summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-10-27sh: disable deprecated genirq support.Paul Mundt
Now that all of the controllers have been fixed up, we can finally select GENERIC_HARDIRQS_NO_DEPRECATED. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: update show_interrupts() for irq_data chip lookup.Paul Mundt
Presently the irq chip is found through the irq_desc, but as this is going away convert over to an irq_data lookup instead. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: intc: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh64: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh64: update for IRQ flag handling naming changes.Paul Mundt
irq_32.c was updated for the new API, while irq_64.c was overlooked. This syncs them up and gets things building again. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27rtc: rtc-rs5c313: ctrl_in/outX to __raw_read/writeX conversion.Paul Mundt
The ctrl_xxx routines are deprecated, switch over to the __raw_xxx versions. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: mach-se: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27input: hp680_ts_input: ctrl_in/outX to __raw_read/writeX conversion.Paul Mundt
The ctrl_xxx routines are deprecated, switch over to the __raw_xxx versions. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27input: jornada680_kbd: ctrl_in/outX to __raw_read/writeX conversion.Paul Mundt
The ctrl_xxx routines are deprecated, switch over to the __raw_xxx versions. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: hd64461: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: mach-x3proto: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: mach-systemh: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: imask IRQs irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: mach-microdev: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: mach-landisk: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: IPR IRQs irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: mach-dreamcast: irq_data conversion.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: maple: ctrl_in/outX to __raw_read/writeX conversion.Paul Mundt
The ctrl_xxx routines are deprecated, switch over to the __raw_xxx versions. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27cdrom: gdrom: ctrl_in/outX to __raw_read/writeX conversion.Paul Mundt
The ctrl_xxx routines are deprecated, switch over to the __raw_xxx versions. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-27sh: Fix the sparsemem disabled build.Paul Mundt
The introduction of MAX_PHYSMEM_BITS in to the initial cpuinfo struct causes a build error when sparsemem is disabled and asm/sparsemem.h is not brought in by other means. Include it explicitly. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-26sh: Switch dynamic IRQ creation to generic irq allocator.Paul Mundt
Now that the genirq code provides an IRQ bitmap of its own and the necessary API to manipulate it, there's no need to keep our own version around anymore. In the process we kill off some unused IRQ reservation code, with future users now having to tie in to the genirq API as normal. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-26sh: Tidy up genirq Kconfig bits.Paul Mundt
Now that there's a HAVE_GENERIC_HARDIRQS, switch over. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-26sh: Sanitize sparse irqThomas Gleixner
Switch over to the new allocator functions. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-26sh: Expose physical addressing mode through cpuinfo.Paul Mundt
CPUs can be in either the legacy 29-bit or 32-bit physical addressing modes. This follows the x86 approach of tracking the phys bits in cpuinfo and exposing it to userspace through procfs. This change was requested to permit kexec-tools to detect the physical addressing mode in order to determine the appropriate address mangling. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-25Merge branch 'for-next' of git://android.git.kernel.org/kernel/tegraLinus Torvalds
* 'for-next' of git://android.git.kernel.org/kernel/tegra: spi: tegra: fix error setting on timeout spi: add spi_tegra driver tegra: harmony: enable PCI Express tegra: add PCI Express support tegra: add PCI Express clocks [ARM] tegra: Add APB DMA support [ARM] tegra: Add cpufreq support [ARM] tegra: common: Update common clock init table [ARM] tegra: clock: Add dvfs support, bug fixes, and cleanups [ARM] tegra: Add support for reading fuses [ARM] tegra: gpio: Add suspend and wake support [ARM] tegra: pinmux: add safe values, move tegra2, add suspend [ARM] tegra: add suspend and mirror irqs to legacy controller [ARM] tegra: Add legacy irq support [ARM] tegra: update iomap
2010-10-25Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: Blackfin: fix inverted anomaly 05000481 logic Blackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECK Blackfin: ppi/spi/twi headers: add missing __BFP undef Blackfin: update defconfigs Blackfin: bfin_twi.h: start a common TWI header netdev: bfin_mac: push settings to platform resources
2010-10-25spi: tegra: fix error setting on timeoutErik Gilling
avoids derefencing an uninitialized pointer Change-Id: Icf528441ae481e9f6f5ddc0be32c7c217fa49701 Signed-off-by: Erik Gilling <konkers@android.com>
2010-10-25Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblazeLinus Torvalds
* 'next' of git://git.monstr.eu/linux-2.6-microblaze: (42 commits) microblaze: Fix build with make 3.82 fbdev/xilinxfb: Microblaze driver support microblaze: Support C optimized lib functions for little-endian microblaze: Separate library optimized functions microblaze: Support timer on AXI lite microblaze: Add support for little-endian Microblaze microblaze: KGDB little endian support microblaze: Add PVR for endians plus detection net: emaclite: Add support for little-endian platforms microblaze: trivial: Add comment for AXI pvr microblaze: pci-common cleanup microblaze: Support early console on uart16550 microblaze: Do not compile early console support for uartlite if is disabled microblaze: Setup early console dynamically microblaze: Rename all uartlite early printk functions microblaze: remove early printk uarlite console dependency from header microblaze: Remove additional compatible properties microblaze: Remove hardcoded asm instraction for PVR loading microblaze: Use static const char * const where possible microblaze: Define VMALLOC_START/END ...
2010-10-25Merge branch 'hwmon-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging * 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits) hwmon: lis3: Release resources in case of failure hwmon: lis3: Short explanations of platform data fields hwmon: lis3: Enhance lis3 selftest with IRQ line test hwmon: lis3: use block read to access data registers hwmon: lis3: Adjust fuzziness for 8 bit device hwmon: lis3: New parameters to platform data hwmon: lis3: restore axis enabled bits hwmon: lis3: Power on corrections hwmon: lis3: Update coordinates at polled device open hwmon: lis3: Cleanup interrupt handling hwmon: lis3: regulator control hwmon: lis3: pm_runtime support Kirkwood: add fan support for Network Space Max v2 hwmon: add generic GPIO fan driver hwmon: (coretemp) fix reading of microcode revision (v2) hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs hwmon: (pkgtemp) align driver initialization style with coretemp hwmon: LTC4261 Hardware monitoring driver hwmon: (lis3) add axes module parameter for custom axis-mapping hwmon: (hp_accel) Add HP Mini 510x family support ...
2010-10-25MN10300: Fix the PERCPU() alignment to allow for workqueuesDavid Howells
In the MN10300 arch, we occasionally see an assertion being tripped in alloc_cwqs() at the following line: /* just in case, make sure it's actually aligned */ ---> BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align)); return wq->cpu_wq.v ? 0 : -ENOMEM; The values are: wa->cpu_wq.v => 0x902776e0 align => 0x100 and align is calculated by the following: const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS, __alignof__(unsigned long long)); This is because the pointer in question (wq->cpu_wq.v) loses some of its lower bits to control flags, and so the object it points to must be sufficiently aligned to avoid the need to use those bits for pointing to things. Currently, 4 control bits and 4 colour bits are used in normal circumstances, plus a debugging bit if debugging is set. This requires the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512 bytes aligned with debugging). PERCPU() alignment on MN13000, however, is only 32 bytes as set in vmlinux.lds.S. So we set this to PAGE_SIZE (4096) to match most other arches and stick a comment in alloc_cwqs() for anyone else who triggers the assertion. Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Mark Salter <msalter@redhat.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-10-25hwmon: lis3: Release resources in case of failureSamu Onkalo
If lis3lv02d_init_device fails, HW resources were not released properly. In case of failure call release_resources if available. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25Blackfin: fix inverted anomaly 05000481 logicMike Frysinger
No one uses these MMRs so we didn't notice when the anomaly handling logic was inverted. Reported-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-25Blackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECKMike Frysinger
This code was useful during early port development when our icache code wasn't solid, but that ship has sailed long ago, and no code calls this function anymore (irq_panic). So punt it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-25hwmon: lis3: Short explanations of platform data fieldsSamu Onkalo
Short documentation at kernel doc format. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: Enhance lis3 selftest with IRQ line testSamu Onkalo
Configure chip to data ready mode in selftest and count received interrupts to see that interrupt line(s) are working. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: use block read to access data registersSamu Onkalo
Add optional blockread function to interface driver. If available the chip driver uses it for data register access. For 12 bit device it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out 5 bytes since every second byte is dummy. This optimizes bus usage and reduces number of operations and interrupts needed for one data update. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: Adjust fuzziness for 8 bit deviceSamu Onkalo
Default fuziness is set smaller for 8 device. In 12 bit device LSB is quite close to 1 mg (mg = 1 / 1000 of earth gravity). In 8bit device LSB is about 18 mg. Set fuziness to 1 for 8 bit device. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: New parameters to platform dataSamu Onkalo
Added default output data rate setting to platform data. If default rate is 0, reset default value is used. Added control for duration via platform data. Added possibility to configure interrupts to trig on both rising and falling edge. The lis3 WU unit can be configured quite many ways and with some configurations it is quite handy to get coordinate refresh when some event trigs and when it reason goes away. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: restore axis enabled bitsSamu Onkalo
All axis enable bits are set to 0 at module remove. Restore reset default value at init. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: Power on correctionsSamu Onkalo
Sometimes lis3 chip seems to fail to setup factory tuning at boot up. This probably happens if there is some odd power ramp down ramp up sequence for example in device restart. Set boot bit in control2 register to trig boot sequence manually and wait until it is finished. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: Update coordinates at polled device openSamu Onkalo
Call input device poll function at device open to refresh coordinates immediately. This is needed for the case where poll interval is set to zero and coordinate updates happens purely under interrupt control. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: Cleanup interrupt handlingSamu Onkalo
Irqcfg moved to chip data instead of platform data. This simplifies access in interrupt handler little bit. Input device open and close functions set status for interrupt threaded handler once. Unnecessary check for interrupt source removed since it is enough that active interrupt line indicates that there was an interrupt. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: regulator controlSamu Onkalo
Based on pm_runtime control, turn lis3 regulators on and off. Perform context save and restore on transitions. Feature is optional and must be enabled in platform data. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: lis3: pm_runtime supportSamu Onkalo
Add pm_runtime support to lis3 core driver. Add pm_runtime support to lis3 i2c driver. spi and hp_accel drivers are not yet supported. Old always on functionality remains for those. For sysfs there is 5 second delay before turning off the chip to avoid long ramp up delay. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25Kirkwood: add fan support for Network Space Max v2Simon Guinot
Signed-off-by: Simon Guinot <sguinot@lacie.com> Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: add generic GPIO fan driverSimon Guinot
This patch adds hwmon support for fans connected to GPIO lines. Platform specific information such as GPIO pinout and speed conversion array (rpm from/to GPIO value) are passed to the driver via platform_data. Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: (coretemp) fix reading of microcode revision (v2)Jan Beulich
According to the documentation, simply reading the respective MSR isn't sufficient: It should be written with zeros, cpuid(1) be executed, and then read (see arch/x86/kernel/cpu/intel.c for an example). v2: Fail probe when microcode revision cannot be determined, but is needed to check for proper operation. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Chen Gong <gong.chen@linux.intel.com> Cc: Jean Delvare <khali@linux-fr.org> Acked-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefsChen Gong
CONFIG_HOTPLUG_CPU is used too much in some drivers. This patch clean them up. Signed-off-by: Chen Gong <gong.chen@linux.intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: (pkgtemp) align driver initialization style with coretempChen Gong
pkgtemp is derived from coretemp, so some reasonable logics should be applied onto pkgtemp, too. Such as the init logic here. Signed-off-by: Chen Gong <gong.chen@linux.intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-25hwmon: LTC4261 Hardware monitoring driverGuenter Roeck
This driver adds support for Linear Technology LTC4261 I2C Negative Voltage Hot Swap Controller. Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu> Reviewed-by: Tom Grennan <tom.grennan@ericsson.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-03 23:15:22 +0000