summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-01-07[media] Documentation/DocBook/media/v4l/subdev-formats.xml: fix a typoAntonio Ospite
The xref to the v4l2-mbus-pixelcode-yuv8 table gets rendered as "Table 4.22, “YUV Formats”", so use the verb in the third person singular because it refers to "Table": s/list/lists/ Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] cx231xx: fix i2c debug printsMatthias Schwarzott
Do not shift the already 7bit i2c address. Print a message also for write+read transactions. For write+read, print the read buffer correctly instead of using the write buffer. Signed-off-by: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] cx231xx: Add missing selects for MEDIA_SUBDRV_AUTOSELECTMatthias Schwarzott
The two drivers LGDT3305 and TDA18271C2DD were not autoselected, so the cx231xx_dvb module could not be loaded when MEDIA_SUBDRV_AUTOSELECT=y. Signed-off-by: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] radio-bcm2048: fix missing unlock on error in bcm2048_rds_fifo_receive()Wei Yongjun
Add the missing unlock before return from function bcm2048_rds_fifo_receive() in the error handling case. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: add drive strength enum and sync names with adv7604Hans Verkuil
Add a proper driver strength enum and use the same names in the platform data as with adv7604. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: initialize timings to CEA 640x480p59.94Hans Verkuil
This timing must be supported by all HDMI equipment, so that's a reasonable default. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: set LLC DLL phase from platform_dataHans Verkuil
The correct LLC DLL phase depends on the board layout, so this should be part of the platform_data. Also updated the platform_data in ezkit to ensure that what was the old default value is now explicitly specified, so the behavior for that board is unchanged. Tested-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: return 0 if no change in s_dv_timingsMartin Bugge
Return 0 if the new timings are equal to the current timings as it caused extra cp-loss/lock interrupts. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: Composite sync adjustmentMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: obtain free-run mode from the platform_dataMartin Bugge
The free-run mode can be board-specific. Also updated the platform_data in ezkit to ensure that what was the old default value is now explicitly specified, so the behavior for that board is unchanged. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: composite sd-ram test, clear timings before settingMartin Bugge
Must clear timings before setting after test to recover. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: enable HDMI/DVI mode irqMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: i2c dummy clients registrationMartin Bugge
Clear i2c_clients ptr when unregistered. Warn if configured i2c-addr is zero. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: support g_edid ioctlMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: restart STDI once if format is not foundMartin Bugge
The STDI block may measure wrong values, especially for lcvs and lcf. If the driver can not find any valid timing, the STDI block is restarted to measure the video timings again. The function will return an error, but the restart of STDI will generate a new STDI interrupt and the format detection process will restart. Copied from adv7604. Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: clear edid, if no edid just disable Edid-DDC accessMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: mute audio before switching inputs to avoid noise/popsMats Randgaard
Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: Use defines to select EDID portMats Randgaard
Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: remove connector type. Never used for anything usefulMats Randgaard
May also be wrong if the receiver is connected to more than one connector. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: increase wait timeMartin Bugge
Wait 5ms after main reset. The data-sheet doesn't specify the wait after i2c-controlled reset, so using same value as after pin-controlled reset. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: set default input in platform-dataMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: 625/525 line standard jitter fixMartin Bugge
Both the PAL and NTSC standards are interlaced where a frame consist of two fields. Total number of lines in a frame in both systems are an odd number so the two fields will have different length. In the 625 line standard ("PAL") the odd field of the frame is transmitted first, while in the 525 standard ("NTSC") the even field is transmitted first. This adds the possibility to change output config between the fields and standards. This setting will reduce the "format-jitter" on the signal sent by the pixelport moving the difference between the fields to vertical front/back-porch only. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: set defaults spa-locationMartin Bugge
For edid with no Source Physical Address (spa), set spa-location to default and use correct values from edid. Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: support YCrCb analog input, receive CEA formats as RGB on ↵Hans Verkuil
VGA input Added support for YCrCb analog input. If input is ADV7842_MODE_RGB and RGB quantization range is set to V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected. See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011" for details. Make sure that when switching inputs the RGB quantization range is updated as well. Also updated the platform_data in ezkit to ensure that what was the old default value is now explicitly specified, so the behavior for that board is unchanged. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: added DE vertical position in SDP-io-syncMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: save platform data in state structMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: properly enable/disable the irqsMartin Bugge
The method of disabling the irq-output pin caused many "empty" interrupts. Instead, actually disable/enable the interrupts by changing the interrupt masks. Also enable STORE_MASKED_IRQ in INT1 configuration, otherwise when HDMI events happen while the interrupt is masked those events will be ignored when the interrupt is unmasked. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: corrected setting of cp-register 0x91 and 0x8fMartin Bugge
Bit 6 of register 0x8f was cleared incorrectly (must be 1), and bit 4 of register 0x91 was set incorrectly (must be 0). These bits are undocumented, so we shouldn't modify them to values different from what the datasheet specifies. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: Re-worked query_dv_timings()Martin Bugge
This simplified the code quite a bit. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: initialize timings to CEA 640x480p59.94Hans Verkuil
This timing must be supported by all HDMI equipment, so that's a reasonable default. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: sync polarities from platform dataMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: return immediately if the new timings are equal to what is ↵Mats Randgaard
configured Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: Enable HDMI_MODE interruptMats Randgaard
Some sources are initially detected as DVI, and change to HDMI later. This must be detected to set the right RGB quantization range. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: adjust gain and offset for DVI-D signalsMats Randgaard
If the input signal is DVI-D and quantization range is RGB full range, gain and offset must be adjusted to get the right range on the output. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: set restart_stdi_once flag when signal is lostMartin Bugge
If the restart_stdi_once trick fails to find a valid format the flag was never reset. Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: improve HDMI audio handlingMats Randgaard
- Mute audio before switching inputs to avoid noise/pops - Mute audio if audio FIFO over-/underflows (AD Recommended setting) - Reset FIFO if it over-/underflows (AD Recommended setting) Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: remove debouncing of ADV7604_FMT_CHANGE eventsMats Randgaard
ADV7604_FMT_CHANGE events was debounced in adv7604_isr() to avoid that a receiver with a unstable input signal would block the event handling for other inputs. This solution was prone to errors. A better protection agains interrupt blocking is to delay the call of the interrupt service routine in the adv7604 driver if too many interrupts are received within a given time. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: return immediately if the new input is equal to what is ↵Mats Randgaard
configured Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: remove connector type. Never used for anything usefulMats Randgaard
May also be wrong if the receiver is connected to more than one connector. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: improve EDID handlingMats Randgaard
- split edid_write_block() - do not use edid->edid before the validity check - Return -EINVAL if edid->pad is invalid - Save both registers for SPA port A - Set SPA location to default value if it is not found Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: set CEC address (SPA) in EDIDMats Randgaard
Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: select YPbPr if RGB_RANGE_FULL/LIMITED is set for VGA_COMP ↵Mats Randgaard
inputs Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: Receive CEA formats as RGB on VGA (RGB) inputMats Randgaard
If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode will be selected. See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010" for details. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: adv7604_s_register clean upHans Verkuil
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: support 1366x768 DMT Reduced BlankingMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: add hdmi driver strength adjustmentMikhail Khelik
The driver strength is board dependent, so set it from the platform_data. Signed-off-by: Mikhail Khelik <mkhelik@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: add support for all the digital input portsMats Randgaard
The adv7604 supports four digital input ports. This patch adds support for all of them, instead of just port A. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7511: verify EDID headerMartin Bugge
Ignore EDID's where the header is wrong. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7511: add VIC and audio CTS/N values to log_statusMartin Bugge
Improve status logging. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7511: disable register reset by HPDMartin Bugge
Whenever the hotplug pin is pulled low the chip resets a whole bunch of registers. It turns out that this can be turned off on the adv7511. Do so, as this 'feature' introduces race conditions in setting up registers, particular when the hotplug pin bounces a lot. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-17 13:29:55 +0000