summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-06-23batman-adv: only drop packets of known wifi clientsMarek Lindner
bug introduced with 59b699cdee039d75915c354da06937102d1f9a84 If the source or destination mac address of an ethernet packet could not be found in the translation table the packet was dropped if AP isolation was turned on. This behavior would make it impossible to send broadcast packets over the mesh as the broadcast address will never enter the translation table. Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Antonio Quartulli <ordex@autistici.org>
2012-06-22net: sh_eth: fix the condition to fix the cur_tx/dirty_rxYoshihiro Shimoda
The following commit couldn't work if the RMCR is not set to 1. "net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens" commit id 79fba9f51755c704c0a7d7b7f0df10874dc0a744 If RMCR is not set, the controller will clear the EDRRR after it received a frame. In this case, the driver doesn't need to fix the value of cur_rx/dirty_rx. The driver only needs it when the controll detects receive descriptors are empty. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-22r8169: RxConfig hack for the 8168evl.françois romieu
The 8168evl (RTL_GIGA_MAC_VER_34) based Gigabyte GA-990FXA motherboards are very prone to NETDEV watchdog problems without this change. See https://bugzilla.kernel.org/show_bug.cgi?id=42899 for instance. I don't know why it *works*. It's depressingly effective though. For the record: - the problem may go along IOMMU (AMD-Vi) errors but it really looks like a red herring. - the patch sets the RX_MULTI_EN bit. If the 8168c doc is any guide, the chipset now fetches several Rx descriptors at a time. - long ago the driver ignored the RX_MULTI_EN bit. e542a2269f232d61270ceddd42b73a4348dee2bb changed the RxConfig settings. Whatever the problem it's now labeled a regression. - Realtek's own driver can identify two different 8168evl devices (CFG_METHOD_16 and CFG_METHOD_17) where the r8169 driver only sees one. It sucks. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-22usbnet: handle remote wakeup asapMing Lei
If usbnet is resumed by remote wakeup, generally there are some packets comming to be handled, so allocate and submit rx URBs in usbnet_resume to avoid delays introduced by tasklet. Otherwise, usbnet may have been runtime suspended before the usbnet_bh is executed to schedule Rx URBs. Without the patch, usbnet can't recieve any packets from peer in runtime suspend state if runtime PM is enabled and autosuspend_delay is set as zero. Signed-off-by: Ming Lei <ming.lei@canonical.com> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-22usbnet: decrease suspend count if returning -EBUSY for runtime suspendMing Lei
This patch decreases dev->suspend_count in the -EBUSY failure path of usbnet_suspend. Without the change, the later runtime suspend will do nothing except for increasing dev->suspend_count. Signed-off-by: Ming Lei <ming.lei@canonical.com> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-22usbnet: clear OPEN flag in failure pathMing Lei
Without clearing OPEN flag in failure path, runtime or system resume may submit interrupt/rx URB and start tx queue mistakenly on a interface in DOWN state. Signed-off-by: Ming Lei <ming.lei@canonical.com> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-22net: qmi_wwan: fix Gobi device probingBjørn Mork
Ignoring interfaces with additional descriptors is not a reliable method for locating the correct interface on Gobi devices. There is at least one device where this method fails: https://bbs.archlinux.org/viewtopic.php?id=143506 The result is that the AT command port (interface #2) is hidden from qcserial, preventing traditional serial modem usage: [ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device [ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22 [ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device [ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22 [ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected [ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0 [ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected [ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1 Use static interface numbers taken from the interface map in qcserial for all Gobi devices instead: Gobi 1K USB layout: 0: serial port (doesn't respond) 1: serial port (doesn't respond) 2: AT-capable modem port 3: QMI/net Gobi 2K+ USB layout: 0: QMI/net 1: DM/DIAG (use libqcdm from ModemManager for communication) 2: AT-capable modem port 3: NMEA This should be more reliable over all, and will also prevent the noisy "probe failed" messages. The whitelisting logic is expected to be replaced by direct interface number matching in 3.6. Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de> Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z Cc: <stable@vger.kernel.org> # v3.4 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-22Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2012-06-20ath9k_htc: configure bssid on ASSOC/IBSS changeRajkumar Manoharan
After the change "mac80211: remove spurious BSSID change flag", BSS_CHANGED_BSSID will not be passed on association or IBSS status changes. So it could be better to program bssid on ASSOC or IBSS change notification. Not doing so, is affecting the packet transmission. Cc: stable@vger.kernel.org [3.4+] Reported-by: Michael Leun <lkml20120218@newton.leun.net> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20iwlwifi: remove log_event debugfs file debugging is disabledJohannes Berg
When debugging is disabled, the event log functions aren't functional in the way that the debugfs file expects. This leads to the debugfs access crashing. Since the event log functions aren't functional then, remove the debugfs file when CONFIG_IWLWIFI_DEBUG is not set. Cc: stable@kernel.org Reported-by: Lekensteyn <lekensteyn@gmail.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20ath9k_hw: avoid possible infinite loop in ar9003_get_pll_sqsum_dvcMohammed Shafi Shajakhan
"ath9k: Fix softlockup in AR9485" with commit id 64bc1239c790e051ff677e023435d770d2ffa174 fixed the reported issue, yet its better to avoid the possible infinite loop in ar9003_get_pll_sqsum_dvc by having a timeout as suggested by ath9k maintainers. http://www.spinics.net/lists/linux-wireless/msg92126.html. Based on my testing PLL's locking measurement is done in ~200us (2 iterations). Cc: stable@vger.kernel.org Cc: Rolf Offermanns <rolf.offermanns@gmx.net> Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20wl1251: Fix memory leaks in SPI initializationGrazvydas Ignotas
This patch fixes two memory leaks in the SPI initialization code. Patch based on old maemo patch by: Yuri Ershov <ext-yuri.ershov@nokia.com> Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20wl1251: always report beacon loss to the stackGrazvydas Ignotas
Always report beacon loss to the stack, not only when in powersave state. This is because there's possibility that the driver disables PSM before it handles old BSS_LOSE_EVENT, so beacon loss has to be reported. Patch based on old maemo patch by: Janne Ylalehto <janne.ylalehto@nokia.com> Juuso Oikarinen <juuso.oikarinen@nokia.com> Luciano Coelho <luciano.coelho@nokia.com> Yuri Ershov <ext-yuri.ershov@nokia.com> Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20wl1251: fix TSF calculationGrazvydas Ignotas
Cast MSB part of current TSF to u64 to prevent loss of most significant bits. MSB should also be shifted by 32. Patch based on old maemo patch by: Yuri Kululin <ext-yuri.kululin@nokia.com> Yuri Ershov <ext-yuri.ershov@nokia.com> Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20ixgbe: Fix memory leak in ixgbe when receiving traffic on DDP enabled ringsAlexander Duyck
This patch fixes a memory leak that was introduced in the 3.4 kernel. The leak occurred when FCoE was enabled and traffic was passed over the FCoE rings reserved for FCoE. The memory leak was due to us not populating the compound page information on the order 1 pages needed for FCoE. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-06-20Kconfig: Fix Kconfig for Intel ixgbe and igb PTP support.Carolyn Wyborny
Fix Kconfig file to make sure that PTP and IGB/IXGBE are both either in-kernel or modules, not mixed. Having the build status mixed causes compile errors. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-06-20igb: Fix incorrect RAR address entries for i210/i211 device.Carolyn Wyborny
i210/i211 device has only 16 RAR address filters like 82575, instead of 32 like i350. This patch removes the entries for i210/i211 in the get_invariants function which was setting them for 32. This ensures that they will get the default value which is the correct one. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-06-19batman-adv: fix skb->data assignmentAntonio Quartulli
skb_linearize(skb) possibly rearranges the skb internal data and then changes the skb->data pointer value. For this reason any other pointer in the code that was assigned skb->data before invoking skb_linearise(skb) must be re-assigned. In the current tt_query message handling code this is not done and therefore, in case of skb linearization, the pointer used to handle the packet header ends up in pointing to free'd memory. This bug was introduced by a73105b8d4c765d9ebfb664d0a66802127d8e4c7 (batman-adv: improved client announcement mechanism) Signed-off-by: Antonio Quartulli <ordex@autistici.org> Cc: <stable@vger.kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19Merge branch 'for-upstream' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
2012-06-19mwifiex: fix wrong return values in add_virtual_intf() error casesBing Zhao
add_virtual_intf() needs to return an ERR_PTR(), instead of NULL, on errors, otherwise cfg80211 will crash. Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19airo: copying wrong data in airo_get_aplist()Dan Carpenter
"qual" used to be declared on the stack, but then in 998a5a7d6a ("airo: reduce stack memory footprint") we made it dynamically allocated. Unfortunately the memcpy() here was missed and it's still copying stack memory instead of the data that we want. In other words, "&qual" should be "qual". Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19mwifiex: fix uAP TX packet timeout issueAvinash Patil
When running heavy traffic we stop the tx queue if the pending packet count reaches certain threshold. Later, the tx queue should be woken up as soon as the packet count falls below the threshold. Current code wakes TX queue up on STA interface only. Removing the check for STA interface will allow both STA and AP interfaces to resume transmit when tx_pending count becomes low. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19ath5k: remove _bh from inner locksBob Copeland
spin_unlock_bh(&txq->lock) already disables softirqs so we don't want to do it here. Fixes smatch warnings: drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:' drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:' Reported-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19ath9k: fix invalid pointer access in the tx pathFelix Fietkau
After setup_frame_info has been called, only info->control.rates is still valid, other control fields have been overwritten by the ath_frame_info data. Move the access to info->control.vif for checking short preamble to setup_frame_info before it gets overwritten. This regression was introduced in commit d47a61aa "ath9k: Fix multi-VIF BSS handling" Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de> Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Cc: stable@vger.kernel.org [3.4] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19ath9k: fix a tx rate duration calculation bugFelix Fietkau
The rate pointer variable for a rate series is used in a loop before it is initialized. This went unnoticed because it was used earlier for the RTS/CTS rate. This bug can lead to the wrong PHY type being passed to the duration calculation function. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19phy/micrel: change phy_id_mask for KSZ9021 and KS8001Jason Wang
On a freescale imx6q platform, a hardware phy chip KSZ9021 is recognized as a KS8001 chip by the current driver like this: eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721] KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id 0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't distinguish them. So change phy_id_mask to resolve this problem. Although the micrel datasheet says that the 4 LSB of phyid2 register contains the chip revision number and the current driver is designed to follow this rule, in reality the chip implementation doesn't follow it. Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Hui Wang <jason77.wang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19sctp: fix warning when compiling without IPv6Daniel Halperin
net/sctp/protocol.c: In function ‘sctp_addr_wq_timeout_handler’: net/sctp/protocol.c:676: warning: label ‘free_next’ defined but not used Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19Bluetooth: btmrvl: Do not send vendor events to bluetooth stackAndrei Emeltchenko
Vendor-specific events shall be processed in driver and not sent to bluetooth stack where they screw up HCI command countings. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-18ipv6: Move ipv6 proc file registration to end of init orderThomas Graf
/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc handler is installed in ip6_route_net_init() whereas fib_table_hash is allocated in fib6_net_init() _after_ the proc handler has been installed. This opens up a short time frame to access fib_table_hash with its pants down. Move the registration of the proc files to a later point in the init order to avoid the race. Tested :-) Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-18Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2012-06-17net: remove my future former mail addressRémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net> Cc: Sakari Ailus <sakari.ailus@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-17bonding: show all the link status of slavesAmerigo Wang
There are four link statuses of a bonding slave, the procfs code shows a wrong status when using downdelay/updelay: (slave->link == BOND_LINK_UP) ? "up" : "down" It doesn't respect the rest two statuses. This patch fixes it. Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-17usbnet: sanitise overlong driver information stringsPhil Sutter
As seen on smsc75xx, driver_info->description being longer than 32 characters messes up 'ethtool -i' output. Signed-off-by: Phil Sutter <phil.sutter@viprinet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-17be2net: Increase statistics structure size for skyhawk.Vasundhara Volam
Increasing the hardware statistics structure to accomodate statistics for skyhawk. Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-17be2net: Modify error message to incorporate subsystemVasundhara Volam
Modify IOCTL error message to print subsystem also. Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-17be2net: reduce gso_max_size setting to account for ethernet header.Sarveshwar Bandi
The maximum size of packet that can be handled by controller including ethernet header is 65535. Reducing gso_max_size accordingly. Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-17ixgbe: Fix PHC loophole allowing misconfiguration of increment registerJacob Keller
This patch fixes a potential hole when configuring the cycle counter used to generate the nanosecond time clock. This clock is based off of the SYSTIME registers along with the TIMINCA registers. The TIMINCA register determines the increment to be added to the SYSTIME registers every DMA clock tick. This register needs to be reconfigured whenever the link-speed changes. However, the value calculated stays the same when link is down and when link is up. Misconfiguration can occur if the link status changes due to a reset, which causes the TIMINCA register to be reset. This reset puts the device in an unstable state where the SYSTIME registers stop incrementing and the PTP protocol does not function. The solution is to double check the TIMINCA value and always reset the value if the register is zero. This prevents a misconfiguration bug that halts the PHC. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-16bnx2x: fix link for BCM57711 with 84823 phyYuval Mintz
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-16bnx2x: fix I2C non-respondent issueYuval Mintz
When I2C is not responding it's usually due to a previous unexpected reset during I2C operation. We release it by powering down and up the SFP+ module. Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-16Revert "ipv6: Prevent access to uninitialized fib_table_hash via ↵David S. Miller
/proc/net/ipv6_route" This reverts commit 2a0c451ade8e1783c5d453948289e4a978d417c9. It causes crashes, because now ip6_null_entry is used before it is initialized. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-15ipv6: Prevent access to uninitialized fib_table_hash via /proc/net/ipv6_routeThomas Graf
/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc handler is installed in ip6_route_net_init() whereas fib_table_hash is allocated in fib6_net_init() _after_ the proc handler has been installed. This opens up a short time frame to access fib_table_hash with its pants down. fib6_init() as a whole can't be moved to an earlier position as it also registers the rtnetlink message handlers which should be registered at the end. Therefore split it into fib6_init() which is run early and fib6_init_late() to register the rtnetlink message handlers. Signed-off-by: Thomas Graf <tgraf@suug.ch> Reviewed-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-15qlcnic: off by one in qlcnic_init_pci_info()Dan Carpenter
The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements. We allocate it that way a few lines earlier in the function. So this test is off by one. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-15net: remove skb_orphan_try()Eric Dumazet
Orphaning skb in dev_hard_start_xmit() makes bonding behavior unfriendly for applications sending big UDP bursts : Once packets pass the bonding device and come to real device, they might hit a full qdisc and be dropped. Without orphaning, the sender is automatically throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming sk_sndbuf is not too big) We could try to defer the orphaning adding another test in dev_hard_start_xmit(), but all this seems of little gain, now that BQL tends to make packets more likely to be parked in Qdisc queues instead of NIC TX ring, in cases where performance matters. Reverts commits : fc6055a5ba31 net: Introduce skb_orphan_try() 87fd308cfc6b net: skb_tx_hash() fix relative to skb_orphan_try() and removes SKBTX_DRV_NEEDS_SK_REF flag Reported-and-bisected-by: Jean-Michel Hautbois <jhautbois@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-15bnx2x: fix panic when TX ring is fullEric Dumazet
There is a off by one error in the minimal number of BD in bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue. A full size GSO packet, with data included in skb->head really needs (MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split() This error triggers if BQL is disabled and heavy TCP transmit traffic occurs. bnx2x_tx_split() definitely can be called, remove a wrong comment. Reported-by: Tomas Hruby <thruby@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Yaniv Rosner <yanivr@broadcom.com> Cc: Merav Sicron <meravs@broadcom.com> Cc: Tom Herbert <therbert@google.com> Cc: Robert Evans <evansr@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-15can: c_can: precedence error in c_can_chip_config()Dan Carpenter
(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which is zero so the condition is never true. The intent here was to test that both flags were set. Cc: <stable@kernel.org> # 2.6.39+ Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-14Bluetooth: Fix sending HCI_Disconnect only when connectedVishal Agarwal
HCI_Disconnect should only be sent after connection is established. If connection is not yet established and HCI_Disconnect is called then disconnection complete will be received with a handle which does not exist and hence this event will be ignored. But as mgmt.c will not receive this event, its variable for pending command is not cleared.This will result in future Disconnect commands for that BD Address to be blocked with error busy. Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-14Merge git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds
Pull kvm fix from Marcelo Tosatti: "Fix a spurious warning on CPU offline path" * git://git.kernel.org/pub/scm/virt/kvm/kvm: x86: kvmclock: remove check_and_clear_guest_paused warning
2012-06-14Merge tag 'pinctrl-fixes-for-v3.5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pinctrl fixes from Linus Walleij: - section markup fixes - clk_prepare() fix to conform to the clk API - memory leaks - incorrect debug messages - bad errorpaths - typos * tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: pinctrl-mxs: set platform driver data to NULL at errpath and at unregister pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails pinctrl: pinctrl-imx: fix incorrect debug message of maps pinctrl: pinctrl-imx: free if of_get_parent fails to get the parent node pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP pinctrl: nomadik: fix up typo pinctrl: nomadik: add clk_prepare() call pinctrl: fix a minor harmless typo pinctrl: sirf: mark of_device_id match table as __devinitconst
2012-06-14Merge tag 'sound-3.5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: - Fix a regression of USB-audio PCM assignment since 3.4 - A few VGA-switcheroo-related fixes for proper HDMI audio enablement - Fixed the missing initializations of HD-audio verbs, which may have resulted in various breakage - Some driver-specific ASoC updates - A few fixes for the dynamic PCM code - The addition of pinctrl support for the i.MX audmux which didn't make it into -rc1 due to cross tree dependency issues - A few minor fixes in compress API codes * tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda - Don't forget to call init verbs added by fixup list ALSA: HDA: Pin fixup for Zotac Z68 motherboard ALSA: compress_core: cleanup pointers on stop ALSA: compress_core: don't wake up on pause ALSA: hda - Fix detection of Creative SoundCore3D controllers vga_switcheroo: Enable/disable audio clients at the right time ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo vga_switcheroo: Add a helper function to get the client state ALSA: usb-audio: Fix substream assignments ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub ASoC: wm2000: Always use a 4s timeout for the firmware ASoC: dapm: Fix input list to use source widgets ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE ASoC: wm8994: Apply volume updates with clocks enabled ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants ASoC: imx-audmux: add pinctrl support ASoC: dapm: Fix connected widget capture path query.
2012-06-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David S. Miller: This has the fix for the wireless issues I ran into the other week as well as: 1) Fix CAN c_can driver transmit handling resulting in BUG check triggers, from AnilKumar Ch. 2) Fix packet drop monitor sleeping in atomic context, from Eric Dumazet. 3) Fix mv643xx_eth driver build regression, from Andrew Lunn. 4) Inetpeer freeing needs an RCU grace period in order to avoid races during tree invalidation. From Eric Dumazet. 5) Fix endianness bugs in xt_HMARK netfilter module, from Hans Schillstrom. 6) Add proper module refcounting to l2tp_eth to avoid crash on module unload, from Eric Dumazet. 7) Fix truncation of neighbour entry dumps due to logic errors in neigh_dump_info() and friends, from Eric Dumazet. 8) The conversion of fib6_age() to dst_neigh_lookup() accidently reversed the logic of a flags test, fix from Thomas Graf. 9) Fix checksum configuration in newer sky2 chips, from Stephen Hemminger. 10) Revert BQL support in NIU driver, doesn't work. 11) l2tp_ip_sendmsg() illegally uses a route without a proper reference. From Eric Dumazet. 12) be2net driver references an SKB after it's potentially been freed, also from Eric Dumazet. 13) Fix RCU stalls in dummy net driver init. Also from Eric Dumazet. 14) lpc_eth has several bugs in it's transmit engine leading to packet leaks and improper queue wakes, from Eric Dumazet. 15) Apply short DMA workaround to more tg3 chips, from Matt Carlson. 16) Add tilegx network driver. 17) Bonding queue mapping for a packet can get corrupted, fix from Eric Dumazet. 18) Fix bug in netpoll_send_udp() SKB management that can leave garbage in the payload in certain situations. From Eric Dumazet. 19) bnx2x driver interprets chip RX checksum offload incorrectly in encapsulation situations. Fix from Eric Dumazet. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits) bnx2x: fix checksum validation netpoll: fix netpoll_send_udp() bugs bonding: Fix corrupted queue_mapping bonding:record primary when modify it via sysfs tilegx network driver: initial support tg3: Apply short DMA frag workaround to 5906 net: stmmac: Fix clock en-/disable calls lpc_eth: fix tx completion lpc_eth: add missing ndo_change_mtu() dummy: fix rcu_sched self-detected stalls net: Reorder initialization in ip_route_output to fix gcc warning virtio-net: fix a race on 32bit arches r8169: avoid NAPI scheduling delay. net: Make linux/tcp.h C++ friendly (trivial) netdev: fix drivers/net/phy/ kernel-doc warnings net/core: fix kernel-doc warnings be2net: fix a race in be_xmit() l2tp: fix a race in l2tp_ip_sendmsg() mac80211: add back channel change flag NFC: Fix possible NULL ptr deref when getting the name of a socket ...
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 02:05:49 +0000