| Age | Commit message (Collapse) | Author |
|---|
|
This removes custom flag handling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the trace events defined in include/trace/events/bpf.h are only
used when CONFIG_BPF_SYSCALL is defined. But this file gets included by
include/linux/bpf_trace.h which is included by the networking code with
CREATE_TRACE_POINTS defined.
If a trace event is created but not used it still has data structures
and functions created for its use, even though nothing is using them.
To not waste space, do not define the BPF trace events in bpf.h unless
CONFIG_BPF_SYSCALL is defined.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to not dirty the cacheline too often, we try to only update
dst->__use and dst->lastusetime at most once per jiffy.
As dst->lastusetime is only used by ipv6 garbage collector, it should
be good enough time resolution.
And __use is only used in ipv6_route_seq_show() to show how many times a
dst has been used. And as __use is not atomic_t right now, it does not
show the precise number of usage times anyway. So we think it should be
OK to only update it at most once per jiffy.
According to my latest syn flood test on a machine with intel Xeon 6th
gen processor and 2 10G mlx nics bonded together, each with 8 rx queues
on 2 NUMA nodes:
With this patch, the packet process rate increases from ~3.49Mpps to
~3.75Mpps with a 7% increase rate.
Note: dst_use() is being renamed to dst_hold_and_use() to better specify
the purpose of the function.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@googl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In fib6_locate(), we need to first make sure fn is not NULL before doing
FIB6_SUBTREE(fn) to avoid crash.
This fixes the following static checker warning:
net/ipv6/ip6_fib.c:1462 fib6_locate()
warn: variable dereferenced before check 'fn' (see line 1459)
net/ipv6/ip6_fib.c
1458 if (src_len) {
1459 struct fib6_node *subtree = FIB6_SUBTREE(fn);
^^^^^^^^^^^^^^^^
We shifted this dereference
1460
1461 WARN_ON(saddr == NULL);
1462 if (fn && subtree)
^^
before the check for NULL.
1463 fn = fib6_locate_1(subtree, saddr, src_len,
1464 offsetof(struct rt6_info, rt6i_src)
Fixes: 66f5d6ce53e6 ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update to llvm excludes assembly instructions.
llvm git revision is below
commit 65fad7c26569 ("bpf: add inline-asm support")
This change will be part of llvm release 6.0
__ASM_SYSREG_H define is not required for native compile.
-target switch includes appropriate target specific files
while cross compiling
Tested on x86 and arm64.
Signed-off-by: Abhijit Ayarekar <abhijit.ayarekar@caviumnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko <jiri@mellanox.com>
====================
net: sched: remove some tp->q usage
In order to prepare for block sharing, tcf_proto instances need to be
independent on particular qdisc instances. This patchset takes care of
removal of couple occurrences of tp->q usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The callers have this info, they will pass it down to tcf_fill_node.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use tcf_block_q helper to get q pointer to be used for direct call of
sch_tree_lock/unlock instead of tcf_tree_lock/unlock.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use helper to get q pointer per block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tc_u_common is now per-q. With blocks, it has to be converted to be
per-block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using tp->q, use block to get the net pointer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whenever the block->q is set, it can be used instead of tp->q as it
contains the same value. When it is not set, which can't happen now but
it might happen with the follow-up shared blocks introduction, the class
is not set in the result. That would lead to a class lookup instead
of direct class pointer use for classful qdiscs. However, it is not
planned to support classful qdisqs sharing filter blocks, so that may
never happen.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These helpers allows to get a q and netdev pointers
for given block easily.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store net pointer in the block structure. Along the way, introduce
qdisc_net helper which allows to easily obtain net pointer for
qdisc instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare for removal of tp->q and store Qdisc pointer in the block
structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes a slight tweak to mqprio in order to bring the
classid values used back in line with what is used for mq. The general idea
is to reserve values :ffe0 - :ffef to identify hardware traffic classes
normally reported via dev->num_tc. By doing this we can maintain a
consistent behavior with mq for classid where :1 - :ffdf will represent a
physical qdisc mapped onto a Tx queue represented by classid - 1, and the
traffic classes will be mapped onto a known subset of classid values
reserved for our virtual qdiscs.
Note I reserved the range from :fff0 - :ffff since this way we might be
able to reuse these classid values with clsact and ingress which would mean
that for mq, mqprio, ingress, and clsact we should be able to maintain a
similar classid layout.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-10-11: IPoIB Multi Pkey support
This series provides the support for IPoIB Multi Pkey.
InfiniBand Pkeys are the equivalent of Ethernet vlans.
Currently IPoIB device driver supports only default Pkey and IPoIB Pkey child
interfaces are not supported with IPoIB offloads mode, this series will add
the support for that by allowing creating mlx5 multiple IPoIB netdevices with
a non-default Pkey.
mlx5 IPoIB Pkey child interface is smaller version of mlx5i IPoIB interfaces and shares
most of its resources with the parent IPoIB interface, namely RX steering and ring
queue resources.
The only mlx5 resources a child Pkey interface will be creating are the TX rings,
since they should be assigned to a specific Pkey.
mlx5i Pkey netdev is implemented via new mlx5e netdev profile implemented in
mlx5/core/ipoib/ipoib_vlan.c.
The series starts with a refactoring of mlx5e PTP and mlx5 clock implementation
to move the code to be part of mlx5 core rather than mlx5e netdevice, in order to
make mlx5 clock and PTP registration part of the core to be shared with mlx5e
master Ethernet netdev/IPoIB parent netdev and mlx5_ib in the near future.
Add the support for attaching multiple underlay QPs for the different Pkeys
in mlx5 core RX steering.
Add Pkey index to rdma_netdev to add the ability to set PKEY index to lower
IPoIB offload netdev.
Use hash-table to map between DQPN (Destination QP number) to child netdev
for the IPoIB parent netdev to forward RX packets to the corresponding
child Pkey netdev, since the RX rings are shared.
The reset of the series adds the ipoib child Pkey: mlx5e netdev profile,
netdev nods implementation and minimal set of ethtool callbacks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-13
This series contains updates to mqprio and i40e.
Amritha introduces a new hardware offload mode in tc/mqprio where the TCs,
the queue configurations and bandwidth rate limits are offloaded to the
hardware. The existing mqprio framework is extended to configure the queue
counts and layout and also added support for rate limiting. This is
achieved through new netlink attributes for the 'mode' option which takes
values such as 'dcb' (default) and 'channel' and a 'shaper' option for
QoS attributes such as bandwidth rate limits in hw mode 1. Legacy devices
can fall back to the existing setup supporting hw mode 1 without these
additional options where only the TCs are offloaded and then the 'mode'
and 'shaper' options defaults to DCB support. The i40e driver enables the
new mqprio hardware offload mechanism factoring the TCs, queue
configuration and bandwidth rates by creating HW channel VSIs.
In this new mode, the priority to traffic class mapping and the user
specified queue ranges are used to configure the traffic class when the
'mode' option is set to 'channel'. This is achieved by creating HW
channels(VSI). A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC (TC0)
which is for the main VSI. TC0 for the main VSI is also reconfigured as
per user provided queue parameters. Finally, bandwidth rate limits are set
on these traffic classes through the shaper attribute by sending these
rates in addition to the number of TCs and the queue configurations.
Colin Ian King makes an array of constant values "constant".
Alan fixes and issue where on some firmware versions, we were failing to
actually fill out the phy_types which caused ethtool to not report any
link types. Also hardened against a potentially malicious VF by not
letting the VF to reset itself after requesting to change the number of
queues (via ethtool), let the PF reset the VF to institute the requested
changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lucas Bates says:
====================
tc-testing: Test suite updates
This patch series is a roundup of changes to the tc-testing
suite:
- Add test cases for police and mirred modules and some coverage
in already-submitted test categories
- Break the test case files down into more user-friendly sizes
- Bug fix to the tdc.py script's handling of the -l argument
v2: fix the lack of final newlines in two new files (thanks David)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug in the tdc script, where executing tdc
with the -l argument would cause the tests to start running
as opposed to listing all the known test cases.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic unit tests for police and skbmod actions in tc.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original submission had the test cases stored in one
monolithic file. This can be unwieldy to edit, especially as more
test cases are added. This patch removes the original tests.json
file in favour of individual ones broken down by category.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tests for flushing gact and mirred were missing. This patch
adds test cases to explicitly test the flush of any installed
gact/mirred actions.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander Duyck says:
====================
net: Minor macvlan source mode cleanups
So this patch series is just a few minor cleanups for macvlan source mode.
The first patch addresses double receives when a packet is being routed to
the macvlan destination address, and the other addresses the pkt_type being
updated in cases where it most likely should not be.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the pkt_type to PACKET_HOST only if the destination MAC
address matches on the on the source based macvlan. It didn't make sense to
be updating broadcast, multicast, and non-local destined frames with
PACKET_HOST.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.
The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.
Fixes: 79cf79abce71 ("macvlan: add source mode")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need a real-time notification for tcp retransmission
for monitoring.
Of course we could use ftrace to dynamically instrument this
kernel function too, however we can't retrieve the connection
information at the same time, for example perf-tools [1] reads
/proc/net/tcp for socket details, which is slow when we have
a lots of connections.
Therefore, this patch adds a tracepoint for __tcp_retransmit_skb()
and exposes src/dst IP addresses and ports of the connection.
This also makes it easier to integrate into perf.
Note, I expose both IPv4 and IPv6 addresses at the same time:
for a IPv4 socket, v4 mapped address is used as IPv6 addresses,
for a IPv6 socket, LOOPBACK4_IPV6 is already filled by kernel.
Also, add sk and skb pointers as they are useful for BPF.
1. https://github.com/brendangregg/perf-tools/blob/master/net/tcpretrans
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Brendan Gregg <bgregg@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apparently ife_meta_id2name() is only called when
CONFIG_MODULES is defined.
This fixes:
net/sched/act_ife.c:251:20: warning: ‘ife_meta_id2name’ defined but not used [-Wunused-function]
static const char *ife_meta_id2name(u32 metaid)
^~~~~~~~~~~~~~~~
Fixes: d3f24ba895f0 ("net sched actions: fix module auto-loading")
Cc: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Haiyang Zhang says:
====================
hv_netvsc: Add init of send table and var renames
Add initialization of send indirection table. Otherwise it may contain
old info of previous device with different number of channels.
Also, did some variable renaming for easier reading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tx_table is part of the private data of kernel net_device. It is only
zero-ed out when allocating net_device.
We may recreate netvsc_device w/o recreating net_device, so the private
netdev data, including tx_table, are not zeroed. It may contain channel
numbers for the older netvsc_device.
This patch adds initialization of tx_table each time we recreate
netvsc_device.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the variable name: tx_send_table
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename this variable because it is the Receive indirection
table.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The break statement for the Macronix case is missing and will
fall through to the Winbond case and re-assign the size setting.
Fix this by adding the missing break statement. Also correctly
indent the return statements.
Detected by CoverityScan, CID#1458020 ("Missing break in switch")
Fixes: 96ac18f14a5a ("cxgb4: Add support for new flash parts")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes for the recently added new code:
* make "make -s" silent for the certs file (Arnd)
* fix missing CONFIG_ in extra certs symbol (Arnd)
* use crypto_aead_authsize() to use the proper API
and two other changes:
* remove a set-but-unused variable
* don't track HT *capability* changes, capabilities
are supposed to be constant (HT operation changes)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rahul Lakkireddy says:
====================
cxgb4: add support to get hardware debug logs via ethtool
This series of patches add support to collect hardware debug logs
via ethtool --get-dump facility.
Currently supports:
Memory dumps - Collects on-chip EDC0 and EDC1 dumps.
Hardware dumps - Collects firmware and hardware dumps.
Patch 1 adds ethtool set/get dump data. It also adds template header
that precedes dump data. This template header gives additional
information needed for extracting and decoding the collected dump
data.
Patch 2 adds base to collect dumps. Also collects regdump.
Patch 3 collects on-chip EDC0 and EDC1 memory dumps.
Patch 4 collects firmware mbox log and device log.
Patch 5 updates base API for accessing TP indirect registers.
Patch 6 collects hardware TP module dump.
Patch 7 collects hardware SGE, PCIE, PM, UP CIM, MA, and HMA
module dumps.
Patch 8 collects hardware IBQ and OBQ dump.
Thanks,
Rahul
---
v2:
- Prefix symbols that pollute global namespace in files starting
with cxgb4_* with "cxgb4_"
- Prefix symbols that pollute global namespace in files starting
with cudbg_* with "cudbg_"
- Make cudbg_collect_mem_info() static.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect SGE, PCIE, PM, UP CIM, MA and HMA dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Try to access TP indirect registers via firmware first. If this fails,
fallback and access them directly. This ensures that driver and
firmware do not conflict each other while accessing the TP indirect
registers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect firmware mbox and device logs before collecting the rest of
the hardware dumps to snap the firmware state before the mailbox logs
are updated by other hardware dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect EDC0 and EDC1 memory dump.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add base to collect dump entities. Collect register dump and
update template header accordingly.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement operations to set/get dump data via ethtool. Also add
template header that precedes dump data, which helps in decoding
and extracting the dump data.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Today's -next build encountered an error due to a missing definition of
WARN_ON(), caused by some header reorganization removing an implicit
inclusion of linux/bug.h. Fix this with an explicit inclusion.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vivien Didelot says:
====================
net: dsa: remove .set_addr
An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.
If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch.
This won't make sense anymore in a multi-CPU ports system, because there
won't be a unique master device assigned to a switch tree.
Moreover this operation is confusing because it makes the user think
that it could be used to program the switch with the MAC address of the
CPU/management port such that MAC address learning can be disabled on
said port, but in fact, that's not how it is currently used.
To fix this, assign a random MAC address at setup time in the mv88e6060
and mv88e6xxx drivers before removing .set_addr completely from DSA.
Changes in v3:
- include fix for mv88e6060 switch MAC address setter.
Changes in v2:
- remove .set_addr implementation from drivers and use a random MAC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that there is no user for the .set_addr function, remove it from
DSA. If a switch supports this feature (like mv88e6xxx), the
implementation can be done in the driver setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .set_addr function does nothing, remove the dsa_loop implementation
before getting rid of it completely in DSA.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for mv88e6xxx, setup the switch from within the mv88e6060 driver with
a random MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".
If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.
The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.
If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch. This won't make sense
anymore in a multi-CPU ports system, because there won't be a unique
master device assigned to a switch tree.
Instead, setup the switch from within the Marvell driver with a random
MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
