| Age | Commit message (Collapse) | Author |
|---|
|
When handling a driver reset due to a failover of the backing
server on the vios, doing the netdev_notify_peers() can cause
network traffic to stall or halt. Remove the netdev notify call
for failover resets.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IBM vNIC protocol provides support for the user to initiate
a failover from the client LPAR in case the current backing infrastructure
is deemed inadequate or in an error state.
Support for two H_VIOCTL sub-commands for vNIC devices are required
to implement this function. These commands are H_GET_SESSION_TOKEN
and H_SESSION_ERR_DETECTED.
"[H_GET_SESSION_TOKEN] is used to obtain a session token from a VNIC client
adapter. This token is opaque to the caller and is intended to be used in
tandem with the SESSION_ERROR_DETECTED vioctl subfunction."
"[H_SESSION_ERR_DETECTED] is used to report that the currently active
backing device for a VNIC client adapter is behaving poorly, and that
the hypervisor should attempt to fail over to a different backing device,
if one is available."
To provide tools access to this functionality the vNIC driver creates a
sysfs file that, when written to, will send a request to pHyp to failover
to a different backing device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On GOP port 0 two MAC modes are available: GMAC and XLG. The XLG MAC is
used for 10G connectivity. This patch adds a basic 10G support by
allowing to use the XLG MAC on port 0 and by reworking the
port_enable/disable functions so that the XLG MAC is configured when
using 10G.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: port macros cosmetics
This patch series brings no functional changes.
It prefixes all common port registers macros with MV88E6XXX_PORT.
If registers or some bits differs between switch models, a reference
model is chosen (e.g. MV88E6390_PORT_MAC_CTL_SPEED_10000.)
The register names are documented as found in the datasheets.
Avoid BIT() and shifts defines and prefer a better representation of the
Marvell switch registers with ordered, hexadecimal, 16-bit values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the remaining common Port
Registers macros with MV88E6XXX_PORT.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port IEEE
Priority Remapping registers macros with MV88E6095_PORT_IEEE_PRIO.
The 88E6390 family turned the 0x18 register into a single indirect
table, document that at the same time.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Also fix the following checkpatch checks with a temporary variable:
CHECK: Alignment should match open parenthesis
#65: FILE: drivers/net/dsa/mv88e6xxx/port.c:932:
+ err = mv88e6xxx_port_ieeepmt_write(chip, port,
+ MV88E6390_PORT_IEEE_PRIO_MAP_TABLE_INGRESS_PCP,
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Association
Vector Register macros with MV88E6XXX_PORT_ASSOC_VECTOR.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Egress Rate
Control and Port Egress Rate Control 2 registers macros with
MV88E6XXX_PORT_EGRESS_RATE_CTL1 and MV88E6XXX_PORT_EGRESS_RATE_CTL2.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Control 2
Register macros with MV88E6XXX_PORT_CTL2 and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6095_PORT_CTL2_CPU_PORT_MASK.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Default
VLAN Register macros with MV88E6XXX_PORT_DEFAULT_VLAN.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Based VLAN
Register macros with MV88E6XXX_PORT_BASE_VLAN.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Control 1
Register macros with MV88E6XXX_PORT_CTL1.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Control
Register macros with MV88E6XXX_PORT_CTL0 and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6185_PORT_CTL0_USE_TAG.)
The reason for CTL0 is to make it clear between the badly named
"Port Control", "Port Control 1" and "Port Control 2" registers.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Switch ID
Register macros with MV88E6XXX_PORT_SWITCH_ID.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers, this means shifting their values by 4.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Jamming
Control Register macros with MV88E6XXX_PORT_JAM_CTL and the ones which
differ between implementations with a chosen reference model
(e.g. MV88E6097_PORT_JAM_CTL.)
The 88E6390 family renamed the register to Flow Control and turned it
into an indirect table. Document that as well.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common MAC Control
Register macros with MV88E6XXX_PORT_MAC_CTL and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6065_PORT_MAC_CTL_SPEED_200.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implicit namespacing and clarity, prefix the common Port Status
Register macros with MV88E6XXX_PORT_STS and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6352_PORT_STS_EEE.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Give back all modes advertised by the link partner. This change brings
the marvell phy driver in line with all other phy drivers.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes vxlan_snoop to not move permanent fdb entries
on learn events. This is consistent with the bridge fdb
handling of permanent entries.
Fixes: 26a41ae60438 ("vxlan: only migrate dynamic FDB entries")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
udp: reduce cache pressure
In the most common use case, many skb fields are not used by recvmsg(), and
the few ones actually accessed lays on cold cachelines, which leads to several
cache miss per packet.
This patch series attempts to reduce such misses with different strategies:
* caching the interesting fields in the scratched space
* avoid accessing at all uninteresting fields
* prefetching
Tested using the udp_sink program by Jesper[1] as the receiver, an h/w l4 rx
hash on the ingress nic, so that the number of ingress nic rx queues hit by the
udp traffic could be controlled via ethtool -L.
The udp_sink program was bound to the first idle cpu, to get more
stable numbers.
On a single numa node receiver:
nic rx queues vanilla patched kernel delta
1 1850 kpps 1850 kpps 0%
2 2370 kpps 2700 kpps 13.9%
16 2000 kpps 2220 kpps 11%
[1] https://github.com/netoptimizer/network-testing/blob/master/src/udp_sink.c
v1 -> v2:
- replaced secpath_reset() with skb_release_head_state()
- changed udp_dev_scratch fields types to u{32,16} variant,
replaced bitfield with bool
v2 -> v3:
- no changes, tested against apachebench for performances regression
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when udp_recvmsg() is executed, on x86_64 and other archs, most skb
fields are on cold cachelines.
If the skb are linear and the kernel don't need to compute the udp
csum, only a handful of skb fields are required by udp_recvmsg().
Since we already use skb->dev_scratch to cache hot data, and
there are 32 bits unused on 64 bit archs, use such field to cache
as much data as we can, and try to prefetch on dequeue the relevant
fields that are left out.
This can save up to 2 cache miss per packet.
v1 -> v2:
- changed udp_dev_scratch fields types to u{32,16} variant,
replaced bitfiled with bool
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since UDP no more uses sk->destructor, we can clear completely
the skb head state before enqueuing. Amend and use
skb_release_head_state() for that.
All head states share a single cacheline, which is not
normally used/accesses on dequeue. We can avoid entirely accessing
such cacheline implementing and using in the UDP code a specialized
skb free helper which ignores the skb head state.
This saves a cacheline miss at skb deallocation time.
v1 -> v2:
replaced secpath_reset() with skb_release_head_state()
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same code is replicated in 3 different places; move it to a
common helper.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware supports the MTU to be changed and the driver it self is
somewhat prepared to support this. This patch hooks up the callbacks to
be able to change the MTU from user-space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of recently implemented stack_depth tracking for arm64 JIT,
so that stack usage can be reduced heavily for programs not using
tail calls at least.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-06-11
This series provides updates to mlx5 header rewrite feature, from Or Gerlitz.
and three more small updates From maor and eran.
-------
Or says:
Packets belonging to flows which are different by matching may still need
to go through the same header re-writes (e.g set the current routing hop
MACs and issue TTL decrement). To minimize the number of modify header
IDs, we add a cache for header re-write IDs which is keyed by the binary
chain of modify header actions.
The caching is supported for both eswitch and NIC use-cases, where the
actual conversion of the code to use caching comes in separate patches,
one per use-case.
Using a per field mask field, the TC pedit action supports modifying
partial fields. The last patch enables offloading that.
-------
From Maor, update flow table commands layout to the latest HW spec.
From Eran, ethtool connector type reporting updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPSW driver does not handle this interrupt, so there are no reasons to enable
it in hardware.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPSW driver supports PTP v1 messages, but for unknown reasons this filter
is not advertised. As result,
./tools/testing/selftests/networking/timestamping/timestamping utility
can't be used for testing of CPSW RX timestamping with option
SOF_TIMESTAMPING_RX_HARDWARE, because it uses
HWTSTAMP_FILTER_PTP_V1_L4_SYNC filter.
Hence, fix it by advertising HWTSTAMP_FILTER_PTP_V1_L4_XXX filters
in CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
Misc BPF updates
This set contains a couple of misc updates: stack usage reduction
for perf_sample_data in tracing progs, reduction of stale data in
verifier on register state transitions that I still had in my queue
and few selftest improvements as well as bpf_set_hash() helper for
tc programs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow for tc BPF programs to set a skb->hash, apart from clearing
and triggering a recalc that we have right now. It allows for BPF
to implement a custom hashing routine for skb_get_hash().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since cg_skb_func_proto() doesn't do anything else than just calling
into sk_filter_func_proto(), remove it and set sk_filter_func_proto()
directly for .get_func_proto callback.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running all the tests, through 'make run_tests', I had
test_align failing due to insufficient rlimit. Set it the same
way as all other test cases from BPF selftests do, so that
test case properly loads everything.
[...]
Summary: 7 PASSED, 1 FAILED
selftests: test_progs [PASS]
/home/foo/net-next/tools/testing/selftests/bpf
Test 0: mov ... Failed to load program.
FAIL
Test 1: shift ... Failed to load program.
FAIL
Test 2: addsub ... Failed to load program.
FAIL
Test 3: mul ... Failed to load program.
FAIL
Test 4: unknown shift ... Failed to load program.
FAIL
Test 5: unknown mul ... Failed to load program.
FAIL
Test 6: packet const offset ... Failed to load program.
FAIL
Test 7: packet variable offset ... Failed to load program.
FAIL
Results: 0 pass 8 fail
selftests: test_align [PASS]
[...]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test case to track behaviour when traversing and updating the
htab map. We recently used such traversal, so it's quite useful to
keep it as an example in selftests.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Right now, we don't reset the id of spilled registers in case of
clear_all_pkt_pointers(). Given pkt_pointers are highly likely to
contain an id, do so by reusing __mark_reg_unknown_value().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whenever we set the register to the type CONST_IMM, we currently don't
reset the id to 0. id member is not used in CONST_IMM case, so don't
let it become stale, where pruning won't be able to match later on.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
spilled_regs[] state is only used for stack slots of type STACK_SPILL,
never for STACK_MISC. Right now, in states_equal(), even if we have
old and current stack state of type STACK_MISC, we compare spilled_regs[]
for that particular offset. Just skip these like we do everywhere else.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
perf_sample_data consumes 386 bytes on stack, reduce excessive stack
usage and move it to per cpu buffer. It's allowed due to preemption
being disabled for tracing, xdp and tc programs, thus at all times
only one program can run on a specific CPU and programs cannot run
from interrupt. We similarly also handle bpf_pt_regs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2b30842b23b9 ("net: fec: Clear and enable MIB counters on imx51")
introduced fec_enet_clear_ethtool_stats(), but missed to add a stub
for the CONFIG_M5272=y case, causing build failure for the
m5272c3_defconfig.
Add the missing empty stub to fix the build failure.
Fixes: Commit 2b30842b23b9 ("net: fec: Clear and enable MIB counters on imx51")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After moves the skb->dev and skb->protocol initialization into
ip6_output, setting the skb->dev inside ip6_fragment is unnecessary.
Fixes: 97a7a37a7b7b("ipv6: Initial skb->dev and skb->protocol in ip6_output")
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sctp_assoc_set_id does the assoc id check in the beginning when
processing dupcookie, no need to do the same check before calling
it.
v1->v2:
fix some typo errs Marcelo pointed in changelog.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to use read_lock_bh instead of local_bh_disable
and read_lock in sctp_eps_seq_show.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry got the following recursive locking report while running syzkaller
fuzzer, the Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x2ee/0x3ef lib/dump_stack.c:52
print_deadlock_bug kernel/locking/lockdep.c:1729 [inline]
check_deadlock kernel/locking/lockdep.c:1773 [inline]
validate_chain kernel/locking/lockdep.c:2251 [inline]
__lock_acquire+0xef2/0x3430 kernel/locking/lockdep.c:3340
lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
lock_sock_nested+0xcb/0x120 net/core/sock.c:2536
lock_sock include/net/sock.h:1460 [inline]
sctp_close+0xcd/0x9d0 net/sctp/socket.c:1497
inet_release+0xed/0x1c0 net/ipv4/af_inet.c:425
inet6_release+0x50/0x70 net/ipv6/af_inet6.c:432
sock_release+0x8d/0x1e0 net/socket.c:597
__sock_create+0x38b/0x870 net/socket.c:1226
sock_create+0x7f/0xa0 net/socket.c:1237
sctp_do_peeloff+0x1a2/0x440 net/sctp/socket.c:4879
sctp_getsockopt_peeloff net/sctp/socket.c:4914 [inline]
sctp_getsockopt+0x111a/0x67e0 net/sctp/socket.c:6628
sock_common_getsockopt+0x95/0xd0 net/core/sock.c:2690
SYSC_getsockopt net/socket.c:1817 [inline]
SyS_getsockopt+0x240/0x380 net/socket.c:1799
entry_SYSCALL_64_fastpath+0x1f/0xc2
This warning is caused by the lock held by sctp_getsockopt() is on one
socket, while the other lock that sctp_close() is getting later is on
the newly created (which failed) socket during peeloff operation.
This patch is to avoid this warning by use lock_sock with subclass
SINGLE_DEPTH_NESTING as Wang Cong and Marcelo's suggestion.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes unneeded forward declaration of tpacket_snd()
in net/packet/af_packet.c.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two tcp_filter hooks in tcp_ipv6 ingress path currently.
One is at tcp_v6_rcv and another is in tcp_v6_do_rcv. It seems the
tcp_filter() call inside tcp_v6_do_rcv is redundent and some packet
will be filtered twice in this situation. This will cause trouble
when using eBPF filters to account traffic data.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Goal is to advertise the user when ethtool speeds and 802.3ad speeds are
desynchronized.
When this case happens, the kernel needs to be patched.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the user tries to assign a specific nsid, idr_alloc() is called with
the range [nsid, nsid+1]. If this nsid is already used, idr_alloc() returns
ENOSPC (No space left on device). In our case, it's better to return
EEXIST to make it clear that the nsid is not available.
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It helps the user to identify errors.
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free up mbox_log allocated for PF0 to PF3.
Fixes: 7829451c695e ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_QED_SRIOV is disabled, we get a build error:
drivers/net/ethernet/qlogic/qed/qed_int.c: In function 'qed_int_sb_init':
drivers/net/ethernet/qlogic/qed/qed_int.c:1499:4: error: implicit declaration of function 'qed_vf_set_sb_info'; did you mean 'qed_mcp_get_resc_info'? [-Werror=implicit-function-declaration]
All the other declarations have a 'static inline' stub as an alternative
here, so this adds one more for qed_int_sb_init.
Fixes: 50a207147fce ("qed: Hold a single array for SBs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
