| Age | Commit message (Collapse) | Author |
|---|
|
During an audio playback session it is observed that, audio goes off after
few seconds of continuous pause and play. No audio is heard even when the
playback is resumed.
The reason for above is, currently ADMA driver does not handle DMA_PAUSE/
DMA_RESUME and relevant callbacks for dma_device are not implemented. This
patch implements device_pause and device_resume callbacks for the device.
During pause TRANSFER_PAUSE bit of dma channel control register is set and
the same is cleared during resume.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add Tegra186 specific macro defines and chip_data structure for chip
specific information. New compatibility is added to select relevant
chip details. There is no major change for Tegra194 and hence it can
use the same chip data.
The bits in the BURST_SIZE field of the ADMA CH_CONFIG register are
encoded differently on Tegra186 and Tegra194 compared with Tegra210.
On Tegra210 the bits are encoded as follows ...
1 = WORD_1
2 = WORDS_2
3 = WORDS_4
4 = WORDS_8
5 = WORDS_16
Where as on Tegra186 and Tegra194 the bits are encoded as ...
0 = WORD_1
1 = WORDS_2
2 = WORDS_3
3 = WORDS_4
4 = WORDS_5
...
15 = WORDS_16
Add helper functions for generating the correct burst size.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Tegra186 Audio DMA controller has new updates from Tegra210 version.
Thus add new compatibility binding string and the same can be used
by Tegra194 as well.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This is a preparatory patch to add support for Tegra186 and Tegra194 chips.
Following changes are necessary to make driver code generic.
* chip_data structure is enhanced to have chip specific details and
following are the additions to the structure
* Offset addresses for ADMA global and channel registers
* Offset values for Tx and Rx channel selection
* Maximum supported Tx and Rx channels
* Tx and Rx channel request mask
* ADMA channel register space size
* Make use of above chip_data to generalise the driver code
Support for Tegra186 and Tegra194 will be added in subsequent patches of
the series.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We switched this code from spin_lock_bh() to vanilla spin_lock() but
there was one stray spin_unlock_bh() that was overlooked. This
patch converts it to spin_unlock() as well.
Fixes: d8570d018f69 ("dmaengine: at_xdmac: move spin_lock_bh to spin_lock in tasklet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix indentation and remove unneeded space after 'return' keyword. This
fixes checkpatch warning:
WARNING: Statements should start on a tabstop
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix typo in comment for Vybrid SoC family.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In double buffer mode, during residue calculation, the DMA can
automatically switch to the next transfer. Indeed the CT bit that
gives position in the double buffer can has been updated by the
hardware, during calculation.
In this case the SxNDTR register value can not be trusted.
If a transition is detected we consider that the DMA has switched to
the beginning of next sg.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Using dev_get_drvdata directly.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Using dev_get_drvdata directly.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit f4fd2ec08f17: ("dmaengine: stm32-dma: use platform_get_irq()") used
unsigned variable irq to store the results and check later for negative
errors, so update the code to use signed variable for this
Fixes: f4fd2ec08f17 ("dmaengine: stm32-dma: use platform_get_irq()")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ) is not recommended for
requesting IRQ's resources, as they can be not ready yet. Using
platform_get_irq() instead is preferred for getting IRQ even if it was
not retrieved earlier.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Update copyright and string for Gen3.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
On imx8mq B0 chip, AHB/SDMA clock ratio 2:1 can't be supported,
since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach
to 500Mhz, so use 1:1 instead.
To limit this change to the imx8mq for now this patch also adds an
im8mq-sdma compatible string.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Acked-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There is a spelling mistake in a chan_dbg message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There are two drivers that are relying on the iDMA 64-bit driver name
to match. Instead of duplicating string in both of them, dedicate
a header file and share it between users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This patch kill instructs the DMAC to immediately terminate
execution of a thread. and then clear the interrupt status,
at last, stop generating interrupts for DMA_SEV. to guarantee
the next dma start is clean. otherwise, one interrupt maybe leave
to next start and make some mistake.
we can reporduce the problem as follows:
DMASEV: modify the event-interrupt resource, and if the INTEN sets
function as interrupt, the DMAC will set irq<event_num> HIGH to
generate interrupt. write INTCLR to clear interrupt.
DMA EXECUTING INSTRUCTS DMA TERMINATE
| |
| |
... _stop
| |
| spin_lock_irqsave
DMASEV |
| |
| mask INTEN
| |
| DMAKILL
| |
| spin_unlock_irqrestore
in above case, a interrupt was left, and if we unmask INTEN, the DMAC
will set irq<event_num> HIGH to generate interrupt.
to fix this, do as follows:
DMA EXECUTING INSTRUCTS DMA TERMINATE
| |
| |
... _stop
| |
| spin_lock_irqsave
DMASEV |
| |
| DMAKILL
| |
| clear INTCLR
| mask INTEN
| |
| spin_unlock_irqrestore
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Since device_prep_interleaved_dma() is already implemented, the
DMA_INTERLEAVE capability should be set.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In 2D transfers (for the AXI DMAC), the number of frames (numf) represents
Y_LENGTH, and the length of a frame is X_LENGTH. 2D transfers are useful
for video transfers where screen resolutions ( X * Y ) are typically
aligned for X, but not for Y.
There is no requirement for Y_LENGTH to be aligned to the bus-width (or
anything), and this is also true for AXI DMAC.
Checking the Y_LENGTH for alignment causes false errors when initiating DMA
transfers. This change fixes this by checking only that the Y_LENGTH is
non-zero.
Fixes: 0e3b67b348b8 ("dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some synthesis time configuration parameters of the DMA controller can be
inferred from the hardware itself.
Use this information as it is more reliably than the information specified
in the devicetree which might be outdated if the HDL project got changed.
Deprecate the devicetree properties that can be inferred from the hardware
itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The overflow error flag (ROI: Request Overflow Error) is only relevant
for the case when the channel handles a peripheral synchronized transfer.
Not in the case of memory to memory transfer where there is no hardware
request signal.
Remove the use of this interrupt source in such a case. It's based on
the first descriptor which holds the configuration for the whole
linked list transfer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Complement the identification of errors with stopping the channel and
dumping the descriptor that led to the error case.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Even if this case shouldn't happen when controller is properly programmed,
it's still better to avoid dumping a kernel Oops for this.
As the sequence may happen only for debugging purposes, log the error and
just finish the tasklet call.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The AXI DMAC driver is currently supported also on the Xilinx ZynqMP
architecture. This change allows this driver to be enabled & used on it as
well.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It is unnecessary to call spin_lock_bh in a tasklet.
Signed-off-by: Jeff Xie <chongguiguzi@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Current way we find a waiting virtual channel for the next transfer
at the time one physical channel becomes free is not really fair.
More in details, in case there is more than one channel waiting at a time,
by just going through the arrays of memcpy and slave channels and stopping
as soon as state match waiting state, channels with high indexes can be
penalized.
Whenever dma engine is substantially overloaded so that we constantly
get several channels waiting, channels with highest indexes might not
be served for a substantial time which in the worse case, might hang
task that wait for dma transfer to complete.
This patch makes physical channel re-assignment more fair by storing
time in jiffies when a channel is put in waiting state. Whenever a
physical channel has to be re-assigned, this time is used to select
channel that is waiting for the longest time.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nicolas Guion <nicolas.guion@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The axi-dmac driver currently rejects transfers with segments that are
larger than what the hardware can handle.
Re-work the driver so that these large segments are split into multiple
segments instead where each segment is smaller or equal to the maximum
segment size.
This allows the driver to handle transfers with segments of arbitrary size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Signed-off-by: Alexandru Ardelean <alex.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This patch adds debugfs interface to show the relationship between
DMA threads (hardware resource for transferring data) and DMA
channel ID of DMA slave.
Typically, PL330 has many slaves than number of DMA threads.
So sometimes PL330 cannot allocate DMA threads for all slaves even
if a user specify DMA channel ID in devicetree. This interface will
be useful for checking that DMA threads are allocated or not.
Below is an output sample:
$ sudo cat /sys/kernel/debug/ff1f0000.dmac
PL330 physical channels:
THREAD: CHANNEL:
-------- -----
0 8
1 9
2 11
3 12
4 14
5 15
6 10
7 --
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If the driver is active till late suspend, where runtime PM cannot run,
force suspend is essential in such case to put the device in low power
state. Thus pm_runtime_force_suspend and pm_runtime_force_resume are
used as system sleep callbacks during system wide PM transitions.
Late system sleep callbacks are used to ensure, for instance, that the
sound core has suspended any on-going activity, including stopping the
ADMA if active, before we attempt to suspend the ADMA.
Suggested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
adma driver is using pm_clk_*() interface for managing clock resources.
With this it is observed that clocks remain ON always. This happens on
Tegra devices which use BPMP co-processor to manage clock resources,
where clocks are enabled during prepare phase. This is necessary because
clocks to BPMP are always blocking. When pm_clk_*() interface is used on
such Tegra devices, clock prepare count is not balanced till remove call
happens for the driver and hence clocks are seen ON always. Thus this
patch replaces pm_clk_*() with devm_clk_*() framework.
Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- add more Build-Depends to Debian source package
- prefix header search paths with $(srctree)/
- make modpost show verbose section mismatch warnings
- avoid hard-coded CROSS_COMPILE for h8300
- fix regression for Debian make-kpkg command
- add semantic patch to detect missing put_device()
- fix some warnings of 'make deb-pkg'
- optimize NOSTDINC_FLAGS evaluation
- add warnings about redundant generic-y
- clean up Makefiles and scripts
* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: remove stale lxdialog/.gitignore
kbuild: force all architectures except um to include mandatory-y
kbuild: warn redundant generic-y
Revert "modsign: Abort modules_install when signing fails"
kbuild: Make NOSTDINC_FLAGS a simply expanded variable
kbuild: deb-pkg: avoid implicit effects
coccinelle: semantic code search for missing put_device()
kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
kbuild: add workaround for Debian make-kpkg
kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
unicore32: simplify linker script generation for decompressor
h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
kbuild: move archive command to scripts/Makefile.lib
modpost: always show verbose warning for section mismatch
ia64: prefix header search path with $(srctree)/
libfdt: prefix header search paths with $(srctree)/
deb-pkg: generate correct build dependencies
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm updates from Thomas Gleixner:
"Two cleanup patches removing dead conditionals and unused code"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Remove unused __constant_c_x_memset() macro and inlines
x86/asm: Remove dead __GNUC__ conditionals
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Three fixes for the fallout from the TSX errata workaround:
- Prevent memory corruption caused by a unchecked out of bound array
index.
- Two trivial fixes to address compiler warnings"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
perf/x86: Fixup typo in stub functions
perf/x86/intel: Fix memory corruption
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A fix for a Xen bug introduced by David's series for excluding
ballooned pages in vmcores"
* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Fix mapping PG_offline pages to user space
|
|
Pull 9p updates from Dominique Martinet:
"Here is a 9p update for 5.1; there honestly hasn't been much.
Two fixes (leak on invalid mount argument and possible deadlock on
i_size update on 32bit smp) and a fall-through warning cleanup"
* tag '9p-for-5.1' of git://github.com/martinetd/linux:
9p/net: fix memory leak in p9_client_create
9p: use inode->i_lock to protect i_size_write() under 32-bit
9p: mark expected switch fall-through
|
|
Fixes: 400816f60c54 ("perf/x86/intel: Implement support for TSX Force Abort")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: kbuild-all@01.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190313184243.GA10820@lkp-sb-ep06
|
|
When this .gitignore was added, lxdialog was an independent hostprogs-y.
Now that all objects in lxdialog/ are directly linked to mconf, the
lxdialog is no longer generated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The generic-y is redundant under the following condition:
- arch has its own implementation
- the same header is added to generated-y
- the same header is added to mandatory-y
If a redundant generic-y is found, the warning like follows is displayed:
scripts/Makefile.asm-generic:20: redundant generic-y found in arch/arm/include/asm/Kbuild: timex.h
I fixed up arch Kbuild files found by this.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit caf6fe91ddf62a96401e21e9b7a07227440f4185.
The commit was fine but is no longer needed as of commit 3a2429e1faf4
("kbuild: change if_changed_rule for multi-line recipe"). Let's go
back to using ";" to be consistent.
For some discussion, see:
https://lkml.kernel.org/r/CAK7LNASde0Q9S5GKeQiWhArfER4S4wL1=R_FW8q0++_X3T5=hQ@mail.gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
During a simple no-op (nothing changed) build I saw 39 invocations of
the C compiler with the argument "-print-file-name=include". We don't
need to call the C compiler 39 times for this--one time will suffice.
Let's change NOSTDINC_FLAGS to a simply expanded variable to avoid
this since there doesn't appear to be any reason it should be
recursively expanded.
On my build this shaved ~400 ms off my "no-op" build.
Note that the recursive expansion seems to date back to the (really
old) commit e8f5bdb02ce0 ("[PATCH] Makefile include path ordering").
It's a little unclear to me if the point of that patch was to switch
the variable to be recursively expanded (which it did) or to avoid
directly assigning to NOSTDINC_FLAGS (AKA to switch to +=) because
someone else (out of tree?) was setting it. I presume later since if
the only goal was to switch to recursive expansion the patch would
have just removed the ":".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
* The man page for dpkg-source(1) notes:
> -b, --build directory [format-specific-parameters]
> Build a source package (--build since dpkg 1.17.14).
> <...>
>
> dpkg-source will build the source package with the first
> format found in this ordered list: the format indicated
> with the --format command line option, the format
> indicated in debian/source/format, “1.0”. The fallback
> to “1.0” is deprecated and will be removed at some point
> in the future, you should always document the desired
> source format in debian/source/format. See section
> SOURCE PACKAGE FORMATS for an extensive description of
> the various source package formats.
Thus it would be more foolproof to explicitly use 1.0 (as we always
did) than to rely on dpkg-source's defaults.
* In a similar vein, debian/rules is not made executable by mkdebian,
and dpkg-source warns about that but still silently fixes the file.
Let's be explicit once again.
Signed-off-by: Arseny Maslennikov <ar@cs.msu.ru>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
The implementation of this semantic code search is:
In a function, for a local variable returned by calling
of_find_device_by_node(),
a, if it is released by a function such as
put_device()/of_dev_put()/platform_device_put() after the last use,
it is considered that there is no reference leak;
b, if it is passed back to the caller via
dev_get_drvdata()/platform_get_drvdata()/get_device(), etc., the
reference will be released in other functions, and the current function
also considers that there is no reference leak;
c, for the rest of the situation, the current function should release the
reference by calling put_device, this code search will report the
corresponding error message.
By using this semantic code search, we have found some object reference leaks,
such as:
commit 11907e9d3533 ("ASoC: fsl-asoc-card: fix object reference leaks in
fsl_asoc_card_probe")
commit a12085d13997 ("mtd: rawnand: atmel: fix possible object reference leak")
commit 11493f26856a ("mtd: rawnand: jz4780: fix possible object reference leak")
There are still dozens of reference leaks in the current kernel code.
Further, for the case of b, the object returned to other functions may also
have a reference leak, we will continue to develop other cocci scripts to
further check the reference leak.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd system call from Christian Brauner:
"This introduces the ability to use file descriptors from /proc/<pid>/
as stable handles on struct pid. Even if a pid is recycled the handle
will not change. For a start these fds can be used to send signals to
the processes they refer to.
With the ability to use /proc/<pid> fds as stable handles on struct
pid we can fix a long-standing issue where after a process has exited
its pid can be reused by another process. If a caller sends a signal
to a reused pid it will end up signaling the wrong process.
With this patchset we enable a variety of use cases. One obvious
example is that we can now safely delegate an important part of
process management - sending signals - to processes other than the
parent of a given process by sending file descriptors around via scm
rights and not fearing that the given process will have been recycled
in the meantime. It also allows for easy testing whether a given
process is still alive or not by sending signal 0 to a pidfd which is
quite handy.
There has been some interest in this feature e.g. from systems
management (systemd, glibc) and container managers. I have requested
and gotten comments from glibc to make sure that this syscall is
suitable for their needs as well. In the future I expect it to take on
most other pid-based signal syscalls. But such features are left for
the future once they are needed.
This has been sitting in linux-next for quite a while and has not
caused any issues. It comes with selftests which verify basic
functionality and also test that a recycled pid cannot be signaled via
a pidfd.
Jon has written about a prior version of this patchset. It should
cover the basic functionality since not a lot has changed since then:
https://lwn.net/Articles/773459/
The commit message for the syscall itself is extensively documenting
the syscall, including it's functionality and extensibility"
* tag 'pidfd-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
selftests: add tests for pidfd_send_signal()
signal: add pidfd_send_signal() syscall
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull device-dax updates from Dan Williams:
"New device-dax infrastructure to allow persistent memory and other
"reserved" / performance differentiated memories, to be assigned to
the core-mm as "System RAM".
Some users want to use persistent memory as additional volatile
memory. They are willing to cope with potential performance
differences, for example between DRAM and 3D Xpoint, and want to use
typical Linux memory management apis rather than a userspace memory
allocator layered over an mmap() of a dax file. The administration
model is to decide how much Persistent Memory (pmem) to use as System
RAM, create a device-dax-mode namespace of that size, and then assign
it to the core-mm. The rationale for device-dax is that it is a
generic memory-mapping driver that can be layered over any "special
purpose" memory, not just pmem. On subsequent boots udev rules can be
used to restore the memory assignment.
One implication of using pmem as RAM is that mlock() no longer keeps
data off persistent media. For this reason it is recommended to enable
NVDIMM Security (previously merged for 5.0) to encrypt pmem contents
at rest. We considered making this recommendation an actively enforced
requirement, but in the end decided to leave it as a distribution /
administrator policy to allow for emulation and test environments that
lack security capable NVDIMMs.
Summary:
- Replace the /sys/class/dax device model with /sys/bus/dax, and
include a compat driver so distributions can opt-in to the new ABI.
- Allow for an alternative driver for the device-dax address-range
- Introduce the 'kmem' driver to hotplug / assign a device-dax
address-range to the core-mm.
- Arrange for the device-dax target-node to be onlined so that the
newly added memory range can be uniquely referenced by numa apis"
NOTE! I'm not entirely happy with the whole "PMEM as RAM" model because
we currently have special - and very annoying rules in the kernel about
accessing PMEM only with the "MC safe" accessors, because machine checks
inside the regular repeat string copy functions can be fatal in some
(not described) circumstances.
And apparently the PMEM modules can cause that a lot more than regular
RAM. The argument is that this happens because PMEM doesn't necessarily
get scrubbed at boot like RAM does, but that is planned to be added for
the user space tooling.
Quoting Dan from another email:
"The exposure can be reduced in the volatile-RAM case by scanning for
and clearing errors before it is onlined as RAM. The userspace tooling
for that can be in place before v5.1-final. There's also runtime
notifications of errors via acpi_nfit_uc_error_notify() from
background scrubbers on the DIMM devices. With that mechanism the
kernel could proactively clear newly discovered poison in the volatile
case, but that would be additional development more suitable for v5.2.
I understand the concern, and the need to highlight this issue by
tapping the brakes on feature development, but I don't see PMEM as RAM
making the situation worse when the exposure is also there via DAX in
the PMEM case. Volatile-RAM is arguably a safer use case since it's
possible to repair pages where the persistent case needs active
application coordination"
* tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: "Hotplug" persistent memory for use like normal RAM
mm/resource: Let walk_system_ram_range() search child resources
mm/memory-hotplug: Allow memory resources to be children
mm/resource: Move HMM pr_debug() deeper into resource code
mm/resource: Return real error codes from walk failures
device-dax: Add a 'modalias' attribute to DAX 'bus' devices
device-dax: Add a 'target_node' attribute
device-dax: Auto-bind device after successful new_id
acpi/nfit, device-dax: Identify differentiated memory with a unique numa-node
device-dax: Add /sys/class/dax backwards compatibility
device-dax: Add support for a dax override driver
device-dax: Move resource pinning+mapping into the common driver
device-dax: Introduce bus + driver model
device-dax: Start defining a dax bus model
device-dax: Remove multi-resource infrastructure
device-dax: Kill dax_region base
device-dax: Kill dax_region ida
|
|
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
|
|
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
|
