Age | Commit message (Collapse) | Author |
|
pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
The only things prevent drivers/serial/pxa.c from being generic enough
are:
1. IER_UUE which can be safely replaced by UART_IER_UUE as defined in
serial_reg.h for PXA
2. __PREG() and FFUART/BTUART/STUART definitions to decide the UART
port name
And removed the un-necessary #include of <mach/...> and <asm/...> headers.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Let's handle GPIOs by banks, each bank covers up to 32 GPIOs with one set
of registers, and each set of registers start from different offsets.
GPLR GPDR GPSR GPCR GRER GFER GEDR
BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048
BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C
BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050
BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148
BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C
BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150
NOTE:
BANK 3 is only available on PXA27x and later processors.
BANK 4 and 5 are only available on PXA935
1. introduce GPIO_BANK(n) for the offset base of each bank
2. 'struct pxa_gpio_chip' is expanded to include IRQ edge and mask
setings, and saved register values as well, and is dynamically
allocated due to possible bank number ranging from 3 to 6
3. all accesses to GPIO registers are made through 'regbase' within
'pxa_gpio_chip', and register offset
4. introduce several inline functions to simplify the code a bit
5. change IRQ demux handler to base on gpio chips
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
This makes gpio.c fully independent of pxa-regs.h (except for the
virtual address of the registers).
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Looks like we have to live with pxa_gpio_mode() for a while, giving
its presence is actually making gpio.c not generic enough, let's
move it temporarily outside before it can be fully purged.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
This is part of the work making gpio.c generic enough, the changes
include:
1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)
2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
number for the muxed GPIOs
3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:
<mach/pxa25x.h> - for pxa25x based platforms
<mach/pxa27x.h> - for pxa27x based platforms
<mach/pxa300.h> - for pxa300 based platforms
<mach/pxa320.h> - for pxa320 based platforms
<mach/pxa930.h> - for pxa930 based platforms
NOTE:
1. one header one board file, they are not compatible (i.e. they have
conflicting definitions which won't compile if included together).
2. Unless strictly necessary, the following header files are considered
to be SoC files use _only_, and is not recommended to be included in
board code:
<mach/hardware.h>
<mach/pxa-regs.h>
<mach/pxa2xx-regs.h>
<mach/pxa3xx-regs.h>
<mach/mfp.h>
<mach/mfp-pxa2xx.h>
<mach/mfp-pxa25x.h>
<mach/mfp-pxa27x.h>
<mach/mfp-pxa3xx.h>
<mach/mfp-pxa300.h>
<mach/mfp-pxa320.h>
<mach/mfp-pxa930.h>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Default to the same behaviour as the shipped WinCE system.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
so they can be shared with gpio_vbus.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Fixes an off-by-one error.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
devel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel
|
|
Add m2p dma support to the ep93xx
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the clocks for ep93xx m2p dma engine.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
SCALE: add ice dcc support
Tested on the ixp425 with the ice PEEDI
Ack-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/plat-mxc/dma-mx1-mx2.c
|
|
We should not be modifying the scatterlist passed to us from the
driver code; doing so breaks assumptions made by the DMA API code,
and could cause problems if the driver retries a transfer using an
old scatterlist.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There's no point these being in a generic include file when they're
only used in arch/arm/mach-rpc/dma.c.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The AT91SAM20-EK has a WM8731 attached to it with MCLK supplied from
PCLK0 and the digital audio interface supplied by SSC0.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Code has never been in buildable state since initial
merge.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove the unneeded #include <mach/hardware.h>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds the platform_device and resource structures for the USB
ISP1761 chip, usable with the in-kernel isp1760 driver.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This driver adds the platform_device definitions to allow the use of
CompactFlash on the RealView PB11MPCore and PB-A8 platforms. Note that
the CompactFlash controller is expected to be initialised by the Boot
Monitor and support the True IDE mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This chip is on the I2C bus on the RealView and Versatile boards. The
patch adds the i2c_board_info definition for this device and registers
it with the I2C subsystem.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If dev->id is not -1, the platform code may use static bus numbering
rather than dynamic. The patch also changes the i2c_versatile_init to a
subsys_initcall rather than module_init to make sure it is initialised
before the I2C devices initialisation.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This includes a new defconfig for the Shark and some changes to
the mach-shark directory to avoid namespace pollution and to
switch the rtc to the newer driver.
Signed-off-by: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
driver.
Ensure that the LCD engine is correctly re-initialised
and the correct parameters passed ot s3c2410fb_init_registers.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Ensure __iomem attribute is __force 'd off in the minimal
__raw_writel() implementation.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch also makes the frame pointer default to y only if
!ARM_UNWIND. LOCKDEP no longer selects FRAME_POINTER if ARM_UNWIND is
enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is needed to allow or stop the unwinding at certain points in the
kernel like exception entries.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds ELF section parsing for the unwinding tables in loadable
modules together with the PREL31 relocation symbol resolving.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds the main functionality for parsing the stack unwinding
information generated by the ARM EABI toolchains. The unwinding
information consists of an index with a pair of words per function and a
table with unwinding instructions. For more information, see "Exception
Handling ABI for the ARM Architecture" at:
http://infocenter.arm.com/help/topic/com.arm.doc.subset.swdev.abi/index.html
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch changes the walk_stacktrace and its callers for easier
integration of stack unwinding. The arch/arm/kernel/stacktrace.h file is
also moved to arch/arm/include/asm/stacktrace.h.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch moves code around in the arch/arm/kernel/traps.c file for
easier integration of the stack unwinding support.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add W90P910 Evaluate Board NOR flash driver support,
The EV Board default support W19B320ABT7H of Winbond inc.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Delete the macros W90X900_RES and W90X900_DEVICE
I thought it will be better to define the structures
for each device directly.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The __cpu_up() function in arch/arm/kernel/smp.c sets the pmd entries
without flushing or cleaning them.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The VFPv3D16 is a VFPv3 CPU configuration where only 16 double registers
are present, as the VFPv2 configuration. This patch adds the
corresponding hwcap bits so that applications or debuggers have more
information about the supported features.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds ptrace support for setting and getting the VFP registers
using PTRACE_SETVFPREGS and PTRACE_GETVFPREGS. The user_vfp structure
defined in asm/user.h contains 32 double registers (to cover VFPv3 and
Neon hardware) and the FPSCR register.
Cc: Paul Brook <paul@codesourcery.com>
Cc: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for gpiolib, including debugfs output, to the AT91 family.
The at91_get/set_gpio_value calls still exist since they are used by the
atmel serial driver.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch adds support for the HTC Himalaya device. It includes hardware definitions and w100fb support.
Signed-off-by: Zbynek Michl <Zbynek.Michl@seznam.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds support for the AM300 platform driver which uses the
E-Ink broadsheetfb display driver.
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds support for the E-Ink Broadsheet display controller.
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch updates the list of devices activated at init
to also include the keyboard and touchscreen structs.
We also remove a non-needed #ifdef.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|