| Age | Commit message (Collapse) | Author |
|---|
|
Commit be639ac6 ("NET: AX.25: Check ioctl arguments to avoid overflows
further down the road") rejects very large arguments, but doesn't
completely fix overflows on 64-bit systems. Consider the AX25_T2 case.
int opt;
...
if (opt < 1 || opt > ULONG_MAX / HZ) {
res = -EINVAL;
break;
}
ax25->t2 = opt * HZ;
The 32-bit multiplication opt * HZ would overflow before being assigned
to 64-bit ax25->t2. This patch changes "opt" to unsigned long.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When testing L2TP support, I discovered that the l2tp module is not autoloaded
as are other netlink interfaces. There is because of lack of hook in genetlink to call
request_module and load the module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The route we have here is for the address being added to the interface,
ie. for input packet processing.
Therefore using that route to determine whether an output nexthop gateway
is known and resolved doesn't make any sense.
So, simply remove this test, it never triggered anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
|
|
|
|
On extensive NFS boots on a mx6qsabrelite board it was noted that "FEC: MDIO read timeout" were occuring,
which caused failure on loading the FEC driver.
The original FEC_MII_TIMEOUT was set to 1 ms, which is too low when passed to the usecs_to_jiffies macro.
On ARM one jiffy is 10ms, so use a timeout of 30ms, which corresponds to 3 jiffies.
After running extensive NFS boots, the MDIO timeouts do not occur anymore with this change.
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using /proc/net/nf_conntrack has been deprecated in favour of the
conntrack(8) tool.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
One simplification of an if clause.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
References: http://www.spinics.net/lists/netfilter-devel/msg18875.html
Augment xt_ecn by facilities to match on IPv6 packets' DSCP/TOS field
similar to how it is already done for the IPv4 packet field.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use the new macro and struct names in xt_ecn.h, and put the old
definitions into a definition-forwarding ipt_ecn.h.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Prepare the ECN match for augmentation by an IPv6 counterpart. Since
no symbol dependencies to ipv6.ko are added, having a single ecn match
module is the more so welcome.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
SGI IP32 (O2)'s ethernet driver (meth) lacks a set_rx_mode function, which
prevents IPv6 from working completely because any ICMPv6 neighbor
solicitation requests aren't picked up by the driver. So the machine can
ping out and connect to other systems, but other systems will have a very
hard time connecting to the O2.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix allyesconfig build on architectures without IOMEM:
drivers/net/ethernet/calxeda/xgmac.c:1800:2:
error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Migrates the buf_seqno() helper routine from broadcast link level to
unicast link level so that it can be used both types of TIPC links.
This is a cosmetic change only, and does not affect the operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adds checks to TIPC's broadcast link so that it ignores any
acknowledgement message containing a sequence number that does not
correspond to an unacknowledged message currently in the broadcast
link's transmit queue.
This change prevents the broadcast link from becoming stalled if a
newly booted node receives stale broadcast link acknowledgement
information from another node that has not yet fully synchronized
its end of the broadcast link to reflect the current state of the
new node's end.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adds code to release any unsent broadcast messages in the broadcast link
transmit queue if TIPC loses contact with its only neighboring node.
Previously, a broadcast link that was in the congested state would hold
on to the unsent messages, even though the messages were now undeliverable.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The two broadcast link statistics fields that are used to derive the
average length of that link's transmit queue are now updated only after
a successful attempt to send a broadcast message, since there is no need
to update these values when an unsuccessful send attempt leaves the
queue unchanged.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adds a check to detect when an attempt is made to send a message
via the broadcast link and no neighboring nodes are currently available
to receive it. Rather than wasting effort passing the message to the
broadcast link and broadcast bearer, who will only throw it away,
TIPC now frees the message immediately and reports success (i.e. the
message has been delivered to all available destinations).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Fixes oversight that allowed broadcast link node map to be updated without
first taking the broadcast link spinlock that protects the map. As part
of this fix the node map has been incorporated into the broadcast link
structure to make the need for such protection more evident.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Creates global variables to hold the broadcast link's pseudo-bearer and
pseudo-link structures, rather than allocating them dynamically. There
is only a single instance of each structure, and changing over to static
allocation allows elimination of code to handle the cases where dynamic
allocation was unsuccessful.
The memset in the teardown code may look like they aren't used, but
the same teardown code is run when there is a non-fatal error at
init-time, so that stale data isn't present when the user fixes the
cause of the soft error.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Gets rid of an unnecessary check in the routine that updates the port id
of a node's name publications when the node is assigned a network address,
since the routine is only invoked if the new address is different from
the existing one.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies TIPC's module unloading logic to switch itself into "single
node" mode before starting to terminate networking support. This helps
to ensure that no operations that require TIPC to be in "networking"
mode can initiate once unloading starts.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Gets rid of two pointless operations that zero out the array used to
record information about TIPC's Ethernet bearers. There is no need to
initialize the array on start up since it is a global variable that is
already zero'd out, and there is no need to zero it out on exit because
the array is never referenced again.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies Ethernet bearer disable logic to break the association between
the bearer and its device driver at the time the bearer is disabled,
rather than when the TIPC module is unloaded. This allows the array
entry used by the disabled bearer to be re-used if the same bearer (or
a different one) is subsequently enabled.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Change TIPC's shutdown code to deactivate generic networking support
before terminating Ethernet media support. The deactivation of generic
networking support causes all existing bearers to be destroyed, meaning
the Ethernet media termination routine no longer has to bother marking
them as unavailable.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Comment-only change to better explain why TIPC's configuration lock is
temporarily released while activating support for network interfaces,
and why the existing activation code doesn't require rework.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Permits run-time alteration of default link settings on a per-media
and per-bearer basis, in addition to the existing per-link basis.
The following syntax can now be used:
tipc-config -lt=<link-name|bearer-name|media-name>/<tolerance>
tipc-config -lp=<link-name|bearer-name|media-name>/<priority>
tipc-config -lw=<link-name|bearer-name|media-name>/<window>
Note that changes to the default settings for a given media type has
no effect on the default settings used by existing bearers. Similarly,
changes to default bearer settings has no effect on existing link
endpoints that utilize that interface.
Thanks to Florian Westphal <fw@strlen.de> for his contributions to
the development of this enhancement.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adds a check to ensure that TIPC ignores an incoming neighbor discovery
message that specifies an invalid media address as its source. The check
ensures that the source address is a valid, non-broadcast address that
could legally be used by a neighboring link endpoint.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Reworks TIPC's media address data structure and associated processing
routines to transfer all media-specific details of address conversion
to the associated TIPC media adaptation code. TIPC's generic bearer code
now only needs to know which media type an address is associated with
and whether or not it is a broadcast address, and totally ignores the
"value" field that contains the actual media-specific addressing info.
These changes eliminate the need for a number of endianness conversion
operations and will make it easier for TIPC to support new media types
in the future.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Enhances TIPC's Ethernet media support to provide 3 new address conversion
routines, which allow TIPC to interpret an address that is in string form
and to convert an address to and from the 20 byte format used in TIPC's
neighbor discovery messages.
These routines are pre-requisites to a follow on commit that hides all
media-specific addressing details from TIPC's generic bearer code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Enhances conversion of a media address to printable form so that an
unconvertable address will be displayed as a string of hex digits,
rather than not being displayed at all. (Also removes a pointless check
for the existence of the media-specific address conversion routine,
since the routine is not optional.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Simplifies error handling performed during media registration, since
TIPC no longer supports the dynamic addition of new media types that
are potentially error-prone. These simplifications include the following:
1) No longer check for premature registration of a new media type.
2) No longer check for negative link priority values (which was pointless
since such values are unsigned, and could cause a compiler warning).
3) No longer generate a warning describing the exact cause of any
registration failure (just warns that overall registration failed).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Changes TIPC's list of registered media types from an array of media
structures to an array of pointers to media structures. This eliminates
the need to copy of the contents of the structure passed in during media
registration.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Streamlines the detection of an attempt to register a TIPC media structure
using an already registered name or type identifier. The revised logic now
reuses an existing routine to detect an existing name and no longer
unnecessarily manipulates the media type counter during an unsuccessful
registration attempt.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Speeds up the registration of TIPC media types by passing in a structure
containing the required information, rather than by passing in the various
fields describing the media type individually.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Permits a Linux container to use TIPC sockets even when it has its own
network namespace defined by removing the check that prohibits such use.
This makes it possible for users who wish to isolate their container
network traffic from normal network traffic to utilize TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
v2, based on Jay's review.
I kept the 'link must be up' part, because this is enforced in the code.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RDBG() wasn't even used, and the messages printed by RT6_DEBUG() were
far from useful. Just get rid of all this stuff, we can replace it
with something more suitable if we want.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Include linux/slab.h to fix below build error:
CC drivers/net/ethernet/mellanox/mlx4/resource_tracker.o
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_init_resource_tracker':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:233: error: implicit declaration of function 'kzalloc'
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:234: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_free_resource_tracker':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:264: error: implicit declaration of function 'kfree'
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_qp_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:370: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_mtt_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:386: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_mpt_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:402: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_eq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:417: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_cq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:431: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_srq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:446: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_counter_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:461: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'add_res_range':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:521: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mac_add_to_slave':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:1193: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'add_mcg_res':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:2521: warning: assignment makes pointer from integer without a cast
make[5]: *** [drivers/net/ethernet/mellanox/mlx4/resource_tracker.o] Error 1
make[4]: *** [drivers/net/ethernet/mellanox/mlx4] Error 2
make[3]: *** [drivers/net/ethernet/mellanox] Error 2
make[2]: *** [drivers/net/ethernet] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise we leave uninitialized kernel memory in there.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NLA_PUT macro should accept the actual attribute length, not
the amount of elements in array :(
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This patch adds the match that allows to perform extended
accounting. It requires the new nfnetlink_acct infrastructure.
# iptables -I INPUT -p tcp --sport 80 -m nfacct --nfacct-name http-traffic
# iptables -I OUTPUT -p tcp --dport 80 -m nfacct --nfacct-name http-traffic
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We currently have two ways to account traffic in netfilter:
- iptables chain and rule counters:
# iptables -L -n -v
Chain INPUT (policy DROP 3 packets, 867 bytes)
pkts bytes target prot opt in out source destination
8 1104 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0
- use flow-based accounting provided by ctnetlink:
# conntrack -L
tcp 6 431999 ESTABLISHED src=192.168.1.130 dst=212.106.219.168 sport=58152 dport=80 packets=47 bytes=7654 src=212.106.219.168 dst=192.168.1.130 sport=80 dport=58152 packets=49 bytes=66340 [ASSURED] mark=0 use=1
While trying to display real-time accounting statistics, we require
to pool the kernel periodically to obtain this information. This is
OK if the number of flows is relatively low. However, in case that
the number of flows is huge, we can spend a considerable amount of
cycles to iterate over the list of flows that have been obtained.
Moreover, if we want to obtain the sum of the flow accounting results
that match some criteria, we have to iterate over the whole list of
existing flows, look for matchings and update the counters.
This patch adds the extended accounting infrastructure for
nfnetlink which aims to allow displaying real-time traffic accounting
without the need of complicated and resource-consuming implementation
in user-space. Basically, this new infrastructure allows you to create
accounting objects. One accounting object is composed of packet and
byte counters.
In order to manipulate create accounting objects, you require the
new libnetfilter_acct library. It contains several examples of use:
libnetfilter_acct/examples# ./nfacct-add http-traffic
libnetfilter_acct/examples# ./nfacct-get
http-traffic = { pkts = 000000000000, bytes = 000000000000 };
Then, you can use one of this accounting objects in several iptables
rules using the new nfacct match (which comes in a follow-up patch):
# iptables -I INPUT -p tcp --sport 80 -m nfacct --nfacct-name http-traffic
# iptables -I OUTPUT -p tcp --dport 80 -m nfacct --nfacct-name http-traffic
The idea is simple: if one packet matches the rule, the nfacct match
updates the counters.
Thanks to Patrick McHardy, Eric Dumazet, Changli Gao for reviewing and
providing feedback for this contribution.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Aim of this patch is to provide full range of rps_flow_cnt on 64bit arches.
Theorical limit on number of flows is 2^32
Fix some buggy RPS/RFS macros as well.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
CC: Xi Wang <xi.wang@gmail.com>
CC: Laurent Chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The get and zero operations have to be done in an atomic context,
otherwise counters added between them will be lost.
This problem was spotted by Changli Gao while discussing the
nfacct infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We can't do this without propagating the const to nlk_sk()
too, otherwise:
net/netlink/af_netlink.c: In function ‘netlink_is_kernel’:
net/netlink/af_netlink.c:103:2: warning: passing argument 1 of ‘nlk_sk’ discards ‘const’ qualifier from pointer target type [enabled by default]
net/netlink/af_netlink.c:96:36: note: expected ‘struct sock *’ but argument is of type ‘const struct sock *’
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new netem loss model is configured with nested netlink messages.
This code is being overly strict about sizes, and is easily confused
by padding (or possible future expansion). Also message
for gemodel is incorrect.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add backlog (byte count) information in hfsc classes and qdisc, so that
"tc -s" can report it to user, instead of 0 values :
qdisc hfsc 1: root refcnt 6 default 20
Sent 45141660 bytes 30545 pkt (dropped 0, overlimits 91751 requeues 0)
rate 1492Kbit 126pps backlog 103226b 74p requeues 0
...
class hfsc 1:20 parent 1:1 leaf 1201: rt m1 0bit d 0us m2 400000bit ls m1 0bit d 0us m2 200000bit
Sent 49534912 bytes 33519 pkt (dropped 0, overlimits 0 requeues 0)
backlog 81822b 56p requeues 0
period 23 work 49451576 bytes rtwork 13277552 bytes level 0
...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: John A. Sullivan III <jsullivan@opensourcedevel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently made loopback a bool type instead of an int, so the bitwise
AND is redundent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
