| Age | Commit message (Collapse) | Author |
|---|
|
Properties in the device tree are specified as big-endian. At present,
the only platforms to support device trees are also big-endian, so we've
been acessing the properties as raw values.
We'd like to add device tree support to little-endian platforms too, so
add endian conversion to the sites where we access property values in
the common of code.
Compiled on powerpc (ppc44x_defconfig & ppc64_defconfig) and arm (fdt
support only for now).
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Currently, we're using u32 for cell values, and hence assuming
host-endian device trees.
As we'd like to support little-endian platforms, use a __be32 for cell
values, and convert in the cell accessors.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
At present we're using hard-coded values for defaults when parsing the
FDT. This change uses the #defines instead.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
At present, the fdt code sets the kernel-wide initrd_start and
initrd_end variables when parsing /chosen. On ARM, we only set these
once the bootmem has been reserved.
This change adds an arch hook to setup the initrd from the device
tree:
void early_init_dt_setup_initrd_arch(unsigned long start,
unsigned long end);
The arch-specific code can then setup the initrd however it likes.
Compiled on powerpc, with CONFIG_BLK_DEV_INITRD=y and =n.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Currenly, proc_devtree.c depends on asm/prom.h to include linux/of.h, to
provide some device-tree definitions (eg, struct property).
Instead, include linux/of.h directly. We still need asm/prom.h for
HAVE_ARCH_DEVTREE_FIXUPS.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
We only need set_node_proc_entry in proc_devtree.c, so move it there.
This fixes the !HAVE_ARCH_DEVTREE_FIXUPS build, as we can't make make
the definition in linux/of.h conditional on this #define (definitions in
asm/prom.h can't be exposed to linux/of.h, due to the enforced #include
ordering).
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
We use a few procfs-specific functions (eg, proc_device_tree_*) which
aren't covered by the current includes. This causes the following build
error on arm:
drivers/of/base.c: In function 'prom_add_property':
drivers/of/base.c:861: error: implicit declaration of function 'proc_device_tree_add_prop'
drivers/of/base.c: In function 'prom_remove_property':
drivers/of/base.c:902: error: implicit declaration of function 'proc_device_tree_remove_prop'
drivers/of/base.c: In function 'prom_update_property':
drivers/of/base.c:946: error: implicit declaration of function 'proc_device_tree_update_prop'
Add proc_fs.h for these prototypes.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Merge common code between PowerPC and Microblaze architectures.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
Merge common function between powerpc, sparc and microblaze. Code is
identical for powerpc and microblaze, but adds a lock (and release) of
the devtree_lock on sparc.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Merge common code between PowerPC and Microblaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Microblaze only has one CPU, it isn't SMP at all. early_init_dt_scan_cpus()
is effectively just a no-op, so remove it.
Microblaze doesn't support hypervisor assisted dump either, so the phyp stuff
can also go.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
|
|
In struct device_node, the phandle is named 'linux_phandle' for PowerPC
and MicroBlaze, and 'node' for SPARC. There is no good reason for the
difference, it is just an artifact of the code diverging over a couple
of years. This patch renames both to simply .phandle.
Note: the .node also existed in PowerPC/MicroBlaze, but the only user
seems to be arch/powerpc/platforms/powermac/pfunc_core.c. It doesn't
look like the assignment between .linux_phandle and .node is
significantly different enough to warrant the separate code paths
unless ibm,phandle properties actually appear in Apple device trees.
I think it is safe to eliminate the old .node property and use
phandle everywhere.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge common code between PowerPC and MicroBlaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge common code between PowerPC and Microblaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
sched: Fix vmark regression on big machines
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: retry FS IOs even if it has failed with AC_ERR_INVALID
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix race in tty_fasync
serial: serial_cs: oxsemi quirk breaks resume
serial: imx: bit &/| confusion
serial: Fix crash if the minimum rate of the device is > 9600 baud
serial-core: resume serial hardware with no_console_suspend
serial: 8250_pnp: use wildcard for serial Wacom tablets
nozomi: quick fix for the close/close bug
compat_ioctl: Supress "unknown cmd" message on serial /dev/console
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: hv: fix smp problems in the hyperv core code
Staging: et131x: Fix 2.6.33rc1 regression in et131x
Staging: asus_oled: fix oops in 2.6.32.2
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
driver-core: fix devtmpfs crash on s390
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
USB: isp1362: better 64bit printf warning fixes
USB: fix usbstorage for 2770:915d delivers no FAT
USB: Fix level of isp1760 Reloading ptd error message
USB: FHCI: avoid NULL pointer dereference
USB: Fix duplicate sysfs problem after device reset.
USB: add speed values for USB 3.0 and wireless controllers
USB: add missing delay during remote wakeup
USB: EHCI & UHCI: fix race between root-hub suspend and port resume
USB: EHCI: fix handling of unusual interrupt intervals
USB: Don't use GFP_KERNEL while we cannot reset a storage device
USB: fix bitmask merge error
usb: serial: fix memory leak in generic driver
USB: serial: fix USB serial fix kfifo_len locking
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
fs/bio.c: fix shadows sparse warning
drbd: The kernel code is now equivalent to out of tree release 8.3.7
drbd: Allow online resizing of DRBD devices while peer not reachable (needs to be explicitly forced)
drbd: Don't go into StandAlone mode when authentification failes because of network error
drivers/block/drbd/drbd_receiver.c: correct NULL test
cfq-iosched: Respect ioprio_class when preempting
genhd: overlapping variable definition
block: removed unused as_io_context
DM: Fix device mapper topology stacking
block: bdev_stack_limits wrapper
block: Fix discard alignment calculation and printing
block: Correct handling of bottom device misaligment
drbd: check on CONFIG_LBDAF, not LBD
drivers/block/drbd: Correct NULL test
drbd: Silenced an assert that could triggered after changing write ordering method
drbd: Kconfig fix
drbd: Fix for a race between IO and a detach operation [Bugz 262]
drbd: Use drbd_crypto_is_hash() instead of an open coded check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI: delete acpi_processor_power_verify_c2()
ACPI: allow C3 > 1000usec
ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
ACPI: power_meter: remove double kfree()
ACPI: processor: restrict early _PDC to opt-in platforms
ACPI: Fix unused variable warning in sbs.c
acpi: make ACPI device id constant
sony-laptop - fix using of uninitialized variable
ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
eeepc-laptop: disable wireless hotplug for 1201N
eeepc-laptop: add hotplug_disable parameter
eeepc-laptop: switch to using sparse keymap library
eeepc-laptop: dmi blacklist to disable pci hotplug code
eeepc-laptop: disable cpu speed control on EeePC 701
ACPI: don't cond_resched if irq is disabled
ACPI: Remove unnecessary cast.
ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
ACPI: EC: Add wait for irq storm
ACPI: SBS: Move SBS HC callback to faster Notify queue
x86, ACPI: delete acpi_boot_table_init() return value
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
ecryptfs: use after free
ecryptfs: Eliminate useless code
ecryptfs: fix interpose/interpolate typos in comments
ecryptfs: pass matching flags to interpose as defined and used there
ecryptfs: remove unnecessary d_drop calls in ecryptfs_link
ecryptfs: don't ignore return value from lock_rename
ecryptfs: initialize private persistent file before dereferencing pointer
eCryptfs: Remove mmap from directory operations
eCryptfs: Add getattr function
eCryptfs: Use notify_change for truncating lower inodes
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix possible panic on unmount
Btrfs: deal with NULL acl sent to btrfs_set_acl
Btrfs: fix regression in orphan cleanup
Btrfs: Fix race in btrfs_mark_extent_written
Btrfs, fix memory leaks in error paths
Btrfs: align offsets for btrfs_ordered_update_i_size
btrfs: fix missing last-entry in readdir(3)
|
|
In free_unmap_area_noflush(), va->flags is marked as VM_LAZY_FREE first, and
then vmap_lazy_nr is increased atomically.
But, in __purge_vmap_area_lazy(), while traversing of vmap_are_list, nr
is counted by checking VM_LAZY_FREE is set to va->flags. After counting
the variable nr, kernel reads vmap_lazy_nr atomically and checks a
BUG_ON condition whether nr is greater than vmap_lazy_nr to prevent
vmap_lazy_nr from being negative.
The problem is that, if interrupted right after marking VM_LAZY_FREE,
increment of vmap_lazy_nr can be delayed. Consequently, BUG_ON
condition can be met because nr is counted more than vmap_lazy_nr.
It is highly probable when vmalloc/vfree are called frequently. This
scenario have been verified by adding delay between marking VM_LAZY_FREE
and increasing vmap_lazy_nr in free_unmap_area_noflush().
Even the vmap_lazy_nr is for checking high watermark, it never be the
strict watermark. Although the BUG_ON condition is to prevent
vmap_lazy_nr from being negative, vmap_lazy_nr is signed variable. So,
it could go down to negative value temporarily.
Consequently, removing the BUG_ON condition is proper.
A possible BUG_ON message is like the below.
kernel BUG at mm/vmalloc.c:517!
invalid opcode: 0000 [#1] SMP
EIP: 0060:[<c04824a4>] EFLAGS: 00010297 CPU: 3
EIP is at __purge_vmap_area_lazy+0x144/0x150
EAX: ee8a8818 EBX: c08e77d4 ECX: e7c7ae40 EDX: c08e77ec
ESI: 000081fe EDI: e7c7ae60 EBP: e7c7ae64 ESP: e7c7ae3c
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Call Trace:
[<c0482ad9>] free_unmap_vmap_area_noflush+0x69/0x70
[<c0482b02>] remove_vm_area+0x22/0x70
[<c0482c15>] __vunmap+0x45/0xe0
[<c04831ec>] vmalloc+0x2c/0x30
Code: 8d 59 e0 eb 04 66 90 89 cb 89 d0 e8 87 fe ff ff 8b 43 20 89 da 8d 48 e0 8d 43 20 3b 04 24 75 e7 fe 05 a8 a5 a3 c0 e9 78 ff ff ff <0f> 0b eb fe 90 8d b4 26 00 00 00 00 56 89 c6 b8 ac a5 a3 c0 31
EIP: [<c04824a4>] __purge_vmap_area_lazy+0x144/0x150 SS:ESP 0068:e7c7ae3c
[ See also http://marc.info/?l=linux-kernel&m=126335856228090&w=2 ]
Signed-off-by: Yongseok Koh <yongseok.koh@samsung.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh64: wire up sys_accept4.
sh: unwire sys_recvmmsg.
sh: ms7724: Correct sh-eth EEPROM polling timeout.
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
ARM: 5884/1: arm: Fix DCC console for v7
ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
ARM: fix badly placed mach/plat entries in Kconfig & Makefile
|
|
Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: Stephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The is_software_event() definition always confuses me because its an
exclusive expression, make it an inclusive one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Anton reported that perf record kept receiving events even after calling
ioctl(PERF_EVENT_IOC_DISABLE). It turns out that FORK,COMM and MMAP
events didn't respect the disabled state and kept flowing in.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Anton Blanchard <anton@samba.org>
LKML-Reference: <1263459187.4244.265.camel@laptop>
CC: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Paul questioned the context in which we should call
perf_event_do_pending(). After looking at that I found that it should be
called from IRQ context these days, however the fallback call-site is
placed in softirq context. Ammend this by placing the callback in the IRQ
timer path.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1263374859.4244.192.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Assume A->B schedule is processing, if B have acquired BKL before and it
need reschedule this time. Then on B's context, it will go to
need_resched_nonpreemptible for reschedule. But at this time, prev and
switch_count are related to A. It's wrong and will lead to incorrect
scheduler statistics.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <2674af741001102238w7b0ddcadref00d345e2181d11@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
SD_PREFER_SIBLING is set at the CPU domain level if power saving isn't
enabled, leading to many cache misses on large machines as we traverse
looking for an idle shared cache to wake to. Change the enabler of
select_idle_sibling() to SD_SHARE_PKG_RESOURCES, and enable same at the
sibling domain level.
Reported-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1262612696.15495.15.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
There was some left over #ifdef ARM logic that is outdated but no one
really noticed. So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings. So use %zu for sizeof() values. This is a
better version of the previous commit b0a9cf297e58721933.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Resolves kernel.org bug 14914.
Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).
The patch works, but let me clarify a few things about it. All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think). I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear. Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine. Starting with
2.6.30, things no longer work.
Signed-off-by: Ryan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Assign fhci only if usb is not NULL.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate. It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:
[ 427.681810] Restarting tasks ...
[ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 427.682019] usb usb3: usb resume
[ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 427.682205] usb 1-2: usb wakeup-resume
[ 427.682226] usb 1-2: finish reset-resume
[ 427.682886] done.
[ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.746682] hub 3-0:1.0: hub_reset_resume
[ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[ 427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[ 427.916609] ep_81: create, parent hub
[ 427.916632] ------------[ cut here ]------------
[ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[ 427.916649] Hardware name: System Product Name
[ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[ 427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869a-dirty #13
[ 427.916699] Call Trace:
The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.
After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces. However, the
USB core keeps track of the old state, which may include non-zero
alternate settings. It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.
The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0. This caused duplicate
endpoint files to be created.
The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: Kurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost. When remote wakeup is
enabled, this is undesirable behavior.
The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.
URBs with an interval of 2 or 4 microframes aren't handled.
For the time being, the patch reduces to interval to 1 uframe.
URBs are constrained to have an interval no larger than 1024
frames by usb_submit_urb(). But some EHCI controllers allow
use of a schedule as short as 256 frames; for these
controllers we may have to decrease the interval to the
actual schedule length.
The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames. But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Glynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix a regression introduced by commit
715b1dc01fe44537e8fce9566e4bb48d6821d84b ("USB: usb_debug,
usb_generic_serial: implement multi urb write").
URB transfer buffer was never freed when using multi-urb writes.
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
