| Age | Commit message (Collapse) | Author |
|---|
|
Add a strong pullup option to the w1 system. This supplies extra power
for parasite powered devices. There is a w1_master_pullup sysfs entry and
enable_pullup module parameter to enable or disable the strong pullup.
The one wire bus requires at a minimum one wire and ground. The common
wire is used for sending and receiving data as well as supplying power to
devices that are parasite powered of which temperature sensors can be one
example. The bus must be idle and left high while a temperature
conversion is in progress, in addition the normal pullup resister on
larger networks or even higher temperatures might not supply enough power.
The pullup resister can't provide too much pullup current, because
devices need to pull the bus down to write a value. This enables the
strong pullup for supported hardware, which can supply more current when
requested. Unsupported hardware will just delay with the bus high.
The hardware USB 2490 one wire bus master has a bit on some commands which
will enable the strong pullup as soon as the command finishes executing.
To use strong pullup, call the new w1_next_pullup function to register the
duration. The next write command will call set_pullup before sending the
data, and reset the duration to zero once it returns.
Switched from simple_strtol to strict_strtol.
Signed-off-by: David Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The w1_process thread's sleeping and termination has been modified.
msleep_interruptible was replaced by schedule_timeout and schedule to
allow for kthread_stop and wake_up_process to interrupt the sleep and the
unbounded sleeping when a bus search is disabled. The W1_MASTER_NEED_EXIT
and flags variable were removed as they were redundant with
kthread_should_stop and kthread_stop. If w1_process is sleeping,
requesting a search will immediately wake it up rather than waiting for
the end of msleep_interruptible previously.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the creation of the w1_process thread to after the device has been
initialized. This way w1_process doesn't have to check to see if it has
been initialized and the bus search can proceed without sleeping. That
also eliminates two checks in the w1_process loop. The sleep now happens
at the end of the loop not the beginning.
Also added a comment for why the atomic_set was 2.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Early abort if the master driver or the hardware goes away in the middle
of a bus search operation. The alternative is to spam the print buffer up
to 64*64 times with read errors in the case of USB.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
w1_control_thread was removed which would wake up every second and process
newly registered family codes and complete some final cleanup for a
removed master. Those routines were moved to the threads that were
previously requesting those operations. A new function
w1_reconnect_slaves takes care of reconnecting existing slave devices when
a new family code is registered or removed. The removal case was missing
and would cause a deadlock waiting for the family code reference count to
decrease, which will now happen. A problem with registering a family code
was fixed. A slave device would be unattached if it wasn't yet claimed,
then attached at the end of the list, two unclaimed slaves would cause an
infinite loop.
The struct w1_bus_master.search now takes a pointer to the struct
w1_master device to avoid searching for it, which would have caused a
lock ordering deadlock with the removal of w1_control_thread.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
tpm_register_hardware() leaks devname on an error path.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11425
Reported-by: Daniel Marjamki <danielm77@spray.se>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch tpm-correct-tpm-timeouts-to-jiffies-conversion reveals a bug in the
Broadcom BCM0102 TPM chipset used in the Dell Latitude D820 - although
most of the timeouts are returned in usecs as per the spec, one is
apparently returned in msecs, which results in a too-small value leading
to a timeout when the code treats it as usecs. To prevent a regression,
we check for the known too-short value and adjust it to a value that makes
things work.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Marcin Obara <marcin_obara@users.sourceforge.net>
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes timeouts conversion to jiffies, by replacing
msecs_to_jiffies() calls with usecs_to_jiffies(). According to TCG TPM
Specification Version 1.2 Revision 103 (pages 166, 167) TPM timeouts and
durations are returned in microseconds (usec) not in miliseconds (msec).
This fixes a long hang while loading TPM driver, if TPM chip starts in
"Idle" state instead of "Ready" state. Without this patch - 'modprobe'
may hang for 30 seconds or more.
Signed-off-by: Marcin Obara <marcin_obara@users.sourceforge.net>
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove CVS keywords that weren't updated for a long time from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cannot assume writes will fully complete, so this conversion goes the easy
way and always brings the page uptodate before the write.
[dhowells@redhat.com: style tweaks]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make the Thermal messages (temperature got past Tmid) be displayed only
once because:
1) it's the BIOS job to configure and handle the memory throttling
2) if the BIOS is broken or is aware about the condition, flooding the
system logs won't help anything.
3) According to the specification update for Intel 5000 MCHs, all the
revisions of this MCH have problems on the thermal sensors, making
not automatic (a.k.a. intelligent thermal throttling) impossible.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the i5000_edac messages, making everything pass through the EDAC
(so the log controls will work) and being more specific about the errors.
Also, it makes the miscellaneous errors optional and disabled by default.
As I didn't found anywhere information about M23ERR-M26ERR
(FERR_NF_THERMAL) on FERR_NF_FBD, I'm removing them.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds support for the dual-core MPC8572 processor. We have
to support making SPR changes on each core. Also, since we can
have multiple memory controllers sharing an interrupt, flag the
interrupts with IRQF_SHARED.
Signed-off-by: Andrew Kilkenny <akilkenny@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix 443BX/GX MCH suppport in a EDAC.
It makes i82443bxgx_edac coexist with intel_agp using the same approach as
several other EDAC drivers.
Tested on Intel's L443GX with redhat's 2.6.18 with whole EDAC subsystem
backported a while ago.
[root@host ~]# dmesg|grep -iE '(AGP|EDAC)'
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440GX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
EDAC MC: Ver: 2.1.0 Jun 27 2008
EDAC MC0: Giving out device to 'i82443bxgx_edac' 'I82443BXGX': DEV 0000:00:00.0
EDAC PCI0: Giving out device to module 'i82443bxgx_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
Signed-off-by: Vladislav Bogdanov <slava@nsys.by>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
task_child_reaper() has no callers anymore, kill it.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
de_thread() checks if the old leader was the ->child_reaper, this is not
possible any longer. With the previous patch ->group_leader itself will
change ->child_reaper on exit.
Henceforth find_new_reaper() is the only function (apart from
initialization) which plays with ->child_reaper.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move it into sysrq.c, along with the rest of the sysrq implementation.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We currently follow blindly what the partition table lies about the
disk, and let the kernel create block devices which can not be accessed.
Trying to identify the device leads to kernel logs full of:
sdb: rw=0, want=73392, limit=28800
attempt to access beyond end of device
Here is an example of a broken partition table, where sda2 starts
behind the end of the disk, and sdb3 is larger than the entire disk:
Disk /dev/sdb: 14 MB, 14745600 bytes
1 heads, 29 sectors/track, 993 cylinders, total 28800 sectors
Device Boot Start End Blocks Id System
/dev/sdb1 29 7800 3886 83 Linux
/dev/sdb2 37801 45601 3900+ 83 Linux
/dev/sdb3 15602 73402 28900+ 83 Linux
/dev/sdb4 23403 28796 2697 83 Linux
The kernel creates these completely invalid devices, which can not be
accessed, or may lead to other unpredictable failures:
grep . /sys/class/block/sdb*/{start,size}
/sys/class/block/sdb/size:28800
/sys/class/block/sdb1/start:29
/sys/class/block/sdb1/size:7772
/sys/class/block/sdb2/start:37801
/sys/class/block/sdb2/size:7801
/sys/class/block/sdb3/start:15602
/sys/class/block/sdb3/size:57801
/sys/class/block/sdb4/start:23403
/sys/class/block/sdb4/size:5394
With this patch, we ignore partitions which start behind the end of the disk,
and limit partitions to the end of the disk if they pretend to be larger:
grep . /sys/class/block/sdb*/{start,size}
/sys/class/block/sdb/size:28800
/sys/class/block/sdb1/start:29
/sys/class/block/sdb1/size:7772
/sys/class/block/sdb3/start:15602
/sys/class/block/sdb3/size:13198
/sys/class/block/sdb4/start:23403
/sys/class/block/sdb4/size:5394
These warnings are printed to the kernel log:
sdb: p2 ignored, start 37801 is behind the end of the disk
sdb: p3 size 57801 limited to end of disk
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I missed this when I did the arm26 removal.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert printks to use dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The only use is to pass this to le16_to_cpu, declare as such
drivers/char/moxa.c:548:11: warning: cast to restricted __le16.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code scriblles over a local pointer whereas it appears to be trying
to write to the memory at which that pointer points.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11397
Nobody we know can test this change.
Reported-by: Zvonimir Rakamaric <zrakamar@cs.ubc.ca>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ds1286_get_time(); is not called from atomic context, sleep for 20 ms is
better choice than a (home-made) busy waiting for such a situation.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Don't repeat BINFMT_ELF definition, simply multiply COMPAT and BINFMT_ELF.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These auxvec entries are the only ones left unhandled out of the current
base implementation. This syncs up binfmt_elf_fdpic with linux/auxvec.h
and current binfmt_elf.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
binfmt_elf_fdpic seems to have grabbed a hard-coded hack from an ancient
version of binfmt_elf in order to try and fix up initial stack alignment
on multi-threaded x86, which while in addition to being unused, was also
pushed down beyond the first set of operations on the stack pointer,
negating the entire purpose.
These days, we have an architecture independent arch_align_stack(), so we
switch to using that instead. Move the initial alignment up before the
initial stores while we're at it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 483fad1c3fa1060d7e6710e84a065ad514571739 ("ELF loader support for
auxvec base platform string") introduced AT_BASE_PLATFORM, but only
implemented it for binfmt_elf.
Given that AT_VECTOR_SIZE_BASE is unconditionally enlarged for us, and
it's only optionally added in for the platforms that set
ELF_BASE_PLATFORM, wire it up for binfmt_elf_fdpic, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update Erik Mouw's email address & affiliation in DocBook.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Erik Mouw <mouw@nl.linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove CVS keywords that weren't updated for a long time from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In case of error, the function open_xa_dir returns an ERR pointer, but
never returns a NULL pointer. So a NULL test that comes after an IS_ERR
test should be deleted.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@match_bad_null_test@
expression x, E;
statement S1,S2;
@@
x = open_xa_dir(...)
... when != x = E
(
* if (x == NULL && ...) S1 else S2
|
* if (x == NULL || ...) S1 else S2
)
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove CVS keywords that weren't updated for a long time from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a stack corruption caused by a corrupted hfs filesystem. If the
catalog name length is corrupted the memcpy overwrites the catalog btree
structure. Since the field is limited to HFS_NAMELEN bytes in the
structure and the file format, we throw an error if it is too long.
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While testing more corrupted images with hfsplus, i came across
one which triggered the following bug:
[15840.675016] BUG: unable to handle kernel paging request at fffffffb
[15840.675016] IP: [<c0116a4f>] kmap+0x15/0x56
[15840.675016] *pde = 00008067 *pte = 00000000
[15840.675016] Oops: 0000 [#1] PREEMPT DEBUG_PAGEALLOC
[15840.675016] Modules linked in:
[15840.675016]
[15840.675016] Pid: 11575, comm: ln Not tainted (2.6.27-rc4-00123-gd3ee1b4-dirty #29)
[15840.675016] EIP: 0060:[<c0116a4f>] EFLAGS: 00010202 CPU: 0
[15840.675016] EIP is at kmap+0x15/0x56
[15840.675016] EAX: 00000246 EBX: fffffffb ECX: 00000000 EDX: cab919c0
[15840.675016] ESI: 000007dd EDI: cab0bcf4 EBP: cab0bc98 ESP: cab0bc94
[15840.675016] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[15840.675016] Process ln (pid: 11575, ti=cab0b000 task=cab919c0 task.ti=cab0b000)
[15840.675016] Stack: 00000000 cab0bcdc c0231cfb 00000000 cab0bce0 00000800 ca9290c0 fffffffb
[15840.675016] cab145d0 cab919c0 cab15998 22222222 22222222 22222222 00000001 cab15960
[15840.675016] 000007dd cab0bcf4 cab0bd04 c022cb3a cab0bcf4 cab15a6c ca9290c0 00000000
[15840.675016] Call Trace:
[15840.675016] [<c0231cfb>] ? hfsplus_block_allocate+0x6f/0x2d3
[15840.675016] [<c022cb3a>] ? hfsplus_file_extend+0xc4/0x1db
[15840.675016] [<c022ce41>] ? hfsplus_get_block+0x8c/0x19d
[15840.675016] [<c06adde4>] ? sub_preempt_count+0x9d/0xab
[15840.675016] [<c019ece6>] ? __block_prepare_write+0x147/0x311
[15840.675016] [<c0161934>] ? __grab_cache_page+0x52/0x73
[15840.675016] [<c019ef4f>] ? block_write_begin+0x79/0xd5
[15840.675016] [<c022cdb5>] ? hfsplus_get_block+0x0/0x19d
[15840.675016] [<c019f22a>] ? cont_write_begin+0x27f/0x2af
[15840.675016] [<c022cdb5>] ? hfsplus_get_block+0x0/0x19d
[15840.675016] [<c0139ebe>] ? tick_program_event+0x28/0x4c
[15840.675016] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[15840.675016] [<c022b723>] ? hfsplus_write_begin+0x2d/0x32
[15840.675016] [<c022cdb5>] ? hfsplus_get_block+0x0/0x19d
[15840.675016] [<c0161988>] ? pagecache_write_begin+0x33/0x107
[15840.675016] [<c01879e5>] ? __page_symlink+0x3c/0xae
[15840.675016] [<c019ad34>] ? __mark_inode_dirty+0x12f/0x137
[15840.675016] [<c0187a70>] ? page_symlink+0x19/0x1e
[15840.675016] [<c022e6eb>] ? hfsplus_symlink+0x41/0xa6
[15840.675016] [<c01886a9>] ? vfs_symlink+0x99/0x101
[15840.675016] [<c018a2f6>] ? sys_symlinkat+0x6b/0xad
[15840.675016] [<c018a348>] ? sys_symlink+0x10/0x12
[15840.675016] [<c01038bd>] ? sysenter_do_call+0x12/0x31
[15840.675016] =======================
[15840.675016] Code: 00 00 75 10 83 3d 88 2f ec c0 02 75 07 89 d0 e8 12 56 05 00 5d c3 55 ba 06 00 00 00 89 e5 53 89 c3 b8 3d eb 7e c0 e8 16 74 00 00 <8b> 03 c1 e8 1e 69 c0 d8 02 00 00 05 b8 69 8e c0 2b 80 c4 02 00
[15840.675016] EIP: [<c0116a4f>] kmap+0x15/0x56 SS:ESP 0068:cab0bc94
[15840.675016] ---[ end trace 4fea40dad6b70e5f ]---
This happens because the return value of read_mapping_page() is passed on
to kmap unchecked. The bug is triggered after the first
read_mapping_page() in hfsplus_block_allocate(), this patch fixes all
three usages in this functions but leaves the ones further down in the
file unchanged.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When an hfsplus image gets corrupted it might happen that the catalog
namelength field gets b0rked. If we mount such an image the memcpy() in
hfsplus_cat_build_key_uni() writes more than the 255 that fit in the name
field. Depending on the size of the overwritten data, we either only get
memory corruption or also trigger an oops like this:
[ 221.628020] BUG: unable to handle kernel paging request at c82b0000
[ 221.629066] IP: [<c022d4b1>] hfsplus_find_cat+0x10d/0x151
[ 221.629066] *pde = 0ea29163 *pte = 082b0160
[ 221.629066] Oops: 0002 [#1] PREEMPT DEBUG_PAGEALLOC
[ 221.629066] Modules linked in:
[ 221.629066]
[ 221.629066] Pid: 4845, comm: mount Not tainted (2.6.27-rc4-00123-gd3ee1b4-dirty #28)
[ 221.629066] EIP: 0060:[<c022d4b1>] EFLAGS: 00010206 CPU: 0
[ 221.629066] EIP is at hfsplus_find_cat+0x10d/0x151
[ 221.629066] EAX: 00000029 EBX: 00016210 ECX: 000042c2 EDX: 00000002
[ 221.629066] ESI: c82d70ca EDI: c82b0000 EBP: c82d1bcc ESP: c82d199c
[ 221.629066] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[ 221.629066] Process mount (pid: 4845, ti=c82d1000 task=c8224060 task.ti=c82d1000)
[ 221.629066] Stack: c080b3c4 c82aa8f8 c82d19c2 00016210 c080b3be c82d1bd4 c82aa8f0 00000300
[ 221.629066] 01000000 750008b1 74006e00 74006900 65006c00 c82d6400 c013bd35 c8224060
[ 221.629066] 00000036 00000046 c82d19f0 00000082 c8224548 c8224060 00000036 c0d653cc
[ 221.629066] Call Trace:
[ 221.629066] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[ 221.629066] [<c013bca3>] ? trace_hardirqs_off_caller+0x14/0x9b
[ 221.629066] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[ 221.629066] [<c013bca3>] ? trace_hardirqs_off_caller+0x14/0x9b
[ 221.629066] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[ 221.629066] [<c0107aa3>] ? native_sched_clock+0x82/0x96
[ 221.629066] [<c01302d2>] ? __kernel_text_address+0x1b/0x27
[ 221.629066] [<c010487a>] ? dump_trace+0xca/0xd6
[ 221.629066] [<c0109e32>] ? save_stack_address+0x0/0x2c
[ 221.629066] [<c0109eaf>] ? save_stack_trace+0x1c/0x3a
[ 221.629066] [<c013b571>] ? save_trace+0x37/0x8d
[ 221.629066] [<c013b62e>] ? add_lock_to_list+0x67/0x8d
[ 221.629066] [<c013ea1c>] ? validate_chain+0x8a4/0x9f4
[ 221.629066] [<c013553d>] ? down+0xc/0x2f
[ 221.629066] [<c013f1f6>] ? __lock_acquire+0x68a/0x6e0
[ 221.629066] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[ 221.629066] [<c013bca3>] ? trace_hardirqs_off_caller+0x14/0x9b
[ 221.629066] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[ 221.629066] [<c0107aa3>] ? native_sched_clock+0x82/0x96
[ 221.629066] [<c013da5d>] ? mark_held_locks+0x43/0x5a
[ 221.629066] [<c013dc3a>] ? trace_hardirqs_on+0xb/0xd
[ 221.629066] [<c013dbf4>] ? trace_hardirqs_on_caller+0xf4/0x12f
[ 221.629066] [<c06abec8>] ? _spin_unlock_irqrestore+0x42/0x58
[ 221.629066] [<c013555c>] ? down+0x2b/0x2f
[ 221.629066] [<c022aa68>] ? hfsplus_iget+0xa0/0x154
[ 221.629066] [<c022b0b9>] ? hfsplus_fill_super+0x280/0x447
[ 221.629066] [<c0107aa3>] ? native_sched_clock+0x82/0x96
[ 221.629066] [<c013bca3>] ? trace_hardirqs_off_caller+0x14/0x9b
[ 221.629066] [<c013bca3>] ? trace_hardirqs_off_caller+0x14/0x9b
[ 221.629066] [<c013f1f6>] ? __lock_acquire+0x68a/0x6e0
[ 221.629066] [<c041c9e4>] ? string+0x2b/0x74
[ 221.629066] [<c041cd16>] ? vsnprintf+0x2e9/0x512
[ 221.629066] [<c010487a>] ? dump_trace+0xca/0xd6
[ 221.629066] [<c0109eaf>] ? save_stack_trace+0x1c/0x3a
[ 221.629066] [<c0109eaf>] ? save_stack_trace+0x1c/0x3a
[ 221.629066] [<c013b571>] ? save_trace+0x37/0x8d
[ 221.629066] [<c013b62e>] ? add_lock_to_list+0x67/0x8d
[ 221.629066] [<c013ea1c>] ? validate_chain+0x8a4/0x9f4
[ 221.629066] [<c01354d3>] ? up+0xc/0x2f
[ 221.629066] [<c013f1f6>] ? __lock_acquire+0x68a/0x6e0
[ 221.629066] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[ 221.629066] [<c013bca3>] ? trace_hardirqs_off_caller+0x14/0x9b
[ 221.629066] [<c013bd35>] ? trace_hardirqs_off+0xb/0xd
[ 221.629066] [<c0107aa3>] ? native_sched_clock+0x82/0x96
[ 221.629066] [<c041cfb7>] ? snprintf+0x1b/0x1d
[ 221.629066] [<c01ba466>] ? disk_name+0x25/0x67
[ 221.629066] [<c0183960>] ? get_sb_bdev+0xcd/0x10b
[ 221.629066] [<c016ad92>] ? kstrdup+0x2a/0x4c
[ 221.629066] [<c022a7b3>] ? hfsplus_get_sb+0x13/0x15
[ 221.629066] [<c022ae39>] ? hfsplus_fill_super+0x0/0x447
[ 221.629066] [<c0183583>] ? vfs_kern_mount+0x3b/0x76
[ 221.629066] [<c0183602>] ? do_kern_mount+0x32/0xba
[ 221.629066] [<c01960d4>] ? do_new_mount+0x46/0x74
[ 221.629066] [<c0196277>] ? do_mount+0x175/0x193
[ 221.629066] [<c013dbf4>] ? trace_hardirqs_on_caller+0xf4/0x12f
[ 221.629066] [<c01663b2>] ? __get_free_pages+0x1e/0x24
[ 221.629066] [<c06ac07b>] ? lock_kernel+0x19/0x8c
[ 221.629066] [<c01962e6>] ? sys_mount+0x51/0x9b
[ 221.629066] [<c01962f9>] ? sys_mount+0x64/0x9b
[ 221.629066] [<c01038bd>] ? sysenter_do_call+0x12/0x31
[ 221.629066] =======================
[ 221.629066] Code: 89 c2 c1 e2 08 c1 e8 08 09 c2 8b 85 e8 fd ff ff 66 89 50 06 89 c7 53 83 c7 08 56 57 68 c4 b3 80 c0 e8 8c 5c ef ff 89 d9 c1 e9 02 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 83 c3 06 8b 95 e8 fd ff ff 0f
[ 221.629066] EIP: [<c022d4b1>] hfsplus_find_cat+0x10d/0x151 SS:ESP 0068:c82d199c
[ 221.629066] ---[ end trace e417a1d67f0d0066 ]---
Since hfsplus_cat_build_key_uni() returns void and only has one callsite,
the check is performed at the callsite.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Check whether the file system was to be mounted read only anyway before
warning about changing the mount to read only.
Signed-off-by: Mike Crowe <mac@mcrowe.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Does compile-time byteswapping rather than runtime.
Noticed by sparse:
fs/befs/super.c:29:6: warning: cast to restricted __le32
fs/befs/super.c:29:6: warning: cast from restricted fs32
fs/befs/super.c:31:11: warning: cast to restricted __be32
fs/befs/super.c:31:11: warning: cast from restricted fs32
fs/befs/super.c:31:11: warning: cast to restricted __be32
fs/befs/super.c:31:11: warning: cast from restricted fs32
fs/befs/super.c:31:11: warning: cast to restricted __be32
fs/befs/super.c:31:11: warning: cast from restricted fs32
fs/befs/super.c:31:11: warning: cast to restricted __be32
fs/befs/super.c:31:11: warning: cast from restricted fs32
fs/befs/super.c:31:11: warning: cast to restricted __be32
fs/befs/super.c:31:11: warning: cast from restricted fs32
fs/befs/super.c:31:11: warning: cast to restricted __be32
fs/befs/super.c:31:11: warning: cast from restricted fs32
fs/befs/linuxvfs.c:811:7: warning: cast to restricted __le32
fs/befs/linuxvfs.c:811:7: warning: cast from restricted fs32
fs/befs/linuxvfs.c:812:7: warning: cast to restricted __be32
fs/befs/linuxvfs.c:812:7: warning: cast from restricted fs32
fs/befs/linuxvfs.c:812:7: warning: cast to restricted __be32
fs/befs/linuxvfs.c:812:7: warning: cast from restricted fs32
fs/befs/linuxvfs.c:812:7: warning: cast to restricted __be32
fs/befs/linuxvfs.c:812:7: warning: cast from restricted fs32
fs/befs/linuxvfs.c:812:7: warning: cast to restricted __be32
fs/befs/linuxvfs.c:812:7: warning: cast from restricted fs32
fs/befs/linuxvfs.c:812:7: warning: cast to restricted __be32
fs/befs/linuxvfs.c:812:7: warning: cast from restricted fs32
fs/befs/linuxvfs.c:812:7: warning: cast to restricted __be32
fs/befs/linuxvfs.c:812:7: warning: cast from restricted fs32
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: "Sergey S. Kostyliov" <rathamahata@php4.ru>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A very large directory with many read failures (either due to storage
problems, or due to invalid size & blocks from corruption) will generate a
printk storm as the filesystem continues to try to read all the blocks.
This flood of messages can tie up the box until it is complete - which may
be a very long time, especially for very large corrupted values.
This is fixed by only reporting the corruption once each time we try to
read the directory.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We could run into ENOSPC error on ext2, even when there is free blocks on
the filesystem.
The problem is triggered in the case the goal block group has 0 free
blocks , and the rest block groups are skipped due to the check of
"free_blocks < windowsz/2". Current code could fall back to non
reservation allocation to prevent early ENOSPC after examing all the block
groups with reservation on , but this code was bypassed if the reservation
window is turned off already, which is true in this case.
This patch fixed two issues:
1) We don't need to turn off block reservation if the goal block group has
0 free blocks left and continue search for the rest of block groups.
Current code the intention is to turn off the block reservation if the
goal allocation group has a few (some) free blocks left (not enough for
make the desired reservation window),to try to allocation in the goal
block group, to get better locality. But if the goal blocks have 0 free
blocks, it should leave the block reservation on, and continues search for
the next block groups,rather than turn off block reservation completely.
2) we don't need to check the window size if the block reservation is off.
The problem was originally found and fixed in ext4.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove CVS keywords that weren't updated for a long time from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PnP encodes the resource type directly as its struct resource->flags value
which is an unsigned long. Make it so...
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There's no point in printing some ancient version number forever.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam M Belay <abelay@MIT.EDU>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
echo 3 >> /sys/class/graphics/fbcon/rotate_all, then switch to another
console. Result:
BUG: unable to handle kernel paging request at ffffc20005d00000
IP: [bitfill_aligned+149/265] bitfill_aligned+0x95/0x109
PGD 7e228067 PUD 7e229067 PMD 7bc1f067 PTE 0
Oops: 0002 [1] SMP
CPU 1
Modules linked in: [...a lot...]
Pid: 10, comm: events/1 Not tainted 2.6.26.5-45.fc9.x86_64 #1
RIP: 0010:[bitfill_aligned+149/265] [bitfill_aligned+149/265] bitfill_aligned+0x95/0x109
RSP: 0018:ffff81007d811bc8 EFLAGS: 00010216
RAX: ffffc20005d00000 RBX: 0000000000000000 RCX: 0000000000000400
RDX: 0000000000000000 RSI: ffffc20005d00000 RDI: ffffffffffffffff
RBP: ffff81007d811be0 R08: 0000000000000400 R09: 0000000000000040
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000010000
R13: ffffffff811632f0 R14: 0000000000000006 R15: ffff81007cb85400
FS: 0000000000000000(0000) GS:ffff81007e004780(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffffc20005d00000 CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process events/1 (pid: 10, threadinfo ffff81007d810000, task ffff81007d808000)
Stack: ffff81007c9d75a0 0000000000000000 0000000000000000 ffff81007d811c80
ffffffff81163a61 ffff810000000000 ffffffff8115f9c8 0000001000000000
0000000100aaaaaa 000000007cd0d4a0 fffffd8a00000800 0001000000000000
Call Trace:
[cfb_fillrect+523/798] cfb_fillrect+0x20b/0x31e
[soft_cursor+416/436] ? soft_cursor+0x1a0/0x1b4
[ccw_clear_margins+205/263] ccw_clear_margins+0xcd/0x107
[fbcon_clear_margins+59/61] fbcon_clear_margins+0x3b/0x3d
[fbcon_switch+1291/1466] fbcon_switch+0x50b/0x5ba
[redraw_screen+261/481] redraw_screen+0x105/0x1e1
[ccw_cursor+0/1869] ? ccw_cursor+0x0/0x74d
[complete_change_console+48/190] complete_change_console+0x30/0xbe
[change_console+115/120] change_console+0x73/0x78
[console_callback+0/292] ? console_callback+0x0/0x124
[console_callback+97/292] console_callback+0x61/0x124
[schedule_delayed_work+25/30] ? schedule_delayed_work+0x19/0x1e
[run_workqueue+139/282] run_workqueue+0x8b/0x11a
[worker_thread+221/238] worker_thread+0xdd/0xee
[autoremove_wake_function+0/56] ? autoremove_wake_function+0x0/0x38
[worker_thread+0/238] ? worker_thread+0x0/0xee
[kthread+73/118] kthread+0x49/0x76
[child_rip+10/18] child_rip+0xa/0x12
[kthread+0/118] ? kthread+0x0/0x76
[child_rip+0/18] ? child_rip+0x0/0x12
Because fbcon_set_all_vcs()->FBCON_SWAP() uses display->rotate == 0 instead
of fbcon_ops->rotate, and vc_resize() has no effect because it is called with
new_cols/rows == ->vc_cols/rows.
Tested on 2.6.26.5-45.fc9.x86_64, but
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git seems to
have the same problem.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [2.6.27.x, 2.6.26.x, maybe 2.6.25.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add driver for TMIO framebuffer cells as found e.g. in Toshiba TC6393XB
chips.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'm stepping up as maintainer for the Epson S1D13XXXFB driver since I have
2 platforms currently using it.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Acked-by: Thibaut Varene <varenet@parisc-linux.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make alloc_carmine_fb() __devinit.
WARNING: drivers/video/carminefb.o(.text+0x81b): Section mismatch in reference from the function alloc_carmine_fb() to the variable .devinit.data:carminefb_fix
The function alloc_carmine_fb() references the variable __devinitdata
carminefb_fix. This is often because alloc_carmine_fb lacks a
__devinitdata annotation or the annotation of carminefb_fix is wrong.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Support the Matrox G200eV chip, based on timings that I found in the X.org
matrox driver.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Epson s1d13xxx hardware is common in many handhelds, but our driver is
currently locked to a single chip revision. This patch adds an array of
known to work revisions (which can be extended).
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Acked-by: Thibaut Varène <varenet@parisc-linux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, it is possible to set a graphics VESA mode at boot time via the
vga= parameter even when no framebuffer driver supporting this is
configured. This could lead to the system booting with a black screen,
without a usable console.
Fix this problem by only allowing to set graphics modes at boot time if a
supporting framebuffer driver is configured.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
