summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-11-23[media] rc: Add support for decoding Sanyo protocolMauro Carvalho Chehab
This protocol is found on Sanyo/Aiwa remotes. Tested with an Aiwa RC-7AS06 remote control. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-23[media] ir-nec-decoder: Report what bit failed at debug msgMauro Carvalho Chehab
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-21[media] get_dvb_firmware: add support for HVR-930C firmwareEddi De Pieri
Signed-off-by: Eddi De Pieri <eddi@depieri.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-20[media] em28xx: Add IR support for HVR-930CMauro Carvalho Chehab
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-20[media] em28xx: Add IR support for em2884Mauro Carvalho Chehab
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-20[media] em28xx: Fix CodingStyle issues introduced by changeset 82e7dbbMauro Carvalho Chehab
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-20[media] em28xx: initial support for HAUPPAUGE HVR-930C againEddi De Pieri
With this patch I try again to add initial support for HVR930C. Tested only DVB-T, since in Italy Analog service is stopped. Actually "scan -a0 -f1", find only about 50 channel while 400 should be available. [mchehab@redhat.com: Tested with DVB-C and fixed a few whitespace issues] Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Eddi De Pieri <eddi@depieri.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-20[media] xc5000: Add support for get_if_frequencyMauro Carvalho Chehab
This is needed for devices with DRX-K and xc5000. Tested with a HVR 930C hardware. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-16[media] em28xx: Fix some Terratec entries (H5 and XS)Mauro Carvalho Chehab
As reported by Andreas Oberritter <obi@linuxtv.org>, changeset 33ba28eebc3e1758e6adc1fcec9e1e3151bac453 did the wrong thing. Fix it to properly reflect the entries for Terratec H5 revs 1 and 2, and restore Terratec XS entry. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-11[media] Properly implement ITU-T J.88 Annex C supportMauro Carvalho Chehab
The Annex C support were broken with the previous implementation, as, at xc5000 and tda18271c2dd, it were choosing the wrong bandwidth for some symbol rates. At DRX-J, it were always selecting Annex A, even having Annex C support coded there. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-11[media] dvb: Allow select between DVB-C Annex A and Annex CMauro Carvalho Chehab
DVB-C, as defined by ITU-T J.83 has 3 annexes. The differences between Annex A and Annex C is that Annex C uses a subset of the modulation types, and uses a different rolloff factor. A different rolloff means that the bandwidth required is slicely different, and may affect the saw filter configuration at the tuners. Also, some demods have different configurations, depending on using Annex A or Annex C. So, allow userspace to specify it, by changing the rolloff factor. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: add submenu for platform devicesHans Verkuil
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] cx88: fix menu level for the VP-3054 moduleHans Verkuil
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: move all PCI(e) devices to their own submenuHans Verkuil
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: reorganize the radio menuHans Verkuil
Move all USB radio devices to the top of the list and move all ISA devices to a separate menu. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: remove duplicate USB dependencyHans Verkuil
Thanks to Guennadi Liakhovetski <g.liakhovetski@gmx.de> for pointing this out to me. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: move all platform drivers to the bottom of the menuHans Verkuil
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: remove the EXPERIMENTAL tag from vino and c-qcamHans Verkuil
These are really, really old drivers. These are really no longer experimental... Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: move ISA and parport drivers into their own submenuHans Verkuil
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] V4L menu: move USB drivers section to the topHans Verkuil
USB webcams are some of the most used V4L devices, so move it to a more prominent place in the menu instead of being at the end. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] usbvision: Drop broken 10-bit I2C address supportJean Delvare
The support for 10-bit I2C addresses in usbvision seems plain broken to me. I had already noticed that back in February 2007 [1]. The code was not fixed since then, so I take it that it's not actually needed. And as a matter of fact I don't know of any 10-bit addressed I2C tuner, encode, decoder or the like. So let's simply get rid of the broken and useless code. I'm also adding I2C_FUNC_I2C, as the driver and hardware support plain I2C messaging. [1] http://marc.info/?l=linux-i2c&m=117499415208244&w=2 Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] Support for Sveon STV22 (IT9137)Malcolm Priestley
This indeed a clone of Kworld UB499 2T Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Eliminate as10x_handle_t aliasSylwester Nawrocki
Remove pre-processor defined as10x_handle_t data type by directly replacing it with struct as102_bus_adapter_t. phandle is renamed to adap inside function bodies. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Define device name string pointers constantSylwester Nawrocki
Supresses following checkpatch warning: WARNING: static const char * array should probably be static const char * const Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Move variable declarations to the headerSylwester Nawrocki
Fixes following checkpatch.pl warning: WARNING: externs should be avoided in .c files Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Use linux/uaccess.h instead of asm/uaccess.hSylwester Nawrocki
Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Remove linkage specifiers for C++Sylwester Nawrocki
The as10x_cmd.h header is not public so there should be no need for an "extern "C"" in it. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Replace printk(KERN_<LEVEL> witk pr_<level>Sylwester Nawrocki
While at it also correct some spelling errors. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Whitespace and indentation cleanupSylwester Nawrocki
Remove some unnecessary braces. Replace spaces with tabs where expected. Replace gcc specific __FUNCTION__ with C99 __func__. No functional changes. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Fix the dvb device registration error pathSylwester Nawrocki
Release already acquired resources when error happens during devices registration steps. Use dev_err() where struct device is available, instead of driver specific err(). Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Replace pragma(pack) with attribute __packedSylwester Nawrocki
Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Piotr Chmura <chmooreck@poczta.onet.pl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Make the driver select CONFIG_FW_LOADERSylwester Nawrocki
It doesn't seem to be of much advantage to compile in FW_LOADER support conditionally, then make the driver always select FW_LOADER and remove #idefs from the code. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Remove leftovers of the SPI bus driverSylwester Nawrocki
SPI bus driver support is not included in this module, the SPI driver files are missing. But some bits are still present so clean up the unused code. The SPI driver support can be properly added later if needed. Then CONFIG_AS102_SPI and CONFIG_AS102_USB is now not needed and the pre-processor statements using these config options can now be removed from *.c files. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Remove unnecessary typedefsSylwester Nawrocki
According to the kernel coding rules typedefs should be avoided, so replace theit occurances with explicit enum/union types. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] staging: as102: Remove comment tags for editors configurationPiotr Chmura
Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Piotr Chmura <chmooreck@poczta.onet.pl> Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] it913x-fe ver 1.10 correct SNR reading from frontendMalcolm Priestley
Correction of reading from frontend and represents a SNR nonlinear scale of minimum signal to full signal. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] bt8xx: add support for PCI device ID 0x36cPeter De Schrijver
add support for conexant PCI device 0x36c. Seems to be fully compatible with the currently supported chips, yet the chip has different PCI ID. Signed-off-by: Peter De Schrijver <p2@psychaos.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] bt8xx: add support for Tongwei Video Technology TD-3116Peter De Schrijver
The following patch adds support for the Tongwei Video Technology TD-3116 board. This is a Bt878 based capture card with 16 inputs meant for surveilance applications. It also offers a way to check which inputs have a video signal while capturing another input. In addition there are a number of alarm inputs and outputs available and there is microcontroller which is presumably intended for use as a system watchdog. None of these extra capabilities are supported by the patch. Signed-off-by: Peter De Schrijver <p2@psychaos.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] it913x ver 1.09 support for USB 1 devices (IT9135)Malcolm Priestley
IT9135 devices do support USB 1. Support added with restricton on pid count to 5. IT9137 devices wil not connect in USB 1 mode. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] tvp5150: replace video standard "magic" numbersJavier Martinez Canillas
64933337e3cb61ca555969a35ab68b477db34ee2 [media] tvp5150: Add video format registers configuration values Added constants for each video standard supported by TVP5150, so this patch get rid of the magic numbers. Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] v4l: add G2D driver for s5p device familyKamil Debski
G2D is a 2D graphics accelerator engine present in the s5p family of Samsung SoCs. It is capable of bitblt and raster operations on images having dimensions of up to 8000x8000. Signed-off-by: Kamil Debski <k.debski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] tda18271: add tda18271_get_if_frequencyMichael Krufky
Reported-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] mxl5007t: add mxl5007t_get_if_frequencyMichael Krufky
Reported-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-08[media] mxl111sf: add mxl111sf_tuner_get_if_frequencyMichael Krufky
Reported-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-07[media] ttusb2: Don't use stack variables for DMAJosh Boyer
The ttusb2_msg function uses on-stack variables to submit commands to dvb_usb_generic. This eventually gets to the DMA api layer and will throw a traceback if the debugging options are set. This allocates the temporary buffer variables with kzalloc instead. Fixes https://bugzilla.redhat.com/show_bug.cgi?id=734506 Signed-off-by: Josh Boyer <jwboyer@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-07[media] it913x-fe ver 1.09 amend adc table entriestvboxspy
Amend adc table entries and size. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-07[media] it913x Support it9135 Verions 2 chipMalcolm Priestley
Support for version 2 type chips and other LNA versions of version 1 Scripts may be compressed slightly at a later stage. TODO Firmware loader However, things are a little confusing, it is not clear that dvb-usb-it9137-01.fw does not work with version 2 chips as in recent files both firmwares are the same. Should be applied to: 8133 Support for single ITE 9135 device. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-07[media] s5h1411: Calculate signal strength shown as percentage from SNR up ↵Michael Krufky
to 35dB As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB Even though the SNR can go higher than 35dB, there is some comfort factor in having a range of strong signals that can show at 100% Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-07[media] s5h1409: Calculate signal strength shown as percentage from SNR up ↵Michael Krufky
to 35dB As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB Even though the SNR can go higher than 35dB, there is some comfort factor in having a range of strong signals that can show at 100% Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-11-07[media] au8522: Calculate signal strength shown as percentage from SNR up to ↵Michael Krufky
35dB As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB Even though the SNR can go higher than 35dB, there is some comfort factor in having a range of strong signals that can show at 100% Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-20 11:24:29 +0000