| Age | Commit message (Collapse) | Author |
|---|
|
With this patch changes relevant to a node's own multicast flags are
printed to the 'mcast' log level.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
With this patch we are finally able to support multicast optimizations
in bridged setups, too. So far, if a bridge was added on top of a
soft-interface (e.g. bat0) the batman-adv multicast optimizations
needed to be disabled to avoid packetloss.
Current Linux bridge implementations and API can now provide us
with the so far missing information about interested but "remote"
multicast receivers behind bridge ports.
The Linux bridge performs the detection of remote participants
interested in multicast packets with its own and mature so
called IGMP and MLD snooping code and stores that in its
database. With the new API provided by the bridge batman-adv can
now simply hook into this database.
We then reliably announce the gathered multicast listeners to
other nodes through the batman-adv translation table.
Additionally, the Linux bridge provides us with the information about
whether an IGMP/MLD querier exists. If there is none then we need to
disable multicast optimizations as we cannot learn about multicast
listeners on external, bridged-in host then.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
With this patch IGMP or MLD reports are always flooded. This is
necessary for the upcoming bridge integration to function without
multicast packet loss.
With the report handling so far bridges might miss interested multicast
listeners, leading to wrongly excluding ports from multicast packet
forwarding.
Currently we are treating IGMP/MLD reports, the messages bridges use to
learn about interested multicast listeners, just as any other multicast
packet: We try to send them to nodes matching its multicast destination.
Unfortunately, the destination address of reports of the older
IGMPv2/MLDv1 protocol families do not strictly adhere to their own
protocol: More precisely, the interested receiver, an IGMPv2 or MLDv1
querier, itself usually does not listen to the multicast destination
address of any reports.
Therefore with this patch we are simply excluding IGMP/MLD reports from
the multicast forwarding code path and keep flooding them. By that
any bridge receives them and can properly learn about listeners.
To avoid compatibility issues with older nodes not yet implementing this
report handling, we need to force them to flood reports: We do this by
bumping the multicast TVLV version to 2, effectively disabling their
multicast optimization.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Unfragmented frames which traverse a node have their skb->priority set
by looking at the IP ToS byte, or the 802.1p header. However for
fragments this is not possible, only one of the fragments will contain
the headers. Instead, place the priority into the fragment header and
on receiving a fragment, use this information to set the skb->priority
for when the fragment is forwarded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
BATMAN will set the skb->priority based on the IP precedence or 802.1q
tag. However, if it needs to fragment the frame, it currently leaves
the fragment skb with the default priority and actually overwrites the
priority in the unfragmented frame. Fix this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The ELP interval and throughput override interface settings are initialized
with default settings on every time an interface is added to a mesh.
This patch prevents this behavior by moving the configuration init to the
interface detection routine which runs only once per interface.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[a@unstable.cc: move initialization to batadv_v_hardif_init]
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
To reduce the field pollution in our main batadv_priv data structure
we've already created some substructures so that we could group fields
in a convenient manner.
However gw_mode and gw_sel_class are still part of the main object.
More both fields to the GW private substructure.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
the compiler can optimize functions within the same C file and therefore
there is no need to make it explicit.
Remove the useless inline attribute for __batadv_store_uint_attr()
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The ogm_emit and ogm_schedule API calls were rather tight to the
B.A.T.M.A.N. IV logic and therefore rather difficult to use
with other algorithm implementations.
Remove such calls and move the surrounding logic into the
B.A.T.M.A.N. IV specific code.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Also update obsolete email address.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
To make it easier to search through the code it is better to print static
strings directly instead of using format strings printing constants.
This was addressed in a previous patch, but the Gateway table header
was not updated accordingly.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
|
sch_atm returns this when TC_ACT_SHOT classification occurs.
But all other schedulers that use tc_classify
(htb, hfsc, drr, fq_codel ...) return NET_XMIT_SUCCESS | __BYPASS
in this case so just do that in atm.
BATMAN uses it as an intermediate return value to signal
forwarding vs. buffering, but it did not return POLICED to
callers outside of BATMAN.
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since msleep is based on jiffies the PHY reset could take longer
than expected. So use msleep for values greater than 20 msec otherwise
usleep_range.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.
Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
net_sched: remove qdisc_is_throttled()
HTB, CBQ and HFSC pay a very high cost updating the qdisc 'throttled'
status that nothing but CBQ seems to use.
CBQ usage is flaky anyway, since no qdisc ->enqueue() updates the
'throttled' qdisc status.
This looks like some 'optimization' that actually cost more than code
without the optimization, and might cause latency issues with CBQ.
In my tests, I could achieve a 8 % performance increase in TCP_RR
workload through HTB qdisc, in presence of throttled classes,
and 5 % without throttled classes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__QDISC_STATE_THROTTLED bit manipulation is rather expensive
for HTB and few others.
I already removed it for sch_fq in commit f2600cf02b5b
("net: sched: avoid costly atomic operation in fq_dequeue()")
and so far nobody complained.
When one ore more packets are stuck in one or more throttled
HTB class, a htb dequeue() performs two atomic operations
to clear/set __QDISC_STATE_THROTTLED bit, while root qdisc
lock is held.
Removing this pair of atomic operations bring me a 8 % performance
increase on 200 TCP_RR tests, in presence of throttled classes.
This patch has no side effect, since nothing actually uses
disc_is_throttled() anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like it is only there as some optimization attempt.
Since __QDISC_STATE_THROTTLED set/unset is way too expensive,
and netem is the last user, just remove this check.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far no qdisc ever unset the throttled bit at enqueue() time,
so CBQ usage of qdisc_is_throttled() was flaky.
Since __QDISC_STATE_THROTTLED set/unset is way too expensive
considering that only CBQ was eventually caring for this status,
it would make sense to implement a Qdisc ops ->is_throttled()
if we find that this is needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to get rid of generic qdisc throttled management,
so this qdisc has to use a private flag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pramod Kumar says:
====================
Add MDIO bus multiplexer support for iProc SoCs
Broadcom iProc based SoCs use a MDIO bus multiplexer where child buses
could be internal as well external to SoCs. These buses could supports
MDIO transaction compatible to C-22/C-45.
Broadcom MDIO bus multiplexer is an integrated multiplexer where child bus
selection and mdio transaction logic lies inside multiplexer itself.
To accommodate this multiplexer in existing mux framework below changes
were required-
1. Passed MDIO parent bus via mdio_mux_init to MDIO mux framework.
This patch set includes MDIO bus multiplexer driver along with above
framework change. It includes one external bus node having Ethernet PHY
attached and two internal bus node holding PCIe PHYs.
This patch series is based on v4.7-rc1 and is available from github-
repo: https://github.com/Broadcom/arm64-linux.git
branch:mdio-mux-v5
-Changes from v4:
- disabled PCIe PHYs from dtsi and enabled in dts file.
-Changes from v3:
- Unregister and free the parent MDIO bus.
- rebased on net-next/master branch.
Reason for resend:
-Rebased on v4.7-rc1
Changes from v2:
-Addressed Rob's comments in this patch regarding typo/grammers.
-Addressed David's comments regarding local variables order.
-Removed property "mdio-integrated-mux" and used mdiobus_register()
in place of of_mdiobus_regsiter().
-removed usage of IS_ERR_OR_NULL to IS_ERR in PCIe PHY driver.
Changes from v1:
- stop using "brcm,is_c45" from bus node as suggested by Andrew. MDIO
PHY driver will logically OR MII_ADDR_C45 into the address when issues
any C45 MDIO read/write transaction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add PCI Phy support for Broadcom Northstar2 SoCs. This driver uses the
interface from the iproc mdio mux driver to enable the devices
respective phys.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Binding doc for NS2 PCIe PHYs.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
iProc based SoCs supports the integrated mdio multiplexer which
has the bus selection as well as mdio transaction generation logic
inside.
This multiplexer has child buses for PCIe, SATA, USB and ETH. These
buses could be internal or external to SOC where PHYs are attached.
These buses could use C-45 or C-22 mdio transaction.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add integrated MDIO multiplexer driver node which contains
two mux PCIe bus and one ethernet bus along with phys
lying on these bus.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DT binding doc for Broadcom MDIO bus multiplexer driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change "mdio-parent-bus" from mandatory section to optional
as it won't be required by integrated MDIO multiplexer
which has bus selection and mdio transaction generation logic,
integrated inside.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An integrated multiplexer uses same address space for
"muxed bus selection" and "generation of mdio transaction"
hence its good to register parent bus from mux driver.
Hence added a mechanism where mux driver could register a
parent bus and pass it down to framework via mdio_mux_init api.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now sctp doesn't change socket state upon shutdown reception. It changes
just the assoc state, even though it's a TCP-style socket.
For some cases, if we really need to check sk->sk_state, it's necessary to
fix this issue, at least when we use ss or netstat to dump, we can get a
more exact information.
As an improvement, we will change sk->sk_state when we change asoc->state
to SHUTDOWN_RECEIVED, and also do it in sctp_shutdown to keep consistent
with sctp_close.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the next cycle, we have the following:
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Zi Shen Lim says:
====================
arm64 BPF JIT updates
Updates for arm64 eBPF JIT.
The main addition here is implementation of bpf_tail_call.
Changes since v2:
- None. Resubmit per David Miller.
Changes since v1:
- Added patch #1 to address build error due to missing header inclusion
in linux/bpf.h. (Thanks to suggestion and ack by Daniel Borkmann)
Ordered it ahead of bpf_tail_call patch #2 so build error is not
triggered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove superfluous stack frame, saving us 3 instructions for every
LD_ABS or LD_IND.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove superfluous stack frame, saving us 3 instructions for
every JMP_CALL.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for JMP_CALL_X (tail call) introduced by commit 04fd61ab36ec
("bpf: allow bpf programs to tail-call other bpf programs").
bpf_tail_call() arguments:
ctx - context pointer passed to next program
array - pointer to map which type is BPF_MAP_TYPE_PROG_ARRAY
index - index inside array that selects specific program to run
In this implementation arm64 JIT jumps into callee program after prologue,
so callee program reuses the same stack. For tail_call_cnt, we use the
callee-saved R26 (which was already saved/restored but previously unused
by JIT).
With this patch a tail call generates the following code on arm64:
if (index >= array->map.max_entries)
goto out;
34: mov x10, #0x10 // #16
38: ldr w10, [x1,x10]
3c: cmp w2, w10
40: b.ge 0x0000000000000074
if (tail_call_cnt > MAX_TAIL_CALL_CNT)
goto out;
tail_call_cnt++;
44: mov x10, #0x20 // #32
48: cmp x26, x10
4c: b.gt 0x0000000000000074
50: add x26, x26, #0x1
prog = array->ptrs[index];
if (prog == NULL)
goto out;
54: mov x10, #0x68 // #104
58: ldr x10, [x1,x10]
5c: ldr x11, [x10,x2]
60: cbz x11, 0x0000000000000074
goto *(prog->bpf_func + prologue_size);
64: mov x10, #0x20 // #32
68: ldr x10, [x11,x10]
6c: add x10, x10, #0x20
70: br x10
74:
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0fc174dea545 ("ebpf: make internal bpf API independent of
CONFIG_BPF_SYSCALL ifdefs") introduced usage of ERR_PTR() in
bpf_prog_get(), however did not include linux/err.h.
Without this patch, when compiling arm64 BPF without CONFIG_BPF_SYSCALL:
...
In file included from arch/arm64/net/bpf_jit_comp.c:21:0:
include/linux/bpf.h: In function 'bpf_prog_get':
include/linux/bpf.h:235:9: error: implicit declaration of function 'ERR_PTR' [-Werror=implicit-function-declaration]
return ERR_PTR(-EOPNOTSUPP);
^
include/linux/bpf.h:235:9: warning: return makes pointer from integer without a cast [-Wint-conversion]
In file included from include/linux/rwsem.h:17:0,
from include/linux/mm_types.h:10,
from include/linux/sched.h:27,
from arch/arm64/include/asm/compat.h:25,
from arch/arm64/include/asm/stat.h:23,
from include/linux/stat.h:5,
from include/linux/compat.h:12,
from include/linux/filter.h:10,
from arch/arm64/net/bpf_jit_comp.c:22:
include/linux/err.h: At top level:
include/linux/err.h:23:35: error: conflicting types for 'ERR_PTR'
static inline void * __must_check ERR_PTR(long error)
^
In file included from arch/arm64/net/bpf_jit_comp.c:21:0:
include/linux/bpf.h:235:9: note: previous implicit declaration of 'ERR_PTR' was here
return ERR_PTR(-EOPNOTSUPP);
^
...
Fixes: 0fc174dea545 ("ebpf: make internal bpf API independent of CONFIG_BPF_SYSCALL ifdefs")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lawrence Brakmo says:
====================
tcp: add NV congestion control
Removed most of the module parameters
Tested in a rack using between 1 and 380 active TCP-NV flows.
Consists of the following patches:
[PATCH net-next v2 1/2] tcp: add in_flight to tcp_skb_cb
[PATCH net-next v2 2/2] tcp: add NV congestion control
====================
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
|
|
TCP-NV (New Vegas) is a major update to TCP-Vegas.
An earlier version of NV was presented at 2010's LPC.
It is a delayed based congestion avoidance for the
data center. This version has been tested within a
10G rack where the HW RTTs are 20-50us and with
1 to 400 flows.
A description of TCP-NV, including implementation
details as well as experimental results, can be found at:
http://www.brakmo.org/networking/tcp-nv/TCPNV.html
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add in_flight (bytes in flight when packet was sent) field
to tx component of tcp_skb_cb and make it available to
congestion modules' pkts_acked() function through the
ack_sample function argument.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mike Rapoport says:
====================
virtio_net: use common code for virtio_net_hdr and skb GSO conversion
This patches introduce virtio_net_hdr_{from,to}_skb functions for
conversion of GSO information between skb and virtio_net_hdr.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace open coded conversion between virtio_net_hdr to skb GSO info with
virtio_net_hdr_from_skb
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace open coded conversion between virtio_net_hdr to skb GSO info with
virtio_net_hdr_{from,to}_skb
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace open coded conversion between virtio_net_hdr to skb GSO info with
virtio_net_hdr_{from,to}_skb
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace open coded conversion between virtio_net_hdr to skb GSO info with
virtio_net_hdr_{from,to}_skb
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code for conversion between virtio_net_hdr and skb GSO info is
duplicated at several places. Let's put it to a common place to allow
reuse.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This gives better namespacing and prevents conflicts with no-uapi version
of virtio_net header that will be introduced in the following patch.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc_workqueue replaces deprecated create_workqueue().
Since the driver is infiniband which can be used as block device and the
workqueue seems involved in regular operation of the device, so a
dedicated workqueue has been used with WQ_MEM_RECLAIM set to guarantee
forward progress under memory pressure.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
