifi-test Cc: kyungwan.nam@atheros.com Cc: amod.bodas@atheros.com Cc: david.quan@atheros.com Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08libertas: terminate scan when stopping interfaceDaniel Drake
There are currently no provisions in place to ensure that the scanning task has been stopped when the interface is stopped or removed. This can result in a WARNING at net/wireless/core.c:643 and other badness when you remove the module while a scan is happening. Terminate the scanning task during interface stop. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08mac80211: unset SDATA_STATE_OFFCHANNEL when cancelling a scanBrian Cavagnolo
For client STA interfaces, ieee80211_do_stop unsets the relevant interface's SDATA_STATE_RUNNING state bit prior to cancelling an interrupted scan. When ieee80211_offchannel_return is invoked as part of cancelling the scan, it doesn't bother unsetting the SDATA_STATE_OFFCHANNEL bit because it sees that the interface is down. Normally this doesn't matter because when the client STA interface is brought back up, it will probably issue a scan. But in some cases (e.g., the user changes the interface type while it is down), the SDATA_STATE_OFFCHANNEL bit will remain set. This prevents the interface queues from being started. So we cancel the scan before unsetting the SDATA_STATE_RUNNING bit. Signed-off-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08ath9k: check old power mode before clearing cycle countersFelix Fietkau
ath9k_ps_wakeup() clears the cycle counters after waking up the hardware using ath9k_hw_setpower, however if power save is disabled, then the counters will contain useful data, which then gets discarded. Fix this by checking the old power mode before discarding any data. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08cfg80211: fix a crash in dev lookup on dump commandsFelix Fietkau
IS_ERR and PTR_ERR were called with the wrong pointer, leading to a crash when cfg80211_get_dev_from_ifindex fails. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08carl9170: usbid table updatesChristian Lamparter
This patch includes the following updates: * add D-Link DWA-130 Rev D * Netgear has three WNDA3100 versions. the original WNDA3100 is now called WNDA3100v1. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08ath9k: Fix a DMA latency issue for Intel Pinetrail platforms.Vivek Natarajan
Throughput was severely affected in Intel Pinetrail platforms because of a DMA problem in C3 state. This patch fixes this issue. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> CC: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08ath9k: Avoid HW opmode overridden on monitor mode changesRajkumar Manoharan
The HW opmode is blindly set to monitor type on monitor mode change notification. This overrides the opmode when one of the interfaces is still running as non-monitor iftype. So the monitoring information needs to be maintained seperately. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08libipw: fix proc entry removalLinus Torvalds
This bug seems to be due to commit 27ae60f8f7aac ("ipw2x00: replace "ieee80211" with "libipw" where appropriate"), where Pavel did this: - libipw_proc = proc_mkdir(DRV_NAME, init_net.proc_net); + libipw_proc = proc_mkdir("ieee80211", init_net.proc_net); but then the cleanup was kept as remove_proc_entry(DRV_NAME, init_net.proc_net); in both places (both in the failure case and in the unload case). The error string is also total crap, and says "Unable to create " DRV_NAME " proc directory\n"); Even though it doesn't actually create a proc directory named DRV_NAME at all. So that patch looks like total and utter crap to me. The commit message says "Keep /proc/net/ieee80211 under the original name to avoid breaking user interface." but the thing is, it really didn't fix anything but that one create thing. It needs to fix all the other cases too. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-29b43: Fix warning at drivers/mmc/core/core.c:237 in mmc_wait_for_cmdLarry Finger
On module removal, the sdio version of b43 generates the following warning: [ 851.560519] ------------[ cut here ]------------ [ 851.560531] WARNING: at drivers/mmc/core/core.c:237 mmc_wait_for_cmd+0x88/0x90() [ 851.560534] Hardware name: 20552PG [ 851.560536] Modules linked in: b43(-) ssb mmc_block binfmt_misc rfcomm sco bnep ppdev l2cap ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp kvm_intel kvm arc4 iwlagn snd_hda_codec_conexant snd_hda_intel snd_hda_codec iwlcore snd_hwdep snd_pcm thinkpad_acpi mac80211 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq r852 joydev snd_timer sm_common pcmcia nand snd_seq_device cfg80211 sdhci_pci btusb psmouse tpm_tis yenta_socket nand_ids lp snd pcmcia_rsrc nand_ecc bluetooth sdhci tpm pcmcia_core parport mtd snd_page_alloc serio_raw tpm_bios soundcore nvram led_class sha256_generic aes_i586 aes_generic dm_crypt i915 drm_kms_helper drm ahci intel_agp i2c_algo_bit intel_gtt e1000e libahci video agpgart output [ 851.560620] Pid: 2504, comm: rmmod Not tainted 2.6.36-titan0+ #1 [ 851.560622] Call Trace: [ 851.560631] [<c014a102>] warn_slowpath_common+0x72/0xa0 [ 851.560636] [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90 [ 851.560641] [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90 [ 851.560645] [<c014a152>] warn_slowpath_null+0x22/0x30 [ 851.560649] [<c04d94c8>] mmc_wait_for_cmd+0x88/0x90 [ 851.560655] [<c0401585>] ? device_release+0x25/0x80 [ 851.560660] [<c04df210>] mmc_io_rw_direct_host+0xa0/0x150 [ 851.560665] [<c04df370>] mmc_io_rw_direct+0x30/0x40 [ 851.560669] [<c04e06e7>] sdio_disable_func+0x37/0xa0 [ 851.560683] [<f8dfcb80>] b43_sdio_remove+0x30/0x50 [b43] [ 851.560687] [<c04df8cc>] sdio_bus_remove+0x1c/0x60 [ 851.560692] [<c016d39f>] ? blocking_notifier_call_chain+0x1f/0x30 [ 851.560697] [<c0404991>] __device_release_driver+0x51/0xb0 [ 851.560701] [<c0404a7f>] driver_detach+0x8f/0xa0 [ 851.560705] [<c0403c83>] bus_remove_driver+0x63/0xa0 [ 851.560709] [<c0405039>] driver_unregister+0x49/0x80 [ 851.560713] [<c0405039>] ? driver_unregister+0x49/0x80 [ 851.560718] [<c04dfad7>] sdio_unregister_driver+0x17/0x20 [ 851.560727] [<f8dfcb42>] b43_sdio_exit+0x12/0x20 [b43] [ 851.560734] [<f8dfe76f>] b43_exit+0x17/0x3c [b43] [ 851.560740] [<c017fb8d>] sys_delete_module+0x13d/0x200 [ 851.560747] [<c01fd7d2>] ? do_munmap+0x212/0x300 [ 851.560752] [<c010311f>] sysenter_do_call+0x12/0x28 [ 851.560757] ---[ end trace 31e14488072d2f7d ]--- [ 851.560759] ------------[ cut here ]------------ The warning is caused by b43 not claiming the device before calling sdio_disable_func(). Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Arnd Hannemann <arnd@arndnet.de> Tested-by: Arnd Hannemann <arnd@arndnet.de> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-29mac80211: fix failure to check kmalloc return value in key_key_readJesper Juhl
I noticed two small issues in mac80211/debugfs_key.c::key_key_read while reading through the code. Patch below. The key_key_read() function returns ssize_t and the value that's actually returned is the return value of simple_read_from_buffer() which also returns ssize_t, so let's hold the return value in a ssize_t local variable rather than a int one. Also, memory is allocated dynamically with kmalloc() which can fail, but the return value of kmalloc() is not checked, so we may end up operating on a null pointer further on. So check for a NULL return and bail out with -ENOMEM in that case. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-29libertas: Fix sd8686 firmware reloadPaul Fox
For the SD8686, we cannot rely on the scratch register to read the firmware load status, because the same register is used for storing RX packet length. Broaden the check to account for this. The module can now be unloaded/reloaded successfully. Based on the implementation from libertas_tf. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Steve deRosier <steve@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-29ath9k: Fix incorrect access of rate flags in RCMohammed Shafi Shajakhan
The index variable to access the rate flags should be obtained from the inner loop counter which corresponds to the rate table structure.This fixes the invalid rate selection i.e when the supported basic rate is invalid on a particular band and also the following warning message. Thanks to Raj for finding this out. Call Trace: [<ffffffff8104ee4a>] warn_slowpath_common+0x7a/0xb0 [<ffffffff8104ee95>] warn_slowpath_null+0x15/0x20 [<ffffffffa0583c45>] ath_get_rate+0x595/0x5b0 [ath9k] [<ffffffff811a0636>] ? cpumask_next_and+0x36/0x50 [<ffffffffa0405186>] rate_control_get_rate+0x86/0x160 [mac80211] [<ffffffffa040dfac>] invoke_tx_handlers+0x81c/0x12d0 [mac80211] [<ffffffffa040eae9>] ieee80211_tx+0x89/0x2b0 [mac80211] [<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0 [<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211] [<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211] [<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211] [<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150 [mac80211] [<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0 [<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211] [<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211] [<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211] [<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150 [mac80211] [<ffffffffa03f8896>] ieee80211_scan_work+0x146/0x600 [mac80211] [<ffffffff8133a375>] ? schedule+0x2f5/0x8e0 [<ffffffffa03f8750>] ? ieee80211_scan_work+0x0/0x600 [mac80211] [<ffffffff81064fcf>] process_one_work+0x10f/0x380 [<ffffffff81066bc2>] worker_thread+0x162/0x340 [<ffffffff81066a60>] ? worker_thread+0x0/0x340 Cc: stable@kernel.org Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27ath5k: Fix double free on hw attach error pathJones Desougi
If ath5k_hw_attach fails it will free sc->ah (local variable ah) before returning. However, when it reports failure the caller (ath5k_pci_probe) will also free sc->ah. Let the caller handle the deallocation, it does so on further errors as well. Signed-off-by: Jones Desougi <jones.desougi@27m.se> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27mac80211: Fix scan_ies_len to include DS ParamsJouni Malinen
Commit 651b52254fc061f02d965524e71de4333a009a5a added DS Parameter Set information into Probe Request frames that are transmitted on 2.4 GHz band, but it failed to increment local->scan_ies_len to cover this new information. This variable needs to be updated to match the maximum IE data length so that the extra buffer need gets reduced from the driver limit. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27ath9k_htc: Set proper firmware offset for Netgear WNDA3200Rajkumar Manoharan
Netgear WNDA3200 device uses ar7010 firmware but it is failed to set correct firmware offset on firmware download which causes device initialization failure. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27ath9k: fix tx aggregation flush on AR9003Felix Fietkau
Completing aggregate frames can lead to new buffers being pushed into the tid queues due to software retransmission. When the tx queues are being drained, all pending aggregates must be completed before the tid queues get drained, otherwise buffers might be leaked. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27ath9k: lock reset and PCU start/stoppingLuis R. Rodriguez
Apart from locking the start and stop PCU we need to ensure we also content starting and stopping the PCU between hardware resets. This is part of a series that will help resolve the bug: https://bugzilla.kernel.org/show_bug.cgi?id=14624 For more details about this issue refer to: http://marc.info/?l=linux-wireless&m=128629803703756&w=2 Cc: stable@kernel.org Cc: Ben Greear <greearb@candelatech.com> Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27ath9k: rename rxflushlock to pcu_lockLuis R. Rodriguez
The real way to lock RX is to contend on the PCU and reset, this will be fixed in the next patch but for now just do the renames so that the next patch which changes the locking order is crystal clear. This is part of a series that will help resolve the bug: https://bugzilla.kernel.org/show_bug.cgi?id=14624 For more details about this issue refer to: http://marc.info/?l=linux-wireless&m=128629803703756&w=2 Cc: stable@kernel.org Cc: Ben Greear <greearb@candelatech.com> Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27ath9k: add locking for starting the PCU on RXLuis R. Rodriguez
There was some locking for starting some parts of RX but not for starting the PCU. Include this otherwise we can content against stopping the PCU. This can potentially lead to races against different buffers on the PCU which can lead to to the DMA RX engine writing to buffers which are already freed. This is part of a series that will help resolve the bug: https://bugzilla.kernel.org/show_bug.cgi?id=14624 For more details about this issue refer to: http://marc.info/?l=linux-wireless&m=128629803703756&w=2 Cc: stable@kernel.org Cc: Ben Greear <greearb@candelatech.com> Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-27ath9k: add locking for stopping RXLuis R. Rodriguez
ath9k locks for starting RX but not for stopping RX. We could potentially run into a situation where tried to stop RX but immediately started RX. This allows for races on the the RX engine deciding what buffer we last left off on and could potentially cause ath9k to DMA into already free'd memory or in the worst case at a later time to already given memory to other drivers. Fix this by locking stopping RX. This is part of a series that will help resolve the bug: https://bugzilla.kernel.org/show_bug.cgi?id=14624 For more details about this issue refer to: http://marc.info/?l=linux-wireless&m=128629803703756&w=2 Cc: stable@kernel.org Cc: Ben Greear <greearb@candelatech.com> Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-16 06:52:59 +0000