| Age | Commit message (Collapse) | Author |
|---|
|
The DMA is a function 0 of the multifunction device where SPI host is attached.
Thus, we may avoid to hardcode PCI slot number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Just a simple cleanup of init_timer with setting the fields manually.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 9da433c0a0b5f71ac92dc9dca778295649675f08.
Vineet writes:
Could you please revert this single patch from tty-next for 3.17 as the
needed core changes are not yet finalized.
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The s->clk never gets setup in sc16is7xx_probe() and instead was using a
local clk variable, but then testing the uninitialized s->clk during
teardown
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8250_dw driver fails to probe if the specified clock isn't
registered at probe time. Even if a clock frequency is given,
the required clock might be gated because it wasn't properly
enabled.
This happened to me when the device is registered through DT,
and the clock was part of an MFD, the PRCM found on A31 and A23
SoCs. Unlike core clocks that are registered with OF_CLK_DECLARE,
which happen almost immediately after the kernel starts, the
clocks are registered as sub-devices of the PRCM MFD platform
device. Even though devices are registered in the order they are
found in the DT, the drivers are registered in a different,
arbitrary order. It is possible that the 8250_dw driver is
registered, and thus associated with the device and probed, before
the clock driver is registered and probed.
8250_dw then reports unable to get the clock, and fails. Without
a working console, the kernel panics.
This patch adds support for deferred probe handling for the clock
and reset controller. It also fixes the cleanup path if
serial8250_register_8250_port fails.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Allwinner A31 and A23 SoCs have a reset controller
maintaining the UART in reset by default.
This patch adds optional reset support to the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the current calculation, if the required baud rate is above 262143,
we get an overflow.
This patch uses a 64bits variable to do the maths.
Also, we remove the '+1' to avoid a divide by zero if the input clock
rate is something unexpected.
Indeed, if the input clock rate is zero, it is preferable to be notified,
since the UART won't work anyway.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to prevent an asc instance to be used as early console, BUG_ON is
used on either mapbase or membase being NULL.
Problem is that this condition is also true when we set console to be a ttyASx
different to the first asc instance being probed.
Instead of calling BUG_ON, it now returns -ENXIO when either mapbase or
membase is NULL.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gsm->num is the index of gsm_mux[], it's invalid before calling gsm_activate_mux.
Signed-off-by: xinhui.pan <xinhuiX.pan@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current code allocates too much data for tty_groups member of uart_port struct,
so fix it.
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dma_{un}map_* uses 'enum dma_data_direction' not 'enum dma_transfer_direction'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 3d1c90d48cbe335a ("serial: altera_jtaguart: Adpot
uart_console_write()") introduced the usage of uart_console_write() but
didn't change the signature of altera_jtaguart_console_putc() to take a
pointer to struct uart_port instead of struct console, breaking the
driver's console support and leading to the following warning:
> drivers/tty/serial/altera_jtaguart.c: In function 'altera_jtaguart_console_write':
> >> drivers/tty/serial/altera_jtaguart.c:350:2: warning: passing argument 4 of 'uart_console_write' from incompatible pointer type [enabled by default]
> uart_console_write(port, s, count, altera_jtaguart_console_putc);
> ^
> In file included from drivers/tty/serial/altera_jtaguart.c:25:0:
> include/linux/serial_core.h:317:6: note: expected 'void (*)(struct uart_port *, int)' but argument is of type 'void (*)(struct console *, int)'
> void uart_console_write(struct uart_port *port, const char *s,
Fix this by adjusting the signature of altera_jtaguart_console_putc()
accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add tunable RX interrupt trigger I/F of FIFO buffers.
Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.
According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.
This patch makes some devices change RX interrupt trigger from userland.
<How to use>
- Read current setting
# cat /sys/class/tty/ttyS0/rx_trig_bytes
8
- Write user setting
# echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
# cat /sys/class/tty/ttyS0/rx_trig_bytes
1
<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)
<Change log>
Changes in V9:
- Use attr_group instead of dev_spec_attr_group of uart_port structure
Changes in V8:
- Divide this patch from V7's patch based on Greg's comment
Changes in V7:
- Add Documentation
- Change I/F name from rx_int_trig to rx_trig_bytes because the name
rx_int_trig is hard to understand how users specify the value
Changes in V6:
- Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
UART_FCR_R_TRIG_BITS()
- Change following function names:
convert_fcr2val() => fcr_get_rxtrig_bytes()
convert_val2rxtrig() => bytes_to_fcr_rxtrig()
- Fix typo in serial8250_do_set_termios()
- Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
- Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
(but UI remains rx_int_trig)
- Change the meaningless variable name 'val' to 'bytes' following functions:
fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
- Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
fcr_get_rxtrig_bytes()
- Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
in register_dev_spec_attr_grp()
- Delete the checking whether a user changed FCR or not when minimum buffer
is needed in serial8250_do_set_termios()
Changes in V5.1:
- Fix FCR_RX_TRIG_MAX_STATE definition
Changes in V5:
- Support Tegra, 16650V2, 16654, and 16750
- Store default FCR value to up->fcr when the port is first created
- Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
in convert_fcr2val() and convert_val2rxtrig()
Changes in V4:
- Introduce fifo_bug flag in uart_8250_port structure
This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
for up->bugs. If this flag is enabled, user cannot set RX trigger.
- Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
at convert_val2rxtrig()
- Set the nearest lower RX trigger when users input a meaningless value at
convert_val2rxtrig()
- Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
- Set fcr = up->fcr in the begging of serial8250_do_set_termios()
Changes in V3:
- Change I/F from ioctl(2) to sysfs(rx_int_trig)
Changed in V2:
- Use _IOW for TIOCSFIFORTRIG definition
- Pass the interrupt trigger value itself
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some serial drivers (like 8250), want to add sysfs files. We need to do
so in a race-free way, so allow any port to be able to specify an
attribute group that should be added at device creation time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At present it is not possible to boot with the ttyNMI0 console treating
character input normally, instead character input triggers a prompt
telling the user how to trigger the knock detector and enter the
debugger. To use the console normally requires that kdb be entered and
the nmi_console command be used to enable the console (or if only kgdb
is present then gdb must directly manipulate the value of
kgdb_nmi_tty_enabled).
This patch automates the management of kgdb_nmi_tty_enabled by keeping
track of the number of file handles that are open for reading and using
that to determine how to tty should operate.
The approach means that:
1. Behaviour before init starts is unchanged.
2. If the userspace runs a getty or some other interactive process on
/dev/console (or explicitly on /dev/ttyNMI0) the tty will treat
character input like any other tty.
3. If the userspace doesn't use /dev/console or if it uses /dev/console
only to log messages (O_WRONLY) then the user prompt is retained.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Follow commit 2970b7f5ea3c ("serial: altera: Adopt
uart_console_write()") and don't open code the LF to LFCR conversion in
altera_jtaguart either. Use uart_console_write() instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The of_node is derived from pdev for every usage, define a
device_node variable instead.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The cases should comes before default in a switch.
Even if we want the case and default to share same code.
Its good to define the case first followed by default.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UART modules on some SoCs only differ in the fifosize of each
UART channel. Its useless to duplicate the drv_data structure
or create a compatible name for such a change.
We can get fifosize via the device tree nodes (not mandating it).
Also updates the documentation.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It helps to cast struct uart_port to struct uart_8250_port at runtime.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This add the 32-bit register version LPUART support with big-endian
byte order.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
use exact SoC revision instead of wildcard describing
to make the binding more clearer.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the error of the same bit rate is detected, we will need to select
the recive margin is large. Current code holds the minimum error, it does
not have to check the recive margin. This adds this calculation.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If bit-rate calculation result of HSCIF is expect 255 from 0,
driver does not calculate error bit. However, we need to round
the value to calculate error bit in the case of negative value.
This rounds the value of bit-rate using clamp(), and bit-rate is the
case of negative value, it enables the calculation of the error bit.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the decimal point is discarded calculation of BRR.
Therefore, it can not calculate a value close to the correct value.
This patch fixes this problem by using DIV_ROUND_CLOSEST.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want those fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"More bug fixes for ext4 -- most importantly, a fix for a bug
introduced in 3.15 that can end up triggering a file system corruption
error after a journal replay.
It shouldn't lead to any actual data corruption, but it is scary and
can force file systems to be remounted read-only, etc"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix potential null pointer dereference in ext4_free_inode
ext4: fix a potential deadlock in __ext4_es_shrink()
ext4: revert commit which was causing fs corruption after journal replays
ext4: disable synchronous transaction batching if max_batch_time==0
ext4: clarify ext4_error message in ext4_mb_generate_buddy_error()
ext4: clarify error count warning messages
ext4: fix unjournalled bg descriptor while initializing inode bitmap
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"This batch of fixes is for a handful of clock drivers from Allwinner,
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that
did not boot under certain configurations. Other fixes are the result
of changes to the clock core introduced in 3.15 that had subtle
impacts on the clock drivers.
There are no fixes to the clock framework core in this pull request"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: spear3xx: Set proper clock parent of uart1/2
clk: spear3xx: Use proper control register offset
clk: qcom: HDMI source sel is 3 not 2
clk: sunxi: fix devm_ioremap_resource error detection code
clk: s2mps11: Fix double free corruption during driver unbind
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: exynos5420: Remove aclk66_peric from the clock tree description
clk/exynos5250: fix bit number for tv sysmmu clock
clk: s3c64xx: Hookup SPI clocks correctly
clk: samsung: exynos4: Remove SRC_MASK_ISP gates
clk: samsung: add more aliases for s3c24xx
clk: samsung: fix several typos to fix boot on s3c2410
clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: ti: dra7: return error code in failure case
clk: ti: apll: not allocating enough data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- Another set of OMAP fixes
* Clock fixes
* Restart handling
* PHY regulators
* SATA hwmod data for DRA7
+ Some trivial fixes and removal of a bit of dead code
- Exynos fixes
* A bunch of clock fixes
* Some SMP fixes
* Exynos multi-core timer: register as clocksource and fix ftrace.
+ a few other minor fixes
There's also a couple more patches, and at91 fix for USB caused by
common clock conversion, and more MAINTAINERS entries for shmobile.
We're definitely switching to only regression fixes from here on out,
we've been a little less strict than usual up until now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: at91: at91sam9x5: add clocks for usb device
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: imx: fix shared gate clock
ARM: dts: Update the parent for Audss clocks in Exynos5420
ARM: EXYNOS: Update secondary boot addr for secure mode
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
...
|
|
Pull ARM fixes from Russell King:
"Another round of fixes for ARM:
- a set of kprobes fixes from Jon Medhurst
- fix the revision checking for the L2 cache which wasn't noticed to
have been broken"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: l2c: fix revision checking
ARM: kprobes: Fix test code compilation errors for ARMv4 targets
ARM: kprobes: Disallow instructions with PC and register specified shift
ARM: kprobes: Prevent known test failures stopping other tests running
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Fix for a boot regression introduced in v3.16-rc1,
- Fix for a build issue in -next"
Christoph Hellwig questioned why mach_random_get_entropy should be
exported to modules, and Geert explains that random_get_entropy() is
called by at least the crypto layer and ends up using it on m68k. On
most other architectures it just uses get_cycles() (which is typically
inlined and doesn't need exporting),
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Export mach_random_get_entropy to modules
m68k: Fix boot regression on machines with RAM at non-zero
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"The major patch in here is one which fixes the fanotify_mark() syscall
in the compat layer of the 64bit parisc kernel. It went unnoticed so
long, because the calling syntax when using a 64bit parameter in a
32bit syscall is quite complex and even worse, it may be even
different if you call syscall() or the glibc wrapper. This patch
makes the kernel accept the calling convention when called by the
glibc wrapper.
The other two patches are trivial and remove unused headers, #includes
and adds the serial ports of the fastest C8000 workstation to the
parisc-kernel internal hardware database"
* 'parisc-3.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: drop unused defines and header includes
parisc: fix fanotify_mark() syscall on 32bit compat kernel
parisc: add serial ports of C8000/1GHz machine to hardware database
|
|
The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.
Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62c (SPEAr: Switch to common clock framework).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+
|
|
On parisc we can not use the existing compat implementation for fanotify_mark()
because for the 64bit mask parameter the higher and lower 32bits are ordered
differently than what the compat function expects from big endian
architectures.
Specifically:
It finally turned out, that on hppa we end up with different assignments
of parameters to kernel arguments depending on if we call the glibc
wrapper function
int fanotify_mark (int __fanotify_fd, unsigned int __flags,
uint64_t __mask, int __dfd, const char *__pathname);
or directly calling the syscall manually
syscall(__NR_fanotify_mark, ...)
Reason is, that the syscall() function is implemented as C-function and
because we now have the sysno as first parameter in front of the other
parameters the compiler will unexpectedly add an empty paramenter in
front of the u64 value to ensure the correct calling alignment for 64bit
values.
This means, on hppa you can't simply use syscall() to call the kernel
fanotify_mark() function directly, but you have to use the glibc
function instead.
This patch fixes the kernel in the hppa-arch specifc coding to adjust
the parameters in a way as if userspace calls the glibc wrapper function
fanotify_mark().
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"We have two small fixes. First one from Daniel to handle 0-length
packets for usb cppi dma. Second by Russell for imx-sdam cyclic
residue reporting"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
Update imx-sdma cyclic handling to report residue
dma: cppi41: handle 0-length packets
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:
Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: dts: Update the parent for Audss clocks in Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In 2c964a2f "drivers: tty: Merge alloc_tty_struct and
initialize_tty_struct", I messed up the refactorization of
pty_common_install, causing use-after-free and NULL pointer derefs on
various error paths. This should fix it.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids"
* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
phy: core: Fix error path in phy_create()
drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
phy: omap-usb2: fix devm_ioremap_resource error detection code
phy: sun4i: depend on RESET_CONTROLLER
USB: serial: ftdi_sio: Add Infineon Triboard
USB: ftdi_sio: Add extra PID.
usb: option: Add ID for Telewell TW-LTE 4G v2
USB: cp210x: add support for Corsair usb dongle
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small serial fixes that resolve some reported problems
that started in 3.15 with some serial drivers.
And there's a new dt binding for a serial driver, which was all that
was needed for the renesas serial driver"
* tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0
serial: imx: Fix build breakage
serial: arc_uart: Use uart_circ_empty() for open-coded comparison
serial: Test for no tx data on tx restart
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two hyperv driver fixes, and one i8k driver fix for 3.16"
* tag 'char-misc-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
i8k: Fix non-SMP operation
Drivers: hv: util: Fix a bug in the KVP code
Drivers: hv: vmbus: Fix a bug in the channel callback dispatch code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are some IIO driver fixes for 3.16-rc5. Nothing major, just
resolves some minor issues that have been reported"
* tag 'staging-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: ti_am335x_adc: Fix: Use same step id at FIFOs both ends
iio:tcs3472: Check for buffer enabled and locking
iio: hid-sensor-prox: Fix return values
iio: hid-sensor-gyro-3d: Fix return values
iio: hid-sensor-als: Fix return values
iio: hid-sensor-magn-3d: Fix return values
iio: hid-sensor-accel-3d: Fix return values
iio: hid-sensor-press: Fix return values
|
|
Fix potential null pointer dereferencing problem caused by e43bb4e612
("ext4: decrement free clusters/inodes counters when block group declared bad")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
|
|
This fixes the following lockdep complaint:
[ INFO: possible circular locking dependency detected ]
3.16.0-rc2-mm1+ #7 Tainted: G O
-------------------------------------------------------
kworker/u24:0/4356 is trying to acquire lock:
(&(&sbi->s_es_lru_lock)->rlock){+.+.-.}, at: [<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0
but task is already holding lock:
(&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180
which lock already depends on the new lock.
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ei->i_es_lock);
lock(&(&sbi->s_es_lru_lock)->rlock);
lock(&ei->i_es_lock);
lock(&(&sbi->s_es_lru_lock)->rlock);
*** DEADLOCK ***
6 locks held by kworker/u24:0/4356:
#0: ("writeback"){.+.+.+}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560
#1: ((&(&wb->dwork)->work)){+.+.+.}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560
#2: (&type->s_umount_key#22){++++++}, at: [<ffffffff811a9c74>] grab_super_passive+0x44/0x90
#3: (jbd2_handle){+.+...}, at: [<ffffffff812979f9>] start_this_handle+0x189/0x5f0
#4: (&ei->i_data_sem){++++..}, at: [<ffffffff81247062>] ext4_map_blocks+0x132/0x550
#5: (&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180
stack backtrace:
CPU: 0 PID: 4356 Comm: kworker/u24:0 Tainted: G O 3.16.0-rc2-mm1+ #7
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: writeback bdi_writeback_workfn (flush-253:0)
ffffffff8213dce0 ffff880014b07538 ffffffff815df0bb 0000000000000007
ffffffff8213e040 ffff880014b07588 ffffffff815db3dd ffff880014b07568
ffff880014b07610 ffff88003b868930 ffff88003b868908 ffff88003b868930
Call Trace:
[<ffffffff815df0bb>] dump_stack+0x4e/0x68
[<ffffffff815db3dd>] print_circular_bug+0x1fb/0x20c
[<ffffffff810a7a3e>] __lock_acquire+0x163e/0x1d00
[<ffffffff815e89dc>] ? retint_restore_args+0xe/0xe
[<ffffffff815ddc7b>] ? __slab_alloc+0x4a8/0x4ce
[<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
[<ffffffff810a8707>] lock_acquire+0x87/0x120
[<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
[<ffffffff8128592d>] ? ext4_es_free_extent+0x5d/0x70
[<ffffffff815e6f09>] _raw_spin_lock+0x39/0x50
[<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
[<ffffffff8119760b>] ? kmem_cache_alloc+0x18b/0x1a0
[<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0
[<ffffffff812869b8>] ext4_es_insert_extent+0xc8/0x180
[<ffffffff812470f4>] ext4_map_blocks+0x1c4/0x550
[<ffffffff8124c4c4>] ext4_writepages+0x6d4/0xd00
...
Reported-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Minchan Kim <minchan@kernel.org>
Cc: stable@vger.kernel.org
Cc: Zheng Liu <gnehzuil.liu@gmail.com>
|
|
Dell kernel driver dell-smo8800 provides same freefall interface as hp_accel so
program hpfall.c works also on Dell laptops. So rename it to freefall.c.
Dell driver does not provide hp::hddprotect led so make sure that freefall.c
works also if hp::hddprotect does not exist in sysfs.
Additionally write info to syslog.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Sonal Santan <sonal.santan@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixed spelling typo in various template files
within Documentation/Docbook.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
