| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fix from Roland Dreier:
"Fix for exploitable integer overflow in uverbs interface"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Prevent integer overflow in ib_umem_get address arithmetic
|
|
xen-netfront limits transmitted skbs to be at most 44 segments in size. However,
GSO permits up to 65536 bytes, which means a maximum of 45 segments of 1448
bytes each. This slight reduction in the size of packets means a slight loss in
efficiency.
Since c/s 9ecd1a75d, xen-netfront sets gso_max_size to
XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER,
where XEN_NETIF_MAX_TX_SIZE is 65535 bytes.
The calculation used by tcp_tso_autosize (and also tcp_xmit_size_goal since c/s
6c09fa09d) in determining when to split an skb into two is
sk->sk_gso_max_size - 1 - MAX_TCP_HEADER.
So the maximum permitted size of an skb is calculated to be
(XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER) - 1 - MAX_TCP_HEADER.
Intuitively, this looks like the wrong formula -- we don't need two TCP headers.
Instead, there is no need to deviate from the default gso_max_size of 65536 as
this already accommodates the size of the header.
Currently, the largest skb transmitted by netfront is 63712 bytes (44 segments
of 1448 bytes each), as observed via tcpdump. This patch makes netfront send
skbs of up to 65160 bytes (45 segments of 1448 bytes each).
Similarly, the maximum allowable mtu does not need to subtract MAX_TCP_HEADER as
it relates to the size of the whole packet, including the header.
Fixes: 9ecd1a75d977 ("xen-netfront: reduce gso_max_size to account for max TCP header")
Signed-off-by: Jonathan Davies <jonathan.davies@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull dmaengine fixes from Vinod Koul:
"This time we have addition of caps for jz4740 which fixes intentional
warning at boot. Then we have memory leak issues in drivers using
virt-dma by Peter on few drive"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: moxart-dma: Fix memory leak when stopping a running transfer
dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer
dmaengine: omap-dma: Fix memory leak when terminating running transfer
dmaengine: edma: fix memory leak when terminating running transfers
dmaengine: jz4740: Define capabilities
|
|
Pull networking fixes from David Miller:
1) Fix use-after-free with mac80211 RX A-MPDU reorder timer, from
Johannes Berg.
2) iwlwifi leaks memory every module load/unload cycles, fix from Larry
Finger.
3) Need to use for_each_netdev_safe() in rtnl_group_changelink()
otherwise we can crash, from WANG Cong.
4) mlx4 driver does register_netdev() too early in the probe sequence,
from Ido Shamay.
5) Don't allow router discovery hop limit to decrease the interface's
hop limit, from D.S. Ljungmark.
6) tx_packets and tx_bytes improperly accounted for certain classes of
USB network devices, fix from Ben Hutchings.
7) ip{6}mr_rules_init() mistakenly use plain kfree to release the ipmr
tables in the error path, they must instead use ip{6}mr_free_table().
Fix from WANG Cong.
8) cxgb4 doesn't properly quiesce all RX activity before unregistering
the netdevice. Fix from Hariprasad Shenai.
9) Fix hash corruptions in ipvlan driver, from Jiri Benc.
10) nla_memcpy(), like a real memcpy, should fully initialize the
destination buffer, even if the source attribute is smaller. Fix
from Jiri Benc.
11) Fix wrong error code returned from iucv_sock_sendmsg(). We should
use whatever sock_alloc_send_skb() put into 'err'. From Eugene
Crosser.
12) Fix slab object leak on module unload in TIPC, from Ying Xue.
13) Need a READ_ONCE() when reading the cached RX socket route in
tcp_v{4,6}_early_demux(). From Michal Kubecek.
14) Still too many problems with TPC support in the ath9k driver, so
disable it for now. From Felix Fietkau.
15) When in AP mode the rtlwifi driver can leak DMA mappings, fix from
Larry Finger.
16) Missing kzalloc() failure check in gs_usb CAN driver, from Colin Ian
King.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
cxgb4: Fix to dump devlog, even if FW is crashed
cxgb4: Firmware macro changes for fw verison 1.13.32.0
bnx2x: Fix kdump when iommu=on
bnx2x: Fix kdump on 4-port device
mac80211: fix RX A-MPDU session reorder timer deletion
MAINTAINERS: Update Intel Wired Ethernet Driver info
tipc: fix a slab object leak
net/usb/r8152: add device id for Lenovo TP USB 3.0 Ethernet
af_iucv: fix AF_IUCV sendmsg() errno
openvswitch: Return vport module ref before destruction
netlink: pad nla_memcpy dest buffer with zeroes
bonding: Bonding Overriding Configuration logic restored.
ipvlan: fix check for IP addresses in control path
ipvlan: do not use rcu operations for address list
ipvlan: protect against concurrent link removal
ipvlan: fix addr hash list corruption
net: fec: setup right value for mdio hold time
net: tcp6: fix double call of tcp_v6_fill_cb()
cxgb4vf: Fix sparse warnings
netns: don't clear nsid too early on removal
...
|
|
Properly verify that the resulting page aligned end address is larger
than both the start address and the length of the memory area requested.
Both the start and length arguments for ib_umem_get are controlled by
the user. A misbehaving user can provide values which will cause an
integer overflow when calculating the page aligned end address.
This overflow can cause also miscalculation of the number of pages
mapped, and additional logic issues.
Addresses: CVE-2014-8159
Cc: <stable@vger.kernel.org>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Some of the CYCLE_ACTIVITY.* events can only be scheduled on
counter 2. Due to a typo Haswell matched those with
INTEL_EVENT_CONSTRAINT, which lead to the events never
matching as the comparison does not expect anything
in the umask too. Fix the typo.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1425925222-32361-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For supporting Intel LBR branches filtering, Intel LBR sharing logic
mechanism is introduced from commit b36817e88630 ("perf/x86: Add Intel
LBR sharing logic"). It modifies __intel_shared_reg_get_constraints() to
config lbr_sel, which is finally used to set LBR_SELECT.
However, the intel_shared_regs_constraints() function is called after
intel_pebs_constraints(). The PEBS event will return immediately after
intel_pebs_constraints(). So it's impossible to filter branches for PEBS
events.
This patch moves intel_shared_regs_constraints() ahead of
intel_pebs_constraints().
We can safely do that because the intel_shared_regs_constraints() function
only returns empty constraint if its rejecting the event, otherwise it
returns NULL such that we continue calling intel_pebs_constraints() and
x86_get_event_constraint().
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1427467105-9260-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We need to wait for all fences, not just the exclusive one.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We somehow try to free the SG table twice.
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=89734
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When performing a modeset, use the framebuffer pitch value to set FIMD
IMG_SIZE and Mixer SPAN registers. These are both defined as pitch - the
distance between contiguous lines (bytes for FIMD, pixels for mixer).
Fixes display on Snow (1366x768).
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch fixes an error in kgdb for x86_64 which would report
the value of dx when asked to give the value of si.
Signed-off-by: Steffen Liebergeld <steffen.liebergeld@kernkonzept.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When I wrote the opportunistic SYSRET code, I missed an important difference
between SYSRET and IRET.
Both instructions are capable of setting EFLAGS.TF, but they behave differently
when doing so:
- IRET will not issue a #DB trap after execution when it sets TF.
This is critical -- otherwise you'd never be able to make forward progress when
returning to userspace.
- SYSRET, on the other hand, will trap with #DB immediately after
returning to CPL3, and the next instruction will never execute.
This breaks anything that opportunistically SYSRETs to a user
context with TF set. For example, running this code with TF set
and a SIGTRAP handler loaded never gets past 'post_nop':
extern unsigned char post_nop[];
asm volatile ("pushfq\n\t"
"popq %%r11\n\t"
"nop\n\t"
"post_nop:"
: : "c" (post_nop) : "r11");
In my defense, I can't find this documented in the AMD or Intel manual.
Fix it by using IRET to restore TF.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 2a23c6b8a9c4 ("x86_64, entry: Use sysret to return to userspace when possible")
Link: http://lkml.kernel.org/r/9472f1ca4c19a38ecda45bba9c91b7168135fcfa.1427923514.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The legcy colorkey ioctls are only implemented for sprite planes, so
reject the ioctl for primary/cursor planes. If we want to support
colorkeying with these planes (assuming we have hw support of course)
we should just move ahead with the colorkey property conversion.
Testcase: kms_legacy_colorkey
Cc: Tommi Rantala <tt.rantala@gmail.com>
Cc: stable@vger.kernel.org
Reference: http://mid.gmane.org/CA+ydwtr+bCo7LJ44JFmUkVRx144UDFgOS+aJTfK6KHtvBDVuAw@mail.gmail.com
Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* fix a memory leak, we leaked memory each time the module
was loaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
cxgb4 FW macro changes for new FW
Fix to dump device log even in the case of firmware crash. Also
incorporates changes for new FW.
This patch series has been created against net tree and includes patches on
cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new Common Code routines to retrieve Firmware Device Log
parameters from PCIE_FW_PF[7]. The firmware initializes its Device Log very
early on and stores the parameters for its location/size in that register.
Using the parameters from the register allows us to access the Firmware
Device Log even when the firmware crashes very early on or we're not
attached to the firmware
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds new macro and few macro changes for fw version 1.13.32.0 also
changes version string in driver to match 1.13.32.0
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This contains just a single fix for a crash I happened to randomly
run into today during testing. It's clearly been around for a while,
but is pretty hard to trigger, even when I tried explicitly (and
modified the code to make it more likely) it rarely did.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"This contains fixes for:
- a VT-d issue where hardware domain-ids might be freed while still
in use.
- an ipmmu-vmsa issue where where the device-table was not zero
terminated
- unchecked register access issue in the arm-smmu driver"
* tag 'iommu-fixes-v4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Remove unused variable
iommu: ipmmu-vmsa: Add terminating entry for ipmmu_of_ids
iommu/vt-d: Detach domain *only* from attached iommus
iommu/arm-smmu: fix ARM_SMMU_FEAT_TRANS_OPS condition
|
|
Since commit 8e7094694396 ("lguest: add a dummy PCI host bridge.")
lguest uses PCI, but it needs you to frob the ports directly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull lazytime fixes from Ted Ts'o:
"This fixes a problem in the lazy time patches, which can cause
frequently updated inods to never have their timestamps updated.
These changes guarantee that no timestamp on disk will be stale by
more than 24 hours"
* tag 'lazytime_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fs: add dirtytime_expire_seconds sysctl
fs: make sure the timestamps for lazytime inodes eventually get written
|
|
Pull nfsd fixes from Bruce Fields:
"Two main issues:
- We found that turning on pNFS by default (when it's configured at
build time) was too aggressive, so we want to switch the default
before the 4.0 release.
- Recent client changes to increase open parallelism uncovered a
serious bug lurking in the server's open code.
Also fix a krb5/selinux regression.
The rest is mainly smaller pNFS fixes"
* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
sunrpc: make debugfs file creation failure non-fatal
nfsd: require an explicit option to enable pNFS
NFSD: Fix bad update of layout in nfsd4_return_file_layout
NFSD: Take care the return value from nfsd4_encode_stateid
NFSD: Printk blocklayout length and offset as format 0x%llx
nfsd: return correct lockowner when there is a race on hash insert
nfsd: return correct openowner when there is a race to put one in the hash
NFSD: Put exports after nfsd4_layout_verify fail
NFSD: Error out when register_shrinker() fail
NFSD: Take care the return value from nfsd4_decode_stateid
NFSD: Check layout type when returning client layouts
NFSD: restore trace event lost in mismerge
|
|
Yuval Mintz says:
====================
bnx2x: kdump related fixes
This patch series aims to fix bnx2x driver issues when loading in kdump kernel.
Both issues fixed here would be fatal to the device, requiring full reset of
the system in order to recover, preventing the device from serving its purpose
in the kdump environment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The ASRock Q1900DC-ITX mainboard (Baytrail-D) hangs randomly in
both BIOS and UEFI mode while rebooting unless reboot=pci is
used. Add a quirk to reboot via the pci method.
The problem is very intermittent and hard to debug, it might succeed
rebooting just fine 40 times in a row - but fails half a dozen times
the next day. It seems to be slightly less common in BIOS CSM mode
than native UEFI (with the CSM disabled), but it does happen in either
mode. Since I've started testing this patch in late january, rebooting
has been 100% reliable.
Most of the time it already hangs during POST, but occasionally it
might even make it through the bootloader and the kernel might even
start booting, but then hangs before the mode switch. The same symptoms
occur with grub-efi, gummiboot and grub-pc, just as well as (at least)
kernel 3.16-3.19 and 4.0-rc6 (I haven't tried older kernels than 3.16).
Upgrading to the most current mainboard firmware of the ASRock
Q1900DC-ITX, version 1.20, does not improve the situation.
( Searching the web seems to suggest that other Bay Trail-D mainboards
might be affected as well. )
--
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: <stable@vger.kernel.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/20150330224427.0fb58e42@mir
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
IIO fixes for 4.0 set 4
A couple more IIO fixes.
* Fix check for HAS_IOMEM in the cc100001_adc driver to avoid build errors.
Rather curiously it was ORed with Regulator and clock support.
* vf610 driver was trying to use an ADC clock outside the possible
spec on some boards. The driver assumed a fixed clock speed previously
across all boards, but that is not true. This fix ensures that the
reported frequency is correct on all boards.
* The adis imu common code directly set the current trigger to the
driver supplied one. Unfortunately this didn't increase the use count
leading to a double free via a particular path of changing the trigger
then removing the driver.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.0-rc6
Here are a few new device IDs.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Coverity reports a warning due to unitialized attr structure in one
code path.
Reported by Coverity (CID 728535)
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Jeff Layton <jlayton@samba.org>
|
|
null tcon is not possible in these paths so
remove confusing null check
Reported by Coverity (CID 728519)
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Jeff Layton <jlayton@samba.org>
|
|
remove impossible check
Pointed out by Coverity (CID 115422)
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Jeff Layton <jlayton@samba.org>
|
|
workstation_RFC1001_name is part of the struct and can't be null,
remove impossible comparison (array vs. null)
Pointed out by Coverity (CID 140095)
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Jeff Layton <jlayton@samba.org>
|
|
Coverity reports a warning for referencing the beginning of the
SMB2/SMB3 frame using the ProtocolId field as an array. Although
it works the same either way, this patch should quiet the warning
and might be a little clearer.
Reported by Coverity (CID 741269)
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@poochiereds.net>
|
|
null tcon is not likely in these paths in current
code, but obviously it does clarify the code to
check for null (if at all) before derefrencing
rather than after.
Reported by Coverity (CID 1042666)
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
|
|
Although unlikely to fail (and tree connect does not commonly send
a password since SECMODE_USER is the default for most servers)
do not ignore errors on SMBNTEncrypt in SMB Tree Connect.
Reported by Coverity (CID 1226853)
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@poochiereds.net>
|
|
Pointed out by coverity analyzer. resp_buftype is
not initialized in one path which can rarely log
a spurious warning (buf is null so there will
not be a problem with freeing data, but if buf_type
were randomly set to wrong value could log a warning)
Reported by Coverity (CID 1269144)
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@poochiereds.net>
|
|
Update the git tree info with a recent change in tree names. Also
add our new mailing list created solely for Linux kernel patches
and kernel development, as well as the new patchwork project for
tracking patches. Lastly update the list of "reviewers" since a
couple of developers have moved on to different projects.
Made an update to the section header so that it is more manageable
going forward as we add new drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When remove TIPC module, there is a warning to remind us that a slab
object is leaked like:
root@localhost:~# rmmod tipc
[ 19.056226] =============================================================================
[ 19.057549] BUG TIPC (Not tainted): Objects remaining in TIPC on kmem_cache_close()
[ 19.058736] -----------------------------------------------------------------------------
[ 19.058736]
[ 19.060287] INFO: Slab 0xffffea0000519a00 objects=23 used=1 fp=0xffff880014668b00 flags=0x100000000004080
[ 19.061915] INFO: Object 0xffff880014668000 @offset=0
[ 19.062717] kmem_cache_destroy TIPC: Slab cache still has objects
This is because the listening socket of TIPC topology server is not
closed before TIPC proto handler is unregistered with proto_unregister().
However, as the socket is closed in tipc_exit_net() which is called by
unregister_pernet_subsys() during unregistering TIPC namespace operation,
the warning can be eliminated if calling unregister_pernet_subsys() is
moved before calling proto_unregister().
Fixes: e05b31f4bf89 ("tipc: make tipc socket support net namespace")
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Space allocated for paca is based off nr_cpu_ids,
but pnv_alloc_idle_core_states() iterates paca with
cpu_nr_cores()*threads_per_core, which is using NR_CPUS.
This causes pnv_alloc_idle_core_states() to write over memory,
which is outside of paca array and may later lead to various panics.
Fixes: 7cba160ad789 (powernv/cpuidle: Redesign idle states management)
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Spell out what this property means to userspace. If the property is set, all
directional axes must be accelerometer axes, any other axes are left as-is.
This allows an accelerometer device to e.g. have an ABS_WHEEL.
It is not permitted to mix normal directional axes and accelerometer axes on
the same device node.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 98dc070373 ("Input: synaptics - add quirk for Thinkpad E440") had
a typo in ymax, this changes the value to the one reported by
touchpad-edge-detector and mentioned in the commit.
Signed-off-by: Filip Ayazi <filipayazi@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending over AF_IUCV socket, errno was incorrectly set to
ENOMEM even when other values where appropriate, notably EAGAIN.
With this patch, error indicator returned by sock_alloc_send_skb()
is passed to the caller, rather than being overwritten with ENOMEM.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return module reference before invoking the respective vport
->destroy() function. This is needed as ovs_vport_del() is not
invoked inside an RCU read side critical section so the kfree
can occur immediately before returning to ovs_vport_del().
Returning the module reference before ->destroy() is safe because
the module unregistration is blocked on ovs_lock which we hold
while destroying the datapath.
Fixes: 62b9c8d0372d ("ovs: Turn vports with dependencies into separate modules")
Reported-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently have a problem that SELinux policy is being enforced when
creating debugfs files. If a debugfs file is created as a side effect of
doing some syscall, then that creation can fail if the SELinux policy
for that process prevents it.
This seems wrong. We don't do that for files under /proc, for instance,
so Bruce has proposed a patch to fix that.
While discussing that patch however, Greg K.H. stated:
"No kernel code should care / fail if a debugfs function fails, so
please fix up the sunrpc code first."
This patch converts all of the sunrpc debugfs setup code to be void
return functins, and the callers to not look for errors from those
functions.
This should allow rpc_clnt and rpc_xprt creation to work, even if the
kernel fails to create debugfs files for some reason.
Symptoms were failing krb5 mounts on systems using gss-proxy and
selinux.
Fixes: 388f0c776781 "sunrpc: add a debugfs rpc_xprt directory..."
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
This is especially important in cases where the kernel allocs a new
structure and expects a field to be set from a netlink attribute. If such
attribute is shorter than expected, the rest of the field is left containing
previous data. When such field is read back by the user space, kernel memory
content is leaked.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit 3900f29021f0bc7fe9815aa32f1a993b7dfdd402 ("bonding: slight
optimizztion for bond_slave_override()") the override logic was to send packets
with non-zero queue_id through the slave with corresponding queue_id, under two
conditions only - if the slave can transmit and it's up.
The above mentioned commit changed this logic by introducing an additional
condition - whether the bond is active (indirectly, using the slave_can_tx and
later - bond_is_active_slave), that prevents the user from implementing more
complex policies according to the Documentation/networking/bonding.txt.
Signed-off-by: Anton Nayshtut <anton@swortex.com>
Signed-off-by: Alexey Bogoslavsky <alexey@swortex.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Benc says:
====================
ipvlan: list corruption and rcu fixes
This patch set fixes different issues leading to corrupted lists and
incorrect rcu usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an ipvlan interface is down, its addresses are not on the hash list.
Fix checks for existence of addresses not to depend on the hash list, walk
through all interface addresses instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
