Age | Commit message (Collapse) | Author |
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.4, please pull the following:
- Stefan fixes the MMC controller bus-width property for the Raspberry Pi
Zero Wireless which was incorrect after a prior refactoring
* tag 'arm-soc/for-5.4/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
Link: https://lore.kernel.org/r/20191015172356.9650-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
DaVinci fixes for v5.4
======================
* fix GPIO backlight support on DA850 by enabling the needed config
in davinci_all_defconfig. This is a fix because the driver and board
support got converted to use BACKLIGHT_GPIO driver, but defconfig update
is still missing in v5.4.
* fix for McBSP DMA on DM365
* tag 'davinci-fixes-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
Link: https://lore.kernel.org/r/7f3393f9-59be-a2d4-c1e1-ba6e407681d1@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
A number of fixes for individual boards like the rockpro64, and Hugsun X99
as well as a fix for the Gru-Kevin display override and fixing the dt-
binding for Theobroma boards to the correct naming that is also actually
used in the wild.
* tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
arm64: dts: rockchip: Fix usb-c on Hugsun X99 TV Box
arm64: dts: rockchip: fix RockPro64 sdmmc settings
arm64: dts: rockchip: fix RockPro64 sdhci settings
arm64: dts: rockchip: fix RockPro64 vdd-log regulator settings
dt-bindings: arm: rockchip: fix Theobroma-System board bindings
arm64: dts: rockchip: fix Rockpro64 RK808 interrupt line
Link: https://lore.kernel.org/r/1599050.HRXuSXmxRg@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191017141851.GA22506@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
* tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use level interrupt for omap4 & 5 wlcore
ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage
ARM: dts: omap5: fix gpu_cm clock provider name
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
Link: https://lore.kernel.org/r/pull-1571242890-118432@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 5.4, please pull the following:
- Rayangonda fixes the GPIO pins assignment for the Stringray SoCs
* tag 'arm-soc/for-5.4/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: Fix gpio to pinmux mapping
Link: https://lore.kernel.org/r/20191015172356.9650-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
DA850 EVM has been converted to use GPIO backlight device
for display backlight GPIO control.
Enable the GPIO backlight module in davinci_all_defconfig
to keep backlight support working.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: edits to commit message for context]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
dm365 have only single McBSP, so the device name is without .0
Fixes: 0c750e1fe481d ("ARM: davinci: dm365: Add dma_slave_map to edma")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The commit e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at
board level") accidently dropped the bus width for the sdhci on the
RPi Zero W, because the board file was relying on the defaults
from bcm2835-rpi.dtsi. So fix this performance regression by adding
the bus width to the board file.
Fixes: e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at board level")
Reported-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Since commit 2eba69071b4b ("drm/msm: Remove Kconfig default") the
CONFIG_DRM_MSM option is no longer selected by default on i.MX5.
Explicitly select CONFIG_DRM_MSM so that we can get GPU support
by default on i.MX51 and i.MX53.
Fixes: 2eba69071b4b ("drm/msm: Remove Kconfig default")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MN, usdhc's ipg clock is from IMX8MN_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MN_CLK_DUMMY.
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MM, usdhc's ipg clock is from IMX8MM_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MM_CLK_DUMMY.
Fixes: a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MQ, usdhc's ipg clock is from IMX8MQ_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MQ_CLK_DUMMY.
Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd1d ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Specify 'i2c-mux-idle-disconnect' for both I2C switches present on the
board, since both are connected to the same parent bus and all of
their children have the same I2C address.
Fixes: ca4b4d373fcc ("ARM: dts: vf610: Add ZII SCU4 AIB board")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Jeff White <jeff.white@zii.aero>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A previous patch disabled the SNVS power key by default which
breaks the ability for the imx6q-logicpd board to wake from sleep.
This patch re-enables this feature for this board.
Fixes: 770856f0da5d ("ARM: dts: imx6qdl: Enable SNVS power key according to board design")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
lx2160a support PW15 but not PW20, correct name to avoid confusing.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Fixes: 00c5ce8ac023 ("arm64: dts: lx2160a: add cpu idle support")
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
arm/fixes
mvebu fixes for 5.4 (part 1)
Fix regression on USB for Turris Mox (Armada 3720 based board)
* tag 'mvebu-fixes-5.4-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: armada-3720-turris-mox: convert usb-phy to phy-supply
Link: https://lore.kernel.org/r/87blunsm43.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When I re-posted Sean's original commit to add the override mode for
the kevin panel, for some reason I didn't notice that the pixel clock
wasn't quite right. Looking at /sys/kernel/debug/clk/clk_summary on
downstream kernels it can be seen that the VOP clock is supposed to be
266,666,667 Hz achieved by dividing the 800 MHz PLL by 3.
Looking at history, it seems that even Sean's first patch [1] had this
funny clock rate. I'm not sure where it came from since the commit
message specifically mentioned 26666 kHz and the Chrome OS tree [2]
can be seen to request 266667 kHz.
In any case, let's fix it up. This together with my patch [3] to do
the proper rounding when setting the clock rate makes the VOP clock
more proper as seen in /sys/kernel/debug/clk/clk_summary.
[1] https://lore.kernel.org/r/20180206165626.37692-4-seanpaul@chromium.org
[2] https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/panel/panel-simple.c#1172
[3] https://lkml.kernel.org/r/20191003114726.v2.1.Ib233b3e706cf6317858384264d5b0ed35657456e@changeid
Fixes: 84ebd2da6d04 ("arm64: dts: rockchip: Specify override mode for kevin panel")
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20191008124949.1.I674acd441997dd0690c86c9003743aacda1cf5dd@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix usb-c on X99 TV Box. Tested with armbian w/ kernel 5.3
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Link: https://lore.kernel.org/r/20190929032230.24628-1-npcomplete13@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
According to the RockPro64 schematic [1] the rk3399 sdmmc controller is
connected to a microSD (TF card) slot. Remove the cap-mmc-highspeed
property of the sdmmc controller, since no mmc card can be connected here.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191004203213.4995-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Commit 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge
sensitive interrupt") changed wlcore interrupts to use edge interrupt based
on what's specified in the wl1835mod.pdf data sheet.
However, there are still cases where we can have lost interrupts as
described in omap_gpio_unidle(). And using a level interrupt instead of edge
interrupt helps as we avoid the check for untriggered GPIO interrupts in
omap_gpio_unidle().
And with commit e6818d29ea15 ("gpio: gpio-omap: configure edge detection
for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts.
Let's change omap4 and 5 wlcore users back to using level interrupt
instead of edge interrupt. Let's not change the others as I've only seen
this on omap4 and 5, probably because the other SoCs don't have l4per idle
independent of the CPUs.
Fixes: 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt")
Depends-on: e6818d29ea15 ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup")
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Guy Mishol <guym@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update Turris Mox device tree to use the phy-supply property of the
generic PHY framework instead of the legacy usb-phy property.
This is needed since it caused a regression on Turris Mox since "usb:
host: xhci-plat: Prevent an abnormally restrictive PHY init skipping".
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: eb6c2eb6c7fb ("usb: host: xhci-plat: Prevent an abnormally restrictive PHY init skipping")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
According to
Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt,
i2c-mux-idle-disconnect is a property of a parent node since it
pertains to the mux/switch as a whole, so move it there and drop all
of the concurrences in child nodes.
Fixes: d031773169df ("ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The clkctrl code searches for the parent clockdomain based on the name
of the CM provider node. The introduction of SGX node for omap5 made
the node name for the gpu_cm to be clock-controller. There is no
clockdomain named like this, so the lookup fails. Fix by changing
the node name properly.
Fixes: 394534cb07d8 ("ARM: dts: Configure sgx for omap5")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GPIO controlled regulator for the ARM power supply is supplying
the higher voltage when the GPIO is driven high. This is opposite to
the similar regulator setup on the EVK board and is impacting stability
of the board as the ARM domain has been supplied with a too low voltage
when to faster OPPs are in use.
Fixes: 4a13b3bec3b4 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SCU firmware API for getting UID should have response,
otherwise, the message stored in function stack could be
released and then the response data received from SCU will be
stored into that released stack and cause kernel NULL pointer
dump.
Fixes: 73feb4d0f8f1 ("soc: imx-scu: Add SoC UID(unique identifier) support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The RockPro64 schematics [1], [2] show that the rk3399 EMMC_STRB pin is
connected to the RESET pin instead of the DATA_STROBE pin of the eMMC module.
So the data strobe cannot be used for its intended purpose on this board,
and so the HS400 eMMC mode is not functional. Limit the controller to HS200.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
[2] http://files.pine64.org/doc/rock64/PINE64_eMMC_Module_20170719.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191003215036.15023-2-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RockPro64 schematic [1] page 18 states a min voltage of 0.8V and a
max voltage of 1.4V for the VDD_LOG pwm regulator. However, there is an
additional note that the pwm parameter needs to be modified.
From the schematics a voltage range of 0.8V to 1.7V can be calculated.
Additional voltage measurements on the board show that this fix indeed
leads to the correct voltage, while without this fix the voltage was set
too high.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191003215036.15023-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
SPI_STM32_QSPI must be set in buildin as rootfs can be
located on QSPI memory device.
Link: https://lore.kernel.org/r/20191004124025.17394-1-patrice.chotard@st.com
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
The naming convention for the existing Theobroma boards is
soc-q7module-baseboard, so rk3399-puma-haikou and the in-kernel
devicetrees also follow that scheme.
For some reason in the binding a wrong or outdated naming slipped
in which does not match the used devicetrees and makes the dt-schema
complain now.
Fix this by using the names used in the wild by actual boards.
Fixes: a323a513c712 ("dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema")
[although the issue was also present in the old txt file]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190917083453.25744-1-heiko@sntech.de
|
|
Fix the pinctrl and interrupt specifier for RK808 to use GPIO3_B2. On the
Rockpro64 schematic [1] page 16, it shows GPIO3_B2 used for the interrupt
line PMIC_INT_L from the RK808, and there's a note which translates as:
"PMU termination GPIO1_C5 changed to this".
Tested by setting an RTC wakealarm and checking /proc/interrupts counters.
Without this patch, neither the rockchip_gpio_irq counter for the RK808,
nor the RTC alarm counter increment when the alarm time is reached.
With this patch, both interrupt counters increment by 1 as expected.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Link: https://lore.kernel.org/r/20190921131457.36258-1-sigmaris@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The old omapdrm panels got removed for v5.4 in favor of generic panels,
and the Kconfig options changed. Let's update omap2plus_defconfig
accordingly so the same panels are still enabled.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
* tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This fixes up the default ux500 CPU thermal zone:
- Set polling delay to 0 and explain why
- Set passive polling delay to 250
- Remove restrictions from the CPU cooling device,
we should use all cpufreq steps to cool down if
needed.
Link: https://lore.kernel.org/r/20191001074628.8122-1-linus.walleij@linaro.org
Fixes: b786a05f6ce4 ("ARM: dts: ux500: Update thermal zone")
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
There are total of 151 non-secure gpio (0-150) and four
pins of pinmux (91, 92, 93 and 94) are not mapped to any
gpio pin, hence update same in DT.
Fixes: 8aa428cc1e2e ("arm64: dts: Add pinctrl DT nodes for Stingray SOC")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Commit 6334150e9a36 ("remoteproc: don't allow modular build")
changes CONFIG_REMOTEPROC to a boolean from a tristate config
option which inhibits all defconfigs marking CONFIG_REMOTEPROC as
a module in compiling the remoteproc and dependent config options.
So fix the configs to have CONFIG_REMOTEPROC built in.
Link: https://lore.kernel.org/r/20190920075946.13282-5-j-keerthy@ti.com
Fixes: 6334150e9a36 ("remoteproc: don't allow modular build")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Will Deacon <will@kernel.org>
[olof: Fixed up all 4 occurrances in this one commit]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A bunch of fixes that accumulated in recent weeks, mostly material for
stable.
Summary:
- fix for regression from 5.3 that prevents to use balance convert
with single profile
- qgroup fixes: rescan race, accounting leak with multiple writers,
potential leak after io failure recovery
- fix for use after free in relocation (reported by KASAN)
- other error handling fixups"
* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
btrfs: Fix a regression which we can't convert to SINGLE profile
btrfs: relocation: fix use-after-free on dead relocation roots
Btrfs: fix race setting up and completing qgroup rescan workers
Btrfs: fix missing error return if writeback for extent buffer never started
btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
Btrfs: fix selftests failure due to uninitialized i_mode in test inodes
|
|
Pull csky updates from Guo Ren:
"This round of csky subsystem just some fixups:
- Fix mb() synchronization problem
- Fix dma_alloc_coherent with PAGE_SO attribute
- Fix cache_op failed when cross memory ZONEs
- Optimize arch_sync_dma_for_cpu/device with dma_inv_range
- Fix ioremap function losing
- Fix arch_get_unmapped_area() implementation
- Fix defer cache flush for 610
- Support kernel non-aligned access
- Fix 610 vipt cache flush mechanism
- Fix add zero_fp fixup perf backtrace panic
- Move static keyword to the front of declaration
- Fix csky_pmu.max_period assignment
- Use generic free_initrd_mem()
- entry: Remove unneeded need_resched() loop"
* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
csky: Move static keyword to the front of declaration
csky: entry: Remove unneeded need_resched() loop
csky: Fixup csky_pmu.max_period assignment
csky: Fixup add zero_fp fixup perf backtrace panic
csky: Use generic free_initrd_mem()
csky: Fixup 610 vipt cache flush mechanism
csky: Support kernel non-aligned access
csky: Fixup defer cache flush for 610
csky: Fixup arch_get_unmapped_area() implementation
csky: Fixup ioremap function losing
csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
csky/dma: Fixup cache_op failed when cross memory ZONEs
csky: Fixup dma_alloc_coherent with PAGE_SO attribute
csky: Fixup mb() synchronization problem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
|
|
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few more tracing fixes:
- Fix a buffer overflow by checking nr_args correctly in probes
- Fix a warning that is reported by clang
- Fix a possible memory leak in error path of filter processing
- Fix the selftest that checks for failures, but wasn't failing
- Minor clean up on call site output of a memory trace event"
* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Fix same probe error test
mm, tracing: Print symbol name for call_site in trace events
tracing: Have error path in predicate_parse() free its allocated memory
tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
tracing/probe: Fix to check the difference of nr_args before adding probe
|
|
Pull more MMC updates from Ulf Hansson:
"A couple more updates/fixes for MMC:
- sdhci-pci: Add Genesys Logic GL975x support
- sdhci-tegra: Recover loss in throughput for DMA
- sdhci-of-esdhc: Fix DMA bug"
* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: host: sdhci-pci: Add Genesys Logic GL975x support
mmc: tegra: Implement ->set_dma_mask()
mmc: sdhci: Let drivers define their DMA mask
mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
mmc: sdhci: improve ADMA error reporting
|
|
Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):
arch/csky/kernel/perf_event.c:1340:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
|
|
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Documentation/process update from Greg KH:
"Here are two small Documentation/process/embargoed-hardware-issues.rst
file updates that missed my previous char/misc pull request.
The first one adds an Intel representative for the process, and the
second one cleans up the text a bit more when it comes to how the
disclosure rules work, as it was a bit confusing to some companies"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Clarify disclosure rules
Documentation/process: Volunteer as the ambassador for Intel
|