| Age | Commit message (Collapse) | Author |
|---|
|
Subash Abhinov Kasiviswanathan says:
====================
net: qualcomm: rmnet: Enable csum offloads
This series introduces the MAPv4 packet format for checksum
offload plus some other minor changes.
Patches 1-3 are cleanups.
Patch 4 renames the ingress format to data format so that all data
formats can be configured using this going forward.
Patch 5 uses the pacing helper to improve TCP transmit performance.
Patch 6-9 defines the the MAPv4 for checksum offload for RX and TX.
A new header and trailer format are used as part of MAPv4.
For RX checksum offload, only the 1's complement of the IP payload
portion is computed by hardware. The meta data from RX header is
used to verify the checksum field in the packet. Note that the
IP packet and its field itself is not modified by hardware.
This gives metadata to help with the RX checksum. For TX, the
required metadata is filled up so hardware can compute the
checksum.
Patch 10 enables GSO on rmnet devices
v1->v2: Fix sparse errors reported by kbuild test robot
v2->v3: Update the commit message for Patch 5 based on Eric's comments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Real devices may support scatter gather(SG), so enable SG on rmnet
devices to use GSO. GSO reduces CPU cycles by 20% for a rate of
146Mpbs for a single stream TCP connection.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TX checksum offload applies to TCP / UDP packets which are not
fragmented using the MAPv4 checksum trailer. The following needs to be
done to have checksum computed in hardware -
1. Set the checksum start offset and inset offset.
2. Set the csum_enabled bit
3. Compute and set 1's complement of partial checksum field in
transport header.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the MAPv4 packet format in conjunction with MAP commands,
a dummy DL checksum trailer will be appended to the packet. Before
this packet is sent out as an ACK, the DL checksum trailer needs to be
removed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the MAPv4 packet format, receive checksum offload can be
enabled in hardware. The checksum computation over pseudo header is
not offloaded but the rest of the checksum computation over
the payload is offloaded. This applies only for TCP / UDP packets
which are not fragmented.
rmnet validates the TCP/UDP checksum for the packet using the checksum
from the checksum trailer added to the packet by hardware. The
validation performed is as following -
1. Perform 1's complement over the checksum value from the trailer
2. Compute 1's complement checksum over IPv4 / IPv6 header and
subtracts it from the value from step 1
3. Computes 1's complement checksum over IPv4 / IPv6 pseudo header and
adds it to the value from step 2
4. Subtracts the checksum value from the TCP / UDP header from the
value from step 3.
5. Compares the value from step 4 to the checksum value from the
TCP / UDP header.
6. If the comparison in step 5 succeeds, CHECKSUM_UNNECESSARY is set
and the packet is passed on to network stack. If there is a
failure, then the packet is passed on as such without modifying
the ip_summed field.
The checksum field is also checked for UDP checksum 0 as per RFC 768
and for unexpected TCP checksum of 0.
If checksum offload is disabled when using MAPv4 packet format in
receive path, the packet is queued as is to network stack without
the validations above.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAPv4 packet format adds support for RX / TX checksum offload.
For a bi-directional UDP stream at a rate of 570 / 146 Mbps, roughly
10% CPU cycles are saved.
For receive path, there is a checksum trailer appended to the end of
the MAP packet. The valid field indicates if hardware has computed
the checksum. csum_start_offset indicates the offset from the start
of the IP header from which hardware has computed checksum.
csum_length is the number of bytes over which the checksum was
computed and the resulting value is csum_value.
In the transmit path, a header is appended between the end of the MAP
header and the start of the IP packet. csum_start_offset is the offset
in bytes from which hardware will compute the checksum if the
csum_enabled bit is set. udp_ip4_ind indicates if the checksum
value of 0 is valid or not. csum_insert_offset is the offset from the
csum_start_offset where hardware will insert the computed checksum.
The use of this additional packet format for checksum offload is
explained in subsequent patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The real device over which the rmnet devices are installed also
aggregate multiple IP packets and sends them as a single large
aggregate frame to the hardware. This causes degraded throughput
for TCP TX due to bufferbloat.
To overcome this problem, pacing shift value of 8 is set using the
sk_pacing_shift_update() helper. This value was determined based
on experiments with a single stream TCP TX using iperf for a
duration of 30s.
Pacing shift | Observed data rate (Mbps)
10 | 9
9 | 140
8 | 146 (Max link rate)
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is done so that we can use this field for both ingress and
egress flags.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rmnet_map_demultiplex() is only declared but not defined anywhere,
so remove it.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rmnet devices cannot have a mux id of 255. This is validated when
assigning the mux id to the rmnet devices. As a result, checking for
mux id 255 does not apply in egress path.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already check the headroom once in rmnet_map_egress_handler(),
so this is not needed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling acpi_wmi_init() at the subsys_initcall() level causes ordering
issues to appear on some systems and they are difficult to reproduce,
because there is no guaranteed ordering between subsys_initcall()
calls, so they may occur in different orders on different systems.
In particular, commit 86d9f48534e8 (mm/slab: fix kmemcg cache
creation delayed issue) exposed one of these issues where genl_init()
and acpi_wmi_init() are both called at the same initcall level, but
the former must run before the latter so as to avoid a NULL pointer
dereference.
For this reason, move the acpi_wmi_init() invocation to the
initcall_sync level which should still be early enough for things
to work correctly in the WMI land.
Link: https://marc.info/?t=151274596700002&r=1&w=2
Reported-by: Jonathan McDowell <noodles@earth.li>
Reported-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
ip_set_net_exit()
Patch "netfilter: ipset: use nfnl_mutex_is_locked" is added the real
mutex locking check, which revealed the missing locking in ip_set_net_exit().
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Reported-by: syzbot+36b06f219f2439fe62e1@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
matching
The matching of the counters was not taken into account, fixed.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Make use of the swap macro and remove unnecessary variables tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add new instruction for the nf_tables VM that allows us to specify what
flows are offloaded into a given flow table via name. This new
instruction creates the flow entry and adds it to the flow table.
Only established flows, ie. we have seen traffic in both directions, are
added to the flow table. You can still decide to offload entries at a
later stage via packet counting or checking the ct status in case you
want to offload assured conntracks.
This new extension depends on the conntrack subsystem.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds the IPv6 flow table type, that implements the datapath
flow table to forward IPv6 traffic.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds the IPv6 flow table type, that implements the datapath
flow table to forward IPv6 traffic.
This patch exports ip6_dst_mtu_forward() that is required to check for
mtu to pass up packets that need PMTUD handling to the classic
forwarding path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds the IPv4 flow table type, that implements the datapath
flow table to forward IPv4 traffic. Rationale is:
1) Look up for the packet in the flow table, from the ingress hook.
2) If there's a hit, decrement ttl and pass it on to the neighbour layer
for transmission.
3) If there's a miss, packet is passed up to the classic forwarding
path.
This patch also supports layer 3 source and destination NAT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch defines the API to interact with flow tables, this allows to
add, delete and lookup for entries in the flow table. This also adds the
generic garbage code that removes entries that have expired, ie. no
traffic has been seen for a while.
Users of the flow table infrastructure can delete entries via
flow_offload_dead(), which sets the dying bit, this signals the garbage
collector to release an entry from user context.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch introduces a netlink control plane to create, delete and dump
flow tables. Flow tables are identified by name, this name is used from
rules to refer to an specific flow table. Flow tables use the rhashtable
class and a generic garbage collector to remove expired entries.
This also adds the infrastructure to add different flow table types, so
we can add one for each layer 3 protocol family.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This new bit tells us that the conntrack entry is owned by the flow
table offload infrastructure.
# cat /proc/net/nf_conntrack
ipv4 2 tcp 6 src=10.141.10.2 dst=147.75.205.195 sport=36392 dport=443 src=147.75.205.195 dst=192.168.2.195 sport=443 dport=36392 [OFFLOAD] mark=0 zone=0 use=2
Note the [OFFLOAD] tag in the listing.
The timer of such conntrack entries look like stopped from userspace.
In practise, to make sure the conntrack entry does not go away, the
conntrack timer is periodically set to an arbitrary large value that
gets refreshed on every iteration from the garbage collector, so it
never expires- and they display no internal state in the case of TCP
flows. This allows us to save a bitcheck from the packet path via
nf_ct_is_expired().
Conntrack entries that have been offloaded to the flow table
infrastructure cannot be deleted/flushed via ctnetlink. The flow table
infrastructure is also responsible for releasing this conntrack entry.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This macro is unnecessary, it just hides details for one single caller.
nfnl_dereference() is just enough.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Users cannot forge malformed IPv4/IPv6 headers via raw sockets that they
can inject into the stack. Specifically, not for IPv4 since 55888dfb6ba7
("AF_RAW: Augment raw_send_hdrinc to expand skb to fit iphdr->ihl
(v2)"). IPv6 raw sockets also ensure that packets have a well-formed
IPv6 header available in the skbuff.
At quick glance, br_netfilter also validates layer 3 headers and it
drops malformed both IPv4 and IPv6 packets.
Therefore, let's remove this defensive check all over the place.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
replacement for iptables "-m policy --dir in --policy {ipsec,none}".
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This abstraction has no clients anymore, remove it.
This is what remains from previous authors, so correct copyright
statement after recent modifications and code removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This is only needed by nf_queue, place this code where it belongs.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We cannot make a direct call to nf_ip6_reroute() because that would result
in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define reroute indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We cannot make a direct call to nf_ip6_route() because that would result
in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define route indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This is only used by nf_queue.c and this function comes with no symbol
dependencies with IPv6, it just refers to structure layouts. Therefore,
we can replace it by a direct function call from where it belongs.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We cannot make a direct call to nf_ip6_checksum_partial() because that
would result in autoloading the 'ipv6' module because of symbol
dependencies. Therefore, define checksum_partial indirection in
nf_ipv6_ops where this really belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We cannot make a direct call to nf_ip6_checksum() because that would
result in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define checksum indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This allows to reuse xt_connlimit infrastructure from nf_tables.
The upcoming nf_tables frontend can just pass in an nftables register
as input key, this allows limiting by any nft-supported key, including
concatenations.
For xt_connlimit, pass in the zone and the ip/ipv6 address.
With help from Yi-Hung Wei.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
They don't belong to the family definition, move them to the filter
chain type definition instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since NFPROTO_INET is handled from the core, we don't need to maintain
extra infrastructure in nf_tables to handle the double hook
registration, one for IPv4 and another for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use new native NFPROTO_INET support in netfilter core, this gets rid of
ad-hoc code in the nf_tables API codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Expand NFPROTO_INET in two hook registrations, one for NFPROTO_IPV4 and
another for NFPROTO_IPV6. Hence, we handle NFPROTO_INET from the core.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
So static_key_slow_dec applies to the family behind NFPROTO_INET.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Instead of passing struct nf_hook_ops, this is needed by follow up
patches to handle NFPROTO_INET from the core.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Just a cleanup, __nf_unregister_net_hook() is used by a follow up patch
when handling NFPROTO_INET as a real family from the core.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add helper function to test for the NFT_SET_ANONYMOUS flag.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Instead of calling this function from the family specific variant, this
reduces the code size in the fast path for the netdev, bridge and inet
families. After this change, we must call nft_set_pktinfo() upfront from
the chain hook indirection.
Before:
text data bss dec hex filename
2145 208 0 2353 931 net/netfilter/nf_tables_netdev.o
After:
text data bss dec hex filename
2125 208 0 2333 91d net/netfilter/nf_tables_netdev.o
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
46928a0b49f3 ("netfilter: nf_tables: remove multihook chains and
families") already removed this, this is a leftover.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
No problem for iptables as priorities are fixed values defined in the
nat modules, but in nftables the priority its coming from userspace.
Reject in case we see that such a hook would not work.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The netfilter NAT core cannot deal with more than one NAT hook per hook
location (prerouting, input ...), because the NAT hooks install a NAT null
binding in case the iptables nat table (iptable_nat hooks) or the
corresponding nftables chain (nft nat hooks) doesn't specify a nat
transformation.
Null bindings are needed to detect port collsisions between NAT-ed and
non-NAT-ed connections.
This causes nftables NAT rules to not work when iptable_nat module is
loaded, and vice versa because nat binding has already been attached
when the second nat hook is consulted.
The netfilter core is not really the correct location to handle this
(hooks are just hooks, the core has no notion of what kinds of side
effects a hook implements), but its the only place where we can check
for conflicts between both iptables hooks and nftables hooks without
adding dependencies.
So add nat annotation to hook_ops to describe those hooks that will
add NAT bindings and then make core reject if such a hook already exists.
The annotation fills a padding hole, in case further restrictions appar
we might change this to a 'u8 type' instead of bool.
iptables error if nft nat hook active:
iptables -t nat -A POSTROUTING -j MASQUERADE
iptables v1.4.21: can't initialize iptables table `nat': File exists
Perhaps iptables or your kernel needs to be upgraded.
nftables error if iptables nat table present:
nft -f /etc/nftables/ipv4-nat
/usr/etc/nftables/ipv4-nat:3:1-2: Error: Could not process rule: File exists
table nat {
^^
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
currently we always return -ENOENT to userspace if we can't find
a particular table, or if the table initialization fails.
Followup patch will make nat table init fail in case nftables already
registered a nat hook so this change makes xt_find_table_lock return
an ERR_PTR to return the errno value reported from the table init
function.
Add xt_request_find_table_lock as try_then_request_module replacement
and use it where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This can be same as NF_INET_NUMHOOKS if we don't support DECNET.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
no need to define hook points if the family isn't supported.
Because we need these hooks for either nftables, arp/ebtables
or the 'call-iptables' hack we have in the bridge layer add two
new dependencies, NETFILTER_FAMILY_{ARP,BRIDGE}, and have the
users select them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
no need to define hook points if the family isn't supported.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Not all families share the same hook count, adjust sizes to what is
needed.
struct net before:
/* size: 6592, cachelines: 103, members: 46 */
after:
/* size: 5952, cachelines: 93, members: 46 */
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
