summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-09-07drm: Do not force 1024x768 modes on unknown connectorsChris Wilson
Only fallback to a set of default modes on a connector iff that connector is known to be connected. The issue occurs that with limited hardware which cannot probe a connector and so reports the connector status as unknown will then attempt to retrieve the modes for it during drm_helper_probe_single_connector_modes(). Should that fail, the helper then generates a default set which fools the fb_helper and causes havoc with the console and beyond. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-09-07drm/kms: Add a module parameter to disable pollingChris Wilson
Polling for a VGA device on an old system can be quite expensive, causing latencies on the order of 600ms. As we hold the mode mutex for this time and also need the same mutex to move the cursor, we trigger a user-visible stall. The real solution would involve improving the granulatity of the locking and so perhaps performing some of the probing not under the lock or some other updates can be done under different locks. Also reducing the cost of probing for a non-existent monitor would be worthwhile. However, exposing a parameter to disable polling is a simple workaround in the meantime. In order to accommodate users turning polling on and off at runtime, the polling is potentially re-enabled on every probe. This is coupled to the user calling xrandr, which seems to be a vaild time to reset the polling timeout since the information on the connection has just been updated. (The presumption being that all connections are probed in a single xrandr pass, which is currently valid.) References: Bug 29536 - 2.6.35 causes ~600ms latency every 10s https://bugs.freedesktop.org/show_bug.cgi?id=29536 Bug 16265 - Why is kslowd accumulating so much CPU time? https://bugzilla.kernel.org/show_bug.cgi?id=16265 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-09-07drm/radeon/kms: fix tv-out on avivo asicsAlex Deucher
digital underscan support regressed tv-out. fixes: https://bugs.freedesktop.org/show_bug.cgi?id=29985 Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-09-07drm/radeon/kms/evergreen: fix gpu hangs in userspace accel codeAlex Deucher
These VGT regs need to be programmed via the ring rather than MMIO as on previous asics (r6xx/r7xx). Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-09-03Staging: wlan-ng: Explicitly set some fields in cfg80211 interfaceKarl Relton
The cfg80211 api has introduced a few new fields. Rather than assume what cfg80211 api does by default, set these explicitly. Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03Staging: octeon: depends on NETDEVICESRandy Dunlap
OCTEON_ETHERNET should depend on NETDEVICES. Fixes this kconfig warning: warning: (NET_DSA && NET && EXPERIMENTAL && NETDEVICES && !S390 || ... || OCTEON_ETHERNET && STAGING && !STAGING_EXCLUDE_BUILD && CPU_CAVIUM_OCTEON) selects PHYLIB which has unmet direct dependencies (!S390 && NETDEVICES) Reported-by: Arnaud Lacombe <lacombar@gmail.com> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: support@caviumnetworks.com Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03Staging: spectra: depend on X86_MRSTJeff Mahoney
lld_nand fails to build on arches without virt_to_bus. Since this driver is specifically for hardware enablment on Moorestown, this patch adds Moorestown MID support as a dependency. Signed-off-by: Jeff Mahoney <jeffm@suse.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03Staging: zram: free device memory when init failsShahar Havivi
Signed-off-by: Shahar Havivi <shaharh@redhat.com> Cc: Nitin Gupta <ngupta@vflare.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03Staging: rt2870sta: Add more device IDs from vendor driversBen Hutchings
Taken from DPO_RT3070_LinuxSTA_V2.3.0.4_20100604.tar.bz2 and 2010_0709_RT2870_Linux_STA_v2.4.0.1.tar.bz2, with duplicates removed. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03staging: comedi das08_cs.c: Fix io_req_t conversionAndreas Bombe
Commit 90abdc3b9 converted all PCMCIA users away from io_req_t. In das08_cs.c the converted IO lines mask setting was added but the old line using the now inexistent p_dev->io was not removed. Signed-off-by: Andreas Bombe <aeb@debian.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03staging: spectra needs <linux/slab.h>Geert Uytterhoeven
On one of my m68k test builds I get: drivers/staging/spectra/ffsport.c: In function ‘ioctl_read_page_data’: drivers/staging/spectra/ffsport.c:196: error: implicit declaration of function ‘kmalloc’ drivers/staging/spectra/ffsport.c:196: warning: assignment makes pointer from integer without a cast drivers/staging/spectra/ffsport.c:212: error: implicit declaration of function ‘kfree’ drivers/staging/spectra/ffsport.c: In function ‘ioctl_write_page_data’: drivers/staging/spectra/ffsport.c:229: warning: assignment makes pointer from integer without a cast drivers/staging/spectra/ffsport.c: In function ‘SBD_setup_device’: drivers/staging/spectra/ffsport.c:637: warning: assignment makes pointer from integer without a cast Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03staging: hv: Fixed lockup problem with bounce_buffer scatter listHank Janssen
Fixed lockup problem with bounce_buffer scatter list which caused crashes in heavy loads. And minor code indentation cleanup in effected area. Removed whitespace and noted minor indentation changes in description as pointed out by Joe Perches. (Thanks for reviewing Joe) Signed-off-by: Hank Janssen <hjanssen@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03staging: hv: Increased storvsc ringbuffer and max_io_requestsHank Janssen
Increased storvsc ringbuffer and max_io_requests. This now more closely mimics the numbers on Hyper-V. And will allow more IO requests to take place for the SCSI driver. Max_IO is set to double from what it was before, Hyper-V allows it and we have had appliance builder requests to see if it was a problem to increase the number. Ringbuffer size for storvsc is now increased because I have seen A few buffer problems on extremely busy systems. They were Set pretty low before. And since max_io_requests is increased I Really needed to increase the buffer as well. Signed-off-by:Hank Janssen <hjanssen@microsoft.com> Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03staging: hv: Fixed the value of the 64bit-hole inside ring bufferHaiyang Zhang
Fixed the value of the 64bit-hole inside ring buffer, this caused a problem on Hyper-V when running checked Windows builds. Checked builds of Windows are used internally and given to external system integrators at times. They are builds that for example that all elements in a structure follow the definition of that Structure. The bug this fixed was for a field that we did not fill in at all (Because we do Not use it on the Linux side), and the checked build of windows gives errors on it internally to the Windows logs. This fixes that error. Signed-off-by:Hank Janssen <hjanssen@microsoft.com> Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03staging: hv: Fixed bounce kmap problem by using correct indexHank Janssen
Fixed bounce offset kmap problem by using correct index. The symptom of the problem is that in some NAS appliances this problem represents Itself by a unresponsive VM under a load with many clients writing small files. Signed-off-by:Hank Janssen <hjanssen@microsoft.com> Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03staging: hv: Fix missing functions for net_device_opsHaiyang Zhang
Fix missing functions for net_device_ops. It's a bug when porting the drivers from 2.6.27 to 2.6.32. In 2.6.27, the default functions for Ethernet, like eth_change_mtu(), were assigned by ether_setup(). But in 2.6.32, these function pointers moved to net_device_ops structure and no longer be assigned in ether_setup(). So we need to set these functions in our driver code. It will ensure the MTU won't be set beyond 1500. Otherwise, this can cause an error on the server side, because the HyperV linux driver doesn't support jumbo frame yet. Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Hank Janssen <hjanssen@microsoft.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: ftdi_sio: Added custom PIDs for ChamSys productsLuke Lowrey
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products Signed-off-by: Luke Lowrey <luke@chamsys.co.uk> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: cdc-acm: Fixing crash when ACM probing interfaces with no endpoint ↵Toby Gray
descriptors. Certain USB devices, such as the Nokia X6 mobile phone, don't expose any endpoint descriptors on some of their interfaces. If the ACM driver is forced to probe all interfaces on a device the a NULL pointer dereference will occur when the ACM driver attempts to use the endpoint of the alternative settings. One way to get the ACM driver to probe all the interfaces is by using the /sys/bus/usb/drivers/cdc_acm/new_id interface. This patch checks that the endpoint pointer for the current alternate settings is non-NULL before using it. Signed-off-by: Toby Gray <toby.gray@realvnc.com> Cc: Oliver Neukum <oliver@neukum.name> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: cdc-acm: Add pseudo modem without AT command capabilitiesPhilippe Corbes
cdc-acm.c : Manage pseudo-modem without AT commands capabilities Enable to drive electronic simple gadgets based on microcontrolers. The Interface descriptor is like this: bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 0 None Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: cxacru: Use a bulk/int URB to access the command endpointSimon Arlott
The command endpoint is either a bulk or interrupt endpoint, but using the wrong type of transfer causes an error if CONFIG_USB_DEBUG is enabled after commit f661c6f8c67bd55e93348f160d590ff9edf08904, which checks for this mismatch. Detect which type of endpoint it is and use a bulk/int URB as appropriate. There are other function calls specifying a bulk pipe, but usb_clear_halt doesn't use the pipe type (only the endpoint) and usb_bulk_msg auto-detects interrupt transfers. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: stable <stable@kernel.org> [.34 and newer] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03usb: serial: mos7840: Add USB IDs to support more B&B USB/RS485 converters.Dave Ludlow
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and USO9ML2-4P. This patch expands and corrects a typo in the patch sent on 08-31-2010. Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: cdc-acm: Adding second ACM channel support for various Nokia and one ↵Toby Gray
Samsung phones S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem with a standard AT-command interface, which is picked up correctly by CDC-ACM. The second ACM port is marked as having a vendor-specific protocol. This means that the ACM driver will not claim the second channel by default. This adds support for the second ACM channel for the following devices: Nokia E63 Nokia E75 Nokia 6760 Slide Nokia E52 Nokia E55 Nokia E72 Nokia X6 Nokia N97 Mini Nokia 5800 Xpressmusic Nokia E90 Samsung GTi8510 (INNOV8) Signed-off-by: Toby Gray <toby.gray@realvnc.com> Cc: Oliver Neukum <oliver@neukum.name> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03usb: serial: mos7840: Add USB ID to support the B&B Electronics USOPTL4-2P.Dave Ludlow
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated, powered, USB to RS485 converter. Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: ssu100: turn off debug flagBill Pemberton
Remove the hard coding of the debug flag to 1. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03usb: allow drivers to use allocated bandwidth until unboundThadeu Lima de Souza Cascardo
When using the remove sysfs file, the device configuration is set to -1 (unconfigured). This eventually unbind drivers with the bandwidth_mutex held. Some drivers may call functions that hold said mutex, like usb_reset_device. This is the case for rtl8187, for example. This will lead to the same process holding the mutex twice, which deadlocks. Besides, according to Alan Stern: "The deadlock problem probably could be handled somehow, but there's a separate issue: Until the usb_disable_device call finishes unbinding the drivers, the drivers are free to continue using their allocated bandwidth. We musn't change the bandwidth allocations until after the unbinding is done. So this patch is indeed necessary." Unbinding the driver before holding the bandwidth_mutex solves the problem. If any operation after that fails, drivers are not bound again. But that would be a problem anyway that the user may solve resetting the device configuration to one that works, just like he would need to do in most other failure cases. Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: cp210x usb driver: add USB_DEVICE for Pirelli DP-L10 mobile.A E Lawrence
The Pirelli DP-L10 mobile is sold under various brand names. One, already supported by cp210x, is the T-COM TC300. Here is the lsusb for that version: ------------------------------------------------------------------- Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0489 Foxconn / Hon Hai idProduct 0xe000 T-Com TC 300 bcdDevice 1.00 iManufacturer 1 Silicon Labs iProduct 2 TC 300 iSerial 3 0001 [snip] --------------------------------------------------------------------------- However the native Pirelli DP-L10 is not supported: ------------------------------------------------------------------ Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0489 Foxconn / Hon Hai idProduct 0xe003 Pirelli DP-L10 bcdDevice 1.00 iManufacturer 1 Silicon Labs iProduct 2 DP-L10 iSerial 3 0001 [snip] ------------------------------------------------------------------------- All that is required is an extra USB_DEVICE entry: { USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM +Mobile */ The patch adds that entry. Tested under 2.6.36-rc2 from git. Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: cp210x: Add B&G H3000 link cable IDJason Detring
This is the cable between an H3000 navigation unit and a multi-function display. http://www.bandg.com/en/Products/H3000/Spares-and-Accessories/Cables/H3000-CPU-USB-Cable-Pack/ Signed-off-by: Jason Detring <jason.detring@navico.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: CP210x Add new device IDCraig Shelley
New device ID added for Balluff RFID reader. Signed-off-by: Craig Shelley <craig@microtron.org.uk> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: option: fix incorrect novatel entriesDirk De Schepper
Unfortunately some of the hardware PID belonging to auto-install CDROM (AICD) of Novatel modems found their way into the option module. This causes the AICD to be treated as a modem in stead of a disk. Since the modem ports do not appear until after the AICD is ejected, this essentially disables the modem. After a couple of minutes the AICD should auto-eject, but it is just too long a wait. The frequency of the failure seems to depend on both the hardware and the linux distribution. Here is a patch that fixes this up, and also adds a couple of new PID, offering some explanations and removing some incomplete and unnecessary comments. Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: Fix kernel oops with g_ether and WindowsMaxim Osipov
Please find attached patch for https://bugzilla.kernel.org/show_bug.cgi?id=16023 problem. Signed-off-by: Maxim Osipov <maxim.osipov@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: rndis: section mismatch fixHenrik Kretzschmar
This patch removes the following section mismatch warning, by moving the function rndis_init() from .init.text to .text. WARNING: vmlinux.o(.text+0x1aeca5a): Section mismatch in reference from the function rndis_bind_config() to the function .init.text:rndis_init() The function rndis_bind_config() references the function __init rndis_init(). This is often because rndis_bind_config lacks a __init annotation or the annotation of rndis_init is wrong. Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: ehci-ppc-of: problems in unwindDan Carpenter
The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do because the ioremap() was the last thing we did. Also if we hit any of the goto statements in the original code then it would have led to a NULL dereference of "ehci". This bug was introduced in: 796bcae7361c "USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]" I modified the few lines in front a little so that my code didn't obscure the return success code path. Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03USB: s3c-hsotg: Remove DEBUG defineMaurus Cuelenaere
DEBUG is defined unconditionally, remove it as this clutters the message log. Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03tty: fix tty_line must not be equal to number of allocated tty pointers in ↵Nathael Pajani
tty driver I found a bug "by chance" in drivers/char/tty_io.c I mean "by chance" because I was just reading the code of the tty_find_polling_driver() to make a new tty_find_by_name() function. In tty_find_polling_driver() the driver actually test "tty_line <= p->num" while num refers to the number of struct tty_struct pointers allocated for the p->ttys (p is a tty_driver), and tty_line is scanned in a tty name, which can be for example ttyS2. Then tty_line equals 2. And if p->num is 2, we have only p->ttys[0] and p->ttys[1], but no p->ttys[2]. This is actually unharmful, for tty_find_polling_driver() is used only in drivers/serial/kgdboc.c, and there's a test over there to find a console with a matching index, which will never happen. This is still a bug anyway. Signed-off-by: Nathael Pajani <nathael.pajani@ed3l.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03serial: bfin_sport_uart: restore transmit frame sync fixSonic Zhang
The large cleanup/rewrite of resources in commit ccf68e59e93181df9353c0cc accidentally reverted an earlier fix in commit a19e8b205915b2925aca75b. So restore it here. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: stable <stable@kernel.org> [.34 and newer] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03serial: fix port type conflict between NS16550A & U6_16550APhilippe Langlais
Bug seen by Dr. David Alan Gilbert with sparse Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03MAINTAINERS: orphan isicomJiri Slaby
I do not maintain isicom anymore... Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03vt: Fix console corruption on driver hand-over.Francisco Jerez
After 02f0777a0d6560eb995aade34a1b82f95c0452da "vc_origin" is no longer reset to the screen buffer before calling the con_init() hook of the new console driver. If the old driver wasn't using a fixed scanout buffer (e.g. the case of vgacon) "vc_origin" may be a pointer to a VRAM location, and its contents aren't guaranteed to be preserved after calling con_deinit() on the old driver and con_init() on the new driver, i.e. the subsequent console resize may fill the framebuffer with garbage. It can be reproduced in the transition from vgacon to the nouveau framebuffer driver: in that case the legacy VGA aperture "vc_origin" points to becomes unreadable after fbcon_init(). This patch reverts the mentioned commit. To avoid the problem it intended to fix, stop using "vc_scr_end" in vc_do_resize() to calculate how many rows we have to copy (actually the code looks simpler this way without the help of "vc_scr_end"). Signed-off-by: Francisco Jerez <currojerez@riseup.net> Cc: qiaochong <qiaochong@loongson.cn> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03sysfs: checking for NULL instead of ERR_PTRDan Carpenter
d_path() returns an ERR_PTR and it doesn't return NULL. Signed-off-by: Dan Carpenter <error27@gmail.com> Cc: stable <stable@kernel.org> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-03Merge branch '2.6.36-xfs-misc' of ↵Alex Elder
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/xfsdev
2010-09-03xfs: Make fiemap work with sparse filesTao Ma
In xfs_vn_fiemap, we set bvm_count to fi_extent_max + 1 and want to return fi_extent_max extents, but actually it won't work for a sparse file. The reason is that in xfs_getbmap we will calculate holes and set it in 'out', while out is malloced by bmv_count(fi_extent_max+1) which didn't consider holes. So in the worst case, if 'out' vector looks like [hole, extent, hole, extent, hole, ... hole, extent, hole], we will only return half of fi_extent_max extents. This patch add a new parameter BMV_IF_NO_HOLES for bvm_iflags. So with this flags, we don't use our 'out' in xfs_getbmap for a hole. The solution is a bit ugly by just don't increasing index of 'out' vector. I felt that it is not easy to skip it at the very beginning since we have the complicated check and some function like xfs_getbmapx_fix_eof_hole to adjust 'out'. Cc: Dave Chinner <david@fromorbit.com> Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Alex Elder <aelder@sgi.com>
2010-09-03Merge remote branch 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next into ↵Dave Airlie
drm-fixes * 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: drm/nv50: initialize ramht_refs list for faked 0 channel drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL. drm/nouveau: Take fence spinlock before reading the last sequence.
2010-09-03xfs: prevent 32bit overflow in space reservationDave Chinner
If we attempt to preallocate more than 2^32 blocks of space in a single syscall, the transaction block reservation will overflow leading to a hangs in the superblock block accounting code. This is trivially reproduced with xfs_io. Fix the problem by capping the allocation reservation to the maximum number of blocks a single xfs_bmapi() call can allocate (2^21 blocks). Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
2010-09-03drm/nv50: initialize ramht_refs list for faked 0 channelMarcin Slusarz
We need it for PFIFO_INTR_CACHE_ERROR interrupt handling, because nouveau_fifo_swmthd looks for matching gpuobj in ramht_refs list. It fixes kernel panic in nouveau_gpuobj_ref_find. Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-09-03drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.Francisco Jerez
We don't need it and it can lead to lock order inversions with respect to drm_global_mutex, potentially causing dead locks. Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-09-03drm/nouveau: Take fence spinlock before reading the last sequence.Francisco Jerez
It fixes a race between the TTM delayed work queue and the GEM IOCTLs (fdo bug 29583) uncovered by the BKL removal. Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-09-02pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimatorJarek Poplawski
This patch fixes a lockdep warning: [ 516.287584] ========================================================= [ 516.288386] [ INFO: possible irq lock inversion dependency detected ] [ 516.288386] 2.6.35b #7 [ 516.288386] --------------------------------------------------------- [ 516.288386] swapper/0 just changed the state of lock: [ 516.288386] (&qdisc_tx_lock){+.-...}, at: [<c12eacda>] est_timer+0x62/0x1b4 [ 516.288386] but this lock took another, SOFTIRQ-unsafe lock in the past: [ 516.288386] (est_tree_lock){+.+...} [ 516.288386] [ 516.288386] and interrupts could create inverse lock ordering between them. ... So, est_tree_lock needs BH protection because it's taken by qdisc_tx_lock, which is used both in BH and process contexts. (Full warning with this patch at netdev, 02 Sep 2010.) Fixes commit: ae638c47dc040b8def16d05dc6acdd527628f231 ("pkt_sched: gen_estimator: add a new lock") Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02ipvs: avoid oops for passive FTPJulian Anastasov
Fix Passive FTP problem in ip_vs_ftp: - Do not oops in nf_nat_set_seq_adjust (adjust_tcp_sequence) when iptable_nat module is not loaded Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02Revert "sky2: don't do GRO on second port"David S. Miller
This reverts commit de6be6c1f77798c4da38301693d33aff1cd76e84. After some discussion with Jarek Poplawski and Eric Dumazet, we've decided that this change is incorrect. Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02xfs: Disallow 32bit project quota idArkadiusz Mi?kiewicz
Currently on-disk structure is able to keep only 16bit project quota id, so disallow 32bit ones. This fixes a problem where parts of kernel structures holding project quota id are 32bit while parts (on-disk) are 16bit variables which causes project quota member files to be inaccessible for some operations (like mv/rm). Signed-off-by: Arkadiusz Mi?kiewicz <arekm@maven.pl> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 21:49:51 +0000