| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.12-rc2
Here's a fix for a long-standing issue in the ftdi_sio driver that
prevented unprivileged users from updating the low-latency flag,
something which became apparent after a recent change that restored the
older setting of not using low-latency mode by default.
A run of sparse revealed a couple of endianness issues that are now
fixed, and addressed is also a user-triggerable division-by-zero in
io_ti when debugging is enabled.
Finally there are some new device ids, including a simplification of how
we deal with a couple of older Olimex JTAG adapters.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.12-rc cycle most consisting of few minor dts fixes
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
* tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.12:
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
* tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable Qualcomm drivers needed to boot Dragonboard 410c with HDMI. This
enables support for clocks, regulators, and USB PHY.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
[Olof: Turned off _RPM configs per follow-up email]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Sync the defconfig with savedefconfig as config options change/move over
time.
Generated with the following commands:
make defconfig
make savedefconfig
cp defconfig arch/arm64/configs/defconfig
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
It makes sense to have a stripped-down defconfig for just Gemini, as
it is a pretty small platform used in NAS etc, and will use appended
device tree. It is also quick to compile and test. Hopefully this
defconfig can be a good base for distributions such as OpenWRT.
I plan to add in the config options needed for the different
variants of Gemini as we go along.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom SoC drivers fixes for 4.12, please
pull the following:
- Florian removes the duplicate compatible string matched by the
SUN_TOP_CTRL driver and instead uses the correct one for 7435
* tag 'arm-soc/for-4.12/drivers-fixes' of http://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Correctly match 7435 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
* tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835: add index to the ethernet alias
ARM: dts: bcm2835: fix uart0/uart1 pins
ARM: dts: bcm2835: fix i2c0 pins
ARM: dts: bcm2835: fix uart0 pinctrl node names
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6e3 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
xen_flush_tlb_all() is used in arch/x86/xen/mmu.c only. Make it static.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
There are some leftovers testing for pvh guest mode in pv-only source
files. Remove them.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
As stack tracing now requires "rcu watching", force RCU to be watching when
recording a stack trace.
Link: http://lkml.kernel.org/r/20170512172449.879684501@goodmis.org
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
virt_addr_valid() is supposed to tell you if it's OK to call virt_to_page() on
an address. What this means in practice is that it should only return true for
addresses in the linear mapping which are backed by a valid PFN.
We are failing to properly check that the address is in the linear mapping,
because virt_to_pfn() will return a valid looking PFN for more or less any
address. That bug is actually caused by __pa(), used in virt_to_pfn().
eg: __pa(0xc000000000010000) = 0x10000 # Good
__pa(0xd000000000010000) = 0x10000 # Bad!
__pa(0x0000000000010000) = 0x10000 # Bad!
This started happening after commit bdbc29c19b26 ("powerpc: Work around gcc
miscompilation of __pa() on 64-bit") (Aug 2013), where we changed the definition
of __pa() to work around a GCC bug. Prior to that we subtracted PAGE_OFFSET from
the value passed to __pa(), meaning __pa() of a 0xd or 0x0 address would give
you something bogus back.
Until we can verify if that GCC bug is no longer an issue, or come up with
another solution, this commit does the minimal fix to make virt_addr_valid()
work, by explicitly checking that the address is in the linear mapping region.
Fixes: bdbc29c19b26 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Breno Leitao <breno.leitao@gmail.com>
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.12-rc2
* tag 'drm-intel-fixes-2017-05-18-1' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: don't do allocate_va_range again on PIN_UPDATE
drm/i915: Fix rawclk readout for g4x
drm/i915: Fix runtime PM for LPE audio
drm/i915/glk: Fix DSI "*ERROR* ULPS is still active" messages
drm/i915/gvt: avoid unnecessary vgpu switch
drm/i915/gvt: not to restore in-context mmio
drm/i915/gvt: fix typo: "supporte" -> "support"
|
|
misc nouveau fixes.
* 'linux-4.12' of git://github.com/skeggsb/linux:
drm/nouveau/fifo/gk104-: Silence a locking warning
drm/nouveau/secboot: plug memory leak in ls_ucode_img_load_gr() error path
drm/nouveau: Fix drm poll_helper handling
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Driver Changes:
- host1x: Fix link error when host1x is built-in and iova is a module (Arnd)
- hlcdc: Fix arguments passed to drm_of_find_panel_or_bridge (Boris)
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
* tag 'drm-misc-fixes-2017-05-18' of git://anongit.freedesktop.org/git/drm-misc:
drm/atmel-hlcdc: Fix output initialization
gpu: host1x: select IOMMU_IOVA
|
|
into drm-fixes
one etnaviv fence leak fix.
* 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux:
drm/etnaviv: don't put fence in case of submit failure
|
|
Pull MD fixes from Shaohua Li:
- Several bug fixes for raid5-cache from Song Liu, mainly handle
journal disk error
- Fix bad block handling in choosing raid1 disk from Tomasz Majchrzak
- Simplify external metadata array sysfs handling from Artur
Paszkiewicz
- Optimize raid0 discard handling from me, now raid0 will dispatch
large discard IO directly to underlayer disks.
* tag 'md/4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid1: prefer disk without bad blocks
md/r5cache: handle sync with data in write back cache
md/r5cache: gracefully handle journal device errors for writeback mode
md/raid1/10: avoid unnecessary locking
md/raid5-cache: in r5l_do_submit_io(), submit io->split_bio first
md/md0: optimize raid0 discard handling
md: don't return -EAGAIN in md_allow_write for external metadata arrays
md/raid5: make use of spin_lock_irq over local_irq_disable + spin_lock
|
|
Fixes the following sparse warnings:
net/9p/trans_xen.c:528:5: warning:
symbol 'p9_trans_xen_init' was not declared. Should it be static?
net/9p/trans_xen.c:540:6: warning:
symbol 'p9_trans_xen_exit' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
|
|
In case of error, the function xenbus_read() returns ERR_PTR() and never
returns NULL. The NULL test in the return value check should be replaced
with IS_ERR().
Fixes: 71ebd71921e4 ("xen/9pfs: connect to the backend")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
|
|
Pull networking fixes from David Miller:
1) Don't allow negative TCP reordering values, from Soheil Hassas
Yeganeh.
2) Don't overflow while parsing ipv6 header options, from Craig Gallek.
3) Handle more cleanly the case where an individual route entry during
a dump will not fit into the allocated netlink SKB, from David
Ahern.
4) Add missing CONFIG_INET dependency for mlx5e, from Arnd Bergmann.
5) Allow neighbour updates to converge more quickly via gratuitous
ARPs, from Ihar Hrachyshka.
6) Fix compile error from CONFIG_INET is disabled, from Eric Dumazet.
7) Fix use after free in x25 protocol init, from Lin Zhang.
8) Valid VLAN pvid ranges passed into br_validate(), from Tobias
Jungel.
9) NULL out address lists in child sockets in SCTP, this is similar to
the fix we made for inet connection sockets last week. From Eric
Dumazet.
10) Fix NULL deref in mlxsw driver, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
mlxsw: spectrum: Avoid possible NULL pointer dereference
sh_eth: Do not print an error message for probe deferral
sh_eth: Use platform device for printing before register_netdev()
mlxsw: spectrum_router: Fix rif counter freeing routine
mlxsw: spectrum_dpipe: Fix incorrect entry index
cxgb4: update latest firmware version supported
qmi_wwan: add another Lenovo EM74xx device ID
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
udp: make *udp*_queue_rcv_skb() functions static
bridge: netlink: check vlan_default_pvid range
net: ethernet: faraday: To support device tree usage.
net: x25: fix one potential use-after-free issue
bpf: adjust verifier heuristics
ipv6: Check ip6_find_1stfragopt() return value properly.
selftests/bpf: fix broken build due to types.h
bnxt_en: Check status of firmware DCBX agent before setting DCB_CAP_DCBX_HOST.
bnxt_en: Call bnxt_dcb_init() after getting firmware DCBX configuration.
net: fix compile error in skb_orphan_partial()
ipv6: Prevent overrun when parsing v6 header options
neighbour: update neigh timestamps iff update is effective
...
|
|
Pull sparc fixes from David Miller:
"Three sparc bug fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc/ftrace: Fix ftrace graph time measurement
sparc: Fix -Wstringop-overflow warning
sparc64: Fix mapping of 64k pages with MAP_FIXED
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fix from Masahiro Yamada:
"Fix headers_install to not delete pre-existing headers in the install
destination"
* tag 'kbuild-fixes-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: skip install/check of headers right under uapi directories
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull pid namespace fixes from Eric Biederman:
"These are two bugs that turn out to have simple fixes that were
reported during the merge window. Both of these issues have existed
for a while and it just happens that they both were reported at almost
the same time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
pid_ns: Fix race between setns'ed fork() and zap_pid_ns_processes()
pid_ns: Sleep in TASK_INTERRUPTIBLE in zap_pid_ns_processes
|
|
To fix following build error when SOFTWARE_REBOOT is defined:
CC [M] driver/watchdog/wdt_pci.o
driver/watchdog/wdt_pci.c: In function 'wdtpci_interrupt':
driver/watchdog/wdt_pci.c:335:3: error: too many arguments to function 'emergency_restart'
emergency_restart(NULL);
^
In file included from driver/watchdog/wdt_pci.c:51:0:
include/linux/reboot.h:80:13: note: declared here
extern void emergency_restart(void);
^
Signed-off-by: Shile Zhang <shile.zhang@nokia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
wdt_timeout must not be initialized to CDNS_WDT_DEFAULT_TIMEOUT in
order to allow the value to be overriddden by a device tree setting.
This way, the default timeout value will be used only in case module_param
has not been set, or device tree timeout-sec has not been defined.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
WDT_MR and WDT_CR must not updated within three slow clock periods after
the last ping (write to WDT_CR or WDT_MR). Ensure enough time has elapsed
before writing those registers.
wdt_write() waits for 4 periods to ensure at least 3 edges are seen by the
IP.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou.Yang <wenyou.yang@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The datasheet states: "When setting the WDDIS bit, and while it is set, the
fields WDV and WDD must not be modified."
Because the whole configuration is already cached inside .mr, wait for the
user to enable the watchdog to configure it so it is enabled and configured
at the same time (what the IP is actually expecting).
When the watchdog is already enabled, it is not an issue to reconfigure it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou.Yang <wenyou.yang@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
I ran into one corner case with the orion watchdog using the
atomic_io_modify interface:
drivers/watchdog/orion_wdt.o: In function `orion_stop':
orion_wdt.c:(.text.orion_stop+0x28): undefined reference to `atomic_io_modify'
drivers/watchdog/orion_wdt.o: In function `armada375_stop':
orion_wdt.c:(.text.armada375_stop+0x28): undefined reference to `atomic_io_modify'
This function is available on all 32-bit ARM builds except for ebsa110, so
we have to specifically exclude that from compile-testing.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix problem with hotplug state machine in coretemp driver"
* tag 'hwmon-for-linus-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Handle frozen hotplug state correctly
|
|
In case we got an FDB notification for a port that doesn't exist we
execute an FDB entry delete to prevent it from re-appearing the next
time we poll for notifications.
If the operation failed we would trigger a NULL pointer dereference as
'mlxsw_sp_port' is NULL.
Fix it by reporting the error using the underlying bus device instead.
Fixes: 12f1501e7511 ("mlxsw: spectrum: remove FDB entry in case we get unknown object notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth ee700000.ethernet: failed to initialise MDIO
Fixes: daacf03f0bbfefee ("sh_eth: Register MDIO bus before registering the network device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of fixes from Arkadi
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During rif counter freeing the counter index can be invalid. Add check
of validity before freeing the counter.
Fixes: e0c0afd8aa4e ("mlxsw: spectrum: Support for counters on router interfaces")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of disabled counters the entry index will be incorrect. Fix this
by moving the entry index set before the counter status check.
Fixes: 2ba5999f009d ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes several issues:
- if the 1st 'kzalloc' fails, we dereference a NULL pointer
- if the 2nd 'kzalloc' fails, there is a memory leak
- if 'sysfs_create_bin_file' fails there is also a memory leak
Fix it by adding a test after the first memory allocation and some error
handling paths to correctly free memory if needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drm_of_find_panel_or_bridge() is expecting np to point to the encoder
node, not the bridge or panel this encoder is feeding.
Moreover, the endpoint parameter passed to drm_of_find_panel_or_bridge()
is always set to zero, which prevents us from probing all outputs.
We also move the atmel_hlcdc_rgb_output allocation after the
panel/bridge detection to avoid useless allocations.
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: ebc944613567 ("drm: convert drivers to use drm_of_find_panel_or_bridge")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1495110921-4032-1-git-send-email-boris.brezillon@free-electrons.com
|
|
/dev/mem currently allows mmap() mappings that wrap around the end of
the physical address space, which should probably be illegal. It
circumvents the existing STRICT_DEVMEM permission check because the loop
immediately terminates (as the start address is already higher than the
end address). On the x86_64 architecture it will then cause a panic
(from the BUG(start >= end) in arch/x86/mm/pat.c:reserve_memtype()).
This patch adds an explicit check to make sure offset + size will not
wrap around in the physical address type.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When IOMMU_IOVA is not built-in but host1x is, we get a link error:
drivers/gpu/host1x/dev.o: In function `host1x_remove':
dev.c:(.text.host1x_remove+0x50): undefined reference to `put_iova_domain'
drivers/gpu/host1x/dev.o: In function `host1x_probe':
dev.c:(.text.host1x_probe+0x31c): undefined reference to `init_iova_domain'
dev.c:(.text.host1x_probe+0x38c): undefined reference to `put_iova_domain'
drivers/gpu/host1x/cdma.o: In function `host1x_cdma_init':
cdma.c:(.text.host1x_cdma_init+0x238): undefined reference to `alloc_iova'
cdma.c:(.text.host1x_cdma_init+0x2c0): undefined reference to `__free_iova'
drivers/gpu/host1x/cdma.o: In function `host1x_cdma_deinit':
cdma.c:(.text.host1x_cdma_deinit+0xb0): undefined reference to `free_iova'
This adds the same select statement that we have for drm_tegra.
Fixes: 404bfb78daf3 ("gpu: host1x: Add IOMMU support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170419182449.885312-1-arnd@arndb.de
|
|
Change t4fw_version.h to update latest firmware version
number to 1.16.43.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP needs fixes similar to 83eaddab4378 ("ipv6/dccp: do not inherit
ipv6_mc_list from parent"), otherwise bad things can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the udp memory accounting refactor, we don't need any more
to export the *udp*_queue_rcv_skb(). Make them static and fix
a couple of sparse warnings:
net/ipv4/udp.c:1615:5: warning: symbol 'udp_queue_rcv_skb' was not
declared. Should it be static?
net/ipv6/udp.c:572:5: warning: symbol 'udpv6_queue_rcv_skb' was not
declared. Should it be static?
Fixes: 850cbaddb52d ("udp: use it's own memory accounting schema")
Fixes: c915fe13cbaa ("udplite: fix NULL pointer dereference")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently it is allowed to set the default pvid of a bridge to a value
above VLAN_VID_MASK (0xfff). This patch adds a check to br_validate and
returns -EINVAL in case the pvid is out of bounds.
Reproduce by calling:
[root@test ~]# ip l a type bridge
[root@test ~]# ip l a type dummy
[root@test ~]# ip l s bridge0 type bridge vlan_filtering 1
[root@test ~]# ip l s bridge0 type bridge vlan_default_pvid 9999
[root@test ~]# ip l s dummy0 master bridge0
[root@test ~]# bridge vlan
port vlan ids
bridge0 9999 PVID Egress Untagged
dummy0 9999 PVID Egress Untagged
Fixes: 0f963b7592ef ("bridge: netlink: add support for default_pvid")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Tobias Jungel <tobias.jungel@bisdn.de>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To support device tree usage for ftmac100.
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function x25_init is not properly unregister related resources
on error handler.It is will result in kernel oops if x25_init init
failed, so add properly unregister call on error handler.
Also, i adjust the coding style and make x25_register_sysctl properly
return failure.
Signed-off-by: linzhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The greybus-dev mailing list is a members-only list and is
moderated for non-subscribers.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
