summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-12-17iwlwifi: mvm: set highest rate in VHT MCS SetEyal Shapira
Set the Tx/Rx highest long GI rates in the VHT Supported MCS Set field according to the chip capabilties. Signed-off-by: Eyal Shapira <eyal@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: rs: disable MCS9 Tx workaroundEyal Shapira
MCS9 introduces some corner cases in the current rs algorithm which may lead to non optimal throughput and instability in the throughput. Until all the corner cases are resolved disable MCS9 for Tx as a workaround which yields better throughput results as MCS8 is much more stable. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Do not allow AP MAC context update if not activeIlan Peer
Fix a regression introduced in "iwlwifi: mvm: fix ht protection flags" where an AP/IBSS MAC context could have been updated even before the context was added to the FW. This fix avoids the following warning: WARNING: ... at .../drivers/net/wireless/iwlwifi/mvm/mac-ctxt.c:1132 iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]() Changing inactive MAC 0c:8b:fd:01:1a:30/3 Modules linked in: [...] Call Trace: [<c16041fd>] dump_stack+0x41/0x52 [<c1041074>] warn_slowpath_common+0x84/0xa0 [<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<c1041133>] warn_slowpath_fmt+0x33/0x40 [<f80d8f45>] iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<f80d517a>] iwl_mvm_bss_info_changed+0x22a/0x4b0 [iwlmvm] [<c160831d>] ? mutex_unlock+0xd/0x10 [<f80d4678>] ? iwl_mvm_configure_filter+0x58/0x70 [iwlmvm] [<f80d4f50>] ? iwl_mvm_mac_tx+0xc0/0xc0 [iwlmvm] [<f8132d83>] ieee80211_bss_info_change_notify+0xa3/0x1d0 [mac80211] [<f8149247>] ? ieee80211_del_virtual_monitor+0x127/0x1f0 [mac80211] [<f8149cac>] ieee80211_do_open+0x12c/0xeb0 [mac80211] [<c106c6de>] ? __raw_notifier_call_chain+0x1e/0x30 [<c106c70f>] ? raw_notifier_call_chain+0x1f/0x30 [<f814aa8d>] ieee80211_open+0x5d/0x60 [mac80211] [<c1500c7b>] __dev_open+0xab/0x140 [<c160b39a>] ? _raw_spin_unlock_bh+0x2a/0x30 [<c1500f41>] __dev_change_flags+0x81/0x160 [<c10ab6fc>] ? __lock_is_held+0x3c/0x60 [<c15010d1>] dev_change_flags+0x21/0x60 Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reported-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: fixup MakefileEmmanuel Grumbach
debufs.o appeared twice in the Makefile. Fix that. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: rs: refactor rate scale action decisionEyal Shapira
Extract the scale action decision to a different function in preparation of modifying it. While at it also convert the scale action values from hardcoded values to a clear enum. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: rs: remove unnecessary debug logsEyal Shapira
The logs are emitted in a flow in which there were retries and the rates in the rate table entry didn't match the active or search table. This doesn't indicate a problem and is expected in most cases where there will be retries for some reason. Remove the logs. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: rs: improve rates table algoEyal Shapira
The new logic will attempt more rates with less retries per rate. Also when starting off with MIMO it will fallback to SISO with the same MCS and only then to Legacy. Previously we fell back directly to Legacy. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: rs: avoid recalc of supported legacy rate maskEyal Shapira
The supported legacy rate mask is initialized when rs is initialized based on the remote peer supported rates. There's no need to re mask it repeatedly with the supported remote peer rates. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: rs: refactor building the LQ commandEyal Shapira
Simplify the code a bit more by extracting the rates table building logic into a separate function and handle setting a fixed rate for debug in a separate flow. Also avoid using and saving ucode rate format in different places. Instead use rs_rate struct and convert to ucode format only when filling the rates table in the LQ command. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Add and examine TLV flag for P2P client uAPSD supportAlexander Bondar
Current firmware doesn't handle well uAPSD in P2P Client. When it will be fixed, the firmware will set a TLV flag to notify the driver that uAPSD is supported in P2P client mode. Check this flag when sending power command for P2P client. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: trans: turn set_pmi into an optional callbackArik Nemtsov
It is not currently implemented for SDIO, and not required for other slave buses as well. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: trans: clear FW_ERROR status in common codeArik Nemtsov
Clear the FW_ERROR status before the common start_fw transport code. Remove the transport specific clears. After these patches the FW_ERROR flag is only set and cleared by common transport code. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: trans: prevent reprobe on repeated FW errors before restartArik Nemtsov
In case a sync command timeouts or Tx is stuck while a FW error interrupt arrives, we might call iwl_op_mode_nic_error twice before a restart has been initiated. This will cause a reprobe. Unify calls to this function at the transport level and only call it on the first FW error in a given by checking the transport FW error flag. While at it, remove the privately defined iwl_nic_error from PCIE code and use the common callback instead. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: check iwl_nvm_init return valueEliad Peller
iwl_nvm_init() return value wasn't checked in some path, which resulted in the following panic (if there was some issue with the nvm): Unable to handle kernel NULL pointer dereference at virtual address 00000004 pgd = d0460000 [00000004] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP Modules linked in: iwlmvm(+) iwlwifi mac80211 cfg80211 compat [last unloaded: compat] PC is at iwl_mvm_mac_setup_register+0x12c/0x460 [iwlmvm] LR is at 0x2710 pc : [<bf50dd4c>] lr : [<00002710>] psr: 20800013 sp : d00cfe18 ip : 0000081e fp : d006b908 r10: d0711408 r9 : bf532e64 r8 : d006b5bc r7 : d01af000 r6 : bf39cefc r5 : d006ab00 r4 : d006b5a4 r3 : 00000001 r2 : 00000000 r1 : d006a120 r0 : d006b860 Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: remove pointer to transport from op_modeEmmanuel Grumbach
This pointer was not used anywhere. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: rs: move rs_program_fix_rate to cleanup ifdefsEyal Shapira
Move rs_program_fix_rate right before it's caller where we're already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so we can get rid of the extra ifdefs surrounding the original location. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: trans: prevent tx and cmds during FW errorArik Nemtsov
Stop Tx and commands from arriving to the transport layer when a FW error has occurred. A HW recovery should take place before. Remove transport specific checks of the same nature (note that not all transports were protected). Signed-off-by: Arik Nemtsov <arik@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: trans: use a unified transport statusArik Nemtsov
The same bits are employed in all transport layers. Put the status field in the common transport layer. This allows us to employ them in common transport code. Signed-off-by: Arik Nemtsov <arik@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: trans: divide stop_hw into stop_device/op_mode_leaveArik Nemtsov
The stop_hw trans callback is not well defined. It is missing in many cleanup flows and the division of labor between stop_device/stop_hw is cumbersome. Remove stop_hw and use stop_device to perform both. Implement this for all current transports. PCIE needs some extra configuration the op-mode is leaving to configure RF kill. Expose this explicitly as a new op_mode_leave trans callback. Take the call to stop_device outside iwl_run_mvm_init_ucode, this makes more sense and WARN when we want to run the INIT firmware while it has run already. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: clarify smps_requests documentationJohannes Berg
The documentation for smps_requests is unclear, rewrite it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: configure phy_ctxt with min_defEliad Peller
Configure the phy context to the minimum required bandwidth, given by ctx->min_def. Tuning to a narrower bandwidth should reduce the noise level and consume less power. Signed-off-by: Eliad Peller <eliad@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: add multicast filtering supportEliad Peller
Configure the fw to filter multicast according to the addresses given by mac80211. Note that bssid should be given even if we want to pass all the multicast frames. Signed-off-by: Eliad Peller <eliad@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: move iwl_mvm_set_tx_power to PHY areaEmmanuel Grumbach
This is more related to phy contexts than to mac context. Move this function to there. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: add per-vif power debugfs hooksAlexander Bondar
This allows to tweak the power parameters per vif. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Enable power save on a single P2P client interfaceAlexander Bondar
Enable power save on P2P client interface only if it is the only bound interface. Avoid using uAPSD if P2P client is associated to GO that uses opportunistic power save. This is due to current FW limitation. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Disable power save for monitor interfaceAlexander Bondar
When monitor interface is activated device power save needs to be disabled. Re-consider power management status on other active interfaces when monitor interface is bound or unbound. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Change power management dependency on multi MACAlexander Bondar
FW still does not support power management on multiple MAC interfaces. Currently the driver enforce this limitation by disabling PM if second interface is added. Change this behavior to allow PM on a single interface even if other interfaces exist but not bound to any specific PHY. PM will be enabled if only one single interface is bound. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Add uAPSD misbehaving AP notification handlingAlexander Bondar
FW implements protective algorithm to identify AP's improper uAPSD behavior. FW sends misbehaving AP notification in this case. Add this notification handling. Avoid using uAPSD in next association to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move uAPSD related code to a separate function. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: publish Tx STBC support in VHTEyal Shapira
If the device is MIMO and VHT capable it supports Tx STBC. Unlike HT, any chip that supports VHT also support STBC so no need for a config parameter. Using num_of_ants multiple times warranted caching it. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: set VHT beamformee STS cap correctlyEyal Shapira
It was set to zero which reflects support of a single STS. Set according to the number of Rx antennas which correctly reflects the number of STSs the STA can receive in a VHT NDP. This improves beamforming and has been tested to improve Rx throughput. Signed-off-by: Eyal Shapira <eyal@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: publish STBC support in HTEyal Shapira
Not all chips support STBC so allow this to be another config parameter per chip type. If STBC is supported then publish it in the HT caps. Since 7260/7265/3160 chips support it - set the stbc support bit. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: add a generic cipher scheme supportMax Stepanov
This patch adds a cipher scheme support to extend a set of the supported ciphers. The driver reads a cipher scheme list TLV from FW image and passes it to mac80211 on hw registration. After the cipher schemes are registered the driver handles key installation and Tx/Rx calls related to the new ciphers. Signed-off-by: Max Stepanov <Max.Stepanov@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Add Smart FIFO supportLilach Edelstein
Send firmware a Smart FIFO Configuration host command to allow interrupt coalescing. The smart FIFO is enabled when there is only one bound interface (other than p2p devices which are ignored) and it is of type station, and activated while the station is associated. Smart Fifo allows aggragations of DMA transactions and by that causes processor and memory controller to stay for a longer time on lower c-states, thus saving platform power. Firmware relies on driver to activate and disable it. Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: don't send SMPS action frame with single RX antennaEmmanuel Grumbach
Products that have only 1 antenna in Rx don't support MIMO in RX. As a consequence, they will be in STATIC always. Don't tell mac80211 to update SMPS in that case. mac80211 would send an action frame to the AP which is clearly bogus. As a matter of fact, we have seen that some APs send a deauth when that happens. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: fix compilation without CONFIG_MAC80211_DEBUGFSEmmanuel Grumbach
This fixes compilation issues with CONFIG_MAC80211_DEBUGFS not enabled. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: BT Coex - enable Sync to SCOEmmanuel Grumbach
Sync to SCO is a feature that allows to synchronise the wifi activity with the predictable BT activity in SCO profile. This allows to reduce the collisions and improve overall quality. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: overhaul search cycle state machineEyal Shapira
Rewrite the search cycle state machine to use a more data oriented approach where the different Tx columns (configs) limitations and next columns to search are reprsented in tables which are easy to change. This overhaul also includes several major fixes: 1. Prevent going back to a specific Tx column in a search cycle if it was already explored. 2. Avoid switching to a Tx column that doesn't have any chance if it performs perfectly to beat the current throughput we're getting. These issues were degrading throughput as they were causing switching to "bad" Tx columns. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: use the proper channel width define for legacy rateEyal Shapira
Use the 20Mhz channel width define instead of just the number zero for legacy rates. Note that the define has the same value so this is just a minor cleanup. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: fix mapping from HT/VHT rates to legacyEyal Shapira
The table rs_ht_to_legacy is used to get the next legacy rate following the last HT or VHT rate in the LQ rates table. The mapping wasn't correct as well as didn't include entries for MCS8/9 which led to out of bounds access. This didn't trigger a crash but led to legacy rate entries using 1Mbps rate. In 5Ghz this probably caused the Tx to fail completely given that Tx attempt would have reached the legacy entries and 1Mbps isn't valid. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: set dual_stream_ant_msk to ANT_AB alwaysEyal Shapira
Drop code which was relevant when there were chips with 3 antennas. Setting to ANT_AB should be ok with all mvm supported chips. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: remove unused parameter to rs_get_supported_ratesEyal Shapira
No use of the ieee80211 header. Drop it. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: refactor to use rs_rateEyal Shapira
Introduce rs_rate which represents a rate. Use this structure instead of iwl_scale_tbl_info where we're dealing with a single rate. This avoids allocating the big iwl_scale_tbl_info structure on the stack in several cases like converting to ucode rate format or from ucode rate format. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: remove unused timestamp fieldEyal Shapira
Remove this as it's unused. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: increase stay in column timeoutEyal Shapira
Remain in the same Tx modulation (i.e. column) for a longer time before starting a search cycle for a better modulation. This has been shown to give better results. Also change the name of the timeout define to better match its description. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: rename thresholds definesEyal Shapira
Rename for clearer names. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: update expected TPT tables if aggregation changedEyal Shapira
Expected TPT table was updated only when switching to a new modulation. This is wrong as toggling aggregation changes the expected TPT signficantly. This leads to scenarios where turning aggregation on after being in MIMO sends us back to SISO despite a perfect success ratio. This occurred because the TPT of the SISO mode was being estimated based on aggregation while the MIMO one wasn't. Also remove an error print which isn't an error anymore since we might be updating the expected TPT table due to aggregation changes. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: reduce min failures to end test windowEyal Shapira
This terminates a test window of a new rate quicker in case we've hit a bad rate and should recover better. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: rs: improve debug printsEyal Shapira
Enable better tracking of different decisions made by the rate scale algorithm. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: don't configure mimo rates if nss is limited to 1Eyal Shapira
Remote peer can publish a different number of supported nss via the operating mode notification IE or action frame. If it limits to 1 then we don't want mimo rates configured in the rate table. Signed-off-by: Eyal Shapira <eyal@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-09iwlwifi: mvm: don't enable VHT MCS9 in 20MhzEyal Shapira
MCS9 in NSS=1 or NSS=2 isn't valid for 20Mhz so don't enable it in case we're dealing with a 20Mhz sta. Trying to configure an MCS9 rate with 20Mhz in the LQ rate table would lead to a FW assert. Signed-off-by: Eyal Shapira <eyal@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-17 00:28:03 +0000