| Age | Commit message (Collapse) | Author |
|---|
|
This patch moves the data allocated using dma_alloc_coherent to the
corresponding managed interface and does away with the calls to free the
allocated memory in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
this patch removes best_rate variable from can_calc_bittiming()
function which was set but was never used.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support of the device tree probing for the Renesas R-Car CAN controllers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Document the R-Car CAN device tree bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When writing the driver, I didn't give enough attention to the possible sources
of the CAN clock: although the value of the CLKR register was specified by the
platform data, the driver only handled one case, that is CAN clock being
sourced from the clkp1 clock, the same that clocks the whole CAN module. In
order to fix that overlook, we'll have to handle the CAN clock separately from
the peripheral clock (however, clkp1 will be specified for a CAN device only
once)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
For TX, only one dedicated tx buffer is used for sending data.
For RX, RXFIFO 0 is used for receiving data to avoid overflow.
Rx FIFO 1 and Rx Buffers are not used currently, as well as Tx Event FIFO.
Due to the message ram can be shared by multi m_can instances
and the fifo element is configurable which is SoC dependant,
the design is to parse the message ram related configuration data from device
tree rather than hardcode define it in driver which can make the message
ram sharing fully transparent to M_CAN controller driver,
then we can gain better driver maintainability and future features upgrade.
M_CAN also supports CANFD protocol features like data payload up to 64 bytes
and bitrate switch at runtime, however, this patch still does not add the
support for these features.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[mkl: Squahed semicolon cleanup by Fengguang Wu]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
add M_CAN device tree binding documentation
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Extend FlexCAN driver to support Vybrid. Vybrids variant of the IP
has ECC support which is controlled through the memory error
control register (MECR). There is also an errata which leads to
false positive error detections (ID e5295). This patch disables
the memory error detection completely.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
ecr register
The funcion flexcan_get_berr_counter() may be called from userspace even if the
interface is down, this the clocks are disabled. This patch switches on the
clocks before accessing the ecr register.
Reported-by: Ashutosh Singh <ashuleapyear@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are a couple of regression fixes, cpuidle menu governor
optimizations, fixes for ACPI proccessor and battery drivers,
hibernation fix to avoid problems related to the e820 memory map,
fixes for a few cpufreq drivers and a new version of the suspend
profiling tool analyze_suspend.py.
Specifics:
- Fix for an ACPI-based device hotplug regression introduced in 3.14
that causes a kernel panic to trigger when memory hot-remove is
attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen
- Fix for a cpufreq regression introduced in 3.16 that triggers a
"sleeping function called from invalid context" bug in
dev_pm_opp_init_cpufreq_table() from Stephen Boyd
- ACPI battery driver fix for a warning message added in 3.16 that
prints silly stuff sometimes from Mariusz Ceier
- Hibernation fix for safer handling of mismatches in the 820 memory
map between the configurations during image creation and during the
subsequent restore from Chun-Yi Lee
- ACPI processor driver fix to handle CPU hotplug notifications
correctly during system suspend/resume from Lan Tianyu
- Series of four cpuidle menu governor cleanups that also should
speed it up a bit from Mel Gorman
- Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus
Pargmann and Uwe Kleine-König
- Version 3.0 of the analyze_suspend.py suspend profiling tool from
Todd E Brandt"
* tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / battery: Fix warning message in acpi_battery_get_state()
PM / tools: analyze_suspend.py: update to v3.0
cpufreq: arm_big_little: fix module license spec
cpufreq: speedstep-smi: fix decimal printf specifiers
ACPI / hotplug: Check scan handlers in acpi_scan_hot_remove()
cpufreq: OPP: Avoid sleeping while atomic
cpufreq: cpu0: Do not print error message when deferring
cpufreq: integrator: Use set_cpus_allowed_ptr
PM / hibernate: avoid unsafe pages in e820 reserved regions
ACPI / processor: Make acpi_cpu_soft_notify() process CPU FROZEN events
cpuidle: menu: Lookup CPU runqueues less
cpuidle: menu: Call nr_iowait_cpu less times
cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
cpuidle: menu: Use shifts when calculating averages where possible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
|
|
Pull Sparc fixes from David Miller:
"Hook up the memfd syscall, and properly claim all PCI resources
discovered when building the PCI device tree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Hook up memfd_create system call.
sparc64: Properly claim resources as each PCI bus is probed.
sparc64: Skip bogus PCI bridge ranges.
sparc64: Expand PCI bridge probing debug logging.
|
|
Pull networking fixes from David Miller:
"I'm sending this out, in particular, to get the iwlwifi fix
propagated:
1) Fix build due to missing include in i40e driver, from Lucas
Tanure.
2) Memory leak in openvswitch port allocation, from Chirstoph Jaeger.
3) Check DMA mapping errors in myri10ge, from Stanislaw Gruszka.
4) Fix various deadlock scenerios in sunvnet driver, from Sowmini
Varadhan.
5) Fix cxgb4i build failures with incompatible Kconfig settings of
the driver vs ipv6, from Anish Bhatt.
6) Fix generation of ACK packet timestamps in the presence of TSO
which will be split up, from Willem de Bruijn.
7) Don't enable sched scan in iwlwifi driver, it causes firmware
crashes in some revisions. From Emmanuel Grumbach.
8) Revert a macvlan simplification that causes crashes.
9) Handle RTT calculations properly in the presence of repair'd SKBs,
from Andrey Vagin.
10) SIT tunnel lookup uses wrong device index in compares, from
Shmulik Ladkani.
11) Handle MTU reductions in TCP properly for ipv4 mapped ipv6
sockets, from Neal Cardwell.
12) Add missing annotations in rhashtable code, from Thomas Graf.
13) Fix false interpretation of two RTOs as being from the same TCP
loss event in the FRTO code, from Neal Cardwell"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netlink: Annotate RCU locking for seq_file walker
rhashtable: fix annotations for rht_for_each_entry_rcu()
rhashtable: unexport and make rht_obj() static
rhashtable: RCU annotations for next pointers
tcp: fix ssthresh and undo for consecutive short FRTO episodes
tcp: don't allow syn packets without timestamps to pass tcp_tw_recycle logic
tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
sit: Fix ipip6_tunnel_lookup device matching criteria
net: ethernet: ibm: ehea: Remove duplicate object from Makefile
net: xgene: Check negative return value of xgene_enet_get_ring_size()
tcp: don't use timestamp from repaired skb-s to calculate RTT (v2)
net: xilinx: Remove .owner field for driver
Revert "macvlan: simplify the structure port"
iwlwifi: mvm: disable scheduled scan to prevent firmware crash
xen-netback: remove loop waiting function
xen-netback: don't stop dealloc kthread too early
xen-netback: move NAPI add/remove calls
xen-netback: fix debugfs entry creation
xen-netback: fix debugfs write length check
net-timestamp: fix missing tcp fragmentation cases
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-08-14
Please pull this batch of fixes intended for the 3.17 stream...
Arend van Spriel brings two brcmfmac fixes, one which fixes a memory
leak and one which corrects some merge damage.
Emmanuel Grumbach fixes Linus's iwlwifi firmware-related log spam.
Rickard Strandqvist does some proper NULL termination after a call
to strncpy.
Ronald Wahl corrects a carl9170 problem with sending URBs with the
wrong endpoint type (resulting in log spam).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Silences the following sparse warnings:
net/netlink/af_netlink.c:2926:21: warning: context imbalance in 'netlink_seq_start' - wrong count at exit
net/netlink/af_netlink.c:2972:13: warning: context imbalance in 'netlink_seq_stop' - unexpected unlock
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call rcu_deference_raw() directly from within rht_for_each_entry_rcu()
as list_for_each_entry_rcu() does.
Fixes the following sparse warnings:
net/netlink/af_netlink.c:2906:25: expected struct rhash_head const *__mptr
net/netlink/af_netlink.c:2906:25: got struct rhash_head [noderef] <asn:4>*<noident>
Fixes: e341694e3eb57fc ("netlink: Convert netlink_lookup() to use RCU protected hash table")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to export rht_obj(), all inner to outer object translations
occur internally. It was intended to be used with rht_for_each() which
now primarily serves as the iterator for rhashtable_remove_pprev() to
effectively flush and free the full table.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Properly annotate next pointers as access is RCU protected in
the lookup path.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix TCP FRTO logic so that it always notices when snd_una advances,
indicating that any RTO after that point will be a new and distinct
loss episode.
Previously there was a very specific sequence that could cause FRTO to
fail to notice a new loss episode had started:
(1) RTO timer fires, enter FRTO and retransmit packet 1 in write queue
(2) receiver ACKs packet 1
(3) FRTO sends 2 more packets
(4) RTO timer fires again (should start a new loss episode)
The problem was in step (3) above, where tcp_process_loss() returned
early (in the spot marked "Step 2.b"), so that it never got to the
logic to clear icsk_retransmits. Thus icsk_retransmits stayed
non-zero. Thus in step (4) tcp_enter_loss() would see the non-zero
icsk_retransmits, decide that this RTO is not a new episode, and
decide not to cut ssthresh and remember the current cwnd and ssthresh
for undo.
There were two main consequences to the bug that we have
observed. First, ssthresh was not decreased in step (4). Second, when
there was a series of such FRTO (1-4) sequences that happened to be
followed by an FRTO undo, we would restore the cwnd and ssthresh from
before the entire series started (instead of the cwnd and ssthresh
from before the most recent RTO). This could result in cwnd and
ssthresh being restored to values much bigger than the proper values.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Fixes: e33099f96d99c ("tcp: implement RFC5682 F-RTO")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_tw_recycle heavily relies on tcp timestamps to build a per-host
ordering of incoming connections and teardowns without the need to
hold state on a specific quadruple for TCP_TIMEWAIT_LEN, but only for
the last measured RTO. To do so, we keep the last seen timestamp in a
per-host indexed data structure and verify if the incoming timestamp
in a connection request is strictly greater than the saved one during
last connection teardown. Thus we can verify later on that no old data
packets will be accepted by the new connection.
During moving a socket to time-wait state we already verify if timestamps
where seen on a connection. Only if that was the case we let the
time-wait socket expire after the RTO, otherwise normal TCP_TIMEWAIT_LEN
will be used. But we don't verify this on incoming SYN packets. If a
connection teardown was less than TCP_PAWS_MSL seconds in the past we
cannot guarantee to not accept data packets from an old connection if
no timestamps are present. We should drop this SYN packet. This patch
closes this loophole.
Please note, this patch does not make tcp_tw_recycle in any way more
usable but only adds another safety check:
Sporadic drops of SYN packets because of reordering in the network or
in the socket backlog queues can happen. Users behing NAT trying to
connect to a tcp_tw_recycle enabled server can get caught in blackholes
and their connection requests may regullary get dropped because hosts
behind an address translator don't have synchronized tcp timestamp clocks.
tcp_tw_recycle cannot work if peers don't have tcp timestamps enabled.
In general, use of tcp_tw_recycle is disadvised.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we use the correct address-family-specific function for
handling MTU reductions from within tcp_release_cb().
Previously AF_INET6 sockets were incorrectly always using the IPv6
code path when sometimes they were handling IPv4 traffic and thus had
an IPv4 dst.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Willem de Bruijn <willemb@google.com>
Fixes: 563d34d057862 ("tcp: dont drop MTU reduction indications")
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As of 4fddbf5d78 ("sit: strictly restrict incoming traffic to tunnel link device"),
when looking up a tunnel, tunnel's underlying interface (t->parms.link)
is verified to match incoming traffic's ingress device.
However the comparison was incorrectly based on skb->dev->iflink.
Instead, dev->ifindex should be used, which correctly represents the
interface from which the IP stack hands the ipip6 packets.
This allows setting up sit tunnels bound to vlan interfaces (otherwise
incoming ipip6 traffic on the vlan interface was dropped due to
ipip6_tunnel_lookup match failure).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the Makefile, ehea_phyp.o is included twice in the list of
object files compile into ehea.o.
This change removes one instance.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xgene_enet_get_ring_size() returns a negative value in case of an error,
but its only caller in xgene_enet_create_desc_ring() currently uses the
return value directly as u32. Instead, check for a negative value first and
error out in case. Also move the call to xgene_enet_get_ring_size() before
devm_kzalloc() so we don't need to free anything in the error path.
This fixes the following issue reported by the Coverity Scanner:
** CID 1231336: Improper use of negative value (NEGATIVE_RETURNS)
/drivers/net/ethernet/apm/xgene/xgene_enet_main.c: 596 in xgene_enet_create_desc_ring()
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't know right timestamp for repaired skb-s. Wrong RTT estimations
isn't good, because some congestion modules heavily depends on it.
This patch adds the TCPCB_REPAIRED flag, which is included in
TCPCB_RETRANS.
Thanks to Eric for the advice how to fix this issue.
This patch fixes the warning:
[ 879.562947] WARNING: CPU: 0 PID: 2825 at net/ipv4/tcp_input.c:3078 tcp_ack+0x11f5/0x1380()
[ 879.567253] CPU: 0 PID: 2825 Comm: socket-tcpbuf-l Not tainted 3.16.0-next-20140811 #1
[ 879.567829] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 879.568177] 0000000000000000 00000000c532680c ffff880039643d00 ffffffff817aa2d2
[ 879.568776] 0000000000000000 ffff880039643d38 ffffffff8109afbd ffff880039d6ba80
[ 879.569386] ffff88003a449800 000000002983d6bd 0000000000000000 000000002983d6bc
[ 879.569982] Call Trace:
[ 879.570264] [<ffffffff817aa2d2>] dump_stack+0x4d/0x66
[ 879.570599] [<ffffffff8109afbd>] warn_slowpath_common+0x7d/0xa0
[ 879.570935] [<ffffffff8109b0ea>] warn_slowpath_null+0x1a/0x20
[ 879.571292] [<ffffffff816d0a05>] tcp_ack+0x11f5/0x1380
[ 879.571614] [<ffffffff816d10bd>] tcp_rcv_established+0x1ed/0x710
[ 879.571958] [<ffffffff816dc9da>] tcp_v4_do_rcv+0x10a/0x370
[ 879.572315] [<ffffffff81657459>] release_sock+0x89/0x1d0
[ 879.572642] [<ffffffff816c81a0>] do_tcp_setsockopt.isra.36+0x120/0x860
[ 879.573000] [<ffffffff8110a52e>] ? rcu_read_lock_held+0x6e/0x80
[ 879.573352] [<ffffffff816c8912>] tcp_setsockopt+0x32/0x40
[ 879.573678] [<ffffffff81654ac4>] sock_common_setsockopt+0x14/0x20
[ 879.574031] [<ffffffff816537b0>] SyS_setsockopt+0x80/0xf0
[ 879.574393] [<ffffffff817b40a9>] system_call_fastpath+0x16/0x1b
[ 879.574730] ---[ end trace a17cbc38eb8c5c00 ]---
v2: moving setting of skb->when for repaired skb-s in tcp_write_xmit,
where it's set for other skb-s.
Fixes: 431a91242d8d ("tcp: timestamp SYN+DATA messages")
Fixes: 740b0f1841f6 ("tcp: switch rtt estimations to usec resolution")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a188a54d11629bef2169052297e61f3767ca8ce5.
It causes crashes
====================
[ 80.643286] BUG: unable to handle kernel NULL pointer dereference at 0000000000000878
[ 80.670103] IP: [<ffffffff810832e4>] try_to_grab_pending+0x64/0x1f0
[ 80.691289] PGD 22c102067 PUD 235bf0067 PMD 0
[ 80.706611] Oops: 0002 [#1] SMP
[ 80.717836] Modules linked in: macvlan nfsd lockd nfs_acl exportfs auth_rpcgss sunrpc oid_registry ioatdma ixgbe(-) mdio igb dca
[ 80.757935] CPU: 37 PID: 6724 Comm: rmmod Not tainted 3.16.0-net-next-08-12-2014-FCoE+ #1
[ 80.785688] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.0003.041920141333 04/19/2014
[ 80.820310] task: ffff880235a9eae0 ti: ffff88022e844000 task.ti: ffff88022e844000
[ 80.845770] RIP: 0010:[<ffffffff810832e4>] [<ffffffff810832e4>] try_to_grab_pending+0x64/0x1f0
[ 80.875326] RSP: 0018:ffff88022e847b28 EFLAGS: 00010046
[ 80.893251] RAX: 0000000000037a6a RBX: 0000000000000878 RCX: 0000000000000000
[ 80.917187] RDX: ffff880235a9eae0 RSI: 0000000000000001 RDI: ffffffff810832db
[ 80.941125] RBP: ffff88022e847b58 R08: 0000000000000000 R09: 0000000000000000
[ 80.965056] R10: 0000000000000001 R11: 0000000000000001 R12: ffff88022e847b70
[ 80.988994] R13: 0000000000000000 R14: ffff88022e847be8 R15: ffffffff81ebe440
[ 81.012929] FS: 00007fab90b07700(0000) GS:ffff88043f7a0000(0000) knlGS:0000000000000000
[ 81.040400] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 81.059757] CR2: 0000000000000878 CR3: 0000000235a42000 CR4: 00000000001407e0
[ 81.083689] Stack:
[ 81.090739] ffff880235a9eae0 0000000000000878 ffff88022e847b70 0000000000000000
[ 81.116253] ffff88022e847be8 ffffffff81ebe440 ffff88022e847b98 ffffffff810847f1
[ 81.141766] ffff88022e847b78 0000000000000286 ffff880234200000 0000000000000000
[ 81.167282] Call Trace:
[ 81.175768] [<ffffffff810847f1>] __cancel_work_timer+0x31/0x170
[ 81.195985] [<ffffffff8108494b>] cancel_work_sync+0xb/0x10
[ 81.214769] [<ffffffffa015ae68>] macvlan_port_destroy+0x28/0x60 [macvlan]
[ 81.237844] [<ffffffffa015b930>] macvlan_uninit+0x40/0x50 [macvlan]
[ 81.259209] [<ffffffff816bf6e2>] rollback_registered_many+0x1a2/0x2c0
[ 81.281140] [<ffffffff816bf81a>] unregister_netdevice_many+0x1a/0xb0
[ 81.302786] [<ffffffffa015a4ff>] macvlan_device_event+0x1ef/0x240 [macvlan]
[ 81.326439] [<ffffffff8108a13d>] notifier_call_chain+0x4d/0x70
[ 81.346366] [<ffffffff8108a201>] raw_notifier_call_chain+0x11/0x20
[ 81.367439] [<ffffffff816bf25b>] call_netdevice_notifiers_info+0x3b/0x70
[ 81.390228] [<ffffffff816bf2a1>] call_netdevice_notifiers+0x11/0x20
[ 81.411587] [<ffffffff816bf6bd>] rollback_registered_many+0x17d/0x2c0
[ 81.433518] [<ffffffff816bf925>] unregister_netdevice_queue+0x75/0x110
[ 81.455735] [<ffffffff816bfb2b>] unregister_netdev+0x1b/0x30
[ 81.475094] [<ffffffffa0039b50>] ixgbe_remove+0x170/0x1d0 [ixgbe]
[ 81.495886] [<ffffffff813512a2>] pci_device_remove+0x32/0x60
[ 81.515246] [<ffffffff814c75c4>] __device_release_driver+0x64/0xd0
[ 81.536321] [<ffffffff814c76f8>] driver_detach+0xc8/0xd0
[ 81.554530] [<ffffffff814c656e>] bus_remove_driver+0x4e/0xa0
[ 81.573888] [<ffffffff814c828b>] driver_unregister+0x2b/0x60
[ 81.593246] [<ffffffff8135143e>] pci_unregister_driver+0x1e/0xa0
[ 81.613749] [<ffffffffa005db18>] ixgbe_exit_module+0x1c/0x2e [ixgbe]
[ 81.635401] [<ffffffff810e738b>] SyS_delete_module+0x15b/0x1e0
[ 81.655334] [<ffffffff8187a395>] ? sysret_check+0x22/0x5d
[ 81.673833] [<ffffffff810abd2d>] ? trace_hardirqs_on_caller+0x11d/0x1e0
[ 81.696339] [<ffffffff8132bfde>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 81.717985] [<ffffffff8187a369>] system_call_fastpath+0x16/0x1b
[ 81.738199] Code: 00 48 83 3d 6e bb da 00 00 48 89 c2 0f 84 67 01 00 00 fa 66 0f 1f 44 00 00 49 89 14 24 e8 b5 4b 02 00 45 84 ed 0f 85 ac 00 00 00 <f0> 0f ba 2b 00 72 1d 31 c0 48 8b 5d d8 4c 8b 65 e0 4c 8b 6d e8
[ 81.807026] RIP [<ffffffff810832e4>] try_to_grab_pending+0x64/0x1f0
[ 81.828468] RSP <ffff88022e847b28>
[ 81.840384] CR2: 0000000000000878
[ 81.851731] ---[ end trace 9f6c7232e3464e11 ]---
====================
This bug could be triggered by these steps:
modprobe ixgbe ; modprobe macvlan
ip link add link p96p1 address 00:1B:21:6E:06:00 macvlan0 type macvlan
ip link add link p96p1 address 00:1B:21:6E:06:01 macvlan1 type macvlan
ip link add link p96p1 address 00:1B:21:6E:06:02 macvlan2 type macvlan
ip link add link p96p1 address 00:1B:21:6E:06:03 macvlan3 type macvlan
rmmod ixgbe
Reported-by: "Keller, Jacob E" <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild updates from Michal Marek:
"This is the non-critical part of kbuild for 3.17-rc1:
- make help hint to use make -s with make kernelrelease et al.
- moved a kbuild document to Documentation/kbuild where it belongs
- four new Coccinelle scripts, one dropped and one fixed
- new make kselftest target to run various tests on the kernel"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: kselftest - new make target to build and run kernel selftests
Coccinelle: Script to replace if and BUG with BUG_ON
Coccinelle: Script to detect incorrect argument to sizeof
Coccinelle: Script to use ARRAY_SIZE instead of division of two sizeofs
Coccinelle: Script to detect cast after memory allocation
coccinelle/null: solve parse error
Documentation: headers_install.txt is part of kbuild
kbuild: make -s should be used with kernelrelease/kernelversion/image_name
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- make clean also considers $(extra-m) and $(extra-) to be consistent
- cleanup and fixes in scripts/Makefile.host
- allow to override the name of the Python 2 executable with make
PYTHON=... (only needed for ia64 in practice)
- option to split debugingo into *.dwo files to save disk space if the
compiler supports it (CONFIG_DEBUG_INFO_SPLIT)
- option to use dwarf4 debuginfo if the compiler supports it
(CONFIG_DEBUG_INFO_DWARF4)
- fix for disabling certain warnings with clang
- fix for unneeded rebuild with dash when a command contains
backslashes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Fix handling of backslashes in *.cmd files
kbuild, LLVMLinux: Supress warnings unless W=1-3
Kbuild: Add a option to enable dwarf4 v2
kbuild: Support split debug info v4
kbuild: allow to override Python command name
kbuild: clean-up and bug fix of scripts/Makefile.host
kbuild: clean up scripts/Makefile.host
kbuild: drop shared library support from Makefile.host
kbuild: fix a bug of C++ host program handling
kbuild: fix a typo in scripts/Makefile.host
scripts/Makefile.clean: clean also $(extra-m) and $(extra-)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
|
|
Benjamin Herrenschmidt pointed out that I further missed modifying
update_vsyscall after the wall_to_mono value was changed to a
timespec64. This causes issues on powerpc32, which expects a 32bit
timespec.
This patch fixes the problem by properly converting from a timespec64 to
a timespec before passing the value on to the arch-specific vsyscall
logic.
[ Thomas is currently on vacation, but reviewed it and wanted me to send
this fix on to you directly. ]
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge leftovers from Andrew Morton:
"A few leftovers.
I have a bunch of OCFS2 patches which are still out for review and
which I might sneak along after -rc1. Partly my fault - I should send
my review pokes out earlier"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: fix CROSS_MEMORY_ATTACH help text grammar
drivers/mfd/rtsx_usb.c: export device table
mm, hugetlb_cgroup: align hugetlb cgroup limit to hugepage size
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtsx_usb driver contains the table for the devices it supports but
doesn't export it. As a result, no alias is generated and it doesn't
get loaded automatically.
Via https://bugzilla.novell.com/show_bug.cgi?id=890096
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Marcel Witte <wittemar@googlemail.com>
Cc: Roger Tseng <rogerable@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Memcg aligns memory.limit_in_bytes to PAGE_SIZE as part of the resource
counter since it makes no sense to allow a partial page to be charged.
As a result of the hugetlb cgroup using the resource counter, it is also
aligned to PAGE_SIZE but makes no sense unless aligned to the size of
the hugepage being limited.
Align hugetlb cgroup limit to hugepage size.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are firmwares which don't support scheduled scan.
Disable it for now.
Linus's system encoutered this issue.
Thanks to David Spinadel for his help.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull more powerpc updates from Ben Herrenschmidt:
"Here are some more powerpc bits for 3.17, essentially fixes.
The biggest series, also aimed at -stable, is from Aneesh and is the
result of weeks and weeks of debugging to find out why the heck or THP
implementation was occasionally triggering multi-hit errors in our
level 1 TLB. It ended up being a combination of issues including
subtleties as to how we should invalidate those special 'MPSS' pages
we use to allow the use of 16M pages inside 4K/64K "base page size"
segments (you really have to love our MMU !)
Another interesting one in the "OMG" category is the series from
Michael adding memory barriers to spin_is_locked(). That's also the
result of many days of debugging to figure out why the semaphore code
would occasionally crash in ways that made no sense. It ended up
being some creative lock stacking that was defeated by the fact that
our locks allow a load inside the locked section to be re-ordered with
the load of the lock value itself (I'm still of two mind about whether
to kill that once and for all by putting a heavier barrier back into
our lock implementation...). The fixes come with a long explanation
in the cset comments, feel free to read it if you feel like having a
headache today"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc/thp: Add tracepoints to track hugepage invalidate
powerpc/mm: Use read barrier when creating real_pte
powerpc/thp: Use ACCESS_ONCE when loading pmdp
powerpc/thp: Invalidate with vpn in loop
powerpc/thp: Handle combo pages in invalidate
powerpc/thp: Invalidate old 64K based hash page mapping before insert of 4k pte
powerpc/thp: Don't recompute vsid and ssize in loop on invalidate
powerpc/thp: Add write barrier after updating the valid bit
powerpc: reorder per-cpu NUMA information's initialization
powerpc/perf/hv-24x7: Use kmem_cache_free
powerpc/pseries/hvcserver: Fix endian issue in hvcs_get_partner_info
powerpc: Hard disable interrupts in xmon
powerpc: remove duplicate definition of TEXASR_FS
powerpc/pseries: Avoid deadlock on removing ddw
powerpc/pseries: Failure on removing device node
powerpc/boot: Use correct zlib types for comparison
powerpc/powernv: Interface to register/unregister opal dump region
printk: Add function to return log buffer address and size
powerpc: Add POWER8 features to CPU_FTRS_POSSIBLE/ALWAYS
powerpc/ppc476: Disable BTAC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock
Pull hwspinlock updates from Ohad Ben-Cohen:
"Two small hwspinlock changes for better OMAP support, coming from
Suman Anna"
* tag 'hwspinlock-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: enable OMAP build for AM33xx, AM43xx & DRA7xx
hwspinlock/omap: enable module before reading SYSSTATUS register
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull seccomp fix from James Morris.
BUG(!spin_is_locked()) really doesn't work very well in UP
configurations without any actual spinlock state. Which is very much
why we have that "assert_spin_lock()" function for this.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
seccomp: Replace BUG(!spin_is_locked()) with assert_spin_lock
|
|
'mlx4', 'mlx5', 'ocrdma' and 'srp' into for-next
|
|
In case of error, the function create_workqueue() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Several bug fixes in various drivers, plus a minor cleanup in the
tmp103 driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (tmp103) Remove duplicate test for I2C_FUNC_SMBUS_BYTE_DATA functionality
hwmon: (w83793) Fix vrm write operation
hwmon: (w83791d) Fix vrm write operation
hwmon: (w83627hf) Fix vrm write operation
hwmon: (vt1211) Fix vrm write operation
hwmon: (pc87360) Fix vrm write operation
hwmon: (lm87) Fix vrm write operation
hwmon: (asb100) Fix vrm write operation
hwmon: (adm1026) Fix vrm write operation
hwmon: (adm1025) Fix vrm write operation
hwmon: (hih6130) Fix missing hih6130->write_length setting
hwmon: (dme1737) Prevent overflow problem when writing large limits
hwmon: (emc6w201) Fix temperature limit range
hwmon: (ads1015) Fix out-of-bounds array access
hwmon: (lm92) Prevent overflow problem when writing large limits
|
|
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
|
|
Pull VFIO updates from Alex Williamson:
- enable support for bus reset on device release
- fixes for EEH support
* tag 'vfio-v3.17-rc1' of git://github.com/awilliam/linux-vfio:
drivers/vfio: Enable VFIO if EEH is not supported
drivers/vfio: Allow EEH to be built as module
drivers/vfio: Fix EEH build error
vfio-pci: Attempt bus/slot reset on release
vfio-pci: Use mutex around open, release, and remove
vfio-pci: Release devices with BusMaster disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from David Vrabel:
- fix ARM build
- fix boot crash with PVH guests
- improve reliability of resume/migration
* tag 'stable/for-linus-3.17-b-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: use vmap() to map grant table pages in PVH guests
x86/xen: resume timer irqs early
arm/xen: remove duplicate arch_gnttab_init() function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper changes from Mike Snitzer:
- Allow the thin target to paired with any size external origin; also
allow thin snapshots to be larger than the external origin.
- Add support for quickly loading a repetitive pattern into the
dm-switch target.
- Use per-bio data in the dm-crypt target instead of always using a
mempool for each allocation. Required switching to kmalloc alignment
for the bio slab.
- Fix DM core to properly stack the QUEUE_FLAG_NO_SG_MERGE flag
- Fix the dm-cache and dm-thin targets' export of the minimum_io_size
to match the data block size -- this fixes an issue where mkfs.xfs
would improperly infer raid striping was in place on the underlying
storage.
- Small cleanups in dm-io, dm-mpath and dm-cache
* tag 'dm-3.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm table: propagate QUEUE_FLAG_NO_SG_MERGE
dm switch: efficiently support repetitive patterns
dm switch: factor out switch_region_table_read
dm cache: set minimum_io_size to cache's data block size
dm thin: set minimum_io_size to pool's data block size
dm crypt: use per-bio data
block: use kmalloc alignment for bio slab
dm table: make dm_table_supports_discards static
dm cache metadata: use dm-space-map-metadata.h defined size limits
dm cache: fail migrations in the do_worker error path
dm cache: simplify deferred set reference count increments
dm thin: relax external origin size constraints
dm thin: switch to an atomic_t for tracking pending new block preparations
dm mpath: eliminate pg_ready() wrapper
dm io: simplify dec_count and sync_io
|
|
Pull MMC updates from Ulf Hansson:
"Me and Chris Ball decided to try out using my MMC tree as the primary
one, to simplify handling of patches.
This pull does thus contains all the MMC patches for 3.17 rc1, no pull
from Chris this time.
Details:
MMC core:
- forward compatibility for eMMC
- fix some blacklisted cards with broken secure discard
MMC host:
- mmci: Add support for Qualcomm variant
- mmci: Fix regression for arm_variant
- sdhci: Various fixes and cleanups
- sdhci: Improve external VDD regulator support
- sdhci: Support for DDR50 1.8V mode for BayTrail
- sdhci-st: Add driver for ST SDHCI controller
- sh-mmcif: DMA fixes
- omap_hsmmc: Add support for SDIO interrupts
- sdhci-pci: Add support for Intel Quark X1000
- dw_mmc: Update the reset sequence
- s3cmci: port DMA code to dmaengine API"
* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
mmc: mmci: Reverse IRQ handling for the arm_variant
mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
mmc: mmci: Remove redundant check of status for DATA irq
mmc: dw_mmc: change to use recommended reset procedure
mmc: sdhci-pxav3: Use devm_* managed helpers
mmc: tmio: Configure DMA slave bus width
mmc: sh_mmcif: Configure DMA slave bus width
mmc: sh_mmcif: Fix DMA slave address configuration
mmc: sh_mmcif: Document DT bindings
mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
mmc: Do not advertise secure discard if it is blacklisted
mmc: sdhci-msm: Get COMPILE_TEST support
mmc: sdhci-msm: Remove unnecessary header file inclusion
mmc: sdhci-msm: Fix the binding example
mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
mmc: sdhci: Preset value not supported in Baytrail eMMC
mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
mmc: MMC_SH_MMCIF should depend on HAS_DMA
...
|
|
Pull block driver changes from Jens Axboe:
"Nothing out of the ordinary here, this pull request contains:
- A big round of fixes for bcache from Kent Overstreet, Slava Pestov,
and Surbhi Palande. No new features, just a lot of fixes.
- The usual round of drbd updates from Andreas Gruenbacher, Lars
Ellenberg, and Philipp Reisner.
- virtio_blk was converted to blk-mq back in 3.13, but now Ming Lei
has taken it one step further and added support for actually using
more than one queue.
- Addition of an explicit SG_FLAG_Q_AT_HEAD for block/bsg, to
compliment the the default behavior of adding to the tail of the
queue. From Douglas Gilbert"
* 'for-3.17/drivers' of git://git.kernel.dk/linux-block: (86 commits)
bcache: Drop unneeded blk_sync_queue() calls
bcache: add mutex lock for bch_is_open
bcache: Correct printing of btree_gc_max_duration_ms
bcache: try to set b->parent properly
bcache: fix memory corruption in init error path
bcache: fix crash with incomplete cache set
bcache: Fix more early shutdown bugs
bcache: fix use-after-free in btree_gc_coalesce()
bcache: Fix an infinite loop in journal replay
bcache: fix crash in bcache_btree_node_alloc_fail tracepoint
bcache: bcache_write tracepoint was crashing
bcache: fix typo in bch_bkey_equal_header
bcache: Allocate bounce buffers with GFP_NOWAIT
bcache: Make sure to pass GFP_WAIT to mempool_alloc()
bcache: fix uninterruptible sleep in writeback thread
bcache: wait for buckets when allocating new btree root
bcache: fix crash on shutdown in passthrough mode
bcache: fix lockdep warnings on shutdown
bcache allocator: send discards with correct size
bcache: Fix to remove the rcu_sched stalls.
...
|
|
Pull block core bits from Jens Axboe:
"Small round this time, after the massive blk-mq dump for 3.16. This
pull request contains:
- Fixes for max_sectors overflow in ioctls from Akinoby Mita.
- Partition off-by-one bug fix in aix partitions from Dan Carpenter.
- Various small partition cleanups from Fabian Frederick.
- Fix for the block integrity code sometimes returning the wrong
vector count from Gu Zheng.
- Cleanup an re-org of the blk-mq queue enter/exit percpu counters
from Tejun. Dependent on the percpu pull for 3.17 (which was in
the block tree too), that you have already pulled in.
- A blkcg oops fix, also from Tejun"
* 'for-3.17/core' of git://git.kernel.dk/linux-block:
partitions: aix.c: off by one bug
blkcg: don't call into policy draining if root_blkg is already gone
Revert "bio: modify __bio_add_page() to accept pages that don't start a new segment"
bio: modify __bio_add_page() to accept pages that don't start a new segment
block: fix SG_[GS]ET_RESERVED_SIZE ioctl when max_sectors is huge
block: fix BLKSECTGET ioctl when max_sectors is greater than USHRT_MAX
block/partitions/efi.c: kerneldoc fixing
block/partitions/msdos.c: code clean-up
block/partitions/amiga.c: replace nolevel printk by pr_err
block/partitions/aix.c: replace count*size kzalloc by kcalloc
bio-integrity: add "bip_max_vcnt" into struct bio_integrity_payload
blk-mq: use percpu_ref for mq usage count
blk-mq: collapse __blk_mq_drain_queue() into blk_mq_freeze_queue()
blk-mq: decouble blk-mq freezing from generic bypassing
block, blk-mq: draining can't be skipped even if bypass_depth was non-zero
blk-mq: fix a memory ordering bug in blk_mq_queue_enter()
|
