| Age | Commit message (Collapse) | Author |
|---|
|
In case of the st,tx-retime-src is missing from device-tree
(it's an optional field) the driver will invoke the strcasecmp to check
which clock has been selected and this is a bug; the else condition
is needed.
In the dwmac_setup, the "rs" variable, passed to the strcasecmp, was not
initialized and the compiler, depending on the options adopted, could
take it in some different part of the stack generating the hang in such
configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to fix the csr clock in case of 300MHz is provided.
Reported-by: Kent Borg <Kent.Borg@csr.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resume the HW is re-configured but some settings can be lost.
For example, the MAC Address_X High/Low Registers used for VLAN tagging..
So, while resuming, the set_filter callback needs to be invoked to
re-program perfect and hash-table registers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once TX has been enabled on a NIC, it is illegal to access skb,
as this skb might have been freed by another cpu, from TX completion
handler.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 9c7077622dd91 ("packet: make packet_snd fail on len smaller
than l2 header") added validation for the packet size in packet_snd.
This change enforces that every packet needs a header (with at least
hard_header_len bytes) plus a payload with at least one byte. Before
this change the payload was optional.
This fixes PPPoE connections which do not have a "Service" or
"Host-Uniq" configured (which is violating the spec, but is still
widely used in real-world setups). Those are currently failing with the
following message: "pppd: packet size is too short (24 <= 24)"
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when having map file descriptors pointing to program arrays,
there's still the issue that we unconditionally flush program array
contents via bpf_fd_array_map_clear() in bpf_map_release(). This happens
when such a file descriptor is released and is independent of the map's
refcount.
Having this flush independent of the refcount is for a reason: there
can be arbitrary complex dependency chains among tail calls, also circular
ones (direct or indirect, nesting limit determined during runtime), and
we need to make sure that the map drops all references to eBPF programs
it holds, so that the map's refcount can eventually drop to zero and
initiate its freeing. Btw, a walk of the whole dependency graph would
not be possible for various reasons, one being complexity and another
one inconsistency, i.e. new programs can be added to parts of the graph
at any time, so there's no guaranteed consistent state for the time of
such a walk.
Now, the program array pinning itself works, but the issue is that each
derived file descriptor on close would nevertheless call unconditionally
into bpf_fd_array_map_clear(). Instead, keep track of users and postpone
this flush until the last reference to a user is dropped. As this only
concerns a subset of references (f.e. a prog array could hold a program
that itself has reference on the prog array holding it, etc), we need to
track them separately.
Short analysis on the refcounting: on map creation time usercnt will be
one, so there's no change in behaviour for bpf_map_release(), if unpinned.
If we already fail in map_create(), we are immediately freed, and no
file descriptor has been made public yet. In bpf_obj_pin_user(), we need
to probe for a possible map in bpf_fd_probe_obj() already with a usercnt
reference, so before we drop the reference on the fd with fdput().
Therefore, if actual pinning fails, we need to drop that reference again
in bpf_any_put(), otherwise we keep holding it. When last reference
drops on the inode, the bpf_any_put() in bpf_evict_inode() will take
care of dropping the usercnt again. In the bpf_obj_get_user() case, the
bpf_any_get() will grab a reference on the usercnt, still at a time when
we have the reference on the path. Should we later on fail to grab a new
file descriptor, bpf_any_put() will drop it, otherwise we hold it until
bpf_map_release() time.
Joint work with Alexei.
Fixes: b2197755b263 ("bpf: add support for persistent maps/progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 35a4a57 ("isdn: clean up debug format string usage") introduced
a safeguard to avoid accidential format string interpolation of data
when calling debugl1 or HiSax_putstatus. This did however not take into
account VHiSax_putstatus (called by HiSax_putstatus) does *not* call
vsprintf if the head parameter is NULL - the format string is treated
as plain text then instead. As a result, the string "%s" is processed
literally, and the actual information is lost. This affects the isdnlog
userspace program which stopped logging information since that commit.
So revert the HiSax_putstatus invocations to the previous state.
Fixes: 35a4a5733b0a ("isdn: clean up debug format string usage")
Cc: Kees Cook <keescook@chromium.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sasha's found a NULL pointer dereference in the RDS connection code when
sending a message to an apparently unbound socket. The problem is caused
by the code checking if the socket is bound in rds_sendmsg(), which checks
the rs_bound_addr field without taking a lock on the socket. This opens a
race where rs_bound_addr is temporarily set but where the transport is not
in rds_bind(), leading to a NULL pointer dereference when trying to
dereference 'trans' in __rds_conn_create().
Vegard wrote a reproducer for this issue, so kindly ask him to share if
you're interested.
I cannot reproduce the NULL pointer dereference using Vegard's reproducer
with this patch, whereas I could without.
Complete earlier incomplete fix to CVE-2015-6937:
74e98eb08588 ("RDS: verify the underlying transport exists before creating a connection")
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Reviewed-by: Vegard Nossum <vegard.nossum@oracle.com>
Reviewed-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During pre-upstream development, the openvswitch datapath used a custom
hashtable to store vports that could fail on delete due to lack of
memory. However, prior to upstream submission, this code was reworked to
use an hlist based hastable with flexible-array based buckets. As such
the failure condition was eliminated from the vport_del path, rendering
this comment invalid.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since (at least) commit b17a7c179dd3 ("[NET]: Do sysfs registration as
part of register_netdevice."), netdev_run_todo() deals only with
unregistration, so we don't need to do the rtnl_unlock/lock cycle to
finish registration when failing pimreg or dvmrp device creation. In
fact that opens a race condition where someone can delete the device
while rtnl is unlocked because it's fully registered. The problem gets
worse when netlink support is introduced as there are more points of entry
that can cause it and it also makes reusing that code correctly impossible.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Normally, the transmit phase of a client call is implicitly ack'd by the
reception of the first data packet of the response being received.
However, if a security negotiation happens, the transmit phase, if it is
entirely contained in a single packet, may get an ack packet in response
and then may get aborted due to security negotiation failure.
Because the client has shifted state to RXRPC_CALL_CLIENT_AWAIT_REPLY due
to having transmitted all the data, the code that handles processing of the
received ack packet doesn't note the hard ack the data packet.
The following abort packet in the case of security negotiation failure then
incurs an assertion failure when it tries to drain the Tx queue because the
hard ack state is out of sync (hard ack means the packets have been
processed and can be discarded by the sender; a soft ack means that the
packets are received but could still be discarded and rerequested by the
receiver).
To fix this, we should record the hard ack we received for the ack packet.
The assertion failure looks like:
RxRPC: Assertion failed
1 <= 0 is false
0x1 <= 0x0 is false
------------[ cut here ]------------
kernel BUG at ../net/rxrpc/ar-ack.c:431!
...
RIP: 0010:[<ffffffffa006857b>] [<ffffffffa006857b>] rxrpc_rotate_tx_window+0xbc/0x131 [af_rxrpc]
...
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a fragmented multicast packet is received on an ethernet device which
has an active macvlan on top of it, each fragment is duplicated and
received both on the underlying device and the macvlan. If some
fragments for macvlan are processed before the whole packet for the
underlying device is reassembled, the "overlapping fragments" test in
ip6_frag_queue() discards the whole fragment queue.
To resolve this, add device ifindex to the search key and require it to
match reassembling multicast packets and packets to link-local
addresses.
Note: similar patch has been already submitted by Yoshifuji Hideaki in
http://patchwork.ozlabs.org/patch/220979/
but got lost and forgotten for some reason.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixing kernel crash when doing ifconfig down and up in a loop,
[ 124.028237] Call trace:
[ 124.030670] [<ffffffc000367ce0>] memcpy+0x20/0x180
[ 124.035436] [<ffffffc00053c250>] skb_clone+0x3c/0xa8
[ 124.040374] [<ffffffc00053ffa4>] __skb_tstamp_tx+0xc0/0x118
[ 124.045918] [<ffffffc00054000c>] skb_tstamp_tx+0x10/0x1c
[ 124.051203] [<ffffffc00049bc84>] xgene_enet_start_xmit+0x2e4/0x33c
[ 124.057352] [<ffffffc00054fc20>] dev_hard_start_xmit+0x2e8/0x400
[ 124.063327] [<ffffffc00056cb14>] sch_direct_xmit+0x90/0x1d4
[ 124.068870] [<ffffffc000550100>] __dev_queue_xmit+0x28c/0x498
[ 124.074585] [<ffffffc00055031c>] dev_queue_xmit_sk+0x10/0x1c
[ 124.080216] [<ffffffc0005c3f14>] ip_finish_output2+0x3d0/0x438
[ 124.086017] [<ffffffc0005c5794>] ip_finish_output+0x198/0x1ac
[ 124.091732] [<ffffffc0005c61d4>] ip_output+0xec/0x164
[ 124.096755] [<ffffffc0005c5910>] ip_local_out_sk+0x38/0x48
[ 124.102211] [<ffffffc0005c5d84>] ip_queue_xmit+0x288/0x330
[ 124.107668] [<ffffffc0005da8bc>] tcp_transmit_skb+0x908/0x964
[ 124.113383] [<ffffffc0005dc0d4>] tcp_send_ack+0x128/0x138
[ 124.118753] [<ffffffc0005d1580>] __tcp_ack_snd_check+0x5c/0x94
[ 124.124555] [<ffffffc0005d7a0c>] tcp_rcv_established+0x554/0x68c
[ 124.130530] [<ffffffc0005df0d4>] tcp_v4_do_rcv+0xa4/0x37c
[ 124.135900] [<ffffffc000539430>] release_sock+0xb4/0x150
[ 124.141184] [<ffffffc0005cdf88>] tcp_recvmsg+0x448/0x9e0
[ 124.146468] [<ffffffc0005f2f3c>] inet_recvmsg+0xa0/0xc0
[ 124.151666] [<ffffffc000533660>] sock_recvmsg+0x10/0x1c
[ 124.156863] [<ffffffc0005370d4>] SyS_recvfrom+0xa4/0xf8
[ 124.162061] Code: f2400c84 540001c0 cb040042 36000064 (38401423)
[ 124.168133] ---[ end trace 7ab2550372e8a65b ]---
The fix was to reorder napi_enable, napi_disable, request_irq and
free_irq calls, move register_netdev after dma_coerce_mask_and_coherent.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Khuong Dinh <kdinh@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 77b0a099674a ("cdc-ncm: use common parser") added a dangerous
new trust in the CDC functional descriptors presented by the device,
unconditionally assuming that any device handled by the driver has
a CDC Union descriptor.
This descriptor is required by the NCM and MBIM specs, but crashing
on non-compliant devices is still unacceptable. Not only will that
allow malicious devices to crash the kernel, but in this case it is
also well known that there are non-compliant real devices on the
market - as shown by the comment accompanying the IAD workaround
in the same function.
The Sierra Wireless EM7305 is an example of such device, having
a CDC header and a CDC MBIM descriptor but no CDC Union:
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 12
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 14
bInterfaceProtocol 0
iInterface 0
CDC Header:
bcdCDC 1.10
CDC MBIM:
bcdMBIMVersion 1.00
wMaxControlMessage 4096
bNumberFilters 16
bMaxFilterSize 128
wMaxSegmentSize 4064
bmNetworkCapabilities 0x20
8-byte ntb input size
Endpoint Descriptor:
..
The conversion to a common parser also left the local cdc_union
variable untouched. This caused the IAD workaround code to be applied
to all devices with an IAD descriptor, which was never intended. Finish
the conversion by testing for hdr.usb_cdc_union_desc instead.
Cc: Oliver Neukum <oneukum@suse.com>
Fixes: 77b0a099674a ("cdc-ncm: use common parser")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-11-23
this is a pull request of three patches for the upcoming v4.4 release.
The first patch is by Mirza Krak, it fixes a problem with the sja1000 driver
after resuming from suspend to disk, by clearing all outstanding interrupts.
Oliver Hartkopp contributes two patches targeting almost all driver, they fix
the assignment of the error location in CAN error messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverity says:
*** CID 1338065: Error handling issues (CHECKED_RETURN)
/net/tipc/udp_media.c: 162 in tipc_udp_send_msg()
156 struct udp_media_addr *dst = (struct udp_media_addr *)&dest->value;
157 struct udp_media_addr *src = (struct udp_media_addr *)&b->addr.value;
158 struct sk_buff *clone;
159 struct rtable *rt;
160
161 if (skb_headroom(skb) < UDP_MIN_HEADROOM)
>>> CID 1338065: Error handling issues (CHECKED_RETURN)
>>> Calling "pskb_expand_head" without checking return value (as is done elsewhere 51 out of 56 times).
162 pskb_expand_head(skb, UDP_MIN_HEADROOM, 0, GFP_ATOMIC);
163
164 clone = skb_clone(skb, GFP_ATOMIC);
165 skb_set_inner_protocol(clone, htons(ETH_P_TIPC));
166 ub = rcu_dereference_rtnl(b->media_ptr);
167 if (!ub) {
When expanding buffer headroom over udp tunnel with pskb_expand_head(),
it's unfortunate that we don't check its return value. As a result, if
the function returns an error code due to the lack of memory, it may
cause unpredictable consequence as we unconditionally consider that
it's always successful.
Fixes: e53567948f82 ("tipc: conditionally expand buffer headroom over udp tunnel")
Reported-by: <scan-admin@coverity.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if we drain receive queue thoroughly in tipc_release() after tipc
socket is removed from rhashtable, it is possible that some packets
are in flight because some CPU runs receiver and did rhashtable lookup
before we removed socket. They will achieve receive queue, but nobody
delete them at all. To avoid this leak, we register a private socket
destructor to purge receive queue, meaning releasing packets pending
on receive queue will be delayed until the last reference of tipc
socket will be released.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit fcb26ec5b18d ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b18d ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When vrf's ->newlink is called, if register_netdevice() fails then it
does free_netdev(), but that's also done by rtnl_newlink() so a second
free happens and memory gets corrupted, to reproduce execute the
following line a couple of times (1 - 5 usually is enough):
$ for i in `seq 1 5`; do ip link add vrf: type vrf table 1; done;
This works because we fail in register_netdevice() because of the wrong
name "vrf:".
And here's a trace of one crash:
[ 28.792157] ------------[ cut here ]------------
[ 28.792407] kernel BUG at fs/namei.c:246!
[ 28.792608] invalid opcode: 0000 [#1] SMP
[ 28.793240] Modules linked in: vrf nfsd auth_rpcgss oid_registry
nfs_acl nfs lockd grace sunrpc crct10dif_pclmul crc32_pclmul
crc32c_intel qxl drm_kms_helper ttm drm aesni_intel aes_x86_64 psmouse
glue_helper lrw evdev gf128mul i2c_piix4 ablk_helper cryptd ppdev
parport_pc parport serio_raw pcspkr virtio_balloon virtio_console
i2c_core acpi_cpufreq button 9pnet_virtio 9p 9pnet fscache ipv6 autofs4
ext4 crc16 mbcache jbd2 virtio_blk virtio_net sg sr_mod cdrom
ata_generic ehci_pci uhci_hcd ehci_hcd e1000 usbcore usb_common ata_piix
libata virtio_pci virtio_ring virtio scsi_mod floppy
[ 28.796016] CPU: 0 PID: 1148 Comm: ld-linux-x86-64 Not tainted
4.4.0-rc1+ #24
[ 28.796016] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.8.1-20150318_183358- 04/01/2014
[ 28.796016] task: ffff8800352561c0 ti: ffff88003592c000 task.ti:
ffff88003592c000
[ 28.796016] RIP: 0010:[<ffffffff812187b3>] [<ffffffff812187b3>]
putname+0x43/0x60
[ 28.796016] RSP: 0018:ffff88003592fe88 EFLAGS: 00010246
[ 28.796016] RAX: 0000000000000000 RBX: ffff8800352561c0 RCX:
0000000000000001
[ 28.796016] RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffff88003784f000
[ 28.796016] RBP: ffff88003592ff08 R08: 0000000000000001 R09:
0000000000000000
[ 28.796016] R10: 0000000000000000 R11: 0000000000000001 R12:
0000000000000000
[ 28.796016] R13: 000000000000047c R14: ffff88003784f000 R15:
ffff8800358c4a00
[ 28.796016] FS: 0000000000000000(0000) GS:ffff88003fc00000(0000)
knlGS:0000000000000000
[ 28.796016] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 28.796016] CR2: 00007ffd583bc2d9 CR3: 0000000035a99000 CR4:
00000000000406f0
[ 28.796016] Stack:
[ 28.796016] ffffffff8121045d ffffffff812102d3 ffff8800352561c0
ffff880035a91660
[ 28.796016] ffff8800008a9880 0000000000000000 ffffffff81a49940
00ffffff81218684
[ 28.796016] ffff8800352561c0 000000000000047c 0000000000000000
ffff880035b36d80
[ 28.796016] Call Trace:
[ 28.796016] [<ffffffff8121045d>] ?
do_execveat_common.isra.34+0x74d/0x930
[ 28.796016] [<ffffffff812102d3>] ?
do_execveat_common.isra.34+0x5c3/0x930
[ 28.796016] [<ffffffff8121066c>] do_execve+0x2c/0x30
[ 28.796016] [<ffffffff810939a0>]
call_usermodehelper_exec_async+0xf0/0x140
[ 28.796016] [<ffffffff810938b0>] ? umh_complete+0x40/0x40
[ 28.796016] [<ffffffff815cb1af>] ret_from_fork+0x3f/0x70
[ 28.796016] Code: 48 8d 47 1c 48 89 e5 53 48 8b 37 48 89 fb 48 39 c6
74 1a 48 8b 3d 7e e9 8f 00 e8 49 fa fc ff 48 89 df e8 f1 01 fd ff 5b 5d
f3 c3 <0f> 0b 48 89 fe 48 8b 3d 61 e9 8f 00 e8 2c fa fc ff 5b 5d eb e9
[ 28.796016] RIP [<ffffffff812187b3>] putname+0x43/0x60
[ 28.796016] RSP <ffff88003592fe88>
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARN_ON_ONCE() takes a condition, it doesn't take an error message. I
have converted this to WARN() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rainer Weikusat <rweikusat@mobileactivedefense.com> writes:
An AF_UNIX datagram socket being the client in an n:1 association with
some server socket is only allowed to send messages to the server if the
receive queue of this socket contains at most sk_max_ack_backlog
datagrams. This implies that prospective writers might be forced to go
to sleep despite none of the message presently enqueued on the server
receive queue were sent by them. In order to ensure that these will be
woken up once space becomes again available, the present unix_dgram_poll
routine does a second sock_poll_wait call with the peer_wait wait queue
of the server socket as queue argument (unix_dgram_recvmsg does a wake
up on this queue after a datagram was received). This is inherently
problematic because the server socket is only guaranteed to remain alive
for as long as the client still holds a reference to it. In case the
connection is dissolved via connect or by the dead peer detection logic
in unix_dgram_sendmsg, the server socket may be freed despite "the
polling mechanism" (in particular, epoll) still has a pointer to the
corresponding peer_wait queue. There's no way to forcibly deregister a
wait queue with epoll.
Based on an idea by Jason Baron, the patch below changes the code such
that a wait_queue_t belonging to the client socket is enqueued on the
peer_wait queue of the server whenever the peer receive queue full
condition is detected by either a sendmsg or a poll. A wake up on the
peer queue is then relayed to the ordinary wait queue of the client
socket via wake function. The connection to the peer wait queue is again
dissolved if either a wake up is about to be relayed or the client
socket reconnects or a dead peer is detected or the client socket is
itself closed. This enables removing the second sock_poll_wait from
unix_dgram_poll, thus avoiding the use-after-free, while still ensuring
that no blocked writer sleeps forever.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Fixes: ec0d215f9420 ("af_unix: fix 'poll for write'/connected DGRAM sockets")
Reviewed-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The classid of a process is changed either when a process is moved to
or from a cgroup or when the net_cls.classid file is updated.
Previously net_cls only supported propogating these changes to the
cgroup's related sockets when a process was added or removed from the
cgroup. This means it was neccessary to remove and re-add all processes
to a cgroup in order to update its classid. This change introduces
support for doing this dynamically - i.e. when the value is changed in
the net_cls_classid file, this will also trigger an update to the
classid associated with all sockets controlled by the cgroup.
This mimics the behaviour of other cgroup subsystems.
net_prio circumvents this issue by storing an index into a table with
each socket (and so any updates to the table, don't require updating
the value associated with the socket). net_cls, however, passes the
socket the classid directly, and so this additional step is needed.
Signed-off-by: Nina Schiff <ninasc@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Freescale hosts some ARMv8 based SoCs, and a generic convention
ARCH_LAYERSCAPE is used to cover such SoCs. Adding ARCH_LAYERSCAPE
to dependencies of NET_VENDOR_FREESCALE to support networking on those
SoCs.
The ARCH_LAYERSCAPE is introduced by:
commit: 53a5fde05 arm64: Use generic Layerscape SoC family naming
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.
So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.
This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.
Fixes: 8229efdaef1e ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code")
CC: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When destroying an mrt table the static mfc entries and the static
devices are kept, which leads to devices that can never be destroyed
(because of refcnt taken) and leaked memory, for example:
unreferenced object 0xffff880034c144c0 (size 192):
comm "mfc-broken", pid 4777, jiffies 4320349055 (age 46001.964s)
hex dump (first 32 bytes):
98 53 f0 34 00 88 ff ff 98 53 f0 34 00 88 ff ff .S.4.....S.4....
ef 0a 0a 14 01 02 03 04 00 00 00 00 01 00 00 00 ................
backtrace:
[<ffffffff815c1b9e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811ea6e0>] kmem_cache_alloc+0x190/0x300
[<ffffffff815931cb>] ip_mroute_setsockopt+0x5cb/0x910
[<ffffffff8153d575>] do_ip_setsockopt.isra.11+0x105/0xff0
[<ffffffff8153e490>] ip_setsockopt+0x30/0xa0
[<ffffffff81564e13>] raw_setsockopt+0x33/0x90
[<ffffffff814d1e14>] sock_common_setsockopt+0x14/0x20
[<ffffffff814d0b51>] SyS_setsockopt+0x71/0xc0
[<ffffffff815cdbf6>] entry_SYSCALL_64_fastpath+0x16/0x7a
[<ffffffffffffffff>] 0xffffffffffffffff
Make sure that everything is cleaned on netns destruction.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi
* bump API to firmware 19 - not released yet.
* fix D3 flows (Luca)
* new device IDs (Oren)
* fix NULL pointer dereference (Avri)
ath10k
* fix invalid NSS for 4x4 devices
* add QCA9377 hw1.0 support
* fix QCA6174 regression with CE5 usage
wil6210
* new maintainer - Maya Erez
rtlwifi
* rtl8821ae: Fix lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I haven't had any PCI tulip HW for the past ~5 years. I have
been reviewing tulip patches and can continue doing that.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David and HacKurx reported a following/similar size overflow triggered
in a grsecurity kernel, thanks to PaX's gcc size overflow plugin:
(Already fixed in later grsecurity versions by Brad and PaX Team.)
[ 1002.296137] PAX: size overflow detected in function scm_detach_fds net/core/scm.c:314
cicus.202_127 min, count: 4, decl: msg_controllen; num: 0; context: msghdr;
[ 1002.296145] CPU: 0 PID: 3685 Comm: scm_rights_recv Not tainted 4.2.3-grsec+ #7
[ 1002.296149] Hardware name: Apple Inc. MacBookAir5,1/Mac-66F35F19FE2A0D05, [...]
[ 1002.296153] ffffffff81c27366 0000000000000000 ffffffff81c27375 ffffc90007843aa8
[ 1002.296162] ffffffff818129ba 0000000000000000 ffffffff81c27366 ffffc90007843ad8
[ 1002.296169] ffffffff8121f838 fffffffffffffffc fffffffffffffffc ffffc90007843e60
[ 1002.296176] Call Trace:
[ 1002.296190] [<ffffffff818129ba>] dump_stack+0x45/0x57
[ 1002.296200] [<ffffffff8121f838>] report_size_overflow+0x38/0x60
[ 1002.296209] [<ffffffff816a979e>] scm_detach_fds+0x2ce/0x300
[ 1002.296220] [<ffffffff81791899>] unix_stream_read_generic+0x609/0x930
[ 1002.296228] [<ffffffff81791c9f>] unix_stream_recvmsg+0x4f/0x60
[ 1002.296236] [<ffffffff8178dc00>] ? unix_set_peek_off+0x50/0x50
[ 1002.296243] [<ffffffff8168fac7>] sock_recvmsg+0x47/0x60
[ 1002.296248] [<ffffffff81691522>] ___sys_recvmsg+0xe2/0x1e0
[ 1002.296257] [<ffffffff81693496>] __sys_recvmsg+0x46/0x80
[ 1002.296263] [<ffffffff816934fc>] SyS_recvmsg+0x2c/0x40
[ 1002.296271] [<ffffffff8181a3ab>] entry_SYSCALL_64_fastpath+0x12/0x85
Further investigation showed that this can happen when an *odd* number of
fds are being passed over AF_UNIX sockets.
In these cases CMSG_LEN(i * sizeof(int)) and CMSG_SPACE(i * sizeof(int)),
where i is the number of successfully passed fds, differ by 4 bytes due
to the extra CMSG_ALIGN() padding in CMSG_SPACE() to an 8 byte boundary
on 64 bit. The padding is used to align subsequent cmsg headers in the
control buffer.
When the control buffer passed in from the receiver side *lacks* these 4
bytes (e.g. due to buggy/wrong API usage), then msg->msg_controllen will
overflow in scm_detach_fds():
int cmlen = CMSG_LEN(i * sizeof(int)); <--- cmlen w/o tail-padding
err = put_user(SOL_SOCKET, &cm->cmsg_level);
if (!err)
err = put_user(SCM_RIGHTS, &cm->cmsg_type);
if (!err)
err = put_user(cmlen, &cm->cmsg_len);
if (!err) {
cmlen = CMSG_SPACE(i * sizeof(int)); <--- cmlen w/ 4 byte extra tail-padding
msg->msg_control += cmlen;
msg->msg_controllen -= cmlen; <--- iff no tail-padding space here ...
} ... wrap-around
F.e. it will wrap to a length of 18446744073709551612 bytes in case the
receiver passed in msg->msg_controllen of 20 bytes, and the sender
properly transferred 1 fd to the receiver, so that its CMSG_LEN results
in 20 bytes and CMSG_SPACE in 24 bytes.
In case of MSG_CMSG_COMPAT (scm_detach_fds_compat()), I haven't seen an
issue in my tests as alignment seems always on 4 byte boundary. Same
should be in case of native 32 bit, where we end up with 4 byte boundaries
as well.
In practice, passing msg->msg_controllen of 20 to recvmsg() while receiving
a single fd would mean that on successful return, msg->msg_controllen is
being set by the kernel to 24 bytes instead, thus more than the input
buffer advertised. It could f.e. become an issue if such application later
on zeroes or copies the control buffer based on the returned msg->msg_controllen
elsewhere.
Maximum number of fds we can send is a hard upper limit SCM_MAX_FD (253).
Going over the code, it seems like msg->msg_controllen is not being read
after scm_detach_fds() in scm_recv() anymore by the kernel, good!
Relevant recvmsg() handler are unix_dgram_recvmsg() (unix_seqpacket_recvmsg())
and unix_stream_recvmsg(). Both return back to their recvmsg() caller,
and ___sys_recvmsg() places the updated length, that is, new msg_control -
old msg_control pointer into msg->msg_controllen (hence the 24 bytes seen
in the example).
Long time ago, Wei Yongjun fixed something related in commit 1ac70e7ad24a
("[NET]: Fix function put_cmsg() which may cause usr application memory
overflow").
RFC3542, section 20.2. says:
The fields shown as "XX" are possible padding, between the cmsghdr
structure and the data, and between the data and the next cmsghdr
structure, if required by the implementation. While sending an
application may or may not include padding at the end of last
ancillary data in msg_controllen and implementations must accept both
as valid. On receiving a portable application must provide space for
padding at the end of the last ancillary data as implementations may
copy out the padding at the end of the control message buffer and
include it in the received msg_controllen. When recvmsg() is called
if msg_controllen is too small for all the ancillary data items
including any trailing padding after the last item an implementation
may set MSG_CTRUNC.
Since we didn't place MSG_CTRUNC for already quite a long time, just do
the same as in 1ac70e7ad24a to avoid an overflow.
Btw, even man-page author got this wrong :/ See db939c9b26e9 ("cmsg.3: Fix
error in SCM_RIGHTS code sample"). Some people must have copied this (?),
thus it got triggered in the wild (reported several times during boot by
David and HacKurx).
No Fixes tag this time as pre 2002 (that is, pre history tree).
Reported-by: David Sterba <dave@jikos.cz>
Reported-by: HacKurx <hackurx@gmail.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 5266698661401afc5e ("tipc: let broadcast packet
reception use new link receive function") the broadcast send
link state was meant to always be set to LINK_ESTABLISHED, since
we don't need this link to follow the regular link FSM rules. It
was also the intention that this state anyway shouldn't impact
the run-time working state of the link, since the latter in
reality is controlled by the number of registered peers.
We have now discovered that this assumption is not quite correct.
If the broadcast link is reset because of too many retransmissions,
its state will inadvertently go to LINK_RESETTING, and never go
back to LINK_ESTABLISHED, because the LINK_FAILURE event was not
anticipated. This will work well once, but if it happens a second
time, the reset on a link in LINK_RESETTING has has no effect, and
neither the broadcast link nor the unicast links will go down as
they should.
Furthermore, it is confusing that the management tool shows that
this link is in UP state when that obviously isn't the case.
We now ensure that this state strictly follows the true working
state of the link. The state is set to LINK_ESTABLISHED when
the number of peers is non-zero, and to LINK_RESET otherwise.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a driver for the Aurora VLSI NB8800 Ethernet controller.
It is an almost complete rewrite of a driver originally found in
a Sigma Designs 2.6.22 tree.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tulip driver causes annoying build-time warnings for allmodconfig
builds for all recent architectures:
dec/tulip/winbond-840.c:910:2: warning: #warning Processor architecture undefined
dec/tulip/tulip_core.c:101:2: warning: #warning Processor architecture undefined!
This is the last remaining warning for arm64, and I'd like to get rid of
it. We don't really know the cache line size, architecturally it would
be at least 16 bytes, but all implementations I found have 64 or 128
bytes. Configuring tulip for 32-byte lines as we do on ARM32 seems to
be the safe but slow default, and nobody who cares about performance these
days would use a tulip chip anyway, so we can just use that.
To save the next person the job of trying to find out what this is for
and picking a default for their architecture just to kill off the warning,
I'm now removing the preprocessor #warning and turning it into a pr_warn
or dev_warn that prints the equivalent information when the driver gets
loaded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commmit ac7eccd4d48fc "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_send_rcvq() is used for re-injecting data into tcp receive queue.
Problems :
- No check against size is performed, allowed user to fool kernel in
attempting very large memory allocations, eventually triggering
OOM when memory is fragmented.
- In case of fault during the copy we do not return correct errno.
Lets use alloc_skb_with_frags() to cook optimal skbs.
Fixes: 292e8d8c8538 ("tcp: Move rcvq sending to tcp_input.c")
Fixes: c0e88ff0f256 ("tcp: Repair socket queues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix incrementing TCPFastOpenActiveFailed snmp stats multiple times
when the handshake experiences multiple SYN timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some middle-boxes black-hole the data after the Fast Open handshake
(https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf).
The exact reason is unknown. The work-around is to disable Fast Open
temporarily after multiple recurring timeouts with few or no data
delivered in the established state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b6745f6e4e63 ("drivers: net: cpsw: davinci_emac: move reading mac
id to common file") started using of_machine_is_compatible for detecting
type but missed at dm8148 causing Ethernet to stop working.
Let's fix the issue by adding handling for dm814x.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mugunthnan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a passive TCP is created, we eventually call tcp_md5_do_add()
with sk pointing to the child. It is not owner by the user yet (we
will add this socket into listener accept queue a bit later anyway)
But we do own the spinlock, so amend the lockdep annotation to avoid
following splat :
[ 8451.090932] net/ipv4/tcp_ipv4.c:923 suspicious rcu_dereference_protected() usage!
[ 8451.090932]
[ 8451.090932] other info that might help us debug this:
[ 8451.090932]
[ 8451.090934]
[ 8451.090934] rcu_scheduler_active = 1, debug_locks = 1
[ 8451.090936] 3 locks held by socket_sockopt_/214795:
[ 8451.090936] #0: (rcu_read_lock){.+.+..}, at: [<ffffffff855c6ac1>] __netif_receive_skb_core+0x151/0xe90
[ 8451.090947] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff85618143>] ip_local_deliver_finish+0x43/0x2b0
[ 8451.090952] #2: (slock-AF_INET){+.-...}, at: [<ffffffff855acda5>] sk_clone_lock+0x1c5/0x500
[ 8451.090958]
[ 8451.090958] stack backtrace:
[ 8451.090960] CPU: 7 PID: 214795 Comm: socket_sockopt_
[ 8451.091215] Call Trace:
[ 8451.091216] <IRQ> [<ffffffff856fb29c>] dump_stack+0x55/0x76
[ 8451.091229] [<ffffffff85123b5b>] lockdep_rcu_suspicious+0xeb/0x110
[ 8451.091235] [<ffffffff8564544f>] tcp_md5_do_add+0x1bf/0x1e0
[ 8451.091239] [<ffffffff85645751>] tcp_v4_syn_recv_sock+0x1f1/0x4c0
[ 8451.091242] [<ffffffff85642b27>] ? tcp_v4_md5_hash_skb+0x167/0x190
[ 8451.091246] [<ffffffff85647c78>] tcp_check_req+0x3c8/0x500
[ 8451.091249] [<ffffffff856451ae>] ? tcp_v4_inbound_md5_hash+0x11e/0x190
[ 8451.091253] [<ffffffff85647170>] tcp_v4_rcv+0x3c0/0x9f0
[ 8451.091256] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091260] [<ffffffff856181b6>] ip_local_deliver_finish+0xb6/0x2b0
[ 8451.091263] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091267] [<ffffffff85618d38>] ip_local_deliver+0x48/0x80
[ 8451.091270] [<ffffffff85618510>] ip_rcv_finish+0x160/0x700
[ 8451.091273] [<ffffffff8561900e>] ip_rcv+0x29e/0x3d0
[ 8451.091277] [<ffffffff855c74b7>] __netif_receive_skb_core+0xb47/0xe90
Fixes: a8afca0329988 ("tcp: md5: protects md5sig_info with RCU")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During code review, I noticed we were passing a bad buffer pointer
to bpf_load_pointer helper function called by jitted code.
Point to the buffer allocated by JIT, so we don't silently corrupt
other parts of the stack.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the R8A7795 support was added to the driver, little attention was paid
to the ravb_open() error path: free_irq() for the EMAC interrupt was called
uncoditionally, unlike request_irq(), and in a wrong order as well...
As a result, on the R-Car gen2 SoCs I started getting the following in case
of a device opening error:
WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1448 __free_irq+0x8c/0x228()
Trying to free already-free IRQ 0
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc1-dirty #1005
Hardware name: Generic R8A7791 (Flattened Device Tree)
Backtrace:
[<c0013818>] (dump_backtrace) from [<c00139b4>] (show_stack+0x18/0x1c)
r6:c063cdd6 r5:00000009 r4:00000000 r3:00204140
[<c001399c>] (show_stack) from [<c022a578>] (dump_stack+0x74/0x90)
[<c022a504>] (dump_stack) from [<c0025f04>] (warn_slowpath_common+0x8c/0xb8)
r4:ef04fd38 r3:c0714770
[<c0025e78>] (warn_slowpath_common) from [<c0025fd4>] (warn_slowpath_fmt+0x38/0x40)
r8:ee8ad800 r7:ef0030a0 r6:00000000 r5:00000000 r4:ef003040
[<c0025fa0>] (warn_slowpath_fmt) from [<c0064cc0>] (__free_irq+0x8c/0x228)
r3:00000000 r2:c063ce9f
[<c0064c34>] (__free_irq) from [<c0064ecc>] (free_irq+0x70/0xa4)
r10:0000016b r8:00000000 r7:00000000 r6:ee8ad800 r5:00000000 r4:ef003040
[<c0064e5c>] (free_irq) from [<c033472c>] (ravb_open+0x224/0x274)
r7:fffffffe r6:00000000 r5:fffffffe r4:ee8ad800
[<c0334508>] (ravb_open) from [<c041ac78>] (__dev_open+0x84/0x104)
r7:ee8ad830 r6:c0566334 r5:00000000 r4:ee8ad800
[<c041abf4>] (__dev_open) from [<c041af08>] (__dev_change_flags+0x94/0x13c)
r7:00001002 r6:00000001 r5:00001003 r4:ee8ad800
[<c041ae74>] (__dev_change_flags) from [<c041afe8>] (dev_change_flags+0x20/0x50)
r7:c072e6e0 r6:00000138 r5:00001002 r4:ee8ad800
[<c041afc8>] (dev_change_flags) from [<c06ec06c>] (ip_auto_config+0x174/0xfb8)
r8:00001002 r7:c072e6e0 r6:c0703344 r5:00000001 r4:ee8ad800 r3:00000101
[<c06ebef8>] (ip_auto_config) from [<c000a810>] (do_one_initcall+0x100/0x1cc)
r10:c06fb83c r9:00000000 r8:c06ebef8 r7:c0736000 r6:c0710918 r5:c0710918
r4:ef2f8f80
[<c000a710>] (do_one_initcall) from [<c06ccddc>] (kernel_init_freeable+0x11c/0x1
ec)
r10:c06fb83c r9:00000000 r8:0000009a r7:c0736000 r6:c0706bf0 r5:c06fb834
r4:00000007
[<c06cccc0>] (kernel_init_freeable) from [<c0514c54>] (kernel_init+0x14/0xec)
r10:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0514c40 r4:c0736000
[<c0514c40>] (kernel_init) from [<c0010458>] (ret_from_fork+0x14/0x3c)
r4:00000000 r3:ef04e000
Fix up the free_irq() call order and add a new label on the error path.
Fixes: 22d4df8ff3a3 ("ravb: Add support for r8a7795 SoC")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes the definition of the pointer _expiry from time_t to
time64_t. This is to handle the Y2038 problem where time_t
will overflow in the year 2038. The change is safe because
the kernel subsystems that call dns_query pass NULL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the commit cdf3464e6c6b ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
introduced percpu storage for ip6_tunnel dst cache, but while clearing
such cache it used raw_cpu_ptr to walk the per cpu entries, so cached
dst on non current cpu are not actually reset.
This patch replaces raw_cpu_ptr with per_cpu_ptr, properly cleaning
such storage.
Fixes: cdf3464e6c6b ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the PCI device ID (0xe0a1) and alx_pci_tbl entry for the
Killer E2400 Ethernet controller, modeled after the Killer E2200
controller support (0xe091) already present in the alx driver.
This patch was originally authored by Ben Pope, but it got held up by
issues in the commit message, so I'm resubmitting it on his behalf.
I've extensively used a kernel with this patch on a System76 serw9
laptop and am quite confident it works well (at least on the hardware I
have available for testing).
Note that as a favor to System76, Ubuntu has been carrying this as a
sauce patch in their 4.2 based Wily kernel, which presumably has given
it real-world testing on other E2400 equipped hardware (I don't know of
any Ubuntu kernel bugs filed about it):
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1498633
Signed-off-by: Jason Gerard DeRose <jason@system76.com>
Signed-off-by: Ben Pope <benpope81@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If alloc_netdev() failed and return NULL, then the next instruction
would dereference it. Found by Coverity.
Compile tested only. Not sure if anyone still uses this driver
(or the whole WAN subsystem).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was detected by Coverity.
The function skb_cow_head leaves skb alone on failure, so caller needs
to free.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
