summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-10-28regulator: Add option for machine drivers to enable the dummy regulatorMark Brown
Allow machine drivers to explicitly enable the use of the dummy regulator, enabling simpler support for systems with only a few specific supplies visible to software. It is strongly recommended that this is not used on systems with substantial software control over their PMICs, for maximum functionality constrints should be as fully specified as possible. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28Regulator: lp3972 cleanupAxel Lin
This patch includes below fixes based on Mark's comment. - Return actual error if i2c_smbus_read_byte_data() fail - Add spaces around bitwise AND operator(&) to improve readability - Add comment to explain why we need to update voltage change control register for LDO1 and LDO5 - Logging the value for diagnostics if chip reported incorrect voltage value - Add __devinit annotation for setup_regulators() - Show system control register1 value if the value is mismatched - Logging the value for diagnostics if failed to detect device Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28Regulator: LP3972 PMIC regulator driverAxel Lin
This patch adds regulator drivers for National Semiconductors LP3972 PMIC. This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3972 PMIC controller uses I2C interface. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28MAX8952 PMIC Driver Initial ReleaseMyungJoo Ham
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV with DVS support. In this initial release, users can set voltages for four DVS modes, RAMP delay values, and SYNC frequency. Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID is not supported in this release. If GPIO of EN is not valid in platform data, the driver assumes that it is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down VID0 and VID1 to fix DVS mode as 0 and disables DVS support. We assume that V_OUT is capable to provide every voltage from 770mV to 1.40V in 10mV steps although the data sheet has some ambiguity on it. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> -- v2: - Style correction - Can accept platform_data with invalid GPIOs - Removed unnecessary features - Improved error handling Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28Merge branch 'x86-platform-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86: Move olpc to platform x86: Move uv to platform x86: Move mrst to platform x86: Move scx200 to platform x86: Move visws to platform x86: Move efi to platform x86: Move sfi to platform x86: Add platform directory
2010-10-28Merge branch 'hwmon-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging * 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (68 commits) hwmon: (it87) Add support for the IT8721F/IT8758E hwmon: (it87) Move conversion functions hwmon: Remove many EXPERIMENTAL flags hwmon: (lm85) Add support for ADT7468 high-frequency PWM mode hwmon: (lm85) Document the ADT7468 as supported hwmon: (lm85) Fix ADT7468 frequency table hwmon: I2C addresses are constant Move ams driver to macintosh hwmon: (pcf8591) Don't attempt to detect devices hwmon: (pcf8591) Register as a hwmon device hwmon: (w83795) Use standard attributes for chassis intrusion hwmon: (w83795) Exclude fan control feature by default hwmon: (w83795) Add myself as co-author and maintainer hwmon: (w83795) More style cleanups hwmon: (w83795) Fix LSB reading of voltage limits hwmon: (w83795) Use dev_get_drvdata() where possible hwmon: (w83795) Delay reading pwm config registers hwmon: (w83795) Delay reading limit registers hwmon: (w83795) Move register reads to dedicated functions hwmon: (w83795) Pack similar register reads ...
2010-10-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (841 commits) Staging: brcm80211: fix usage of roundup in structures Staging: bcm: fix up network device reference counting Staging: keucr: fix up US_ macro change staging: brcm80211: brcmfmac: Removed codeversion from firmware filenames. staging: brcm80211: Remove unnecessary header files. staging: brcm80211: Remove unnecessary includes from bcmutils.c staging: brcm80211: Removed unnecessary pktsetprio() function. Staging: brcm80211: remove typedefs.h Staging: brcm80211: remove uintptr typedef usage Staging: hv: remove struct vmbus_channel_interface Staging: hv: remove Open from struct vmbus_channel_interface Staging: hv: storvsc: call vmbus_open directly Staging: hv: netvsc: call vmbus_open directly Staging: hv: channel: export vmbus_open to modules Staging: hv: remove Close from struct vmbus_channel_interface Staging: hv: netvsc: call vmbus_close directly Staging: hv: storvsc: call vmbus_close directly Staging: hv: channel: export vmbus_close to modules Staging: hv: remove SendPacket from struct vmbus_channel_interface Staging: hv: storvsc: call vmbus_sendpacket directly ... Fix up conflicts in drivers/staging/cx25821/cx25821-audio-upstream.c drivers/staging/cx25821/cx25821-audio.h due to warring whitespace cleanups (neither of which were all that great)
2010-10-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (32 commits) sh: intc: switch irq_desc iteration to new active IRQ iterator. sh: fix up cpu hotplug IRQ migration for irq_data changes. sh: oprofile: Make sure the backtrace op is available for timer-fallback. sh64: oprofile: Fix up kernel stack pointer size mismatch. sh: oprofile: Fix up and extend op_name_from_perf_id(). sh: lockless get_user_pages_fast() sh64: _PAGE_SPECIAL support. sound: sh: ctrl_in/outX to __raw_read/writeX conversion. sh: disable deprecated genirq support. sh: update show_interrupts() for irq_data chip lookup. sh: intc: irq_data conversion. sh64: irq_data conversion. sh64: update for IRQ flag handling naming changes. rtc: rtc-rs5c313: ctrl_in/outX to __raw_read/writeX conversion. sh: mach-se: irq_data conversion. input: hp680_ts_input: ctrl_in/outX to __raw_read/writeX conversion. input: jornada680_kbd: ctrl_in/outX to __raw_read/writeX conversion. sh: hd64461: irq_data conversion. sh: mach-x3proto: irq_data conversion. sh: mach-systemh: irq_data conversion. ...
2010-10-28Merge branch 'linux-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits) x86: allocate space within a region top-down x86: update iomem_resource end based on CPU physical address capabilities x86/PCI: allocate space from the end of a region, not the beginning PCI: allocate bus resources from the top down resources: support allocating space within a region from the top down resources: handle overflow when aligning start of available area resources: ensure callback doesn't allocate outside available space resources: factor out resource_clip() to simplify find_resource() resources: add a default alignf to simplify find_resource() x86/PCI: MMCONFIG: fix region end calculation PCI: Add support for polling PME state on suspended legacy PCI devices PCI: Export some PCI PM functionality PCI: fix message typo PCI: log vendor/device ID always PCI: update Intel chipset names and defines PCI: use new ccflags variable in Makefile PCI: add PCI_MSIX_TABLE/PBA defines PCI: add PCI vendor id for STmicroelectronics x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs PCI: OLPC: Only enable PCI configuration type override on XO-1 ...
2010-10-28hwmon: (it87) Add support for the IT8721F/IT8758EJean Delvare
Add support for the IT8721F/IT8758E. These new chips differ from the older IT87xxF chips in the following ways: * ADC LSB is 12 mV instead of 16 mV. * PWM values are 8-bit instead of 7-bit. There are other minor changes we don't have to care about in the driver. Another change is that we will handle internal voltage scaling in the driver instead of delegating the work to user-space. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (it87) Move conversion functionsJean Delvare
Move conversion functions until after structure defintions. This is needed for future changes which make use of the structures in the conversion funtcions. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: Remove many EXPERIMENTAL flagsJean Delvare
Remove the dependency on EXPERIMENTAL for all drivers which are in the kernel tree for a long time, are known to work properly and for which we have documentation. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Corentin Labbe <corentin.labbe@geomatys.fr> Cc: Riku Voipio <riku.voipio@iki.fi> Cc: Juerg Haefliger <juergh@gmail.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (lm85) Add support for ADT7468 high-frequency PWM modeJean Delvare
The ADT7468 supports a high-frequency PWM output mode where all PWM outputs are driven by a 22.5 kHz clock. Add support for this mode, and document it, as it may surprise the user that setting one PWM output frequency also affects the other PWM outputs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (lm85) Document the ADT7468 as supportedJean Delvare
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (lm85) Fix ADT7468 frequency tableJean Delvare
The ADT7468 uses the same frequency table as the ADT7463. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org Cc: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: I2C addresses are constantJean Delvare
We can mark normal_i2c const. Almost all drivers do that already, so fix the 3 remaining ones before they are used as (bad) examples for new drivers. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: George Joseph <george.joseph@fairview5.com> Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28Move ams driver to macintoshJean Delvare
The ams driver isn't a hardware monitoring driver, so it shouldn't live under driver/hwmon. drivers/macintosh seems much more appropriate, as the driver is only useful on PowerBooks and iBooks. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Stelian Pop <stelian@popies.net> Cc: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca>
2010-10-28hwmon: (pcf8591) Don't attempt to detect devicesJean Delvare
The PCF8591 can't be detected, don't even try. There are plenty of other means to instantiate i2c devices these days. Signed-off-by: Jean Delvare <khali@linux-fr.org> Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Aurelien Jarno <aurelien@aurel32.net>
2010-10-28hwmon: (pcf8591) Register as a hwmon deviceJean Delvare
Register PCF8591 devices as hwmon devices. There's little point in implementing the standard sysfs interface if we don't register it in a way libsensors will pick it. Signed-off-by: Jean Delvare <khali@linux-fr.org> Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Aurelien Jarno <aurelien@aurel32.net>
2010-10-28hwmon: (w83795) Use standard attributes for chassis intrusionJean Delvare
Follow the standard attribute naming for the chassis intrusion feature. I couldn't test the beeping (my board apparently doesn't do that) but the alarm works fine. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Exclude fan control feature by defaultJean Delvare
The fan control feature of the w83795 driver is insufficiently reviewed and tested for public consumption at this time, so make it optional and disabled by default. We will change the default when review and testing is deemed sufficient. Ultimately the option will go away. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Add myself as co-author and maintainerJean Delvare
I've made so many changes to the w83795 driver that it's only fair to list myself as a co-author. I'll also maintain the driver for some time. There's more work needed on the driver for sure. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) More style cleanupsJean Delvare
Cleanups suggested by Guenter Roeck, falling into 4 categories: * Swapping test orders, because if (var == CONSTANT) is much easier to read than if (CONSTANT == var). * Simplifying comparisons with 0. * Dropping unneeded masks. * Dropping unneeded parentheses and curly braces. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Fix LSB reading of voltage limitsJean Delvare
Wrong index caused the wrong register value to be read, resulting in random LSB for voltage limits. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Use dev_get_drvdata() where possibleJean Delvare
When we don't need the client pointer, calling dev_get_drvdata() is more efficient that calling to_i2c_client() and then i2c_get_clientdata(). Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Delay reading pwm config registersJean Delvare
Wait until we need the pwm config register values, instead of pre-reading them. This saves over 1 second on modprobe on my test system. Obviously this time is added when first accessing pwm config attributes, however not everybody will use them, so it seems unfair to slow down driver loading (and thus boot) for an optional feature. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Delay reading limit registersJean Delvare
Wait until we need the limit register values, instead of pre-reading them. This saves 544 ms on modprobe on my test system. Obviously this time is added when first running "sensors" or any other monitoring application, but I think it is better than slowing down the boot. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Move register reads to dedicated functionsJean Delvare
Move initial register reads out of probe, to dedicated functions. This makes the code clearer, and will be needed if we want to delay calling these functions until they are needed, or want to call them periodically. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Pack similar register readsJean Delvare
Pack similar register reads using for loops. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Make W83795_REG_PWM more efficientJean Delvare
Cascaded conditionals are inefficient. Reorder the fields so that PWM register addresses can be computed more efficiently. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Don't pre-read values we'll update laterJean Delvare
There is no point in reading registers during initialization if we will refresh the values in the update function later. This is only slowing down the driver loading with no benefit, stop doing it. This change saves 480 ms on driver load on my test system. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Simplify temperature sensor type handlingJean Delvare
All 3 temperature sensor type sysfs functions (show_temp_mode, store_temp_mode and show_dts_mode) can be simplified. We don't create these files when the correponding input isn't in temperature monitoring mode, so there is no point in handling that case. Likewise, we don't allow changing inputs from temperature to voltage, so the code handling this case is dead and can be removed. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Drop _NUM constantsJean Delvare
Consistently use ARRAY_SIZE() to control for loops. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Drop REST_VLT_BEGIN/ENDJean Delvare
Get rid of REST_VLT_BEGIN and REST_VLT_END, they don't make the code more readable. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Fix parity checksJean Delvare
x % 1 is obviously wrong, as it always evaluates to 0. You want x % 2, or x & 1, for parity checking. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Get rid of VRLSB_SHIFTJean Delvare
VRLSB_SHIFT is a non-sense, the actual shift depends on the sensor type (fans need 4, other sensors need 6). Get rid of it to prevent any confusion. Also get rid of the useless masking, the meaningful bits are always the MSb so there's nothing to mask out after shifting. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Avoid reading the same register twiceJean Delvare
Shorten driver load time by avoiding duplicate register access during initialization. This saves 112 ms on modprobe on my test system. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Rework beep_enable implementationJean Delvare
Handle beep_enable just like all other beep bits. It doesn't need anything special, so let's avoid redundant code. This also saves a duplicate register read at initialization time. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Report PECI agent Tbase valuesJean Delvare
On systems with PECI, report PECI agent Tbase temperature values. This is informative only. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Properly handle negative temperaturesJean Delvare
The temperature registers hold regular 2's complement values, no need to add any arithmetics. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Rename temperature limit attributesJean Delvare
Follow the standard for temperature limit attribute naming, so that libsensors will pick the values. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Fix PWM duty cycle frequency attributesJean Delvare
The PWM duty cycle frequenty attributes are improperly named (fanN_div instead of pwmN_div) and contain raw values instead of actual frequencies. Rename them and fix their contents. Also improve the logic when the user asks for a new frequency, to always pick the closest supported frequency. The algorithm could certainly be optimized, but the operation is infrequent enough that I don't think it's worth the effort. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Add support for dynamic in0-2 limitsJean Delvare
The W83795G can be configured to set the in0, in1 and/or in2 voltage limits dynamically based on VID input pins. Switch the respective sysfs attributes to read-only. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Fix LSB reading of fan speedsJean Delvare
Misplaced parentheses caused the wrong register value to be read, resulting in random LSB for fan speed values and limits. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Clean up probe functionJean Delvare
* The data structure is zalloc'd, so no need to set individual fields to 0 explicitly. * Refactor the handling of pins that can be used for either temperature or voltage monitoring. * Misc other clean-ups. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Fix in17-in20 gain factorJean Delvare
Gain bit set means 1x gain and cleared means 8x gain, not the other way around. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Only start monitoring if neededJean Delvare
This saves an SMBus write if monitoring was already enabled. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Add const markersJean Delvare
Attribute structures can be made const. Same for the I2C address list. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Only create fan[1-8]_target files when neededJean Delvare
Only create fan[1-8]_target files when the fan in question can be controlled (PWM output is present.) Also name these files according to the standard. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Move PWM attributes to a dedidated arrayJean Delvare
Use a dedicated 2D array for PWM attributes. This way, PWM attributes are handled the same way as other attributes, this is more consistent. Signed-off-by: Jean Delvare <khali@linux-fr.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 11:20:37 +0000