| Age | Commit message (Collapse) | Author |
|---|
|
Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
USB devices do not require the chip test routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Using "iptables -L" with a lot of rules have a too big BH latency.
Jesper mentioned ~6 ms and worried of frame drops.
Switch to a per_cpu seqlock scheme, so that taking a snapshot of
counters doesnt need to block BH (for this cpu, but also other cpus).
This adds two increments on seqlock sequence per ipt_do_table() call,
its a reasonable cost for allowing "iptables -L" not block BH
processing.
Reported-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.
Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.
The previous version of this patch included a printk that was left over from
me fixing the filter setup. This patch does not include that printk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds a compressed input type for atr signature hash
computation. It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.
With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation. The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.
TCP_RR before:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23059.27
16384 87380
TCP_RR after:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23239.98
16384 87380
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the gigabit phys present on the CE4100 reference
platforms.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Phys supported by the driver do not remain powered off across a reset
of the device when the interface is down, e.g. on 82571, but not on 82574.
This patch powers down (only when WoL is disabled) the PHY after a reset if
the interface is down and the ethtool diagnostics are not currently running.
The ethtool diagnostic function required a minor re-factor as a result, and
the e1000_[get|put]_hw_control() functions are renamed since they are no
longer static to netdev.c as they are needed by the ethtool diagnostics.
A couple minor whitespace issues were cleaned up, too.
Reported-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the 82579 jumbo frame workaround, there is no need to re-write the CRC
calculation functionality already found in the kernel's ether_crc_le().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use string functions with bounds checking rather than their non-bounds
checking counterparts, and do not hard code these boundaries.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants. Fix
a couple whitespace issue with two already existing calls to e1e_wphy.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ICR register is clear on read and we don't care what the returned value
is when resetting the hardware so the icr variable(s) can be removed. We
should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and
from e1000_get_phy_id_82571() (dump a debug message when it fails and when
an unknown Phy id is returned).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to compute the features for other offloads (primarily
scatter/gather), we need to first check the ability of the NIC to
offload the checksum for the packet. Since we have already computed
this, we can directly use the result instead of figuring it out
again.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switches skb_need_linearize() to use the features that have
been centrally computed. In doing so, this fixes a problem where
scatter/gather should not be used because the card does not support
checksum offloading on that type of packet. On device registration
we only check that some form of checksum offloading is available if
scatter/gatther is enabled but we must also check at transmission
time. Examples of this include IPv6 or vlan packets on a NIC that
only supports IPv4 offloading.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switches dev_gso_segment() to use the device features computed
by the centralized routine. In doing so, it fixes a problem where
it would always use dev->features, instead of those appropriate
to the number of vlan tags if any are present.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that there is a single function that can compute the device
features relevant to a packet, we don't want to run it for each
offload. This converts netif_needs_gso() to take the features
of the device, rather than computing them itself.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_get_vlan_features() is currently only used by netif_needs_gso(),
so it only concerns itself with GSO features. However, several other
places also should take into account the contents of the packet when
deciding whether to offload to hardware. This generalizes the function
to return features about all of the various forms of offloading. Since
offloads tend to be linked together, this avoids duplicating the logic
in each location (i.e. the scatter/gather code also needs the checksum
logic).
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently only have software fallback for one type of checksum: the
TCP/UDP one's complement. This means that a protocol that uses hardware
offloading for a different type of checksum (FCoE, SCTP) must directly
check the device's features and do the right thing ahead of time. By
the time we get to dev_can_checksum(), we're only deciding whether to
apply the one algorithm in software or hardware. NETIF_F_HW_CSUM has the
same capabilities as the software version, so we should always use it if
present. The primary advantage of this is multiply tagged vlans can use
hardware checksumming.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It workarounds the 60s firmware load failure timeout for the
non-modular case.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix new kernel-doc notation warning in net/core/filter.c:
Warning(net/core/filter.c:172): No description found for parameter 'fentry'
Warning(net/core/filter.c:172): Excess function parameter 'filter' description in 'sk_run_filter'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix new kernel-doc notation warning in sock.h by annotating skc_dontcopy_*
as private fields.
Warning(include/net/sock.h:163): No description found for parameter 'skc_dontcopy_end[0]'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to NLM_F_DUMP is composed of two bits, NLM_F_ROOT | NLM_F_MATCH,
when doing "if (x & NLM_F_DUMP)", it tests for _either_ of the bits
being set. Because NLM_F_MATCH's value overlaps with NLM_F_EXCL,
non-dump requests with NLM_F_EXCL set are mistaken as dump requests.
Substitute the condition to test for _all_ bits being set.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The forcedeth driver uses the legacy PCI power management, so it has
to do PCI-specific things in its ->suspend() and ->resume() callbacks
and some of them are not done correctly.
Convert forcedeth to the new PCI power management framework and make
it let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Tested with nVidia Corporation MCP55 Ethernet (rev a2).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This converts sky2 to new VLAN offload flags control via ethtool.
It also allows for transmit offload of vlan tagged frames which
was not possible before.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sky2 driver would always try all possible supported speeds even
if the user only asked for a limited set of speed/duplex combinations.
Reported-by: Mohsen Hariri <m.hariri@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the race on bp->stats_pending between the timer and a LINK_UP event
handler.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move to D0 before clearing MSI/MSI-X configuration. Otherwise MSI/MSI-X
won't be cleared.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes in registers dump:
- Properly calculate dump length for 57712.
- Prevent HW blocks parity attentions when dumping registers in order to
prevent false parity errors handling.
- Update the bnx2x_dump.h file: old one had a few bugs that could cause
fatal HW error as a result of a registers dump.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't prevent RSS configuration in INT#x and MSI interrupt modes. Otherwise
Rx hash key won't be available.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ucode_init() and don't leak memory.
Failure to call release_firmware() will result in memory leak in
drivers/atm/ambassador.c::ucode_init().
This patch makes sure we always call release_firmware() when needed,
thus removing the leak(s).
Yes, I know checkpatch complains about this patch, but it was either that
or completely mess up the existing style, so I opted to use the existing
style and live with the checkpatch related flak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Failure to release_firmware() in drivers/net/hamradio/yam.c::add_mcs()
causes memory leak.
This patch should fix it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.
- The mx28 fec controller naming ENET-MAC is a different IP from FEC
used on other i.mx variants. But they are basically compatible
on software interface, so it's possible to share the same driver.
- ENET-MAC design on mx28 made an improper assumption that it runs
on a big-endian system. As the result, driver has to swap every
frame going to and coming from the controller.
- The external phys can only be configured by fec0, which means fec1
can not work independently and both phys need to be configured by
mii_bus attached on fec0.
- ENET-MAC reset will get mac address registers reset too.
- ENET-MAC MII/RMII mode and 10M/100M speed are configured
differently FEC.
- ETHER_EN bit must be set to get ENET-MAC interrupt work.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following commit made a fix to use fec_enet_open/fec_enet_close
over fec_enet_init/fec_stop for suspend/resume, because fec_enet_init
does not allow to have a working network interface at resume.
e3fe8558c7fc182972c3d947d88744482111f304
net/fec: fix pm to survive to suspend/resume
This fix works for i.mx/mxc fec controller, but fails on mx28 fec
which gets a different interrupt logic design. On i.mx fec, interrupt
can be triggered even bit ETHER_EN of ECR register is not set. But
on mx28 fec, ETHER_EN must be set to get interrupt work. Meanwhile,
MII interrupt is mandatory to resume the driver, because MDIO
read/write changed to interrupt mode by commit below.
97b72e4320a9aaa4a7f1592ee7d2da7e2c9bd349
fec: use interrupt for MDIO completion indication
fec_restart/fec_stop comes out as the solution working for both
cases.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mac field into fec_platform_data and consolidate function
fec_get_mac to get mac address in following order.
1) module parameter via kernel command line fec.macaddr=0x00,0x04,...
2) from flash in case of CONFIG_M5272 or fec_platform_data mac
field for others, which typically have mac stored in fuse
3) fec mac address registers set by bootloader
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "index" becomes legacy since fep->pdev->id starts working
to identify the instance.
Moreover, the call of fec_enet_init(ndev, 0) always passes 0
to fep->index. This makes the following code in fec_get_mac buggy.
/* Adjust MAC if using default MAC address */
if (iap == fec_mac_default)
dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
It may be the time to remove "index" and use fep->pdev->id instead.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in
a mdio write operation.
It's probably a typo introduced by commit:
e6b043d512fa8d9a3801bf5d72bfa3b8fc3b3cc8
netdev/fec.c: add phylib supporting to enable carrier detection (v2)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus:
hfsplus: %L-to-%ll, macro correction, and remove unneeded braces
hfsplus: spaces/indentation clean-up
hfsplus: C99 comments clean-up
hfsplus: over 80 character lines clean-up
hfsplus: fix an artifact in ioctl flag checking
hfsplus: flush disk caches in sync and fsync
hfsplus: optimize fsync
hfsplus: split up inode flags
hfsplus: write up fsync for directories
hfsplus: simplify fsync
hfsplus: avoid useless work in hfsplus_sync_fs
hfsplus: make sure sync writes out all metadata
hfsplus: use raw bio access for partition tables
hfsplus: use raw bio access for the volume headers
hfsplus: always use hfsplus_sync_fs to write the volume header
hfsplus: silence a few debug printks
hfsplus: fix option parsing during remount
Fix up conflicts due to VFS changes in fs/hfsplus/{hfsplus_fs.h,unicode.c}
|
|
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
|
|
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Constify function scope static struct sched_param usage
sched: Fix strncmp operation
sched: Move sched_autogroup_exit() to free_signal_struct()
sched: Fix struct autogroup memory leak
sched: Mark autogroup_init() __init
sched: Consolidate the name of root_task_group and init_task_group
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-apic-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: apic: Cleanup and simplify setup_local_APIC()
x86: Further simplify mp_irq info handling
x86: Unify 3 similar ways of saving mp_irqs info
x86, ioapic: Avoid writing io_apic id if already correct
x86, x2apic: Don't map lapic addr for preenabled x2apic systems
x86, sfi: Use register_lapic_address()
x86, apic: Use register_lapic_address() in init_apic_mapping()
x86, apic: Remove early_init_lapic_mapping()
x86, apic: Unify identical register_lapic_address() functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
* 'mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, MCE: Fix NB error formatting
EDAC, MCE: Use BIT_64() to eliminate warnings on 32-bit
EDAC, MCE: Enable MCE decoding on F15h
EDAC, MCE: Allow F15h bank 6 MCE injection
EDAC, MCE: Shorten error report formatting
EDAC, MCE: Overhaul error fields extraction macros
EDAC, MCE: Add F15h FP MCE decoder
EDAC, MCE: Add F15 EX MCE decoder
EDAC, MCE: Add an F15h NB MCE decoder
EDAC, MCE: No F15h LS MCE decoder
EDAC, MCE: Add F15h CU MCE decoder
EDAC, MCE: Add F15h IC MCE decoder
EDAC, MCE: Add F15h DC MCE decoder
EDAC, MCE: Select extended error code mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
* 'edac-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Disable DRAM ECC injection on K8
EDAC: Fixup scrubrate manipulation
amd64_edac: Remove two-stage initialization
amd64_edac: Check ECC capabilities initially
amd64_edac: Carve out ECC-related hw settings
amd64_edac: Remove PCI ECS enabling functions
amd64_edac: Remove explicit Kconfig PCI dependency
amd64_edac: Allocate driver instances dynamically
amd64_edac: Rework printk macros
amd64_edac: Rename CPU PCI devices
amd64_edac: Concentrate per-family init even more
amd64_edac: Cleanup the CPU PCI device reservation
amd64_edac: Simplify CPU family detection
amd64_edac: Add per-family init function
amd64_edac: Use cached extended CPU model
amd64_edac: Remove F11h support
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (65 commits)
[S390] prevent unneccesary loops_per_jiffy recalculation
[S390] cpuinfo: use get_online_cpus() instead of preempt_disable()
[S390] smp: remove cpu hotplug messages
[S390] mutex: enable spinning mutex on s390
[S390] mutex: Introduce arch_mutex_cpu_relax()
[S390] cio: fix ccwgroup unregistration race condition
[S390] perf: add DWARF register lookup for s390
[S390] cleanup ftrace backend functions
[S390] ptrace cleanup
[S390] smp/idle: call init_idle() before starting a new cpu
[S390] smp: delay idle task creation
[S390] dasd: Correct retry counter for terminated I/O.
[S390] dasd: Add support for raw ECKD access.
[S390] dasd: Prevent deadlock during suspend/resume.
[S390] dasd: Improve handling of stolen DASD reservation
[S390] dasd: do path verification for paths added at runtime
[S390] dasd: add High Performance FICON multitrack support
[S390] cio: reduce memory consumption of itcw structures
[S390] nmi: enable machine checks early
[S390] qeth: buffer count imbalance
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'rmobile-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (67 commits)
ARM: mach-shmobile: update for SMP changes.
ARM: mach-shmobile: update for GIC changes.
ARM: mach-shmobile: Fix up clkdev fallout for SH73A0.
dma: shdma: don't register the global die notifier multiple times
ARM: mach-shmobile: Rely on run-time IRQ handlers
ARM: mach-shmobile: Run-time IRQ handler for GIC
ARM: mach-shmobile: Run-time IRQ handler for INTCA
ARM: mach-shmobile: Enable CONFIG_MULTI_IRQ_HANDLER
ARM: mach-shmobile: Use shared GIC entry macros
ARM: mach-shmobile: mackerel: Add zboot support
ARM: mach-shmobile: mackerel: Add HDMI sound support
ARM: mach-shmobile: mackerel: add HDMI video support
ARM: mach-shmobile: ap4evb: fixup clk_put timing of fsib_clk
ARM: mach-shmobile: sh73a0: fix div4 table
ARM: mach-shmobile: ap4/mackerel: modify wrong comment out of USB
ARM: mach-shmobile: Mackerel VGA camera support
mmc: sh_mmcif: make DMA support by the driver unconditional
ARM: mach-shmobile: Add eMMC support through MMCIF on AG5EVM
ARM: mach-shmobile: Use pullups for AG5EVM KEYSC pins
ARM: mach-shmobile: sh73a0 GPIO pullup improvement
...
|
