summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-12-12sfc: Add option to use a separate channel for TX completionsNeil Turton
In a bidirectional forwarding test, we find that the best performance is achieved by sending the TX completion interrupts from one NIC to a CPU which shares an L2 cache with RX completion interrupts from the other NIC. To facilitate this, add an option (through a module parameter) to create separate channels for RX and TX completion with separate IRQs when MSI-X is available. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Restore phy_flash_cfg module parameterBen Hutchings
This is needed for recovery in case a PHY firmware upgrade is aborted. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Work around unreliable strap pinsBen Hutchings
The SFC4000 has strap pins indicating the presence of SPI flash and/or EEPROM. These pins are also used for GPIO, and in some cases they may be read wrongly at reset. However, on production boards it must boot from one or the other device, so we can assume the boot device is present and read the board config from there. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Clean up waits for flash/EEPROM operationsBen Hutchings
Make falcon_spi_wait() ignore the write timer - it is only relevant to write commands, it only works for the device that contains VPD, and it might not be initialised properly at all. Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting its use, and make it wait up to 10 ms (not 1 ms) since buffered writes to EEPROM may take this long to complete. Make both wait functions sleep instead of busy-waiting. Replace wait for command completion at top of falcon_spi_cmd() with a single poll; no command should be running when the function starts. Correct some comments. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Make reset_workqueue driver-global rather than per-NICSteve Hodgson
Each reset is serialised by the rtnl_lock anyway, so there's no win per-NIC. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Correct interpretation of second param to ethtool phys_id()Ben Hutchings
A value of 0 means indefinite repetition (until interrupted). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Remove unneeded register writeBen Hutchings
This was only ever needed for an FPGA version of Falcon. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Change SPI lengths to type size_tBen Hutchings
Based on a patch by Andrew Morton. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Board support fixesBen Hutchings
Set dummy monitor method for unrecognised boards. Clean up board resources if efx_pci_probe_main() fails after board has been initialised. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12misdn: Fix lockdep warningKarsten Keil
use correct dynamic spinlock init function. Signed-off-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: hfcmulti: use __iomem address space modifierHannes Eder
Impact: make use of the __iomem address space modifier, and change u_char *, u_short * and u_int * to void * Fix more than 30 sparse warnings of this or similar type: drivers/isdn/hardware/mISDN/hfcmulti.c:261:31: warning: incorrect type in argument 2 (different address spaces) drivers/isdn/hardware/mISDN/hfcmulti.c:261:31: got unsigned char [usertype] * drivers/isdn/hardware/mISDN/hfcmulti.c:261:31: expected void volatile [noderef] <asn:2>*addr Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: timerdev: use __user for mISDN_read's buffer argumentHannes Eder
Fix this warning: drivers/isdn/mISDN/timerdev.c:264:11: warning: incorrect type in initializer (incompatible argument 2 (different address spaces)) drivers/isdn/mISDN/timerdev.c:264:11: expected int ( *read )( ... ) drivers/isdn/mISDN/timerdev.c:264:11: got int ( static [toplevel] *<noident> )( ... ) Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: comment out unused symbolsHannes Eder
Fix this sparse warnings: drivers/isdn/hardware/mISDN/hfcmulti.c:794: warning: 'vpm_check' defined but not used drivers/isdn/mISDN/dsp_cmx.c:1546: warning: 'dsp_start_jiffies' defined but not used Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: fix sparse warning: symbol 'id' shadows an earlier oneHannes Eder
Impact: rename function scope variable Fix this warning: drivers/isdn/mISDN/l1oip_core.c:472:8: warning: symbol 'id' shadows an earlier one drivers/isdn/mISDN/l1oip_core.c:254:14: originally declared here Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: fix sparse warning: symbol 'nskb' shadows an earlier oneHannes Eder
Impact: define first occurence of variable 'nskb' in inner most possible scope Fix this sparse warning: drivers/isdn/mISDN/dsp_core.c:746:20: warning: symbol 'nskb' shadows an earlier one drivers/isdn/mISDN/dsp_core.c:634:19: originally declared here Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: un-export symbol 'plx_lock'Hannes Eder
'plx_lock' is only used within hfcmulti.c. Fix this warning: drivers/isdn/hardware/mISDN/hfcmulti.c:176:1: warning: symbol 'plx_lock' shadows an earlier one drivers/isdn/hardware/mISDN/hfcmulti.c:175:19: originally declared here Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: make global symbols static or include header filesHannes Eder
The warnings fixed by including an header file for the appropriate prototype are marked with "*", for all others the corresonponding symbol has been made static. This patch fixes all such issues in mISDN. Fix this sparse warnings: drivers/isdn/hardware/mISDN/hfcmulti.c:174:5: warning: symbol 'plxsd_master' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:426:1: warning: symbol 'write_fifo_regio' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:447:1: warning: symbol 'write_fifo_pcimem' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:469:1: warning: symbol 'read_fifo_regio' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:491:1: warning: symbol 'read_fifo_pcimem' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:710:1: warning: symbol 'vpm_init' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:793:1: warning: symbol 'vpm_check' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:816:1: warning: symbol 'vpm_echocan_on' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcmulti.c:848:1: warning: symbol 'vpm_echocan_off' was not declared. Should it be static? * drivers/isdn/mISDN/l1oip_codec.c:224:1: warning: symbol 'l1oip_law_to_4bit' was not declared. Should it be static? * drivers/isdn/mISDN/l1oip_codec.c:261:1: warning: symbol 'l1oip_4bit_to_law' was not declared. Should it be static? * drivers/isdn/mISDN/l1oip_codec.c:281:1: warning: symbol 'l1oip_alaw_to_ulaw' was not declared. Should it be static? * drivers/isdn/mISDN/l1oip_codec.c:294:1: warning: symbol 'l1oip_ulaw_to_alaw' was not declared. Should it be static? * drivers/isdn/mISDN/l1oip_codec.c:311:1: warning: symbol 'l1oip_4bit_free' was not declared. Should it be static? * drivers/isdn/mISDN/l1oip_codec.c:322:1: warning: symbol 'l1oip_4bit_alloc' was not declared. Should it be static? drivers/isdn/mISDN/core.c:29:1: warning: symbol 'device_lock' was not declared. Should it be static? drivers/isdn/mISDN/core.c:34:1: warning: symbol 'bp_lock' was not declared. Should it be static? drivers/isdn/mISDN/core.c:196:1: warning: symbol 'mISDNInit' was not declared. Should it be static? drivers/isdn/mISDN/core.c:227:6: warning: symbol 'mISDN_cleanup' was not declared. Should it be static? drivers/isdn/mISDN/stack.c:40:1: warning: symbol 'mISDN_queue_message' was not declared. Should it be static? * drivers/isdn/mISDN/layer1.c:388:1: warning: symbol 'l1_init' was not declared. Should it be static? * drivers/isdn/mISDN/layer1.c:400:1: warning: symbol 'l1_cleanup' was not declared. Should it be static? drivers/isdn/mISDN/layer2.c:469:1: warning: symbol 'iframe_error' was not declared. Should it be static? drivers/isdn/mISDN/layer2.c:487:1: warning: symbol 'super_error' was not declared. Should it be static? drivers/isdn/mISDN/layer2.c:496:1: warning: symbol 'unnum_error' was not declared. Should it be static? drivers/isdn/mISDN/layer2.c:509:1: warning: symbol 'UI_error' was not declared. Should it be static? drivers/isdn/mISDN/layer2.c:522:1: warning: symbol 'FRMR_error' was not declared. Should it be static? drivers/isdn/mISDN/layer2.c:1069:1: warning: symbol 'enquiry_cr' was not declared. Should it be static? * drivers/isdn/mISDN/layer2.c:2196:1: warning: symbol 'Isdnl2_Init' was not declared. Should it be static? * drivers/isdn/mISDN/layer2.c:2210:1: warning: symbol 'Isdnl2_cleanup' was not declared. Should it be static? drivers/isdn/mISDN/tei.c:397:1: warning: symbol 'random_ri' was not declared. Should it be static? * drivers/isdn/mISDN/timerdev.c:277:1: warning: symbol 'mISDN_inittimer' was not declared. Should it be static? * drivers/isdn/mISDN/timerdev.c:288:6: warning: symbol 'mISDN_timer_cleanup' was not declared. Should it be static? drivers/isdn/mISDN/dsp_core.c:164:12: warning: symbol 'mISDN_dsp_revision' was not declared. Should it be static? drivers/isdn/mISDN/dsp_cmx.c:1543:5: warning: symbol 'samplecount' was not declared. Should it be static? drivers/isdn/mISDN/dsp_cmx.c:1546:5: warning: symbol 'dsp_start_jiffies' was not declared. Should it be static? drivers/isdn/mISDN/dsp_cmx.c:1547:16: warning: symbol 'dsp_start_tv' was not declared. Should it be static? drivers/isdn/mISDN/dsp_tones.c:239:3: warning: symbol 'pattern' was not declared. Should it be static? drivers/isdn/mISDN/dsp_audio.c:33:4: warning: symbol 'dsp_audio_ulaw_to_alaw' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: consistently define 'debug' as '*u_int'Hannes Eder
Impact: change data type for variable 'debug' from *int to *u_int, same for the argument type of mISDN_inittimer In "core.h" mISDN_inittimer is declared with the argument type "*u_int", make the definition in "timerdev.c" match this. This fixes also this warnings: drivers/isdn/mISDN/layer1.c:391:8: warning: incorrect type in assignment (different signedness) drivers/isdn/mISDN/layer1.c:391:8: expected int *static [toplevel] debug drivers/isdn/mISDN/layer1.c:391:8: got unsigned int [usertype] *deb drivers/isdn/mISDN/layer2.c:2200:8: warning: incorrect type in assignment (different signedness) drivers/isdn/mISDN/layer2.c:2200:8: expected int *static [toplevel] debug drivers/isdn/mISDN/layer2.c:2200:8: got unsigned int [usertype] *deb drivers/isdn/mISDN/socket.c:769:8: warning: incorrect type in assignment (different signedness) drivers/isdn/mISDN/socket.c:769:8: expected int *static [toplevel] debug drivers/isdn/mISDN/socket.c:769:8: got unsigned int [usertype] *deb Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12mISDN: use NULL pointer instead of plain integerHannes Eder
Fix more than 100 (all remaining in mISDN) sparse warnings: drivers/isdn/hardware/mISDN/hfcmulti.c:***:**: warning: Using plain integer as NULL pointer drivers/isdn/mISDN/dsp_tones.c:***:**: warning: Using plain integer as NULL pointer drivers/isdn/mISDN/dsp_pipeline.c:***:**: warning: Using plain integer as NULL pointer Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-11net: Add support for the KS8695 ethernet devices.Daniel Silverstone
Implements the KS8695 ethernet device (ks8695net). This driver is only of use on the KS8695 which is an ARM9 based SoC. The documentation on this SoC is sparse and poor, with barely a register description and a rough outline of how the ethernet works, this driver was therefore written with strong reference to the Micrel supplied Linux 2.6.9 port, and to Andrew Victor's ks8695eth driver. Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk> Signed-off-by: Vincent Sanders <vince@simtec.co.uk> Acked-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-11tc35815: Enable StripCRC featureAtsushi Nemoto
The chip can strip CRC automatically on receiving. Enable it. Also fix potential RX_BUF_SIZE calculation bug which was obscured by alignment. And use proper symbols (NET_IP_ALIGN, ETH_FCS_LEN, etc.) instead of magic numbers. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-11smsc9420: SMSC LAN9420 10/100 PCI ethernet adapterSteve Glendinning
This patch adds a driver for the LAN9240 PCI ethernet adapter. Changes since initial submission: - debug msg_level has been changed to use standard definitions - convert to use net_device_ops Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-11igb: fixup AER with proper error handlingJeff Kirsher
Based on Peter Waskiewicz patch for ixgbe. Add error handling based on Hemminger's recommendation. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netfilter: xt_NFLOG is dependant of nfnetlink_logEric Leblond
The patch "don't call nf_log_packet in NFLOG module" make xt_NFLOG dependant of nfnetlink_log. This patch forces the dependencies to fix compilation in case only xt_NFLOG compilation was asked and modifies the help message accordingly to the change. Signed-off-by: Eric Leblond <eric@inl.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: enable namespace support in ipv6 multicast forwarding codeBenjamin Thery
This last patch makes the appropriate changes to use and propagate the network namespace where needed in IPv6 multicast forwarding code. This consists mainly in replacing all the remaining init_net occurences with current netns pointer retrieved from sockets, net devices or mfc6_caches depending on the routines' contexts. Some routines receive a new 'struct net' parameter to propagate the current netns: * ip6mr_get_route * ip6mr_cache_report * ip6mr_cache_find * ip6mr_cache_unresolved * mif6_add/mif6_delete * ip6mr_mfc_add/ip6mr_mfc_delete * ip6mr_reg_vif All the IPv6 multicast forwarding variables moved to struct netns_ipv6 by the previous patches are now referenced in the correct namespace. Changelog: ========== * Take into account the net associated to mfc6_cache when matching entries in mfc_unres_queue list. * Call mroute_clean_tables() in ip6mr_net_exit() to free memory allocated per-namespace. * Call dev_net_set() in ip6mr_reg_vif() to initialize dev->nd_net correctly. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: declare ip6mr /proc/net entries per-namespaceBenjamin Thery
Declare IPv6 multicast forwarding /proc/net entries per-namespace: /proc/net/ip6_mr_vif /proc/net/ip6_mr_cache Changelog ========= V2: * In routine ipmr_mfc_seq_idx(), only match entries belonging to current netns in mfc_unres_queue list. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: declare reg_vif_num per-namespaceBenjamin Thery
Preliminary work to make IPv6 multicast forwarding netns-aware. Declare variable 'reg_vif_num' per-namespace, moves into struct netns_ipv6. At the moment, this variable is only referenced in init_net. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: declare mroute_do_assert and mroute_do_pim per-namespaceBenjamin Thery
Preliminary work to make IPv6 multicast forwarding netns-aware. Declare IPv6 multicast forwarding variables 'mroute_do_assert' and 'mroute_do_pim' per-namespace in struct netns_ipv6. At the moment, these variables are only referenced in init_net. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: declare counter cache_resolve_queue_len per-namespaceBenjamin Thery
Preliminary work to make IPv6 multicast forwarding netns-aware. Declare variable cache_resolve_queue_len per-namespace: moves it into struct netns_ipv6. This variable counts the number of unresolved cache entries queued in the list mfc_unres_queue. This list is kept global to all netns as the number of entries per namespace is limited to 10 (hardcoded in routine ip6mr_cache_unresolved). Entries belonging to different namespaces in mfc_unres_queue will be identified by matching the mfc_net member introduced previously in struct mfc6_cache. Keeping this list global to all netns, also allows us to keep a single timer (ipmr_expire_timer) to handle their expiration. In some places cache_resolve_queue_len value was tested for arming or deleting the timer. These tests were equivalent to testing mfc_unres_queue value instead and are replaced in this patch. At the moment, cache_resolve_queue_len is only referenced in init_net. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: dynamically allocate mfc6_cache_arrayBenjamin Thery
Preliminary work to make IPv6 multicast forwarding netns-aware. Dynamically allocates IPv6 multicast forwarding cache, mfc6_cache_array, and moves it to struct netns_ipv6. At the moment, mfc6_cache_array is only referenced in init_net. Replace 'ARRAY_SIZE(mfc6_cache_array)' with mfc6_cache_array size: MFC6_LINES. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: store netns in struct mfc6_cacheBenjamin Thery
This patch stores into struct mfc6_cache the network namespace each mfc6_cache belongs to. The new member is mfc6_net. mfc6_net is assigned at cache allocation and doesn't change during the rest of the cache entry life. This will help to retrieve the current netns around the IPv6 multicast forwarding code. At the moment, all mfc6_cache are allocated in init_net. Changelog: ========== * Use write_pnet()/read_pnet() to set and get mfc6_net. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: dynamically allocates vif6_tableBenjamin Thery
Preliminary work to make IPv6 multicast forwarding netns-aware. Dynamically allocates interface table vif6_table and moves it to struct netns_ipv6, and updates MIF_EXISTS() macro. At the moment, vif6_table is only referenced in init_net. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10netns: ip6mr: allocate mroute6_socket per-namespace.Benjamin Thery
Preliminary work to make IPv6 multicast forwarding netns-aware. Make IPv6 multicast forwarding mroute6_socket per-namespace, moves it into struct netns_ipv6. At the moment, mroute6_socket is only referenced in init_net. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10net: Make staticRoel Kluin
Sparse asked whether these could be static. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10smsc911x: add dynamic bus configurationSteve Glendinning
Convert the driver to select 16-bit or 32-bit bus access at runtime, at a small performance cost. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10ixgbe: Implement PCIe AER supportPeter P Waskiewicz Jr
This patch implements the PCIe Advanced Error Reporting callbacks in ixgbe. The 82598 hardware supports AER, so we enable it. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10igb: Correctly determine pci-e function number in virtual environmentAlexander Duyck
When running in a virtual environment the ports of an 82575/6 can appear to be single function devices which is not correct. To resolve this we rely on the function number stored in the status register. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10igb: update handling of RCTL for smaller buffer sizesAlexander Duyck
As we begin to move into virtualization the use of a global value for buffer sizes becomes undesirable. This change makes it so only 256 and 512 byte buffers require use of the RCTL register. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bonding: turn all bond_parm_tbls constHolger Eitzenberger
Turn all bond_parm_tbls const. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bonding: make tbl argument to bond_parse_parm() constHolger Eitzenberger
bond_parse_parm() parses a parameter table for a particular value and is therefore not modifying the table at all. Therefore make the 2nd argument const, thus allowing to make the tables const later. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bonding: remove duplicate declarationsHolger Eitzenberger
Remove some declarations from bonding.c as they are declared in bonding.h already. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bonding: use pr_debug instead of own macrosHolger Eitzenberger
Use pr_debug() instead of own macros. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bonding: fix compile error if debug enabledHolger Eitzenberger
This is what I get if debug is enabled: drivers/net/bonding/bond_ipv6.c: In function 'bond_na_send': drivers/net/bonding/bond_ipv6.c:75: error: 'slave' undeclared (first use in this function) drivers/net/bonding/bond_ipv6.c:75: error: (Each undeclared identifier is reported only once drivers/net/bonding/bond_ipv6.c:75: error: for each function it appears in.) This patch fixes that. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bonding: use table for mode namesHolger Eitzenberger
Use a small array in bond_mode_name() for the names, thus saving some space: before text data bss dec hex filename 57736 9372 344 67452 1077c drivers/net/bonding/bonding.ko after text data bss dec hex filename 57441 9372 344 67157 10655 drivers/net/bonding/bonding.ko Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bonding: add and use bond_is_lb()Holger Eitzenberger
Introduce and use bond_is_lb(), it is usefull to shorten the repetitive check for either ALB or TLB mode. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09pkt_sched: sch_htb: Optimize WARN_ONs in htb_dequeue_tree() etc.Jarek Poplawski
We can skip WARN_ON() in htb_dequeue_tree() because there should be always a similar warning from htb_lookup_leaf() earlier. The first WARN_ON() in in htb_lookup_leaf() is changed to BUG_ON() because most likly this should end with oops anyway. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09pkt_sched: sch_htb: Optimize htb_find_next_upper()Jarek Poplawski
htb_id_find_next_upper() is usually called to find a class with next id after some previously removed class, so let's move a check for equality to the end: it's the least likely here. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09phy: Add LSI ET1011C PHY driverChaithrika U S
Adds LSI ET1011C PHY driver. This driver is used by TI DM646x EVM. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bluetooth: Fix unused var warning properly in rfcomm_sock_ioctl().David S. Miller
As Stephen Rothwell points out, we don't want 'sock' here but rather we really do want 'sk'. This local var is protected by all sorts of bluetooth debugging kconfig vars, but BT_DBG() is just a straight pr_debug() call which is unconditional. pr_debug() evaluates it's args only if either DEBUG or CONFIG_DYNAMIC_PRINTK_DEBUG is defined. Solving this inside of the BT_DBG() macro is non-trivial since it's varargs. And these ifdefs are ugly. So, just mark this 'sk' thing __maybe_unused and kill the ifdefs. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09myri10ge: check fragmentation in LRO get_frag_header()Brice Goglin
Add a fragmentation check to myri10ge's LRO get_frag_header() callback. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Andrew Gallatin <gallatin@myri.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-23 00:26:20 +0000