| Age | Commit message (Collapse) | Author |
|---|
|
This camera has a sensor type we did not support sofar, this patch adds
support for the new sensor type found in the Sakar 1638x CyberPix.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In 640x480, if the reg11 has less than 4, the image is
unstable (the bridge goes into a higher compression mode
which we have not reverse engineered yet).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
exposure ctrls
Fixup brightness ctrl and add gain and exposure ctrls for PAS202BCB sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
expo ctrl
Some sensors only allow controlling the exposure by changing the clockdiv,
which means that exposure takes pretty large jumps (for example when going
from a div of 1 to 2, the exposure doubles). Use 2 different entries in
the controls array for these 2 different types of exposure (always
disabling one), and;
Add a new autogain algorithm for the coarse exposure case, which normally
changes the gain setting, only touching the exposure setting if the desired
luminance cannot be reached with gain, and after an exposure change once more
first tries gain, etc. Thus avoiding exposure changes, and the resulting
oscilation because of the huge steps these exposure controls take.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Leave bridge gain at 1.0 when we have a sensor gain, while at it also
change the bridge gain setting code to write both registers in one go
saving us a usb transaction.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gspca_sonixj: Add camera button support
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gspca_sonixb: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gscpa_zc3xx: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gscpa_pac7311: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gscpa_pac207: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gscpa Documentation: add cpia1 cameras
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gspca_sq905c: Add an additional USB-ID
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Simplify sensor detection a bit (share more of the code between cif and vga
cameras). Also remove an unnecessary write from zero_the_pointer().
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Based on experiments by Eric Wescott, edit the Sony GigaPocket (Kikyou)
card entry video and audio mux settings.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is a slightly modified version of Eric Anderson's original patch
for the Sony Giga Pocket board. It has been updated to apply to the
latest ivtv driver version by Hans Verkuil <hverkuil@xs4all.nl> and
Andy Walls <awalls@radix.net>. Also Andy Walls modified the patch to
use a new Sony BTF-Pnx01Z tuner entry based on Eric Anderson's experimental
findings for the bandswitch.
>From Eric Anderson's original email:
1. The tuner on the card doesn't seem to match any standard
ones. I modified an existing tuner entry. Ideally a new tuner
entry should be created. (The only difference from the one I
modified is that the low-to-mid range frequency cut-off is
slightly different, as are the bit config settings.)
2. It wasn't obvious how to choose a second audio input other
than using "radio" as an option. Basically there's two GPIO
audio inputs. Using radio allowed me to avoid major restructuring
to the code. (perhaps other cards don't have this often...)
3. It's not clear that there's a mute setting that works. Not
sure why.
4. I haven't had a chance to test the two Svideo inputs. I set
them to COMPOSITE1 and SVIDEO2, but I'm not sure those are the
correct settings. The standard composite video inputs seem to work.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Sony makes custome tuners for its GigaPocket line of ivtv based capture
cards. This adds an entry to the tuner-types list for such tuners.
Parameters are based on experiments by Eric Anderson <rico99@sbcglobal.net>.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
ivtv_api_get_data() was performing more PCI MMIO than needed, resulting
often in it accounting for more than half the total time spent in
ivtv_irq_handler(). Now it only reads at most 7 of the 16 mailbox data words
over the PCI bus, and in some instances only 2 or 3 data words as needed.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Adding Makefile and Kconfig for ISIF driver
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Enhancements to support DM365 ISP5 and VPSS module configuration.
Also cleaned up the driver by removing redundant variables.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is the source file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for YUV capture from
TVP514x driver. This patch contains the header files required for this driver.
Reviewed-by: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is the header file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for
YUV capture from TVP514x driver. This patch contains the header files required
for this driver.
Reviewed-by: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We know that the 300msec settling time after starting the digitizer is
only really needed when the digitizer is a SAA7115. So if we're not
using a SAA7115, skip the delay.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
After implementing a 300msec wait between digitizer start and encoder
start, it has been determined that we don't need to wait quite as long
before configuring the encoder. This reduces the wait period from
100msec back to 50msec.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Martin Dauskardt <martin.dauskardt@gmx.de> has determined that the
encoder has a much better chance of starting cleanly if we
deliberately hold off starting it util the video digitizer has had a
chance to run for at least 300msec first. These changes implement an
enforced 300msec wait in the state machine that orchestrates streaming
start / stop.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
CC: Jonathan Corbet <corbet@lwn.net>
CC: Reviewed-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Videobuf is a moderately complex API which most V4L2 drivers should use,
but its documentation is...sparse. This document attempts to improve the
situation.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The media spec contains several errors in the description of the
I/O streaming ioctls, in particular with respect to the userptr
I/O method.
The most important change is that you really need to set count
and index in v4l2_requestbuffer and v4l2_buffer when dealing with
user pointer streaming.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When the saa7111 driver was merged into saa7115 several bugs were introduced,
in particular with the saa7111a support as is used in the mxb.c driver.
This patch fixes the saa7111a support. This was tested with the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
v4l2_device_register needs to be called before the i2c subdevs are loaded.
However, it was called afterwards in the saa7146 driver. This caused an oops
when loading the mxb and hexium drivers. The vv_init function is now split
into two: one registers the v4l2_device, the other does the rest of the
initialization. The three drivers that depend on this have been updated to
call the new vv_devinit function.
Thanks to Michael Hunold for reporting this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The function return value wasn't checked due to a missing variable
assignment.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The Asus EeePC T91 integrated webcam exposes a gain control in the
processing unit but stalls when the control is queried. Blacklist the
gain control for that camera.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When setting a control, the V4L2 specification requires drivers to
either clamp the control value to the [minimum, maximum] range or return
the -ERANGE error.
Fix the driver to clamp control values to the valid range in
uvc_ctrl_set() and make sure the value differs from the minimum by an
integer multiple of step.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
menu index
The V4L2 specification states that out of bounds control values must
either be clamped to the valid range or result in a -ERANGE error code.
Fix the driver to return -ERANGE instead of -EINVAL when setting a menu
control to an invalid value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace the UVC_GUID_FORMAT and UVC_GUID_ARGS macros with the new %pUl
printk format specifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This fixes timeout issues with some Logitech webcams. The timeout value
seems to match the one used in the Logitech Windows driver, so no
further increase should be necessary.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Ensure that volume values are always in the allowed range. Otherwise,
it would be possible to set other bits in the AUD_VOL_CTL register or to
get a wrong sign in the AUD_BAL_CTL register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch addes timb-radio to all configurations of the timberdale MFD.
Connected to the FPGA is a TEF6862 tuner and a SAA7706H DSP, the I2C
board info of these devices is passed via the timb-radio platform data.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: sameo@linux.intel.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The parenthesis was misplaced, tmp is set to 0 or break occurs,
while debugging opera1_usb_i2c_msgxfer() retval was not shown.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
CC: Marco Gittler <g.marco@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A small mistake on the last patch broke demod s-code setup for
XC3028L (firmware 3.2 and upper). Fix it.
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
There's one reported regression in Australia (DTV7) and some
reported troubles with newer firmwares found on xc3028l chips.
Rework the logic to improve tuner on those cases.
Thanks-to: Robert Lowery <rglowery@exemail.com.au>
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Tested-by: Robert Lowery <rglowery@exemail.com.au>
CC: stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add a new module parameter "disable_ir" to disable IR support. Several
other drivers do that already, and this can be very handy for
debugging purposes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
I succeeded in running Cinergy Hybrid T USB XS FR in both modes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix sparse warnings in media/dvb/frontends:
drivers/media/dvb/frontends/dibx000_common.c:177:13: warning: non-ANSI function declaration of function 'systime'
drivers/media/dvb/frontends/tda665x.c:136:55: warning: right shift by bigger than source value
[mchehab@redhat.com: removed the change at dib0090 since it got fixed by a previous patch]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Userspace is allowed to coalesce events between SYNCs. And since the code
emits UP right after DOWN for the same key, it may be missed
(up+down=nothing). Add an extra sync in between UP and DOWN events to disable
the coalesce.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
