summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-09-22HID: 3m: Adjust major / minor axes to scaleHenrik Rydberg
By visual inspection, the reported touch_major and touch_minor axes are a factor of two too large. Presumably the device actually reports the width_major and width_minor, which are generally about a factor of two larger than the touches themselves. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21HID: 3m: Correct touchscreen emulationHenrik Rydberg
The current code sometimes misses to report the last BTN_TOUCH event when multiple fingers are lifted simultaneously. With the introduction of MT slots, the tracking id is available to determine the oldest active contact. Use this information to simplify and correct the touchscreen emulation logic. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Stéphane Chatty <chatty@enac.fr> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21HID: 3m: Convert to MT slotsHenrik Rydberg
The Microtouch controller is capable of doing finger tracking on up to 60 fingers. To reduce bandwidth and cpu usage, convert the driver to use the MT slots protocol. On Stephane's suggestion, also insert the additional copyright lines. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Stephane Chatty <chatty@enac.fr> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21HID: 3m: Output proper orientation rangeHenrik Rydberg
The range of orientation values for height/width devices should be [0, 1], but is currently set to [1, 1]. Having min == max also breaks uinput device setup. Fixed with this patch. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21HID: 3m: Adjust to sequential MT HID protocolHenrik Rydberg
The multitouch extensions to the HID protocol allows for contact data to be sent over several reports, which is also the case for the 3M M2256PW touchscreen. This patch modifies the logic to only synchronize the input layer when all contacts have been received. Consequentially, the full 60-finger capacity of the device is enabled. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Stephane Chatty <chatty@enac.fr> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-21HID: Add a hid quirk for input sync overrideHenrik Rydberg
As of lately, HID devices which send per-frame data split over several HID reports have started to emerge. This patch adds a quirk which allows the HID driver to take over the input layer synchronization, and hence the control of the frame boundary. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-14Merge ssh://master.kernel.org/home/hpa/tree/secLinus Torvalds
* ssh://master.kernel.org/home/hpa/tree/sec: x86-64, compat: Retruncate rax after ia32 syscall entry tracing x86-64, compat: Test %rax for the syscall number, not %eax compat: Make compat_alloc_user_space() incorporate the access_ok()
2010-09-14MN10300: Fix up the IRQ names for the on-chip serial portsDavid Howells
Fix up the IRQ names for the MN10300 on-chip serial ports in the driver as request_interrupt() no longer allows names containing slashes, giving a warning like the following if one is encountered: ------------[ cut here ]------------ WARNING: at fs/proc/generic.c:323 __xlate_proc_name+0x62/0x7c() name 'ttySM0/Rx' Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-09-14Merge git://git.infradead.org/mtd-2.6Linus Torvalds
* git://git.infradead.org/mtd-2.6: mtd: pxa3xx: fix build error when CONFIG_MTD_PARTITIONS is not defined mtd: mxc_nand: configure pages per block for v2 controller mtd: OneNAND: Fix loop hang when DMA error at Samsung SoCs mtd: OneNAND: Fix 2KiB pagesize handling at Samsung SoCs mtd: Blackfin NFC: fix invalid free in remove() mtd: Blackfin NFC: fix build error after nand_scan_ident() change mxc_nand: Do not do byte accesses to the NFC buffer.
2010-09-14Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: fix hiddev's use of usb_find_interface HID: fixup blacklist entry for Asus T91MT HID: add device ID for new Asus Multitouch Controller HID: add no-get quirk for eGalax touch controller HID: Add quirk for eGalax touch controler. HID: add support for another BTC Emprex remote control HID: Set Report ID properly for Output reports on the Control endpoint. HID: Kanvus Note A5 tablet needs HID_QUIRK_MULTI_INPUT HID: Add support for chicony multitouch screens.
2010-09-14Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6Linus Torvalds
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: SUNRPC: Fix the NFSv4 and RPCSEC_GSS Kconfig dependencies statfs() gives ESTALE error NFS: Fix a typo in nfs_sockaddr_match_ipaddr6 sunrpc: increase MAX_HASHTABLE_BITS to 14 gss:spkm3 miss returning error to caller when import security context gss:krb5 miss returning error to caller when import security context Remove incorrect do_vfs_lock message SUNRPC: cleanup state-machine ordering SUNRPC: Fix a race in rpc_info_open SUNRPC: Fix race corrupting rpc upcall Fix null dereference in call_allocate
2010-09-14aio: check for multiplication overflow in do_io_submitJeff Moyer
Tavis Ormandy pointed out that do_io_submit does not do proper bounds checking on the passed-in iocb array:        if (unlikely(nr < 0))                return -EINVAL;        if (unlikely(!access_ok(VERIFY_READ, iocbpp, (nr*sizeof(iocbpp)))))                return -EFAULT;                      ^^^^^^^^^^^^^^^^^^ The attached patch checks for overflow, and if it is detected, the number of iocbs submitted is scaled down to a number that will fit in the long.  This is an ok thing to do, as sys_io_submit is documented as returning the number of iocbs submitted, so callers should handle a return value of less than the 'nr' argument passed in. Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com> Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-09-14x86-64, compat: Retruncate rax after ia32 syscall entry tracingRoland McGrath
In commit d4d6715, we reopened an old hole for a 64-bit ptracer touching a 32-bit tracee in system call entry. A %rax value set via ptrace at the entry tracing stop gets used whole as a 32-bit syscall number, while we only check the low 32 bits for validity. Fix it by truncating %rax back to 32 bits after syscall_trace_enter, in addition to testing the full 64 bits as has already been added. Reported-by: Ben Hawkes <hawkes@sota.gen.nz> Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2010-09-14x86-64, compat: Test %rax for the syscall number, not %eaxH. Peter Anvin
On 64 bits, we always, by necessity, jump through the system call table via %rax. For 32-bit system calls, in theory the system call number is stored in %eax, and the code was testing %eax for a valid system call number. At one point we loaded the stored value back from the stack to enforce zero-extension, but that was removed in checkin d4d67150165df8bf1cc05e532f6efca96f907cab. An actual 32-bit process will not be able to introduce a non-zero-extended number, but it can happen via ptrace. Instead of re-introducing the zero-extension, test what we are actually going to use, i.e. %rax. This only adds a handful of REX prefixes to the code. Reported-by: Ben Hawkes <hawkes@sota.gen.nz> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: <stable@kernel.org> Cc: Roland McGrath <roland@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org>
2010-09-14compat: Make compat_alloc_user_space() incorporate the access_ok()H. Peter Anvin
compat_alloc_user_space() expects the caller to independently call access_ok() to verify the returned area. A missing call could introduce problems on some architectures. This patch incorporates the access_ok() check into compat_alloc_user_space() and also adds a sanity check on the length. The existing compat_alloc_user_space() implementations are renamed arch_compat_alloc_user_space() and are used as part of the implementation of the new global function. This patch assumes NULL will cause __get_user()/__put_user() to either fail or access userspace on all architectures. This should be followed by checking the return value of compat_access_user_space() for NULL in the callers, at which time the access_ok() in the callers can also be removed. Reported-by: Ben Hawkes <hawkes@sota.gen.nz> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Chris Metcalf <cmetcalf@tilera.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Tony Luck <tony.luck@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: James Bottomley <jejb@parisc-linux.org> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: <stable@kernel.org>
2010-09-14HID: fix hiddev's use of usb_find_interfaceGuillaume Chazarain
My macbook infrared remote control was broken by commit bd25f4dd6972755579d0ea50d1a5ace2e9b00d1a ("HID: hiddev: use usb_find_interface, get rid of BKL"). This device appears in dmesg as: apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0 It stopped working as lircd was getting ENODEV when opening /dev/usb/hiddev0. AFAICS hiddev_driver is a dummy driver so usb_find_interface(&hiddev_driver) does not find anything. The device is associated with the usbhid driver, so let's do usb_find_interface(&hid_driver) instead. $ ls -l /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver lrwxrwxrwx 1 root root 0 2010-09-12 16:28 /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver -> ../../../../../../bus/usb/drivers/usbhid Signed-off-by: Guillaume Chazarain <guichaz@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-09-13Merge branch 'sched/urgent' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: sched: Improve latencies under load by decreasing minimum scheduling granularity
2010-09-13Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k,m68knommu: Wire up fanotify_init, fanotify_mark, and prlimit64
2010-09-13Merge branch 'release' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] fix siglock Quoth Tony: "I committed the fix for this last week prior to your -rc4 announcement reminding us to give proper "Reported-by:" credit. This one should have had: Reported-by: Tony Ernst <tee@sgi.com> and also Much-useful-investigation-and-tracing-by: Hedi Berriche <hedi@sgi.com> Much-useful-investigation-and-tracing-by: Petr Tesarik <ptesarik@novell.com>"
2010-09-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: cifs: prevent possible memory corruption in cifs_demultiplex_thread cifs: eliminate some more premature cifsd exits cifs: prevent cifsd from exiting prematurely [CIFS] ntlmv2/ntlmssp remove-unused-function CalcNTLMv2_partial_mac_key cifs: eliminate redundant xdev check in cifs_rename Revert "[CIFS] Fix ntlmv2 auth with ntlmssp" Revert "missing changes during ntlmv2/ntlmssp auth and sign" Revert "Eliminate sparse warning - bad constant expression" Revert "[CIFS] Eliminate unused variable warning"
2010-09-13Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: fs/9p: Don't use dotl version of mknod for dotu inode operations fs/9p: Use the correct dentry operations 9p: Check for NULL fid in v9fs_dir_release() fs/9p: Fix error handling in v9fs_get_sb fs/9p, net/9p: memory leak fixes
2010-09-13Merge branch 'for_linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6 * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: dquot: do full inode dirty in allocating space
2010-09-13Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6Linus Torvalds
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: spi/pl022: move probe call to subsys_initcall() powerpc/5200: mpc52xx_uart.c: Add of_node_put to avoid memory leak spi/pl022: fix APB pclk power regression on U300 spi/spi_s3c64xx: Warn if PIO transfers time out spi/s3c64xx: Fix incorrect reuse of 'val' local variable. spi/s3c64xx: Fix compilation warning spi/dw_spi: clean the cs_control code spi/dw_spi: Allow interrupt sharing spi/spi_s3c64xx: Increase dead reckoning time in wait_for_xfer() spi/spi_s3c64xx: Move to subsys_initcall() spi: free children in spi_unregister_master, not siblings gpiolib: Add 'struct gpio_chip' forward declaration for !GPIOLIB case of: Fix missing includes - ll_temac spi/spi_s3c64xx: Staticise non-exported functions spi/spi_s3c64xx: Make probe more robust against missing board config
2010-09-13m68k,m68knommu: Wire up fanotify_init, fanotify_mark, and prlimit64Geert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Greg Ungerer <gerg@uclinux.org>
2010-09-13sched: Improve latencies under load by decreasing minimum scheduling granularityIngo Molnar
Mathieu reported bad latencies with make -j10 kind of kbuild workloads - which is mostly caused by us scheduling with a too coarse granularity. Reduce the minimum granularity some more, to make sure we can meet the latency target. I got the following results (make -j10 kbuild load, average of 3 runs): vanilla: maximum latency: 38278.9 µs average latency: 7730.1 µs patched: maximum latency: 22702.1 µs average latency: 6684.8 µs Mathieu also measured it: | | * wakeup-latency.c (SIGEV_THREAD) with make -j10 | | - Mainline 2.6.35.2 kernel | | maximum latency: 45762.1 µs | average latency: 7348.6 µs | | - With only Peter's smaller min_gran (shown below): | | maximum latency: 29100.6 µs | average latency: 6684.1 µs | Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> LKML-Reference: <AANLkTi=8m4g01wZPacySoF7U0PevTNVgJoZZrHiUD-pN@mail.gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-13fs/9p: Don't use dotl version of mknod for dotu inode operationsAneesh Kumar K.V
We should not use dotlversion for the dotu inode operations Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2010-09-13fs/9p: Use the correct dentry operationsAneesh Kumar K.V
We should use the cached dentry operation only if caching mode is enabled Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2010-09-139p: Check for NULL fid in v9fs_dir_release()jvrao
NULL fid should be handled in cases where we endup calling v9fs_dir_release() before even we instantiate the fid in filp. Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2010-09-13fs/9p: Fix error handling in v9fs_get_sbAneesh Kumar K.V
This was introduced by 7cadb63d58a932041afa3f957d5cbb6ce69dcee5 Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2010-09-13fs/9p, net/9p: memory leak fixesLatchesar Ionkov
Four memory leak fixes in the 9P code. Signed-off-by: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2010-09-13mtd: pxa3xx: fix build error when CONFIG_MTD_PARTITIONS is not definedMark F. Brown
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-09-13mtd: mxc_nand: configure pages per block for v2 controllerSascha Hauer
This patch initializes the pages per block field in CONFIG1 for v2 controllers. It also sets the FP_INT field. This is the last field not correctly initialized, so we can switch from read/modify/write the CONFIG1 reg to just write the correct value. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: John Ogness <john.ogness@linutronix.de> Tested-by: John Ogness <john.ogness@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-09-13mtd: OneNAND: Fix loop hang when DMA error at Samsung SoCsKyungmin Park
When DMA error occurs. it's loop hang since it can't exit the loop. and it's the right DMA handling code as Spec. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-09-13mtd: OneNAND: Fix 2KiB pagesize handling at Samsung SoCsKyungmin Park
Wrong assumption bufferram can be switched between BufferRAM0 and BufferRAM1 Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-09-13mtd: Blackfin NFC: fix invalid free in remove()Mike Frysinger
Since info->mtd isn't dynamically allocated, we shouldn't attempt to kfree() it. Otherwise we get random fun corruption when unloading the driver built as a module. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-09-13mtd: Blackfin NFC: fix build error after nand_scan_ident() changeMike Frysinger
Seems some patches got out sync when being merged. The Blackfin NFC driver was updated to use nand_scan_ident(), but it missed the change where nand_scan_ident() now takes 3 arguments. So update this driver to fix build failures. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-09-12SUNRPC: Fix the NFSv4 and RPCSEC_GSS Kconfig dependenciesTrond Myklebust
The NFSv4 client's callback server calls svc_gss_principal(), which is defined in the auth_rpcgss.ko The NFSv4 server has the same dependency, and in addition calls svcauth_gss_flavor(), gss_mech_get_by_pseudoflavor(), gss_pseudoflavor_to_service() and gss_mech_put() from the same module. The module auth_rpcgss itself has no dependencies aside from sunrpc, so we only need to select RPCSEC_GSS. Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2010-09-12statfs() gives ESTALE errorMenyhart Zoltan
Hi, An NFS client executes a statfs("file", &buff) call. "file" exists / existed, the client has read / written it, but it has already closed it. user_path(pathname, &path) looks up "file" successfully in the directory-cache and restarts the aging timer of the directory-entry. Even if "file" has already been removed from the server, because the lookupcache=positive option I use, keeps the entries valid for a while. nfs_statfs() returns ESTALE if "file" has already been removed from the server. If the user application repeats the statfs("file", &buff) call, we are stuck: "file" remains young forever in the directory-cache. Signed-off-by: Zoltan Menyhart <Zoltan.Menyhart@bull.net> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: stable@kernel.org
2010-09-12NFS: Fix a typo in nfs_sockaddr_match_ipaddr6Trond Myklebust
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: stable@kernel.org
2010-09-12sunrpc: increase MAX_HASHTABLE_BITS to 14Miquel van Smoorenburg
The maximum size of the authcache is now set to 1024 (10 bits), but on our server we need at least 4096 (12 bits). Increase MAX_HASHTABLE_BITS to 14. This is a maximum of 16384 entries, each containing a pointer (8 bytes on x86_64). This is exactly the limit of kmalloc() (128K). Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2010-09-12gss:spkm3 miss returning error to caller when import security contextBian Naimeng
spkm3 miss returning error to up layer when import security context, it may be return ok though it has failed to import security context. Signed-off-by: Bian Naimeng <biannm@cn.fujitsu.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2010-09-12gss:krb5 miss returning error to caller when import security contextBian Naimeng
krb5 miss returning error to up layer when import security context, it may be return ok though it has failed to import security context. Signed-off-by: Bian Naimeng <biannm@cn.fujitsu.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2010-09-12Remove incorrect do_vfs_lock messageFabio Olive Leite
The do_vfs_lock function on fs/nfs/file.c is only called if NLM is not being used, via the -onolock mount option. Therefore it cannot really be "out of sync with lock manager" when the local locking function called returns an error, as there will be no corresponding call to the NLM. For details, simply check the if/else on do_setlk and do_unlk on fs/nfs/file.c. Signed-Off-By: Fabio Olive Leite <fleite@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2010-09-12SUNRPC: cleanup state-machine orderingJ. Bruce Fields
This is just a minor cleanup: net/sunrpc/clnt.c clarifies the rpc client state machine by commenting each state and by laying out the functions implementing each state in the order that each state is normally executed (in the absence of errors). The previous patch "Fix null dereference in call_allocate" changed the order of the states. Move the functions and update the comments to reflect the change. Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2010-09-12SUNRPC: Fix a race in rpc_info_openTrond Myklebust
There is a race between rpc_info_open and rpc_release_client() in that nothing stops a process from opening the file after the clnt->cl_kref goes to zero. Fix this by using atomic_inc_unless_zero()... Reported-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: stable@kernel.org
2010-09-12SUNRPC: Fix race corrupting rpc upcallTrond Myklebust
If rpc_queue_upcall() adds a new upcall to the rpci->pipe list just after rpc_pipe_release calls rpc_purge_list(), but before it calls gss_pipe_release (as rpci->ops->release_pipe(inode)), then the latter will free a message without deleting it from the rpci->pipe list. We will be left with a freed object on the rpc->pipe list. Most frequent symptoms are kernel crashes in rpc.gssd system calls on the pipe in question. Reported-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: stable@kernel.org
2010-09-12Fix null dereference in call_allocateJ. Bruce Fields
In call_allocate we need to reach the auth in order to factor au_cslack into the allocation. As of a17c2153d2e271b0cbacae9bed83b0eaa41db7e1 "SUNRPC: Move the bound cred to struct rpc_rqst", call_allocate attempts to do this by dereferencing tk_client->cl_auth, however this is not guaranteed to be defined--cl_auth can be zero in the case of gss context destruction (see rpc_free_auth). Reorder the client state machine to bind credentials before allocating, so that we can instead reach the auth through the cred. Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: stable@kernel.org
2010-09-12Linux 2.6.36-rc4Linus Torvalds
2010-09-11docbook: skip files with no docs since they generate scary warningsRandy Dunlap
Fix docbook templates that reference files that do not contain the expected kernel-doc notation. Fixes these warnings: Warning(arch/x86/include/asm/unaligned.h): no structured comments found Warning(lib/vsprintf.c): no structured comments found These cause errors in the generated html output, like below, so drop these lines. Name arch/x86/include/asm/unaligned.h - Document generation inconsistency Oops Warning The template for this document tried to insert the structured comment from the file arch/x86/include/asm/unaligned.h at this point, but none was found. This dummy section is inserted to allow generation to continue. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-09-11docbook: warn on unused doc entriesJohannes Berg
When you don't use !E or !I but only !F, then it's very easy to miss including some functions, structs etc. in documentation. To help finding which ones were missed, allow printing out the unused ones as warnings. For example, using this on mac80211 yields a lot of warnings like this: Warning: didn't use docs for DOC: mac80211 workqueue Warning: didn't use docs for ieee80211_max_queues Warning: didn't use docs for ieee80211_bss_change Warning: didn't use docs for ieee80211_bss_conf when generating the documentation for it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-23 15:00:45 +0000