Age | Commit message (Collapse) | Author |
|
When building very large kernels, the logic that emits replacement
sequences for alternatives fails when relative branches are present
in the code that is emitted into the .altinstr_replacement section
and patched in at the original site and fixed up. The reason is that
the linker will insert veneers if relative branches go out of range,
and due to the relative distance of the .altinstr_replacement from
the .text section where its branch targets usually live, veneers
may be emitted at the end of the .altinstr_replacement section, with
the relative branches in the sequence pointed at the veneers instead
of the actual target.
The alternatives patching logic will attempt to fix up the branch to
point to its original target, which will be the veneer in this case,
but given that the patch site is likely to be far away as well, it
will be out of range and so patching will fail. There are other cases
where these veneers are problematic, e.g., when the target of the
branch is in .text while the patch site is in .init.text, in which
case putting the replacement sequence inside .text may not help either.
So let's use subsections to emit the replacement code as closely as
possible to the patch site, to ensure that veneers are only likely to
be emitted if they are required at the patch site as well, in which
case they will be in range for the replacement sequence both before
and after it is transported to the patch site.
This will prevent alternative sequences in non-init code from being
released from memory after boot, but this is tolerable given that the
entire section is only 512 KB on an allyesconfig build (which weighs in
at 500+ MB for the entire Image). Also, note that modules today carry
the replacement sequences in non-init sections as well, and any of
those that target init code will be emitted into init sections after
this change.
This fixes an early crash when booting an allyesconfig kernel on a
system where any of the alternatives sequences containing relative
branches are activated at boot (e.g., ARM64_HAS_PAN on TX2)
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Dave P Martin <dave.martin@arm.com>
Link: https://lore.kernel.org/r/20200630081921.13443-1-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.8-2020-07-01:
amdgpu:
- Fix for vega20 boards without RAS support
- DC bandwidth revalidation fix
- Fix Renoir vram info fetching
- Fix hwmon freq printing
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701194415.4065-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.8-rc4:
- GVT fixes
- Include asm sources for render cache clear batches
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87imf7l6ee.fsf@intel.com
|
|
The wait_event_... defines evaluate to long so we should not assign it an int as this may truncate
the value.
Reported-by: Marshall Midden <marshallmidden@gmail.com>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
When xfstest generic/035, we found the target file was deleted
if the rename return -EACESS.
In cifs_rename2, we unlink the positive target dentry if rename
failed with EACESS or EEXIST, even if the target dentry is positived
before rename. Then the existing file was deleted.
We should just delete the target file which created during the
rename.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
|
The flag from the primary tcon needs to be copied into the volume info
so that cifs_get_tcon will try to enable extensions on the per-user
tcon. At that point, since posix extensions must have already been
enabled on the superblock, don't try to needlessly adjust the mount
flags.
Fixes: ce558b0e17f8 ("smb3: Add posix create context for smb3.11 posix mounts")
Fixes: b326614ea215 ("smb3: allow "posix" mount option to enable new SMB311 protocol extensions")
Signed-off-by: Paul Aurich <paul@darkrain42.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
|
Fixes: ca567eb2b3f0 ("SMB3: Allow persistent handle timeout to be configurable on mount")
Signed-off-by: Paul Aurich <paul@darkrain42.org>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
|
Fixes: 3e7a02d47872 ("smb3: allow disabling requesting leases")
Signed-off-by: Paul Aurich <paul@darkrain42.org>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
|
Without this:
- persistent handles will only be enabled for per-user tcons if the
server advertises the 'Continuous Availabity' capability
- resilient handles would never be enabled for per-user tcons
Signed-off-by: Paul Aurich <paul@darkrain42.org>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
|
Ensure multiuser SMB3 mounts use encryption for all users' tcons if the
mount options are configured to require encryption. Without this, only
the primary tcon and IPC tcons are guaranteed to be encrypted. Per-user
tcons would only be encrypted if the server was configured to require
encryption.
Signed-off-by: Paul Aurich <paul@darkrain42.org>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
|
This is useful for distinguishing SMB sessions on a multiuser mount.
Signed-off-by: Paul Aurich <paul@darkrain42.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
|
The freescale.com domain is gone for quite some time.
Use the nxp.com domain instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200701005346.1008-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fix from Wei Liu:
"One patch from Joseph to make panic reporting contain more useful
information"
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: Change flag to write log level in panic msg to false
|
|
Large clock values may overflow and show up as negative.
Reported by prOMiNd on IRC.
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Renoir uses integrated_system_info table v12. The table
has the same layout as v11 with respect to this data. Just
reuse the existing code for v12 for stable.
Fixes incorrectly reported vram info in the driver output.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Two fixups
- It fixes wrong return value by returing proper error value instead of
fixed one.
- It fixes ref count leak in mic_pre_enable.
One cleanup
- It removes dev_err() call on platform_get_irq() failure because
platform_get_irq() call dev_err() itself on failure.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1593395988-4612-1-git-send-email-inki.dae@samsung.com
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
A few fixes, mostly fallout from the address space refactor and dpu
color processing.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGv0SSXArdYs=mOLqJPJdkvk8CpxaJGecqgbOGazQ2n5og@mail.gmail.com
|
|
[Why]
Changes that are fast don't require updating DLG parameters making
this call unnecessary. Considering this is an expensive call it should
not be done on every flip.
DML touches clocks, p-state support, DLG params and a few other DC
internal flags and these aren't expected during fast. A hang has been
reported with this change when called on every flip which suggests that
modifying these fields is not recommended behavior on fast updates.
[How]
Guard the validation to only happen if update type isn't FAST.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1191
Fixes: a24eaa5c51255b ("drm/amd/display: Revalidate bandwidth before commiting DC updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Else there will be memory leak if alloc_disk() fails.
Fixes: 6a27b656fc02 ("block: virtio-blk: support multi virt queues per virtio-blk device")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 6ae72bfa656e ("PCI: Unify pcie_find_root_port() and
pci_find_pcie_root_port()") broke acpi_pci_bridge_d3() because calling
pcie_find_root_port() on a Root Port returned NULL when it should return
the Root Port, which in turn broke power management of PCIe hierarchies.
Rework pcie_find_root_port() so it returns its argument when it is already
a Root Port.
[bhelgaas: test device only once, test for PCIe]
Fixes: 6ae72bfa656e ("PCI: Unify pcie_find_root_port() and pci_find_pcie_root_port()")
Link: https://lore.kernel.org/r/20200622161248.51099-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat
Pull exfat fixes from Namjae Jeon:
- Zero out unused characters of FileName field to avoid a complaint
from some fsck tool.
- Fix memory leak on error paths.
- Fix unnecessary VOL_DIRTY set when calling rmdir on non-empty
directory.
- Call sync_filesystem() for read-only remount (Fix generic/452 test in
xfstests)
- Add own fsync() to flush dirty metadata.
* tag 'exfat-for-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: flush dirty metadata in fsync
exfat: move setting VOL_DIRTY over exfat_remove_entries()
exfat: call sync_filesystem for read-only remount
exfat: add missing brelse() calls on error paths
exfat: Set the unused characters of FileName field to the value 0000h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem fixes from James Morris:
"Two simple fixes for v5.8:
- Fix hook iteration and default value for inode_copy_up_xattr
(KP Singh)
- Fix the key_permission LSM hook function type (Sami Tolvanen)"
* tag 'fixes-v5.8-rc3-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security: Fix hook iteration and default value for inode_copy_up_xattr
security: fix the key_permission LSM hook function type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity updates from Mimi Zohar:
"Include PCRs 8 & 9 in per TPM 2.0 bank boot_aggregate calculation.
Prior to Linux 5.8 the SHA1 "boot_aggregate" value was padded with 0's
and extended into the other TPM 2.0 banks.
Included in the Linux 5.8 open window, TPM 2.0 PCR bank specific
"boot_aggregate" values (PCRs 0 - 7) are calculated and extended into the TPM banks.
Distro releases are now shipping grub2 with TPM support, which extend
PCRs 8 & 9. I'd like for PCRs 8 & 9 to be included in the new
"boot_aggregate" calculations.
For backwards compatibility, if the hash is SHA1, these new PCRs are
not included in the boot aggregate"
* tag 'integrity-v5.8-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: extend boot_aggregate with kernel measurements
|
|
Since 5.7, we've been using task_work to trigger async running of
requests in the context of the original task. This generally works
great, but there's a case where if the task is currently blocked
in the kernel waiting on a condition to become true, it won't process
task_work. Even though the task is woken, it just checks whatever
condition it's waiting on, and goes back to sleep if it's still false.
This is a problem if that very condition only becomes true when that
task_work is run. An example of that is the task registering an eventfd
with io_uring, and it's now blocked waiting on an eventfd read. That
read could depend on a completion event, and that completion event
won't get trigged until task_work has been run.
Use the TWA_SIGNAL notification for task_work, so that we ensure that
the task always runs the work when queued.
Cc: stable@vger.kernel.org # v5.7
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
So that the target task will exit the wait_event_interruptible-like
loop and call task_work_run() asap.
The patch turns "bool notify" into 0,TWA_RESUME,TWA_SIGNAL enum, the
new TWA_SIGNAL flag implies signal_wake_up(). However, it needs to
avoid the race with recalc_sigpending(), so the patch also adds the
new JOBCTL_TASK_WORK bit included in JOBCTL_PENDING_MASK.
TODO: once this patch is merged we need to change all current users
of task_work_add(notify = true) to use TWA_RESUME.
Cc: stable@vger.kernel.org # v5.7
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Tiger Lake's new unique ACPI device ID for Fan is not valid
because of missing 'C' in the ID. Use correct fan device ID.
Fixes: c248dfe7e0ca ("ACPI: fan: Add Tiger Lake ACPI device ID")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Adjust the reg property to fix the following warning seen with
'make dt_binding_check':
Documentation/devicetree/bindings/thermal/ti,am654-thermal.example.dt.yaml: example-0: thermal@42050000:reg:0: [0, 1107623936, 0, 604] is too long
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200630122527.28640-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Remove the soc unit address to fix the following warnings seen with
'make dt_binding_check':
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dts:22.20-49.11: Warning (unit_address_vs_reg): /example-0/soc@0: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/thermal/thermal-zones.example.dts:23.20-50.11: Warning (unit_address_vs_reg): /example-0/soc@0: node has a unit name, but no reg or ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200630121804.27887-1-festevam@gmail.com
[robh: also fix thermal-zones.yaml example]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Pass the sysreg unit name to fix the following warning seen with
'make dt_binding_check':
Warning (unit_address_vs_reg): /example-0/sysreg: node has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200629215500.18037-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Remove the leading zeroes to fix the following warning seen with
'make dt_binding_check':
Documentation/devicetree/bindings/usb/aspeed,usb-vhub.example.dts:37.33-42.23: Warning (unit_address_format): /example-0/usb-vhub@1e6a0000/vhub-strings/string@0409: unit name should not have leading 0s
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200629214027.16768-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
There are two processed schema files:
- processed-schema-examples.yaml
Used for 'make dt_binding_check'. This is always a full schema.
- processed-schema.yaml
Used for 'make dtbs_check'. This may be a full schema, or a smaller
subset if DT_SCHEMA_FILES is given by a user.
If DT_SCHEMA_FILES is not specified, they are the same. You can copy
the former to the latter instead of running dt-mk-schema twice. This
saves the cpu time a lot when you do 'make dt_binding_check dtbs_check'
because building the full schema takes a couple of seconds.
If DT_SCHEMA_FILES is specified, processed-schema.yaml is generated
based on the specified yaml files.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20200625170434.635114-4-masahiroy@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Currently, processed-schema.yaml is always built, but it is actually
used only for 'make dtbs_check'.
'make dt_binding_check' uses processed-schema-example.yaml instead.
Build processed-schema.yaml only for 'make dtbs_check'.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20200625170434.635114-3-masahiroy@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
We are having more and more schema files.
Commit 8b6b80218b01 ("dt-bindings: Fix command line length limit
calling dt-mk-schema") fixed the 'Argument list too long' error of
the schema checks, but the same error happens while cleaning too.
'make clean' after 'make dt_binding_check' fails as follows:
$ make dt_binding_check
[ snip ]
$ make clean
make[2]: execvp: /bin/sh: Argument list too long
make[2]: *** [scripts/Makefile.clean:52: __clean] Error 127
make[1]: *** [scripts/Makefile.clean:66: Documentation/devicetree/bindings] Error 2
make: *** [Makefile:1763: _clean_Documentation] Error 2
'make dt_binding_check' generates so many .example.dts, .dt.yaml files,
which are passed to the 'rm' command when you run 'make clean'.
I added a small hack to use the 'find' command to clean up most of the
build artifacts before they are processed by scripts/Makefile.clean
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20200625170434.635114-2-masahiroy@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Fix unit address to match the first address specified in the reg
property of the node in example.
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Link: https://lore.kernel.org/r/20200625135158.5861-1-l4stpr0gr4m@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Since commit e69f5dc623f9 ("dt-bindings: serial: Convert 8250 to
json-schema"), the schema for "ns16550a" is checked.
'make dt_binding_check' emits the following warning:
uart@5,00200000: $nodename:0: 'uart@5,00200000' does not match '^serial(@[0-9a-f,]+)*$'
Rename the node to follow the pattern defined in
Documentation/devicetree/bindings/serial/serial.yaml
While I was here, I removed leading zeros from unit names.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200623113242.779241-1-yamada.masahiro@socionext.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Sync with upstream dtc primarily to pickup the I2C bus check fixes. The
interrupt_provider check is noisy, so turn it off for now.
This adds the following commits from upstream:
9d7888cbf19c dtc: Consider one-character strings as strings
8259d59f59de checks: Improve i2c reg property checking
fdabcf2980a4 checks: Remove warning for I2C_OWN_SLAVE_ADDRESS
2478b1652c8d libfdt: add extern "C" for C++
f68bfc2668b2 libfdt: trivial typo fix
7be250b4d059 libfdt: Correct condition for reordering blocks
81e0919a3e21 checks: Add interrupt provider test
85e5d839847a Makefile: when building libfdt only, do not add unneeded deps
b28464a550c5 Fix some potential unaligned accesses in dtc
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
In flush_delete_work, instead of flushing each individual pending
delayed work item, cancel and re-queue them for immediate execution.
The waiting isn't needed here because we're already waiting for all
queued work items to complete in gfs2_flush_delete_work. This makes the
code more efficient, but more importantly, it avoids sleeping during a
rhashtable walk, inside rcu_read_lock().
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Log flush operations (gfs2_log_flush()) can target a specific transaction.
But if the function encounters errors (e.g. io errors) and withdraws,
the transaction was only freed it if was queued to one of the ail lists.
If the withdraw occurred before the transaction was queued to the ail1
list, function ail_drain never freed it. The result was:
BUG gfs2_trans: Objects remaining in gfs2_trans on __kmem_cache_shutdown()
This patch makes log_flush() add the targeted transaction to the ail1
list so that function ail_drain() will find and free it properly.
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Callers expect gfs2_inode_lookup to return an inode pointer or ERR_PTR(error).
Commit b66648ad6dcf caused it to return NULL instead of ERR_PTR(-ESTALE) in
some cases. Fix that.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: b66648ad6dcf ("gfs2: Move inode generation number check into gfs2_inode_lookup")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
The HPD sense mechanism in Allwinner's old HDMI encoder hardware is more
or less an input-only GPIO. Other GPIO-based HPD implementations
directly return the current state, instead of polling for a specific
state and returning the other if that times out.
Remove the I/O polling from sun4i_hdmi_connector_detect() and directly
return a known state based on the current reading. This also gets rid
of excessive CPU usage by kworker as reported on Stack Exchange [1] and
Armbian forums [2].
[1] https://superuser.com/questions/1515001/debian-10-buster-on-cubietruck-with-bug-in-sun4i-drm-hdmi
[2] https://forum.armbian.com/topic/14282-headless-systems-and-sun4i_drm_hdmi-a10a20/
Fixes: 9c5681011a0c ("drm/sun4i: Add HDMI support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629060032.24134-1-wens@kernel.org
|
|
Fix the following sparse warning:
arch/arm64/xen/../../arm/xen/enlighten.c:244: warning: macro
"GRANT_TABLE_PHYSADDR" is not used [-Wunused-macros]
It is an isolated macro, and should be removed when its last user
was deleted in the following commit 3cf4095d7446 ("arm/xen: Use
xen_xlate_map_ballooned_pages to setup grant table")
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
|
|
It's better to use /bin/sh instead of /bin/bash in order to run the tests
in the BusyBox shell.
Fixes: 6ea3dfe1e073 ("selftests: add TPM 2.0 tests")
Cc: stable@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
'test -f' is suitable only for *regular* files. Use 'test -e' instead.
Cc: Nikita Sobolev <Nikita.Sobolev@synopsys.com>
Cc: linux-integrity@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Fixes: 5627f9cffee7 ("Kernel selftests: Add check if TPM devices are supported")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The reverted commit illegitly uses tpm2-tools. External dependencies are
absolutely forbidden from these tests. There is also the problem that
clearing is not necessarily wanted behavior if the test/target computer is
not used only solely for testing.
Fixes: a9920d3bad40 ("tpm: selftest: cleanup after unseal with wrong auth/policy test")
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: stable@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Make blk_ksm_destroy() use the kvfree_sensitive() function (which was
introduced in v5.8-rc1) instead of open-coding it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Even if that's only a warning, not including asm/cacheflush.h
leads to svc_flush_bvec() being empty allthough powerpc defines
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE.
CC net/sunrpc/svcsock.o
net/sunrpc/svcsock.c:227:5: warning: "ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE" is not defined [-Wundef]
#if ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE
^
Include linux/highmem.h so that asm/cacheflush.h will be included.
Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ca07eda33e01 ("SUNRPC: Refactor svc_recvfrom()")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
I don't understand this code well, but I'm seeing a warning about a
still-referenced inode on unmount, and every other similar filesystem
does a dput() here.
Fixes: e8a79fb14f6b ("nfsd: add nfsd/clients directory")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
We don't drop the reference on the nfsdfs filesystem with
mntput(nn->nfsd_mnt) until nfsd_exit_net(), but that won't be called
until the nfsd module's unloaded, and we can't unload the module as long
as there's a reference on nfsdfs. So this prevents module unloading.
Fixes: 2c830dd7209b ("nfsd: persist nfsd filesystem across mounts")
Reported-and-Tested-by: Luo Xiaogang <lxgrxd@163.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A batch of fixes for the Freescale DSPI driver fixing some serious
issues with removal of active devices and one resume case, plus a few
new PCI IDs for Intel platforms"
* tag 'spi-fix-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Add support for Intel Tiger Lake PCH-H
spi: spi-fsl-dspi: Initialize completion before possible interrupt
spi: spi-fsl-dspi: Fix external abort on interrupt in resume or exit paths
spi: spi-fsl-dspi: Fix lockup if device is shutdown during SPI transfer
spi: spi-fsl-dspi: Fix lockup if device is removed during SPI transfer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixes from Daniel Lezcano:
- Fix undefined temperature if negative on the rcar_gen3 (Dien Pham)
- Fix wrong frequency converted from power for the cpufreq cooling
device (Finley Xiao)
- Fix compilation warnings by making functions static in the tsens
driver (Amit Kucheria)
- Fix return value of sprd_thm_probe for the Spreadtrum driver
(Tiezhu Yang)
- Fix bank number settings on the Mediatek mt8183 (Michael Kao)
- Fix missing of_node_put() at probe time i.MX (Anson Huang)
* tag 'thermal-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal/drivers/rcar_gen3: Fix undefined temperature if negative
thermal/drivers/cpufreq_cooling: Fix wrong frequency converted from power
thermal/drivers/tsens: Fix compilation warnings by making functions static
thermal/drivers/sprd: Fix return value of sprd_thm_probe()
thermal/drivers/mediatek: Fix bank number settings on mt8183
thermal/drivers: imx: Fix missing of_node_put() at probe time
|