| Age | Commit message (Collapse) | Author |
|---|
|
This patch converts the au1000-eth driver to become a full platform-driver
as it ought to be. We now pass PHY-speficic configurations through
platform_data but for compatibility the driver still assumes the default
settings (search for PHY1 on MAC0) when no platform_data is passed. Tested
on my MTX-1 board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/619/
Patchwork: http://patchwork.linux-mips.org/patch/963/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch makes the board code register the au1000-eth platform device. The
au1000-eth platform data can be overriden with the au1xxx_override_eth_cfg
function like it has to be done for the Bosporus board which uses a
different MAC/PHY setup.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: David Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/618/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Machine driver for DB1200 AC97 and I2S audio systems, intended as a proper
reference asoc machine for Alchemy-based systems. AC97/I2S can be selected
at boot time by setting switch S6.7.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: alsa-devel@alsa-project.org
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Create own directory for DB1200 code and update it with new features.
- SPI support:
- tmp121 temperature sensor
- SPI flash on DB1200
- I2C support
- NE1619 sensor
- AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Replace the devboard NOR MTD mapping driver with physmap-flash support.
Also honor the "swapboot" switch settings wrt. to the layout of the
NOR partitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Limit the amount of address space claimed for Alchemy serial ports to
0x1000. On the Au1300, ports are only 0x1000 apart, and the registers
only extend to 0x110 at most on all supported alchemy models.
On the Au1300 the autodetect logic no longer works and this makes it
necessary to specify the port type through platform data. Because of
this the MSR quirk needs to be moved outside the autoconfig() function
which will no longer be called when UPF_FIXED_TYPE is specified.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
UART autodetection breaks on the Au1300 but the IP blocks are identical,
at least according to the datasheets. Help the 8250 driver by passing
on uart type information via platform data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Warnings being suppressed, we can now turn on -Werror for boards which did
not have it already (devboards and xss1500).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch fixes warnings due to potentially unused
variables in board setup code or mixed variables
declaration and code (forbidden by ISO C90).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Nothing in-tree uses it, so get rid of it.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove unused uart bit definitions and base macros.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions: The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.
So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
By replacing an extra do_IRQ with a goto, the assembly shrinks
from 260 to 212 bytes (gcc-4.3.4).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Eliminate the sharing of IRQ names among the differenct Alchemy
variants. IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.
This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!
Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Extract the alchemy chip variant from c0_prid register.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/14/
Patchwork: http://patchwork.linux-mips.org/patch/707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Raise RTCMATCH2 interrupt priority in case it is used as the system
timer tick.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The Alchemy hardware provides a method to prioritize interrupts
on a controller by assigning them to a differenct core request line.
Assign usb device request interrupt to IC0 Request 0 (which has
highest priority in the core and the dispatcher) and others to
Request 1. The explicit check for usb device request occurrence
should be obsolete now.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Rewritten XXS1500 PCMCIA socket driver, standalone (doesn't depend on
au1000_generic.c) and added carddetect IRQ support.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Move the PB1200 IRQ cascade code out to the BCSR support code:
upcoming DB1300 support can use it too.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Seen on rm200_defconfig for example:
CC arch/mips/boot/compressed/decompress.o
/home/ralf/src/linux/upstream-linus/arch/mips/boot/compressed/decompress.c: In function ‘decompress_kernel’:
/home/ralf/src/linux/upstream-linus/arch/mips/boot/compressed/decompress.c:116: error: implicit declaration of function ‘decompress’
make[3]: *** [arch/mips/boot/compressed/decompress.o] Error 1
make[2]: *** [vmlinuz.ecoff] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Hibernate: Fix preallocating of memory
PM / Hibernate: Remove swsusp.c finally
PM / Hibernate: Remove trailing space in message
PM: Allow SCSI devices to suspend/resume asynchronously
PM: Allow USB devices to suspend/resume asynchronously
USB: implement non-tree resume ordering constraints for PCI host controllers
PM: Allow PCI devices to suspend/resume asynchronously
PM / Hibernate: Swap, remove useless check from swsusp_read()
PM / Hibernate: Really deprecate deprecated user ioctls
PM: Allow device drivers to use dpm_wait()
PM: Start asynchronous resume threads upfront
PM: Add facility for advanced testing of async suspend/resume
PM: Add a switch for disabling/enabling asynchronous suspend/resume
PM: Asynchronous suspend and resume of devices
PM: Add parent information to timing messages
PM: Document device power attributes in sysfs
PM / Runtime: Add sysfs switch for disabling device run-time PM
|
|
There's currently an open Ubuntu bug[0], with the intent to compile NFS_FSCACHE
(and possibly AFS_FSCACHE, 9P_FSCACHE) into the standard Ubuntu kernel.
However, since *_FSCACHE still depends on EXPERIMENTAL, this won't happen.
As Arjan van de Ven pointed out[1], the EXPERIMENTAL flag doesn't mean that
much any more, I propose the following patch to fs/nfs/Kconfig. I'd do the
same for fs/9p/Kconfig and fs/afs/Kconfig, but as I did not test 9p or AFS, I
feel it would not be appropriate for me to remove the flag.
[0] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/440522/comments/5
[1] http://lkml.org/lkml/2010/1/23/145
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
toshiba_acpi: Add full hotkey support
hp-wmi: Add support for tablet rotation key
dell-laptop: Add another Dell laptop to the DMI whitelist
classmate-laptop: use a single MODULE_DEVICE_TABLE to get correct aliases
dell-laptop: Pay attention to which devices the hardware switch controls
dell-laptop: Use buffer with 32-bit physical address
dell-laptop: Blacklist machines not supporting dell-laptop
dell-laptop: Block software state changes when rfkill hard blocked
dell-laptop: Fix small memory leak
dell-laptop: Fix platform device unregistration
dell-laptop: Update rfkill state on kill switch
compal-laptop: Replace sysfs support with rfkill support
compal-laptop: Add support for known Compal made Dell laptops
MAINTAINERS: update drivers/platform/x86 information
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use bastmode in debugfs output
dlm: Send lockspace name with uevents
dlm: send reply before bast
dlm: fix ordering of bast and cast
|
|
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (52 commits)
fs/xfs: Correct NULL test
xfs: optimize log flushing in xfs_fsync
xfs: only clear the suid bit once in xfs_write
xfs: kill xfs_bawrite
xfs: log changed inodes instead of writing them synchronously
xfs: remove invalid barrier optimization from xfs_fsync
xfs: kill the unused XFS_QMOPT_* flush flags V2
xfs: Use delay write promotion for dquot flushing
xfs: Sort delayed write buffers before dispatch
xfs: Don't issue buffer IO direct from AIL push V2
xfs: Use delayed write for inodes rather than async V2
xfs: Make inode reclaim states explicit
xfs: more reserved blocks fixups
xfs: turn off sign warnings
xfs: don't hold onto reserved blocks on remount,ro
xfs: quota limit statvfs available blocks
xfs: replace KM_LARGE with explicit vmalloc use
xfs: cleanup up xfs_log_force calling conventions
xfs: kill XLOG_VEC_SET_TYPE
xfs: remove duplicate buffer flags
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6
* 'ibft-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6:
ibft: Update MAINTAINERS file.
drivers/firmware/iscsi_ibft.c: remove NIPQUAD_FMT, use %pI4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...
|
|
invalid Payload Pointer
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
has a bug that causes endless loop when Payload Pointer of MPEG2-TS
frame is 182 or 183. Anyone who sends malicious MPEG2-TS frame will
cause the receiver of ULE SNDU to go into endless loop.
This patch was generated and tested against linux-2.6.32.9 and should
apply cleanly to linux-2.6.33 as well because there was only one typo
fix to dvb_net.c since v2.6.32.
This bug was brought to you by modern day Santa Claus who decided to
shower the satellite dish at Keio University with heavy snow causing
huge burst of errors. We, receiver end, received Santa Claus's gift in
the form of kernel bug.
Care has been taken not to introduce more bug by fixing this bug, but
please scrutinize the code for I always produces buggy code.
Signed-off-by: Ang Way Chuang <wcang79@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'kmemcheck-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
kmemcheck: Test the full object in kmemcheck_is_obj_initialized()
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/xfs-vipt:
xfs: fix xfs to work with Virtually Indexed architectures
sh: add mm API for DMA to vmalloc/vmap areas
arm: add mm API for DMA to vmalloc/vmap areas
parisc: add mm API for DMA to vmalloc/vmap areas
mm: add coherence API for DMA to vmalloc/vmap areas
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (158 commits)
[SCSI] Fix printing of failed 32-byte commands
[SCSI] Fix printing of variable length commands
[SCSI] libsrp: fix bug in ADDITIONAL CDB LENGTH interpretation
[SCSI] scsi_dh_alua: Add IBM Power Virtual SCSI ALUA device to dev list
[SCSI] scsi_dh_alua: add netapp to dev list
[SCSI] qla2xxx: Update version number to 8.03.02-k1.
[SCSI] qla2xxx: EEH: Restore PCI saved state during pci slot reset.
[SCSI] qla2xxx: Add firmware ETS burst support.
[SCSI] qla2xxx: Correct loop-resync issues during SNS scans.
[SCSI] qla2xxx: Correct use-after-free issue in terminate_rport_io callback.
[SCSI] qla2xxx: Correct EH bus-reset handling.
[SCSI] qla2xxx: Proper clean-up of BSG requests when request times out.
[SCSI] qla2xxx: Initialize payload receive length in failure path of vendor commands
[SCSI] fix duplicate removal on error path in scsi_sysfs_add_sdev
[SCSI] fix refcounting bug in scsi_get_host_dev
[SCSI] fix memory leak in scsi_report_lun_scan
[SCSI] lpfc: correct PPC build failure
[SCSI] raid_class: add raid1e
[SCSI] mpt2sas: Do not call sas_is_tlr_enabled for RAID volumes.
[SCSI] zfcp: Introduce header file for qdio structs and inline functions
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (31 commits)
crypto: aes_generic - Fix checkpatch errors
crypto: fcrypt - Fix checkpatch errors
crypto: ecb - Fix checkpatch errors
crypto: des_generic - Fix checkpatch errors
crypto: deflate - Fix checkpatch errors
crypto: crypto_null - Fix checkpatch errors
crypto: cipher - Fix checkpatch errors
crypto: crc32 - Fix checkpatch errors
crypto: compress - Fix checkpatch errors
crypto: cast6 - Fix checkpatch errors
crypto: cast5 - Fix checkpatch errors
crypto: camellia - Fix checkpatch errors
crypto: authenc - Fix checkpatch errors
crypto: api - Fix checkpatch errors
crypto: anubis - Fix checkpatch errors
crypto: algapi - Fix checkpatch errors
crypto: blowfish - Fix checkpatch errors
crypto: aead - Fix checkpatch errors
crypto: ablkcipher - Fix checkpatch errors
crypto: pcrypt - call the complete function on error
...
|
|
Provide the right e-mail and names for me and Peter.
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
|
|
Convert netmask to __be32 and format it with %pI4
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Konrad Rzeszutek <ketuzsezr@darnok.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
|
|
The hibernate memory preallocation code allocates memory to push some
user space data out of physical RAM, so that the hibernation image is
not too large. It allocates more memory than necessary for creating
the image, so it has to release some pages to make room for
allocations made while suspending devices and disabling nonboot CPUs,
or the system will hang due to the lack of free pages to allocate
from. Unfortunately, the function used for freeing these pages,
free_unnecessary_pages(), contains a bug that prevents it from doing
the job on all systems without highmem.
Fix this problem, which is a regression from the 2.6.30 kernel, by
using the right condition for the termination of the loop in
free_unnecessary_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Cc: stable@kernel.org
|
|
Its contents and entry in Makefile were already removed in
8e60c6a1348e17e68ad73589a52a03876e7059be
(Shift remaining code from swsusp.c to hibernate.c)
but somehow it remained in-place (rjw: which most likely was my
mistake).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Remove a trailing space from a message in swsusp_save().
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Set power.async_suspend for all SCSI devices, targets and hosts, so
that they can be suspended and resumed in parallel with the main
suspend/resume thread and possibly with other devices they don't
depend on in a known way (i.e. devices which are not their parents or
children).
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
