| Age | Commit message (Collapse) | Author |
|---|
|
if filename is encrypted, filename could have no printable characters.
so remove it.
Signed-off-by: Hyunchul Lee <cheol.lee@lge.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
When fscrypt_setup_filename() fails we have to free dev.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
In commit 6afaf8a484cb ("UBI: flush wl before clearing update marker") I
managed to trigger and fix a similar bug. Now here is another version of
which I assumed it wouldn't matter back then but it turns out UBI has a
check for it and will error out like this:
|ubi0 warning: validate_vid_hdr: inconsistent used_ebs
|ubi0 error: validate_vid_hdr: inconsistent VID header at PEB 592
All you need to trigger this is? "ubiupdatevol /dev/ubi0_0 file" + a
powercut in the middle of the operation.
ubi_start_update() sets the update-marker and puts all EBs on the erase
list. After that userland can proceed to write new data while the old EB
aren't erased completely. A powercut at this point is usually not that
much of a tragedy. UBI won't give read access to the static volume
because it has the update marker. It will most likely set the corrupted
flag because it misses some EBs.
So we are all good. Unless the size of the image that has been written
differs from the old image in the magnitude of at least one EB. In that
case UBI will find two different values for `used_ebs' and refuse to
attach the image with the error message mentioned above.
So in order not to get in the situation, the patch will ensure that we
wait until everything is removed before it tries to write any data.
The alternative would be to detect such a case and remove all EBs at the
attached time after we processed the volume-table and see the
update-marker set. The patch looks bigger and I doubt it is worth it
since usually the write() will wait from time to time for a new EB since
usually there not that many spare EB that can be used.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- Fix a potential deadlock in cpu_cooling driver, which was introduced
in 4.11-rc1. (Matthew Wilcox)
- Fix the cpu_cooling and devfreq_cooling code to handle possible error
return value from OPP calls, together with three minor fixes in the
same patch series. (Viresh Kumar)
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: cpu_cooling: Check OPP for errors
thermal: cpu_cooling: Replace dev_warn with dev_err
thermal: devfreq: Check OPP for errors
thermal: devfreq_cooling: Replace dev_warn with dev_err
thermal: devfreq: Simplify expression
thermal: Fix potential deadlock in cpu_cooling
|
|
Pull block fixes from Jens Axboe:
"Five fixes for this series:
- a fix from me to ensure that blk-mq drivers that terminate IO in
their ->queue_rq() handler by returning QUEUE_ERROR don't stall
with a scheduler enabled.
- four nbd fixes from Josef and Ratna, fixing various problems that
are critical enough to go in for this cycle. They have been well
tested"
* 'for-linus' of git://git.kernel.dk/linux-block:
nbd: replace kill_bdev() with __invalidate_device()
nbd: set queue timeout properly
nbd: set rq->errors to actual error code
nbd: handle ERESTARTSYS properly
blk-mq: include errors in did_work calculation
|
|
Merge xfrm_user validation fixes from Andy Whitcroft:
"Two patches we are applying to Ubuntu for XFRM_MSG_NEWAE validation
issue reported by ZDI.
The first of these is the primary fix, and the second is for a more
theoretical issue that Kees pointed out when reviewing the first"
* emailed patches from Andy Whitcroft <apw@canonical.com>:
xfrm_user: validate XFRM_MSG_NEWAE incoming ESN size harder
xfrm_user: validate XFRM_MSG_NEWAE XFRMA_REPLAY_ESN_VAL replay_window
|
|
Merge PTRACE_SETREGSET leakage fixes from Dave Martin:
"This series is the collection of fixes I proposed on this topic, that
have not yet appeared upstream or in the stable branches,
The issue can leak kernel stack, but doesn't appear to allow userspace
to attack the kernel directly. The affected architectures are c6x,
h8300, metag, mips and sparc.
[ Mark Salter points out that c6x has no MMU or other mechanism to
prevent userspace access to kernel code or data on c6x, but it
doesn't hurt to clean that case up too. ]
The bugs arise from use of user_regset_copyin(). Users of
user_regset_copyin() can work in one of two ways:
1) Copy directly to thread_struct or equivalent. (This seems to be
the design assumption of the regset API, and is the most common
approach.)
2) Copy to a local variable and then transfer to thread_struct. (A
significant minority of cases.)
Buggy code typically involves approach 2"
* emailed patches from Dave Martin <Dave.Martin@arm.com>:
sparc/ptrace: Preserve previous registers for short regset write
mips/ptrace: Preserve previous registers for short regset write
metag/ptrace: Reject partial NT_METAG_RPIPE writes
metag/ptrace: Provide default TXSTATUS for short NT_PRSTATUS
metag/ptrace: Preserve previous registers for short regset write
h8300/ptrace: Fix incorrect register transfer count
c6x/ptrace: Remove useless PTRACE_SETREGSET implementation
|
|
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's not clear what behaviour is sensible when doing partial write of
NT_METAG_RPIPE, so just don't bother.
This patch assumes that userspace will never rely on a partial SETREGSET
in this case, since it's not clear what should happen anyway.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill TXSTATUS, a well-defined default value is used, based on the
task's current value.
Suggested-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
regs_set() and regs_get() are vulnerable to an off-by-1 buffer overrun
if CONFIG_CPU_H8S is set, since this adds an extra entry to
register_offset[] but not to user_regs_struct.
So, iterate over user_regs_struct based on its actual size, not based on
the length of register_offset[].
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gpr_set won't work correctly and can never have been tested, and the
correct behaviour is not clear due to the endianness-dependent task
layout.
So, just remove it. The core code will now return -EOPNOTSUPPORT when
trying to set NT_PRSTATUS on this architecture until/unless a correct
implementation is supplied.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Kees Cook has pointed out that xfrm_replay_state_esn_len() is subject to
wrapping issues. To ensure we are correctly ensuring that the two ESN
structures are the same size compare both the overall size as reported
by xfrm_replay_state_esn_len() and the internal length are the same.
CVE-2017-7184
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When a new xfrm state is created during an XFRM_MSG_NEWSA call we
validate the user supplied replay_esn to ensure that the size is valid
and to ensure that the replay_window size is within the allocated
buffer. However later it is possible to update this replay_esn via a
XFRM_MSG_NEWAE call. There we again validate the size of the supplied
buffer matches the existing state and if so inject the contents. We do
not at this point check that the replay_window is within the allocated
memory. This leads to out-of-bounds reads and writes triggered by
netlink packets. This leads to memory corruption and the potential for
priviledge escalation.
We already attempt to validate the incoming replay information in
xfrm_new_ae() via xfrm_replay_verify_len(). This confirms that the user
is not trying to change the size of the replay state buffer which
includes the replay_esn. It however does not check the replay_window
remains within that buffer. Add validation of the contained
replay_window.
CVE-2017-7184
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes to multiple issues in virtio.
Most notably a regression fix for crashes reported by Fedora users.
Hibernate is still reportedly broken, working on it"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: prevent uninitialized variable use
virtio-balloon: use actual number of stats for stats queue buffers
virtio_balloon: init 1st buffer in stats vq
virtio_pci: fix out of bound access for msix_names
|
|
Pull KVM fixes from Paolo Bonzini:
"All x86-specific, apart from some arch-independent syzkaller fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: cleanup the page tracking SRCU instance
KVM: nVMX: fix nested EPT detection
KVM: pci-assign: do not map smm memory slot pages in vt-d page tables
KVM: kvm_io_bus_unregister_dev() should never fail
KVM: VMX: Fix enable VPID conditions
KVM: nVMX: Fix nested VPID vmx exec control
KVM: x86: correct async page present tracepoint
kvm: vmx: Flush TLB when the APIC-access address changes
KVM: x86: use pic/ioapic destructor when destroy vm
KVM: x86: check existance before destroy
KVM: x86: clear bus pointer when destroyed
KVM: Documentation: document MCE ioctls
KVM: nVMX: don't reset kvm mmu twice
PTP: fix ptr_ret.cocci warnings
kvm: fix usage of uninit spinlock in avic_vm_destroy()
KVM: VMX: downgrade warning on unexpected exit code
|
|
The latest gcc-7.0.1 snapshot reports a new warning:
virtio/virtio_balloon.c: In function 'update_balloon_stats':
virtio/virtio_balloon.c:258:26: error: 'events[2]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:260:26: error: 'events[3]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:261:56: error: 'events[18]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:262:56: error: 'events[17]' is used uninitialized in this function [-Werror=uninitialized]
This seems absolutely right, so we should add an extra check to
prevent copying uninitialized stack data into the statistics.
>From all I can tell, this has been broken since the statistics code
was originally added in 2.6.34.
Fixes: 9564e138b1f6 ("virtio: Add memory statistics reporting to the balloon driver (V4)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The virtio balloon driver contained a not-so-obvious invariant that
update_balloon_stats has to update exactly VIRTIO_BALLOON_S_NR counters
in order to send valid stats to the host. This commit fixes it by having
update_balloon_stats return the actual number of counters, and its
callers use it when pushing buffers to the stats virtqueue.
Note that it is still out of spec to change the number of counters
at run-time. "Driver MUST supply the same subset of statistics in all
buffers submitted to the statsq."
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When init_vqs runs, virtio_balloon.stats is either uninitialized or
contains stale values. The host updates its state with garbage data
because it has no way of knowing that this is just a marker buffer
used for signaling.
This patch updates the stats before pushing the initial buffer.
Alternative fixes:
* Push an empty buffer in init_vqs. Not easily done with the current
virtio implementation and violates the spec "Driver MUST supply the
same subset of statistics in all buffers submitted to the statsq".
* Push a buffer with invalid tags in init_vqs. Violates the same
spec clause, plus "invalid tag" is not really defined.
Note: the spec says:
When using the legacy interface, the device SHOULD ignore all values in
the first buffer in the statsq supplied by the driver after device
initialization. Note: Historically, drivers supplied an uninitialized
buffer in the first buffer.
Unfortunately QEMU does not seem to implement the recommendation
even for the legacy interface.
Cc: stable@vger.kernel.org
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Fedora has received multiple reports of crashes when running
4.11 as a guest
https://bugzilla.redhat.com/show_bug.cgi?id=1430297
https://bugzilla.redhat.com/show_bug.cgi?id=1434462
https://bugzilla.kernel.org/show_bug.cgi?id=194911
https://bugzilla.redhat.com/show_bug.cgi?id=1433899
The crashes are not always consistent but they are generally
some flavor of oops or GPF in virtio related code. Multiple people
have done bisections (Thank you Thorsten Leemhuis and
Richard W.M. Jones) and found this commit to be at fault
07ec51480b5eb1233f8c1b0f5d7a7c8d1247c507 is the first bad commit
commit 07ec51480b5eb1233f8c1b0f5d7a7c8d1247c507
Author: Christoph Hellwig <hch@lst.de>
Date: Sun Feb 5 18:15:19 2017 +0100
virtio_pci: use shared interrupts for virtqueues
The issue seems to be an out of bounds access to the msix_names
array corrupting kernel memory.
Fixes: 07ec51480b5e ("virtio_pci: use shared interrupts for virtqueues")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
|
|
SRCU uses a delayed work item. Skip cleaning it up, and
the result is use-after-free in the work item callbacks.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Fixes: 0eb05bf290cfe8610d9680b49abef37febd1c38a
Reviewed-by: Xiao Guangrong <xiaoguangrong.eric@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The nested_ept_enabled flag introduced in commit 7ca29de2136 was not
computed correctly. We are interested only in L1's EPT state, not the
the combined L0+L1 value.
In particular, if L0 uses EPT but L1 does not, nested_ept_enabled must
be false to make sure that PDPSTRs are loaded based on CR3 as usual,
because the special case described in 26.3.2.4 Loading Page-Directory-
Pointer-Table Entries does not apply.
Fixes: 7ca29de21362 ("KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT")
Cc: qemu-stable@nongnu.org
Reported-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
or VM memory are not put thus leaked in kvm_iommu_unmap_memslots() when
destroy VM.
This is consistent with current vfio implementation.
Signed-off-by: herongguang <herongguang.he@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A new EDAC driver for the Pondicherry2 memory controller IP found in
the Intel Apollo Lake platform and the Denverton microserver.
Plus small fixlets.
Normally I had this queued for 4.12 but Tony requested for the
pnd2_edac driver to possibly land in 4.11 therefore I'm sending it to
you now.
It is a driver for new hardware which people don't have yet so it
shouldn't cause any regressions.
The couple of patches ontop of it show that Qiuxu actually did test it
on the hardware he has access to :)"
* tag 'edac_for_4.11_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, pnd2_edac: Fix reported DIMM number
EDAC, pnd2_edac: Fix !EDAC_DEBUG build
EDAC: Select DEBUG_FS
EDAC, pnd2_edac: Add new EDAC driver for Intel SoC platforms
EDAC, i5000, i5400: Fix use of MTR_DRAM_WIDTH macro
EDAC, xgene: Fix wrongly spelled "procesing"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull more pin control fixes from Linus Walleij:
"Here is a bunch of pin control fixes again
A bit more than I'd like for this subsystem at this point, but what
can I do. They are all driver fixes for hardware issues, as like "we
forgot", "we didn't think of the fact that this could happen", "oops
that one goes there" etc
- Kconfig fixup for the TI IOdelay pinctrl-single add-on
- fix up a typo in the meson i2c ao groups
- switch a remapping back to use devm_ioremap() as
devm_ioremap_resource() does not allow for sharing memory regions
- do not clear the Qualcomm irq status bit in irq_unmask(), as this
can lead to missing interrupts while the irq handler is executing
- add irq_request/release_resources() on the ST driver
- add a bunch of mysteriously missing pingroups for high numbered
pins in the Qualcomm ipq4019 driver"
* tag 'pinctrl-v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: ipq4019: add missing pingroups for pins > 70
pinctrl: st: add irq_request/release_resources callbacks
pinctrl: qcom: Don't clear status bit on irq_unmask
pinctrl: samsung: Fix memory mapping code
pinctrl: meson-gxbb: Fix typo in i2c ao groups
pinctrl: ti: The IODelay driver is a DRA7xxx feature so depend on that SoC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- build warning fix
- defconfig updates
- wire up new statx syscall
* tag 'm68k-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up statx
m68k/defconfig: Update defconfigs for v4.11-rc1
m68k/bitops: Correct signature of test_bit()
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"A smattering of different small fixes for some random driver
subsystems. Nothing all that major, just resolutions for reported
issues and bugs.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
extcon: int3496: Set the id pin to direction-input if necessary
extcon: int3496: Use gpiod_get instead of gpiod_get_index
extcon: int3496: Add dependency on X86 as it's Intel specific
extcon: int3496: Add GPIO ACPI mapping table
extcon: int3496: Rename GPIO pins in accordance with binding
vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
ppdev: fix registering same device name
parport: fix attempt to write duplicate procfiles
auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
Drivers: hv: vmbus: Don't leak channel ids
Drivers: hv: util: don't forget to init host_ts.lock
Drivers: hv: util: move waiting for release to hv_utils_transport itself
vmbus: remove hv_event_tasklet_disable/enable
vmbus: use rcu for per-cpu channel list
mei: don't wait for os version message reply
mei: fix deadlock on mei reset
intel_th: pci: Add Gemini Lake support
intel_th: pci: Add Denverton SOC support
intel_th: Don't leak module refcount on failure to activate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single kernfs fix for 4.11-rc4 that resolves a reported
issue.
It has been in linux-next with no reported issues"
* tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: Check KERNFS_HAS_RELEASE before calling kernfs_release_file()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.11-rc4.
One of these fix a long-standing issue in the ldisc code that was
found by Dmitry Vyukov with his great fuzzing work. The other fixes
resolve other reported issues, and there is one revert of a patch in
4.11-rc1 that wasn't correct.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix data race in tty_ldisc_ref_wait()
tty: don't panic on OOM in tty_set_ldisc()
Revert "tty: serial: pl011: add ttyAMA for matching pl011 console"
tty: acpi/spcr: QDF2400 E44 checks for wrong OEM revision
serial: 8250_dw: Fix breakage when HAVE_CLK=n
serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO driver fixes from Greg KH:
"Here are some small IIO driver fixes for 4.11-rc4 that resolve a
number of tiny reported issues. All of these have been in linux-next
for a while with no reported issues"
* tag 'staging-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: imu: st_lsm6dsx: fix FIFO_CTRL2 overwrite during watermark configuration
iio: adc: ti_am335x_adc: fix fifo overrun recovery
iio: sw-device: Fix config group initialization
iio: magnetometer: ak8974: remove incorrect __exit markups
iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.11-rc4.
Nothing major here, just an bunch of small fixes, and a handfull of
good fixes from Johan for devices with crazy descriptors. There are a
few new device ids in here as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: gadget: f_hid: fix: Don't access hidg->req without spinlock held
usb: gadget: udc: remove pointer dereference after free
usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeed
usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval
usb: gadget: acm: fix endianness in notifications
usb: dwc3: gadget: delay unmap of bounced requests
USB: serial: qcserial: add Dell DW5811e
usb: hub: Fix crash after failure to read BOS descriptor
ACM gadget: fix endianness in notifications
USB: usbtmc: fix probe error path
USB: usbtmc: add missing endpoint sanity check
USB: serial: option: add Quectel UC15, UC20, EC21, and EC25 modems
usb: musb: fix possible spinlock deadlock
usb: musb: dsps: fix iounmap in error and exit paths
usb: musb: cppi41: don't check early-TX-interrupt for Isoch transfer
usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk
uwb: i1480-dfu: fix NULL-deref at probe
uwb: hwa-rc: fix NULL-deref at probe
USB: wusbcore: fix NULL-deref at probe
USB: uss720: fix NULL-deref at probe
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"These are all pretty minor. The fix for idle wakeup would be a bad bug
but has not been observed in practice.
The update to the gcc-plugins docs was Cc'ed to Kees and Jon, Kees
OK'ed it going via powerpc and I didn't hear from Jon.
- cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
- powerpc/64s: Fix idle wakeup potential to clobber registers
- Revert "powerpc/64: Disable use of radix under a hypervisor"
- gcc-plugins: update architecture list in documentation
Thanks to: Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav
Jain"
* tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
gcc-plugins: update architecture list in documentation
Revert "powerpc/64: Disable use of radix under a hypervisor"
powerpc/64s: Fix idle wakeup potential to clobber registers
cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a memory leak on an error path, and two races when modifying
inodes relating to the inline_data and metadata checksum features"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix two spelling nits
ext4: lock the xattr block before checksuming it
jbd2: don't leak memory if setting up journal fails
ext4: mark inode dirty after converting inline directory
|
|
DIMM number passed to edac_mc_handle_error() was accidentally hardcoded
to zero. Pass in the correct daddr->dimm value.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt
Pull fscrypto fixes from Ted Ts'o:
"A code cleanup and bugfix for fs/crypto"
* tag 'fscrypt-for-linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: eliminate ->prepare_context() operation
fscrypt: remove broken support for detecting keyring key revocation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- bug fixes in asus_atk0110, it87 and max31790 drivers
- added missing API definition to hwmon core
* tag 'hwmon-for-linus-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (asus_atk0110) fix uninitialized data access
hwmon: Add missing HWMON_T_ALARM
hwmon: (it87) Avoid registering the same chip on both SIO addresses
hwmon: (max31790) Set correct PWM value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"This has been a slow -rc cycle for the RDMA subsystem. We really
haven't had a lot of rc fixes come in. This pull request is the first
of this entire rc cycle and it has all of the suitable fixes so far
and it's still only about 20 patches. The fix for the minor breakage
cause by the dma mapping patchset is in here, as well as a couple
other potential oops fixes, but the rest is more minor.
Summary:
- fix for dma_ops change in this kernel, resolving the s390, powerpc,
and IOMMU operation
- a few other oops fixes
- the rest are all minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/qib: fix false-postive maybe-uninitialized warning
RDMA/iser: Fix possible mr leak on device removal event
IB/device: Convert ib-comp-wq to be CPU-bound
IB/cq: Don't process more than the given budget
IB/rxe: increment msn only when completing a request
uapi: fix rdma/mlx5-abi.h userspace compilation errors
IB/core: Restore I/O MMU, s390 and powerpc support
IB/rxe: Update documentation link
RDMA/ocrdma: fix a type issue in ocrdma_put_pd_num()
IB/rxe: double free on error
RDMA/vmw_pvrdma: Activate device on ethernet link up
RDMA/vmw_pvrdma: Dont hardcode QP header page
RDMA/vmw_pvrdma: Cleanup unused variables
infiniband: Fix alignment of mmap cookies to support VIPT caching
IB/core: Protect against self-requeue of a cq work item
i40iw: Receive netdev events post INET_NOTIFIER state
|
|
Pull audit fix from Paul Moore:
"We've got an audit fix, and unfortunately it is big.
While I'm not excited that we need to be sending you something this
large during the -rcX phase, it does fix some very real, and very
tangled, problems relating to locking, backlog queues, and the audit
daemon connection.
This code has passed our testsuite without problem and it has held up
to my ad-hoc stress tests (arguably better than the existing code),
please consider pulling this as fix for the next v4.11-rcX tag"
* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
audit: fix auditd/kernel connection state tracking
|
|
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
We must lock the xattr block before calculating or verifying the
checksum in order to avoid spurious checksum failures.
https://bugzilla.kernel.org/show_bug.cgi?id=193661
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of Sunxi and Rockchip clk driver fixes and a core framework
one where we need to copy a string because we can't guarantee it isn't
freed sometime later"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
clk: sunxi-ng: Fix div/mult settings for osc12M on A64
clk: rockchip: Make uartpll a child of the gpll on rk3036
clk: rockchip: add "," to mux_pll_src_apll_dpll_gpll_usb480m_p on rk3036
clk: core: Copy connection id
dt-bindings: arm: update Armada CP110 system controller binding
clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
clk: sunxi: ccu-sun5i needs nkmp
clk: sunxi-ng: mp: Adjust parent rate for pre-dividers
|
|
aarch64-linux-gcc-7 complains about code it doesn't fully understand:
drivers/infiniband/hw/qib/qib_iba7322.c: In function 'qib_7322_txchk_change':
include/asm-generic/bitops/non-atomic.h:105:35: error: 'shadow' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is right, and despite trying hard, I could not come up with a version
that I liked better than just adding a fake initialization here to shut up the
warning.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When the rdma device is removed, we must cleanup all
the rdma resources within the DEVICE_REMOVAL event
handler to let the device teardown gracefully. When
this happens with live I/O, some memory regions are
occupied. Thus, track them too and dereg all the mr's.
We are safe with mr access by iscsi_iser_cleanup_task.
Reported-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This workqueue is used by our storage target mode ULPs
via the new CQ API. Recent observations when working
with very high-end flash storage devices reveal that
UNBOUND workqueue threads can migrate between cpu cores
and even numa nodes (although some numa locality is accounted
for).
While this attribute can be useful in some workloads,
it does not fit in very nicely with the normal
run-to-completion model we usually use in our target-mode
ULPs and the block-mq irq<->cpu affinity facilities.
The whole block-mq concept is that the completion will
land on the same cpu where the submission was performed.
The fact that our submitter thread is migrating cpus
can break this locality.
We assume that as a target mode ULP, we will serve multiple
initiators/clients and we can spread the load enough without
having to use unbound kworkers.
Also, while we're at it, expose this workqueue via sysfs which
is harmless and can be useful for debug.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The caller might not want this overhead.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
According to C9-147, MSN should only be incremented when the last packet of
a multi packet request has been received.
"Logically, the requester associates a sequential Send Sequence Number
(SSN) with each WQE posted to the send queue. The SSN bears a one-
to-one relationship to the MSN returned by the responder in each re-
sponse packet. Therefore, when the requester receives a response, it in-
terprets the MSN as representing the SSN of the most recent request
completed by the responder to determine which send WQE(s) can be
completed."
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Consistently use types from linux/types.h to fix the following
rdma/mlx5-abi.h userspace compilation errors:
/usr/include/rdma/mlx5-abi.h:69:25: error: 'u64' undeclared here (not in a function)
MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,
/usr/include/rdma/mlx5-abi.h:69:29: error: expected ',' or '}' before numeric constant
MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,
Include <linux/if_ether.h> to fix the following rdma/mlx5-abi.h
userspace compilation error:
/usr/include/rdma/mlx5-abi.h:286:12: error: 'ETH_ALEN' undeclared here (not in a function)
__u8 dmac[ETH_ALEN];
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
