summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-11-29iwlwifi: return real info in probe failureEmmanuel Grumbach
Don't return a hard coded -EFAULT, but rather the error that occurred in the flow. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-28iwlwifi: clear trans->op_mode pointer when it is leavingEmmanuel Grumbach
Since the op_mode is leaving, the transport should set its pointer to it to NULL to not point to freed memory. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-28iwlwifi: read the Rx write pointer only onceEmmanuel Grumbach
The FH (DMA engine) tells the driver the index of the last ready (closed) Rx buffer. This data is in closed_rb_num. If we read this data several times we may get inconsistencies between the code and the debug prints which can make it harder to debug issues here. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-21iwlwifi: remove effectless assignmentEmmanuel Grumbach
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: Remove duplicate inclusion of iwl-trans.h in pcie/drv.cSachin Kamat
iwl-trans.h was included twice. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: update the RB_TIMEOUT to 0x11Emmanuel Grumbach
This will allow to reduce slightly the number of interrupts without sacrificing too much the latency in the Rx path. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: make iwl_pcie_rxq_inc_wr_ptr staticEmmanuel Grumbach
It is not used outside pcie/rx.c. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: more cleanup in pcie/rx.cEmmanuel Grumbach
Really trivial clean up. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: make iwl_queue_used return boolEmmanuel Grumbach
Also, prefer the if(!X) notation over if(X == 0). Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: disallow MFP with software cryptoJohannes Berg
When software crypto is enabled, it isn't safe to enable MFP since the firmware interprets some management packets, and with MFP it would do so without proper validation. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: merge 2 functions in reclaim flowEmmanuel Grumbach
One one just a wrapper of the second, squash them. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: continue clean up - pcie/tx.cEmmanuel Grumbach
Rename static functions. Function moved from trans.c to tx.c. A few could be made static, others had to be exported. Functions that implement the transport API are prefixed by iwl_trans_pcie_, the others by iwl_pcie_. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: continue clean up - pcie/trans.cEmmanuel Grumbach
Functions that implement the transport API are prefixed by iwl_trans_pcie_, the others by iwl_pcie_. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: continue clean up - pcie/rx.cEmmanuel Grumbach
Rename static functions. Function moved from trans.c to rx.c. A few could be made static, others had to be exported. Also, don't use rxb or rxbuf, but rb which stands for receive buffer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: init the replenish work in rx_initEmmanuel Grumbach
This is its natural place Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: rename functions in transport layerEmmanuel Grumbach
1) s/tx_queue/txq for the sake of consistency. 2) s/rx_queue/rxq for the sake of consistency. 3) Make all functions begin with iwl_pcie_ iwl_queue_init and iwl_queue_space are an exception since they are not PCIE specific although they are in pcie subdir. 4) s/trans_pcie_get_cmd_string/get_cmd_string it is much shorter and used in debug prints which are long lines. 5) s/iwl_bg_rx_replenish/iwl_pcie_rx_replenish_work this better emphasizes that it is a work 6) remove invalid kernelDOC markers pcie/tx.c and pcie/trans.c still needs to be cleaned up. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19iwlwifi: add comments for the PCIe transport statusesEmmanuel Grumbach
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-14iwlwifi: don't enable interrupt as a W/A when MSI is enabledEmmanuel Grumbach
This is not needed, the comment there was wrong, it is only needed when MSI was *not* enabled. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-14iwlwifi: don't warn if transport's allocation failedEmmanuel Grumbach
The allocation failure will already be very verbose. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-09iwlwifi: return commands with error on FW errorJohannes Berg
When a firmware error occurs, don't just abort synchronous commands but also return an error (-EIO) and block any new commands as well. Currently, an error is only returned if WANT_SKB was set which is confusing and can lead to issues. Blocking is done until a new firmware image is loaded. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07iwlwifi: fix typo in RX data tracingJohannes Berg
The printk message should say RX, not TX. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07iwlwifi: remove useless messagesJohannes Berg
There's no need to print the PCI resource length and base address, nor the hardware revision ID (which can be found in lspci) Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07iwlwifi: remove SKU/antenna messages by defaultJohannes Berg
There's no reason to print these all the time, the messages aren't all that interesting. Leave them as DEBUG_INFO though, just in case. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07iwlwifi: remove EEPROM version message by defaultJohannes Berg
If the EEPROM reading was successful, don't print a message by default, the EEPROM version isn't all that interesting. Change the message to DEBUG_INFO priority so it can still be obtained. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-05iwlwifi: zero trans_cfg before settings its fieldsEmmanuel Grumbach
People tend not to set the fields they want to leave as 0. So make sure the struct is zeroed properly. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-05iwlwifi: check the SCD conf from ALIVE responseEmmanuel Grumbach
The ALIVE response of new fw inclues the base address of the SCD in SRAM. Until we read it from a prph register, which was set by the fw. Since the fw might well stop updating the prph register, add a WARN when there is an inconsitency between the ALIVE response and the register to catch any change in the behavior. Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-05iwlwifi: use list_first_entryJohannes Berg
Instead of open-coding it with a temporary list_head pointer, just use list_first_entry. Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-05iwlwifi: fix queue flush confusionJohannes Berg
The flush_control parameter to iwlagn_txfifo_flush is passed as an internal value (context flags) and then sent to the device, that can't be right. Fix the confusion by removing the parameter, always use IWL_DROP_ALL that is redefined according to the firmware API in the flush control. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-05iwlwifi: don't clear CTL_AMPDU on frame statusJohannes Berg
There's no reason to clear the CTL_AMPDU flag on transmitted frame status, it's not used by the driver here and mac80211 only uses it for some rate statistics. Also remove a stray space in the function. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-05iwlwifi: fix flush commandJohannes Berg
The flush command really flushes queues, not FIFOs, and the first 32 bits indicate the queues to flush, not FIFOs. Change the command accordingly. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-31iwlwifi: don't call stop_device twiceEmmanuel Grumbach
When we unregister from mac80211 it will down the device anyway. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-31iwlwifi: handle RFKILL logic in the transport layerEmmanuel Grumbach
No HCMD can be sent while RFKILL is asserted. If a SYNC command is running while RFKILL is asserted the fw will silently discard it. This means that the driver needs to wake the process that sleeps on the CMD_SYNC. Since the RFKILL interrupt is handled in the transport layer and the code that sleeps in CMD_SYNC is also in the transport layer, all this logic can be handled there. This simplifies the work of the op_mode. So the transport layer will now return -ERFKILL when a CMD is sent and RFKILL is asserted. This will be the case even when the CMD is SYNC. The transport layer will return -ERFKILL straight away. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-29iwlwifi: clarify NOCOPY/DUP documentationJohannes Berg
Clarify the documentation to indicate that these flags can only be used at the end, i.e. after them a copy TFD (no flags set) is invalid. Reported-by: Inbal Hacohen <inbal.hacohen@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-29iwlwifi: support host command with copied dataJohannes Berg
In addition to the NOCOPY flag, add a DUP flag that tells the transport to kmemdup() the buffer and free it after the command completes. Currently this is only supported for a single buffer in a given command, but that could be extended if it should be needed. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-23iwlwifi: remove MFP Kconfig optionAssaf Krauss
Remove the Kconfig option CONFIG_IWLWIFI_EXPERIMENTAL_MFP, if the firmware doesn't support MFP then the user shouldn't have the option to enable it as it won't work correctly. Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-23iwlwifi: don't leak Tx skb when a queue is disabledEmmanuel Grumbach
Since the queue might not be empty, we need to free the pending Tx packets. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: don't WARN when a non empty queue is disabledEmmanuel Grumbach
This can happen when we shut down suddenly an interface. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: don't print the Intel banner twiceEmmanuel Grumbach
Once in bus enumeration is enough, no need to print it again when the op_mode loads. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: first deactivate a queue, then wipe out its dataEmmanuel Grumbach
Doing the opposite is wrong, the SCD wouldn't like someone to clear its data while the queue is still active. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: use the new macro for the SCD Q STTS bitsEmmanuel Grumbach
Instead of hardcoding the expression, use the macro provided in the previous patch. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: wipe out the status of the SCD when we disable a queueEmmanuel Grumbach
When we disable a queue, we don't want the SCD to remember anything about this queue (what packet was transmitted but not acked, what packed was acked etc...). Wipe out all this data in its SRAM. Constify the arguments to iwl_write_targ_mem_dwords on the way. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: remove unused variablesJohannes Berg
Remove a number of variables that are assigned, but not used. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: make data frame tracing optionalJohannes Berg
When tracing in iwlwifi, we get all data. Most of the time, we don't need it, and it just takes up a lot of extra space in the trace. Make this optional by recording the data into two separate trace events if it is needed. Without it, record only the content of non-data and EAPOL TX frames. As a result, tracing without the data tracepoints will record meta information including the 802.11 headers for all frames but will not record the contents of data frames to reduce trace overhead. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16iwlwifi: improve oversized command warningJohannes Berg
When warning about a command that is too large, print out the command name/ID to help figure out which place is attempting to send a command that is too large. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-14Linux 3.7-rc1Linus Torvalds
2012-10-14Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds
Pull MIPS update from Ralf Baechle: "Cleanups and fixes for breakage that occured earlier during this merge phase. Also a few patches that didn't make the first pull request. Of those is the Alchemy work that merges code for many of the SOCs and evaluation boards thus among other code shrinkage, reduces the number of MIPS defconfigs by 5." * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits) MIPS: SNI: Switch RM400 serial to SCCNXP driver MIPS: Remove unused empty_bad_pmd_table[] declaration. MIPS: MT: Remove kspd. MIPS: Malta: Fix section mismatch. MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets. MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code. MIPS: Alchemy: merge PB1550 support into DB1550 code MIPS: Alchemy: Single kernel for DB1200/1300/1550 MIPS: Optimize TLB refill for RI/XI configurations. MIPS: proc: Cleanup printing of ASEs. MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required. MIPS: Add detection of DSP ASE Revision 2. MIPS: Optimize pgd_init and pmd_init MIPS: perf: Add perf functionality for BMIPS5000 MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP MIPS: perf: Remove unnecessary #ifdef MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt) MIPS: perf: Change the "mips_perf_event" table unsupported indicator. MIPS: Align swapper_pg_dir to 64K for better TLB Refill code. vmlinux.lds.h: Allow architectures to add sections to the front of .bss ...
2012-10-14Merge branch 'modules-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux Pull module signing support from Rusty Russell: "module signing is the highlight, but it's an all-over David Howells frenzy..." Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG. * 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits) X.509: Fix indefinite length element skip error handling X.509: Convert some printk calls to pr_devel asymmetric keys: fix printk format warning MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking MODSIGN: Make mrproper should remove generated files. MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs MODSIGN: Use the same digest for the autogen key sig as for the module sig MODSIGN: Sign modules during the build process MODSIGN: Provide a script for generating a key ID from an X.509 cert MODSIGN: Implement module signature checking MODSIGN: Provide module signing public keys to the kernel MODSIGN: Automatically generate module signing keys if missing MODSIGN: Provide Kconfig options MODSIGN: Provide gitignore and make clean rules for extra files MODSIGN: Add FIPS policy module: signature checking hook X.509: Add a crypto key parser for binary (DER) X.509 certificates MPILIB: Provide a function to read raw data into an MPI X.509: Add an ASN.1 decoder X.509: Add simple ASN.1 grammar compiler ...
2012-10-14x86, boot: Explicitly include autoconf.h for hostprogsMatt Fleming
The hostprogs need access to the CONFIG_* symbols found in include/generated/autoconf.h. But commit abbf1590de22 ("UAPI: Partition the header include path sets and add uapi/ header directories") replaced $(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary include paths. This has the undesirable effect of breaking the EFI boot stub because the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is never compiled. It should also be noted that because $(USERINCLUDE) isn't exported by the top-level Makefile it's actually empty in arch/x86/boot/Makefile. Cc: H. Peter Anvin <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-10-14perf: Fix UAPI falloutIngo Molnar
The UAPI commits forgot to test tooling builds such as tools/perf/, and this fixes the fallout. Manual conversion. Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-10-13Merge branch 'late-for-linus' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull ARM update from Russell King: "This is the final round of stuff for ARM, left until the end of the merge window to reduce the number of conflicts. This set contains the ARM part of David Howells UAPI changes, and a fix to the ordering of 'select' statements in ARM Kconfig files (see the appropriate commit for why this happened - thanks to Andrew Morton for pointing out the problem.) I've left this as long as I dare for this window to avoid conflicts, and I regenerated the config patch yesterday, posting it to our mailing list for review and testing. I have several acks which include successful test reports for it. However, today I notice we've got new conflicts with previously unseen code... though that conflict should be trivial (it's my changes vs a one liner.)" * 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm: ARM: config: make sure that platforms are ordered by option string ARM: config: sort select statements alphanumerically UAPI: (Scripted) Disintegrate arch/arm/include/asm Fix up fairly conflict in arch/arm/Kconfig (the select re-organization vs recent addition of GENERIC_KERNEL_EXECVE)
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-14 19:54:39 +0000