summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-01-27e1000e: cleanup hw.hBruce Allan
Remove unnecessary #include, forward prototype of struct e1000_adapter and an empty comment; fix a comment which mentions "static data for the MAC" which is not applicable to the following struct; and cleanup some whitespace issues. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove unused #defineBruce Allan
All references to E1000_ERT_2048 have been removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: adjust PM QoS requestBruce Allan
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan) suffer from dropped transactions on platforms with deep C-states when jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based platforms which recently had early-receive de-featured (for stability reasons) suffer from this. To resolve this for all devices, when jumbo frames are enabled set the PM QoS DMA latency request based on the size of the receive packet buffer less one full frame. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: correct maximum frame size on 82579Bruce Allan
The largest jumbo frame supported by the 82579 hardware is 9018. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove e1000e_commit_phy()Bruce Allan
Remove the function e1000e_commit_phy() and replace the few calls to it with the same function pointer that it would call. The function pointer is almost always set for the devices that access these code paths so there is no risk of a NULL pointer dereference; for the few instances where the function pointer might not be set (i.e. can be called for the few devices which do not have this function pointer set), check for a valid function pointer. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove e1000_get_cable_length()Bruce Allan
Remove the function e1000_get_cable_length() and replace the two calls to it with the same function pointer that it would call. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove e1000_get_phy_cfg_done()Bruce Allan
Remove the function e1000_get_phy_cfg_done() and replace the single call to it with the same function pointer that it would call. The function pointer is always set so there is no risk of a NULL pointer dereference. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: rename e1000_get_cfg_done()Bruce Allan
In keeping with the e1000e driver function naming convention, the subject function is renamed to indicate it is generic, i.e. it is applicable to more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove e1000_force_speed_duplex()Bruce Allan
Remove the function e1000_force_speed_duplex() and replace the single call to it with the same function pointer that it would call. The function pointer is always set so there is no risk of a NULL pointer dereference. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove e1000_set_d0_lplu_state()Bruce Allan
Replace the function e1000_set_d0_lplu_state() with the contents of it coded in place of the single call to the function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27gro: Fix kcalloc argument orderJoe Perches
First number, then size. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27irda: buffer overflow in irnet_ctrl_read()Dan Carpenter
The comments here say that the /* Max event is 61 char */ but in 2003 we changed the event format and now the max event size is 75. The longest event is: "Discovered %08x (%s) behind %08x {hints %02X-%02X}\n", 12345678901 23 456789012 34567890 1 2 3 +8 +21 +8 +2 +2 +1 = 75 characters. There was a check to return -EOVERFLOW if the user gave us a "count" value that was less than 64. Raising it to 75 might break backwards compatability. Instead I removed the check and now it returns a truncated string if "count" is too low. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27Merge branch 'intel'David S. Miller
Jeff Kirsher says: ==================== This series contains updates to e1000e only. All the updates come from Bruce Allan and most of the patch fix or enable features on i217/i218. Most notably is patch 03 "e1000e: add support for IEEE-1588 PTP", which is v2 of the patch based on feedback from Stephen Hemminger. Also patch 04 "e1000e: enable ECC on I217/I218 to catch packet buffer memory errors" should be queued up for stable (as well as net) trees, but the patch does not apply cleanly to either of those trees currently. So I will work with Bruce to provide a version of the patch which will apply cleanly to net (and stable) and we can queue it up at that point for stable 3.5 tree. The remaining patches are general cleanups of the code. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27e1000e: cleanup: do not assign a variable a value when not necessaryBruce Allan
Static analysis with cppcheck has shown a few instances of a variable being reassigned a value before the old one has been used. None of these ever require the old value to be used so remove the old values. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: do not ignore variables which get set a valueBruce Allan
Static analysis with cppcheck has shown a few instances of a variable which is assigned a value that is never used. A number of these are the return status of various driver function calls which should be passed back to the caller of the current function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove unnecessary function prototypesBruce Allan
...and cleanup some whitespace in other prototypes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: add comment to spinlock_t definitionBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: remove definition of struct which is no longer usedBruce Allan
The e1000e driver has been converted to use extended descriptors instead of the older legacy descriptor type. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: fix PHY init workarounds for i217/i218Bruce Allan
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it back to power-on defaults. This includes setting it's MAC-PHY messaging mode to use the PCIe-like interconnect, so the MAC must also be set back from SMBus mode to PCIe mode otherwise the PHY can be inaccessible. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: correct maximum frame size on i217/i218Bruce Allan
The largest jumbo frame supported by the i217 and i218 hardware is 9018. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: update copyright dateBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: remove prototype of non-existent functionBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: prevent hardware from automatically configuring PHY on I217/I218Bruce Allan
As done with the previous generation managed 82579, prevent the PHY from being put into an unknown state by blocking the hardware from automatically configuring the PHY as done with the previous generation managed 82579. Instead, the driver should configure the PHY with contents of the EEPROM image. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: enable ECC on I217/I218 to catch packet buffer memory errorsBruce Allan
In rare instances, memory errors have been detected in the internal packet buffer memory on I217/I218 when stressed under certain environmental conditions. Enable Error Correcting Code (ECC) in hardware to catch both correctable and uncorrectable errors. Correctable errors will be handled by the hardware. Uncorrectable errors in the packet buffer will cause the packet to be received with an error indication in the buffer descriptor causing the packet to be discarded. If the uncorrectable error is in the descriptor itself, the hardware will stop and interrupt the driver indicating the error. The driver will then reset the hardware in order to clear the error and restart. Both types of errors will be accounted for in statistics counters. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: add support for IEEE-1588 PTPBruce Allan
Add PTP IEEE-1588 support and make accesible via the PHC subsystem. v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: fix flow-control thresholds for jumbo frames on 82579/I217/I218Bruce Allan
The previous static flow-control thresholds were causing unnecessary pause packets to be transmitted when jumbo frames are configured reducing the throughput. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: fix ethtool offline register test for I217Bruce Allan
The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and SHRAL/H registers. Set R/W bit-mask appropriately for SHRAH[9] when testing the R/W ability of the register. Also, fix the error message log format so that it does not provide misleading information (i.e. the logged register address could be incorrect). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27soreuseport: fix use of uid in tb->fastuidTom Herbert
Fix a reported compilation error where ia variable of type kuid_t was being set to zero. Eliminate two instances of setting tb->fastuid to zero. tb->fastuid is only used if tb->fastreuseport is set, so there should be no problem if tb->fastuid is not initialized (when tb->fastreuesport is zero). Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27Remove leftover #endif after introducing SO_REUSEPORTThomas Graf
Commit 055dc21a1d (soreuseport: infrastructure) removed the #if 0 around SO_REUSEPORT without removing the corresponding #endif thus causing the header guard to close early. Cc: Tom Herbert <therbert@google.com> Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: Bump up the version to 5.1.32Jitendra Kalsaria
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: add support for FDB netdevice ops.Jitendra Kalsaria
Providing communication channel between KVM and e-Switch so that it can be informed when hypervisor configures a MAC address and VLAN. qlcnic_mac_learn module param usage will be changed to: 0 = MAC learning is disable 1 = Driver learning is enable 2 = FDB learning is enable Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: sleeping function called from invalid contextJitendra Kalsaria
device eth0 entered promiscuous mode BUG: sleeping function called from invalid context at mm/slub.c:930 in_atomic(): 1, irqs_disabled(): 0, pid: 5911, name: brctl INFO: lockdep is turned off. Pid: 5911, comm: brctl Tainted: GF W O 3.6.0-0.rc7.git1.4.fc18.x86_64 #1 Call Trace: [<ffffffff810a29ca>] __might_sleep+0x18a/0x240 [<ffffffff811b5d77>] __kmalloc+0x67/0x2d0 [<ffffffffa00a61a9>] ? qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic] [<ffffffffa00a61a9>] qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic] [<ffffffffa009e1c1>] qlcnic_set_multi+0x81/0x100 [qlcnic] [<ffffffff8159cccf>] __dev_set_rx_mode+0x5f/0xb0 [<ffffffff8159cd4f>] dev_set_rx_mode+0x2f/0x50 [<ffffffff8159d00c>] dev_set_promiscuity+0x3c/0x50 [<ffffffffa05ed728>] br_add_if+0x1e8/0x400 [bridge] [<ffffffffa05ee2df>] add_del_if+0x5f/0x90 [bridge] [<ffffffffa05eee0b>] br_dev_ioctl+0x4b/0x90 [bridge] [<ffffffff8159d613>] dev_ifsioc+0x373/0x3b0 [<ffffffff8159d78f>] dev_ioctl+0x13f/0x860 [<ffffffff812dd6e1>] ? avc_has_perm_flags+0x31/0x2c0 [<ffffffff8157c18d>] sock_do_ioctl+0x5d/0x70 [<ffffffff8157c21d>] sock_ioctl+0x7d/0x2c0 [<ffffffff812df922>] ? inode_has_perm.isra.48.constprop.61+0x62/0xa0 [<ffffffff811e4979>] do_vfs_ioctl+0x99/0x5a0 [<ffffffff812df9f7>] ? file_has_perm+0x97/0xb0 [<ffffffff810d716d>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff811e4f19>] sys_ioctl+0x99/0xa0 [<ffffffff816e7369>] system_call_fastpath+0x16/0x1b br0: port 1(eth0) entered forwarding state br0: port 1(eth0) entered forwarding state Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: Fix LED/Beaconing tests to work on all ports of an adapter.Himanshu Madhani
Provide port number in command payload for LED/Beaconing tests. Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: avoid mixed mode interrupts for some adapter typesManish chopra
o Some adapter types do not support co-existence of Legacy Interrupt with MSI-x or MSI among multiple functions. For those adapters, prevent attaching to a function during normal load, if MSI-x or MSI vectors are not available. o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in legacy mode for all functions in the adapter. Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: enable RSS for TCP over IPv6Shahed Shaikh
o This patch enables RSS for TYPE-C packets to enable RSS for TCP over IPv6 Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: enable LRO on IPv6 without dest ip checkShahed Shaikh
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27qlcnic: set driver version in firmwareSritej Velaga
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-27Merge branch 'master' of git://1984.lsi.us.es/nf-nextDavid S. Miller
Pablo Neira Ayuso says: ==================== This batch contains netfilter updates for you net-next tree, they are: * The new connlabel extension for x_tables, that allows us to attach labels to each conntrack flow. The kernel implementation uses a bitmask and there's a file in user-space that maps the bits with the corresponding string for each existing label. By now, you can attach up to 128 overlapping labels. From Florian Westphal. * A new round of improvements for the netns support for conntrack. Gao feng has moved many of the initialization code of each module of the netns init path. He also made several code refactoring, that code looks cleaner to me now. * Added documentation for all possible tweaks for nf_conntrack via sysctl, from Jiri Pirko. * Cisco 7941/7945 IP phone support for our SIP conntrack helper, from Kevin Cernekee. * Missing header file in the snmp helper, from Stephen Hemminger. * Finally, a couple of fixes to resolve minor issues with these changes, from myself. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-23ixgbevf: Fix link speed message to support 100MbpsGreg Rose
The X540 can link at 100Mbps - fix the link speed indicator message to show that value. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Limit number of reported VFs to device specific valueDonald Dutile
ixgbe claims it supports 64 VFs in its SRIOV capability structure, but the driver only supports 63. Adjust it so sysfs sriov configuration checking will check with the proper totalvf value. Signed-off-by: Donald Dutile <ddutile@redhat.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Implement PCI SR-IOV sysfs callback operationGreg Rose
Implement callbacks in the driver for the new PCI bus driver interface that allows the user to enable/disable SR-IOV VFs in a device via the sysfs interface. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> CC: Don Dutile <ddutile@redhat.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Modularize SR-IOV enablement codeGreg Rose
In preparation for enable/disable of SR-IOV via the PCI sysfs interface move some core SR-IOV enablement code that would be common to module parameter usage or callback from the PCI bus driver to a separate function so that it can be used by either method. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> CC: Don Dutile <ddutile@redhat.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <Sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Make mailbox ops initialization unconditionalGreg Rose
There is no actual dependency on initialization of the mailbox ops on whether SR-IOV is enabled or not and it doesn't hurt to go ahead and initialize ops unconditionally. Move the initialization into the device probe so that the mailbox ops are initialized at the time we have the board info necessary to do it. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> CC: Don Dutile <ddutile@redhat.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <Sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: only compile ixgbe_debugfs.o when enabledJacob Keller
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe driver to only compile the file when the config is enabled. This means we can remove the #ifdef inside the ixgbe_debugfs.c file. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Inline Rx PTP descriptor handlingAlexander Duyck
This change is meant to inline the Rx PTP descriptor handling. The main motivation is to avoid unnecessary jumps into function calls that we then immediately exit because we are not performing timestamps. The net result of this change is that ixgbe_ptp_rx_tstamp drops from .5% CPU utilization in my performance runs to 0%, and the only value tested is the Rx descriptor which should already be warm in the cache if not stored in a register. Cc: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jacob Keller <Jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Fix overwriting of rx_mtrl in ixgbe_ptp_hwtstamp_ioctlJacob Keller
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for the UDP port to timestamp on was moved above the switch statement, but was overwritten to 0 if the ioctl selected one of the V1 filters. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: add warning when scheduling resetJacob Keller
This patch adds warnings when a reset of the adapter is scheduled so that the user can see log of why the reset occurred. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Add ptp work item to poll for the Tx timestampJacob Keller
This patch copies the igb implementation of Tx timestamps, which uses a work item to poll for the Tx timestamp. In addition it adds a timeout value of 15 seconds, after which it will stop polling. This is necessary due to an issue with the descriptor being marked done before the Tx timestamp event has occurred. These two events don't correlate, so using the done bit on the descriptor as indication that the timestamp must already have been taken leads to potentially dropped Tx timestamps (especially under heavy packet load) Reported-by: Matthew Vick <matthew.vick@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-23ixgbe: Use watchdog check in favor of BPF for detecting latched timestampJacob Keller
This patch removes ixgbe_ptp_match, and the corresponding packet filtering from ixgbe driver. This code was previously causing some issues within the hotpath of the driver. However the code also provided a check against possible frozen Rx timestamp due to dropped packets when the Rx ring is full. This patch provides a replacement solution based on the watchdog. To this end, whenever a packet consumes the Rx timestamp it stores the jiffy value in the rx_ring structure. Watchdog updates its own jiffy timer whenever there is no valid timestamp in the registers. If watchdog detects a valid timestamp in the registers, (meaning that no Rx packet has consumed it yet) it will check which time is most recent, the last time in the watchdog, or any time in the rx_rings. If the most recent "event" was more than 5seconds ago, it will flush the Rx timestamp and print a warning message to the syslog. Reported-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-12 05:08:11 +0000