| Age | Commit message (Collapse) | Author |
|---|
|
Since commit 6ce0d2001692 ("ARM: dma: Use dma_pfn_offset for dma address translation"),
dma_to_pfn() already returns the PFN with the physical memory start offset
so we don't need to add it again.
This fixes USB mass storage lock-up problem on systems that can't do DMA
over the entire physical memory range (e.g.) Keystone 2 systems with 4GB RAM
can only do DMA over the first 2GB. [K2E-EVM].
What happens there is that without this patch SCSI layer sets a wrong
bounce buffer limit in scsi_calculate_bounce_limit() for the USB mass
storage device. dma_max_pfn() evaluates to 0x8fffff and bounce_limit
is set to 0x8fffff000 whereas maximum DMA'ble physical memory on Keystone 2
is 0x87fffffff. This results in non DMA'ble pages being given to the
USB controller and hence the lock-up.
NOTE: in the above case, USB-SCSI-device's dma_pfn_offset was showing as 0.
This should have really been 0x780000 as on K2e, LOWMEM_START is 0x80000000
and HIGHMEM_START is 0x800000000. DMA zone is 2GB so dma_max_pfn should be
0x87ffff. The incorrect dma_pfn_offset for the USB storage device is because
USB devices are not correctly inheriting the dma_pfn_offset from the
USB host controller. This will be fixed by a separate patch.
Fixes: 6ce0d2001692 ("ARM: dma: Use dma_pfn_offset for dma address translation")
Cc: stable@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Whilst MPIDR values themselves are less than 32 bits, it is still
perfectly valid for a DT to have #address-cells > 1 in the CPUs node,
resulting in the "reg" property having leading zero cell(s). In that
situation, the big-endian nature of the data conspires with the current
behaviour of only reading the first cell to cause the kernel to think
all CPUs have ID 0, and become resoundingly unhappy as a consequence.
Take the full property length into account when parsing CPUs so as to
be correct under any circumstances.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Need to provide a dummy smp_fill_in_cpu_possible_map.
Fixes: 9b2f753ec237 ("sparc64: Fix cpu_possible_mask if nr_cpus is set")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge fixes from Andrew Morton:
"4 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mem-hotplug: use nodes that contain memory as mask in new_node_page()
scripts/recordmcount.c: account for .softirqentry.text
dma-mapping.h: preserve unmap info for CONFIG_DMA_API_DEBUG
mm,ksm: fix endless looping in allocating memory when ksm enable
|
|
9bb627be47a5 ("mem-hotplug: don't clear the only node in new_node_page()")
prevents allocating from an empty nodemask, but as David points out, it is
still wrong. As node_online_map may include memoryless nodes, only
allocating from these nodes is meaningless.
This patch uses node_states[N_MEMORY] mask to prevent the above case.
Fixes: 9bb627be47a5 ("mem-hotplug: don't clear the only node in new_node_page()")
Fixes: 394e31d2ceb4 ("mem-hotplug: alloc new page from a nearest neighbor node when mem-offline")
Link: http://lkml.kernel.org/r/1474447117.28370.6.camel@TP420
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Suggested-by: David Rientjes <rientjes@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
be7635e7287e ("arch, ftrace: for KASAN put hard/soft IRQ entries into
separate sections") added .softirqentry.text section, but it was not added
to recordmcount. So functions in the section are untracable. Add the
section to scripts/recordmcount.c and scripts/recordmcount.pl.
Fixes: be7635e7287e ("arch, ftrace: for KASAN put hard/soft IRQ entries into separate sections")
Link: http://lkml.kernel.org/r/1474902626-73468-1-git-send-email-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Steve Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org> [4.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When CONFIG_DMA_API_DEBUG is enabled we need to preserve unmapping address
even if "unmap" is a no-op for our architecutre because we need
debug_dma_unmap_page() to correctly cleanup all of the debug bookkeeping.
Failing to do so results in a false positive warnings about previously
mapped areas never being unmapped.
Link: http://lkml.kernel.org/r/1474387125-3713-1-git-send-email-andrew.smirnov@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Cc: "Luis R. Rodriguez" <mcgrof@suse.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Geliang Tang <geliangtang@163.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I hit the following hung task when runing a OOM LTP test case with 4.1
kernel.
Call trace:
[<ffffffc000086a88>] __switch_to+0x74/0x8c
[<ffffffc000a1bae0>] __schedule+0x23c/0x7bc
[<ffffffc000a1c09c>] schedule+0x3c/0x94
[<ffffffc000a1eb84>] rwsem_down_write_failed+0x214/0x350
[<ffffffc000a1e32c>] down_write+0x64/0x80
[<ffffffc00021f794>] __ksm_exit+0x90/0x19c
[<ffffffc0000be650>] mmput+0x118/0x11c
[<ffffffc0000c3ec4>] do_exit+0x2dc/0xa74
[<ffffffc0000c46f8>] do_group_exit+0x4c/0xe4
[<ffffffc0000d0f34>] get_signal+0x444/0x5e0
[<ffffffc000089fcc>] do_signal+0x1d8/0x450
[<ffffffc00008a35c>] do_notify_resume+0x70/0x78
The oom victim cannot terminate because it needs to take mmap_sem for
write while the lock is held by ksmd for read which loops in the page
allocator
ksm_do_scan
scan_get_next_rmap_item
down_read
get_next_rmap_item
alloc_rmap_item #ksmd will loop permanently.
There is no way forward because the oom victim cannot release any memory
in 4.1 based kernel. Since 4.6 we have the oom reaper which would solve
this problem because it would release the memory asynchronously.
Nevertheless we can relax alloc_rmap_item requirements and use
__GFP_NORETRY because the allocation failure is acceptable as ksm_do_scan
would just retry later after the lock got dropped.
Such a patch would be also easy to backport to older stable kernels which
do not have oom_reaper.
While we are at it add GFP_NOWARN so the admin doesn't have to be alarmed
by the allocation failure.
Link: http://lkml.kernel.org/r/1474165570-44398-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Suggested-by: Hugh Dickins <hughd@google.com>
Suggested-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull late MTD fixes from Brian Norris:
"Another round of MTD fixes for v4.8
My apologies for sending this so late. I've been fairly absent as a
maintainer this cycle, but I did queue these up weeks ago. In the
meantime, Richard was able to handle some other fixes (thanks!) but
didn't pick these up.
On the bright side, these are very simple changes that should carry
little risk.
Summary:
- Davinci NAND: fix a long-standing bug in how we clear/prep 4-bit ECC
- OMAP NAND: an error-handling fix that made it into v4.8-rc1 caused
error-handling cases in other configurations/code-paths; this fixes
the fix"
* tag 'for-linus-20160928' of git://git.infradead.org/linux-mtd:
mtd: nand: davinci: Reinitialize the HW ECC engine in 4bit hwctl
mtd: nand: omap2: Don't call dma_release_channel() if dma_request_chan() failed
|
|
I will be starting employment at Versity next week and would like to update
my MAINTAINERS e-mail to reflect that change. My versity e-mail is already
activated so I shouldn't get any bounces on the new one. My ability to help
with Ocfs2 kernel maintenance won't change as a result of the new job.
Signed-off-by: Mark Fasheh <mfasheh@versity.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, irq stack bootmem is allocated for all possible cpus
before nr_cpus value changes the list of possible cpus. As a result,
there is unnecessary wastage of bootmemory.
Move the irq stack bootmem allocation so that it happens after
possible cpu list is modified based on nr_cpus value.
Signed-off-by: Atish Patra <atish.patra@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If kernel boot parameter nr_cpus is set, it should define the number
of CPUs that can ever be available in the system i.e.
cpu_possible_mask. setup_nr_cpu_ids() overrides the nr_cpu_ids based
on the cpu_possible_mask during kernel initialization. If
cpu_possible_mask is not set based on the nr_cpus value, earlier part
of the kernel would be initialized using nr_cpus value leading to a
kernel crash.
Set cpu_possible_mask based on nr_cpus value. Thus setup_nr_cpu_ids()
becomes redundant and does not corrupt nr_cpu_ids value.
Signed-off-by: Atish Patra <atish.patra@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit af1b1a9b36b8 ("sparc64 mm: Fix base TSB sizing when hugetlb
pages are used") addressed the difference between hugetlb and THP
pages when computing TSB sizes. The following additional issues
were also discovered while working with the code.
In order to save memory, THP makes use of a huge zero page. This huge
zero page does not count against a task's RSS, but it does consume TSB
entries. This is similar to hugetlb pages. Therefore, count huge
zero page entries in hugetlb_pte_count.
Accounting of THP pages is done in the routine set_pmd_at().
Unfortunately, this does not catch the case where a THP page is split.
To handle this case, decrement the count in pmdp_invalidate().
pmdp_invalidate is only called when splitting a THP. However, 'sanity
checks' are added in case it is ever called for other purposes.
A more general issue exists with HPAGE_SIZE accounting.
hugetlb_pte_count tracks the number of HPAGE_SIZE (8M) pages. This
value is used to size the TSB for HPAGE_SIZE pages. However,
each HPAGE_SIZE page consists of two REAL_HPAGE_SIZE (4M) pages.
The TSB contains an entry for each REAL_HPAGE_SIZE page. Therefore,
the number of REAL_HPAGE_SIZE pages should be used to size the huge
page TSB. A new compile time constant REAL_HPAGE_PER_HPAGE is used
to multiply hugetlb_pte_count before sizing the TSB.
Changes from V1
- Fixed build issue if hugetlb or THP not configured
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To fix:
WARNING: vmlinux.o(.text.unlikely+0x580): Section mismatch in
reference from the function find_numa_latencies_for_group() to the
function .init.text:find_mlgroup()
The function find_numa_latencies_for_group() references the
function __init find_mlgroup(). This is often because
find_numa_latencies_for_group lacks a __init annotation or the
annotation of find_mlgroup is wrong.
It turns out find_numa_latencies_for_group is only called from:
static int __init numa_parse_mdesc(void)
and hence we can tag find_numa_latencies_for_group with __init.
In doing so we see that find_best_numa_node_for_mlgroup is only
called from within __init and hence can also be marked with __init.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Nitin Gupta <nitin.m.gupta@oracle.com>
Cc: Chris Hyser <chris.hyser@oracle.com>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The udl damage handler is supposed to render 'height' lines, but its
iterator has an obvious typo that makes it miss most lines if the
rectangle does not cover 0/0.
Fix the damage handler to correctly render all lines.
This is a fallout from:
commit e375882406d0cc24030746638592004755ed4ae0
Author: Noralf Trønnes <noralf@tronnes.org>
Date: Thu Apr 28 17:18:37 2016 +0200
drm/udl: Use drm_fb_helper deferred_io support
Tested-by: poma <poma@gmail.com>
Cc: stable@vger.kernel.org # 4.7+
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
nouveau: couple of fixes.
* 'linux-4.8' of git://github.com/skeggsb/linux:
drm/nouveau: Revert "bus: remove cpu_coherent flag"
drm/nouveau/fifo/nv04: avoid ramht race against cookie insertion
|
|
into drm-fixes
two amd fixes.
* 'drm-fixes-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/si/dpm: add workaround for for Jet parts
drm/amdgpu: disable CRTCs before teardown
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Three late fixes for cgroup: Two cpuset ones, one trivial and the
other pretty obscure, and a cgroup core fix for a bug which impacts
cgroup v2 namespace users"
* 'for-4.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix invalid controller enable rejections with cgroup namespace
cpuset: fix non static symbol warning
cpuset: handle race between CPU hotplug and cpuset_hotplug_work
|
|
Add clock quirks for Jet parts.
Reviewed-by: Sonny Jiang <sonny.jiang@amd.com>
Tested-by: Sonny Jiang <sonny.jiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some code called by drm_crtc_force_disable_all() wants to wait for all
fences, so only do fence teardown after CRTCs are disabled.
Fixes: 84b89bdcedf8 ("drm/amdgpu: Turn off CRTCs on driver unload")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Yotam Gigi says:
====================
Fix tc-ife bugs
This patch-set contains two bugfixes in the tc-ife action, one fixing some
random behaviour in encode side, and one fixing the decode side packet
parsing logic.
v2->v3
- Fix the encode side instead of the decode side
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On ife encode side, the action stores the different tlvs inside the ife
header, where each tlv length field should refer to the length of the
whole tlv (without additional padding) and not just the data length.
On ife decode side, the action iterates over the tlvs in the ife header
and parses them one by one, where in each iteration the current pointer is
advanced according to the tlv size.
Before, the encoding encoded only the data length inside the tlv, which led
to false parsing of ife the header. In addition, due to the fact that the
loop counter was unsigned, it could lead to infinite parsing loop.
This fix changes the loop counter to be signed and fixes the encoding to
take into account the tlv type and size.
Fixes: 28a10c426e81 ("net sched: fix encoding to use real length")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On ife encode side, external mac header is copied from the original packet
and may be overridden if the user requests. Before, the mac header copy
was done from memory region that might not be accessible anymore, as
skb_cow_head might free it and copy the packet. This led to random values
in the external mac header once the values were not set by user.
This fix takes the internal mac header from the packet, after the call to
skb_cow_head.
Fixes: ef6980b6becb ("net sched: introduce IFE action")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a pending socket is marked as rejected, we will decrease the
sk_ack_backlog twice. So don't decrement it for rejected sockets
in vsock_pending_work().
Testing of the rejected socket path was done through code
modifications.
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 62469c76007e ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c76007e we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c76007e, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Nelson says:
====================
net: fec: updates to align IP header
This patch series is the outcome of investigation into very high
numbers of alignment faults on kernel 4.1.33 from the linux-fslc
tree:
https://github.com/freescale/linux-fslc/tree/4.1-1.0.x-imx
The first two patches remove support for the receive accelerator (RACC) from
the i.MX25 and i.MX27 SoCs which don't support the function.
The third patch enables hardware alignment of the ethernet packet payload
(and especially the IP header) to prevent alignment faults in the IP stack.
Testing on i.MX6UL on the 4.1.33 kernel showed that this patch removed
on the order of 70k alignment faults during a 100MiB transfer using
wget.
Testing on an i.MX6Q (SABRE Lite) board on net-next (4.8.0-rc7) showed
a much more modest improvement from 10's of faults, and it's not clear
why that's the case.
====================
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.
Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:
~/$ cat /proc/cpu/alignment
User: 0
System: 72645 (inet_gro_receive+0x104/0x27c)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 72645
User faults: 3 (fixup+warn)
This patch was suggested by Andrew Lunn in this message to linux-netdev:
http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2
and adapted from a patch by Russell King from 2014:
http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8a
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation of joydev's input_device_id table recognizes only
devices with ABS_X, ABS_WHEEL or ABS_THROTTLE axes as joysticks.
There are joystick devices that do not have those axes, for example TRC
Rudder device. The device in question has ABS_Z, ABS_RX and ABS_RY axes
causing it not being detected as joystick.
This patch adds ABS_Z to the input_device_id list allowing devices with
ABS_Z axis to be detected correctly.
Signed-off-by: Ville Ranki <ville.ranki@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch avoids that the following memory leak is triggered if
use_blk_mq is disabled after a SCSI host has been allocated by the
ib_srp driver and before the same SCSI host is freed:
unreferenced object 0xffff8803a168c568 (size 256):
backtrace:
[<ffffffff81620c95>] kmemleak_alloc+0x45/0xa0
[<ffffffff811bb104>] __kmalloc_node+0x1e4/0x400
[<ffffffff81309fe4>] blk_mq_alloc_tag_set+0xb4/0x230
[<ffffffff814731b7>] scsi_mq_setup_tags+0xc7/0xd0
[<ffffffff81469c26>] scsi_add_host_with_dma+0x216/0x2d0
[<ffffffffa064bef5>] srp_create_target+0xe55/0x13d0 [ib_srp]
[<ffffffff8143ce23>] dev_attr_store+0x13/0x20
[<ffffffff8125f030>] sysfs_kf_write+0x40/0x50
[<ffffffff8125e397>] kernfs_fop_write+0x137/0x1c0
[<ffffffff811d8c13>] __vfs_write+0x23/0x140
[<ffffffff811d92e0>] vfs_write+0xb0/0x190
[<ffffffff811da5b4>] SyS_write+0x44/0xa0
[<ffffffff8162c8a5>] entry_SYSCALL_64_fastpath+0x18/0xa8
Fixes: 9aa9cc4221f5 ("scsi: remove the disable_blk_mq host flag")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since the commit below the ipmr/ip6mr rtnl_unicast() code uses the portid
instead of the previous dst_pid which was copied from in_skb's portid.
Since the skb is new the portid is 0 at that point so the packets are sent
to the kernel and we get scheduling while atomic or a deadlock (depending
on where it happens) by trying to acquire rtnl two times.
Also since this is RTM_GETROUTE, it can be triggered by a normal user.
Here's the sleeping while atomic trace:
[ 7858.212557] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
[ 7858.212748] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 7858.212881] 2 locks held by swapper/0/0:
[ 7858.213013] #0: (((&mrt->ipmr_expire_timer))){+.-...}, at: [<ffffffff810fbbf5>] call_timer_fn+0x5/0x350
[ 7858.213422] #1: (mfc_unres_lock){+.....}, at: [<ffffffff8161e005>] ipmr_expire_process+0x25/0x130
[ 7858.213807] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.0-rc7+ #179
[ 7858.213934] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 7858.214108] 0000000000000000 ffff88005b403c50 ffffffff813a7804 0000000000000000
[ 7858.214412] ffffffff81a1338e ffff88005b403c78 ffffffff810a4a72 ffffffff81a1338e
[ 7858.214716] 000000000000026c 0000000000000000 ffff88005b403ca8 ffffffff810a4b9f
[ 7858.215251] Call Trace:
[ 7858.215412] <IRQ> [<ffffffff813a7804>] dump_stack+0x85/0xc1
[ 7858.215662] [<ffffffff810a4a72>] ___might_sleep+0x192/0x250
[ 7858.215868] [<ffffffff810a4b9f>] __might_sleep+0x6f/0x100
[ 7858.216072] [<ffffffff8165bea3>] mutex_lock_nested+0x33/0x4d0
[ 7858.216279] [<ffffffff815a7a5f>] ? netlink_lookup+0x25f/0x460
[ 7858.216487] [<ffffffff8157474b>] rtnetlink_rcv+0x1b/0x40
[ 7858.216687] [<ffffffff815a9a0c>] netlink_unicast+0x19c/0x260
[ 7858.216900] [<ffffffff81573c70>] rtnl_unicast+0x20/0x30
[ 7858.217128] [<ffffffff8161cd39>] ipmr_destroy_unres+0xa9/0xf0
[ 7858.217351] [<ffffffff8161e06f>] ipmr_expire_process+0x8f/0x130
[ 7858.217581] [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180
[ 7858.217785] [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180
[ 7858.217990] [<ffffffff810fbc95>] call_timer_fn+0xa5/0x350
[ 7858.218192] [<ffffffff810fbbf5>] ? call_timer_fn+0x5/0x350
[ 7858.218415] [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180
[ 7858.218656] [<ffffffff810fde10>] run_timer_softirq+0x260/0x640
[ 7858.218865] [<ffffffff8166379b>] ? __do_softirq+0xbb/0x54f
[ 7858.219068] [<ffffffff816637c8>] __do_softirq+0xe8/0x54f
[ 7858.219269] [<ffffffff8107a948>] irq_exit+0xb8/0xc0
[ 7858.219463] [<ffffffff81663452>] smp_apic_timer_interrupt+0x42/0x50
[ 7858.219678] [<ffffffff816625bc>] apic_timer_interrupt+0x8c/0xa0
[ 7858.219897] <EOI> [<ffffffff81055f16>] ? native_safe_halt+0x6/0x10
[ 7858.220165] [<ffffffff810d64dd>] ? trace_hardirqs_on+0xd/0x10
[ 7858.220373] [<ffffffff810298e3>] default_idle+0x23/0x190
[ 7858.220574] [<ffffffff8102a20f>] arch_cpu_idle+0xf/0x20
[ 7858.220790] [<ffffffff810c9f8c>] default_idle_call+0x4c/0x60
[ 7858.221016] [<ffffffff810ca33b>] cpu_startup_entry+0x39b/0x4d0
[ 7858.221257] [<ffffffff8164f995>] rest_init+0x135/0x140
[ 7858.221469] [<ffffffff81f83014>] start_kernel+0x50e/0x51b
[ 7858.221670] [<ffffffff81f82120>] ? early_idt_handler_array+0x120/0x120
[ 7858.221894] [<ffffffff81f8243f>] x86_64_start_reservations+0x2a/0x2c
[ 7858.222113] [<ffffffff81f8257c>] x86_64_start_kernel+0x13b/0x14a
Fixes: 2942e9005056 ("[RTNETLINK]: Use rtnl_unicast() for rtnetlink unicasts")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracefs fixes from Steven Rostedt:
"Al Viro has been looking at the tracefs code, and has pointed out some
issues. This contains one fix by me and one by Al. I'm sure that
he'll come up with more but for now I tested these patches and they
don't appear to have any negative impact on tracing"
* tag 'trace-v4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
fix memory leaks in tracing_buffers_splice_read()
tracing: Move mutex to protect against resetting of seq data
|
|
When building XFS with -Werror, it now fails with:
include/linux/pagemap.h: In function 'fault_in_multipages_readable':
include/linux/pagemap.h:602:16: error: variable 'c' set but not used [-Werror=unused-but-set-variable]
volatile char c;
^
This is a regression caused by commit e23d4159b109 ("fix
fault_in_multipages_...() on architectures with no-op access_ok()").
Fix it by re-adding the "(void)c" trick taht was previously used to make
the compiler think the variable is used.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The NUMA balancing logic uses an arch-specific PROT_NONE page table flag
defined by pte_protnone() or pmd_protnone() to mark PTEs or huge page
PMDs respectively as requiring balancing upon a subsequent page fault.
User-defined PROT_NONE memory regions which also have this flag set will
not normally invoke the NUMA balancing code as do_page_fault() will send
a segfault to the process before handle_mm_fault() is even called.
However if access_remote_vm() is invoked to access a PROT_NONE region of
memory, handle_mm_fault() is called via faultin_page() and
__get_user_pages() without any access checks being performed, meaning
the NUMA balancing logic is incorrectly invoked on a non-NUMA memory
region.
A simple means of triggering this problem is to access PROT_NONE mmap'd
memory using /proc/self/mem which reliably results in the NUMA handling
functions being invoked when CONFIG_NUMA_BALANCING is set.
This issue was reported in bugzilla (issue 99101) which includes some
simple repro code.
There are BUG_ON() checks in do_numa_page() and do_huge_pmd_numa_page()
added at commit c0e7cad to avoid accidentally provoking strange
behaviour by attempting to apply NUMA balancing to pages that are in
fact PROT_NONE. The BUG_ON()'s are consistently triggered by the repro.
This patch moves the PROT_NONE check into mm/memory.c rather than
invoking BUG_ON() as faulting in these pages via faultin_page() is a
valid reason for reaching the NUMA check with the PROT_NONE page table
flag set and is therefore not always a bug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99101
Reported-by: Trevor Saunders <tbsaunde@tbsaunde.org>
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull MIPS fixes from Ralf Baechle:
"A round of 4.8 fixes:
MIPS generic code:
- Add a missing ".set pop" in an early commit
- Fix memory regions reaching top of physical
- MAAR: Fix address alignment
- vDSO: Fix Malta EVA mapping to vDSO page structs
- uprobes: fix incorrect uprobe brk handling
- uprobes: select HAVE_REGS_AND_STACK_ACCESS_API
- Avoid a BUG warning during PR_SET_FP_MODE prctl
- SMP: Fix possibility of deadlock when bringing CPUs online
- R6: Remove compact branch policy Kconfig entries
- Fix size calc when avoiding IPIs for small icache flushes
- Fix pre-r6 emulation FPU initialisation
- Fix delay slot emulation count in debugfs
ATH79:
- Fix test for error return of clk_register_fixed_factor.
Octeon:
- Fix kernel header to work for VDSO build.
- Fix initialization of platform device probing.
paravirt:
- Fix undefined reference to smp_bootstrap"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix delay slot emulation count in debugfs
MIPS: SMP: Fix possibility of deadlock when bringing CPUs online
MIPS: Fix pre-r6 emulation FPU initialisation
MIPS: vDSO: Fix Malta EVA mapping to vDSO page structs
MIPS: Select HAVE_REGS_AND_STACK_ACCESS_API
MIPS: Octeon: Fix platform bus probing
MIPS: Octeon: mangle-port: fix build failure with VDSO code
MIPS: Avoid a BUG warning during prctl(PR_SET_FP_MODE, ...)
MIPS: c-r4k: Fix size calc when avoiding IPIs for small icache flushes
MIPS: Add a missing ".set pop" in an early commit
MIPS: paravirt: Fix undefined reference to smp_bootstrap
MIPS: Remove compact branch policy Kconfig entries
MIPS: MAAR: Fix address alignment
MIPS: Fix memory regions reaching top of physical
MIPS: uprobes: fix incorrect uprobe brk handling
MIPS: ath79: Fix test for error return of clk_register_fixed_factor().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull one more powerpc fix from Michael Ellerman:
"powernv/pci: Fix m64 checks for SR-IOV and window alignment from
Russell Currey"
* tag 'powerpc-4.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv/pci: Fix m64 checks for SR-IOV and window alignment
|
|
The fixes to the radix tree test suite show that the multi-order case is
broken. The basic reason is that the radix tree code uses tagged
pointers with the "internal" bit in the low bits, and calculating the
pointer indices was supposed to mask off those bits. But gcc will
notice that we then use the index to re-create the pointer, and will
avoid doing the arithmetic and use the tagged pointer directly.
This cleans the code up, using the existing is_sibling_entry() helper to
validate the sibling pointer range (instead of open-coding it), and
using entry_to_node() to mask off the low tag bit from the pointer. And
once you do that, you might as well just use the now cleaned-up pointer
directly.
[ Side note: the multi-order code isn't actually ever used in the kernel
right now, and the only reason I didn't just delete all that code is
that Kirill Shutemov piped up and said:
"Well, my ext4-with-huge-pages patchset[1] uses multi-order entries.
It also converts shmem-with-huge-pages and hugetlb to them.
I'm okay with converting it to other mechanism, but I need
something. (I looked into Konstantin's RFC patchset[2]. It looks
okay, but I don't feel myself qualified to review it as I don't
know much about radix-tree internals.)"
[1] http://lkml.kernel.org/r/20160915115523.29737-1-kirill.shutemov@linux.intel.com
[2] http://lkml.kernel.org/r/147230727479.9957.1087787722571077339.stgit@zurg ]
Reported-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Cedric Blancher <cedric.blancher@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we replace a multiorder entry, check that all indices reflect the
new value.
Also, compile the test suite with -O2, which shows other problems with
the code due to some dodgy pointer operations in the radix tree code.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The iter->seq can be reset outside the protection of the mutex. So can
reading of user data. Move the mutex up to the beginning of the function.
Fixes: d7350c3f45694 ("tracing/core: make the read callbacks reentrants")
Cc: stable@vger.kernel.org # 2.6.30+
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Commit 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot
instructions") accidentally removed use of the MIPS_FPU_EMU_INC_STATS
macro from do_dsemulret, leading to the ds_emul file in debugfs always
returning zero even though we perform delay slot emulations.
Fix this by re-adding the use of the MIPS_FPU_EMU_INC_STATS macro.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14301/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch fixes the possibility of a deadlock when bringing up
secondary CPUs.
The deadlock occurs because the set_cpu_online() is called before
synchronise_count_slave(). This can cause a deadlock if the boot CPU,
having scheduled another thread, attempts to send an IPI to the
secondary CPU, which it sees has been marked online. The secondary is
blocked in synchronise_count_slave() waiting for the boot CPU to enter
synchronise_count_master(), but the boot cpu is blocked in
smp_call_function_many() waiting for the secondary to respond to it's
IPI request.
Fix this by marking the CPU online in cpu_callin_map and synchronising
counters before declaring the CPU online and calculating the maps for
IPIs.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reported-by: Justin Chen <justinpopo6@gmail.com>
Tested-by: Justin Chen <justinpopo6@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable@vger.kernel.org # v4.1+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Three fixlets for perf:
- add a missing NULL pointer check in the intel BTS driver
- make BTS an exclusive PMU because BTS can only handle one event at
a time
- ensure that exclusive events are limited to one PMU so that several
exclusive events can be scheduled on different PMU instances"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Limit matching exclusive events to one PMU
perf/x86/intel/bts: Make it an exclusive PMU
perf/x86/intel/bts: Make sure debug store is valid
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two smallish fixes:
- use the proper asm constraint in the Super-H atomic_fetch_ops
- a trivial typo fix in the Kconfig help text"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/hung_task: Fix typo in CONFIG_DETECT_HUNG_TASK help text
locking/atomic, arch/sh: Fix ATOMIC_FETCH_OP()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"Two fixes for EFI/PAT:
- a 32bit overflow bug in the PAT code which was unearthed by the
large EFI mappings
- prevent a boot hang on large systems when EFI mixed mode is enabled
but not used"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Only map RAM into EFI page tables if in mixed-mode
x86/mm/pat: Prevent hang during boot when mapping pages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Three fixes for irq core and irq chip drivers:
- Do not set the irq type if type is NONE. Fixes a boot regression
on various SoCs
- Use the proper cpu for setting up the GIC target list. Discovered
by the cpumask debugging code.
- A rather large fix for the MIPS-GIC so per cpu local interrupts
work again. This was discovered late because the code falls back
to slower timers which use normal device interrupts"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mips-gic: Fix local interrupts
irqchip/gicv3: Silence noisy DEBUG_PER_CPU_MAPS warning
genirq: Skip chained interrupt trigger setup if type is IRQ_TYPE_NONE
|
|
The definition of the flush hint table as:
void __iomem *flush_wpq[0][0];
...passed the unit test, but is broken as flush_wpq[0][1] and
flush_wpq[1][0] refer to the same entry. Fix this to use a helper that
calculates a slot in the table based on the geometry of flush hints in
the region. This is important to get right since virtualization
solutions use this mechanism to trigger hypervisor flushes to platform
persistence.
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
