| Age | Commit message (Collapse) | Author |
|---|
|
license
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzkaller with KASAN reported an out-of-bounds read in
asn1_ber_decoder(). It can be reproduced by the following command,
assuming CONFIG_X509_CERTIFICATE_PARSER=y and CONFIG_KASAN=y:
keyctl add asymmetric desc $'\x30\x30' @s
The bug is that the length of an ASN.1 data value isn't validated in the
case where it is encoded using the short form, causing the decoder to
read past the end of the input buffer. Fix it by validating the length.
The bug report was:
BUG: KASAN: slab-out-of-bounds in asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
Read of size 1 at addr ffff88003cccfa02 by task syz-executor0/6818
CPU: 1 PID: 6818 Comm: syz-executor0 Not tainted 4.14.0-rc7-00008-g5f479447d983 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0xb3/0x10b lib/dump_stack.c:52
print_address_description+0x79/0x2a0 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x236/0x340 mm/kasan/report.c:409
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:427
asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
x509_cert_parse+0x1db/0x650 crypto/asymmetric_keys/x509_cert_parser.c:89
x509_key_preparse+0x64/0x7a0 crypto/asymmetric_keys/x509_public_key.c:174
asymmetric_key_preparse+0xcb/0x1a0 crypto/asymmetric_keys/asymmetric_type.c:388
key_create_or_update+0x347/0xb20 security/keys/key.c:855
SYSC_add_key security/keys/keyctl.c:122 [inline]
SyS_add_key+0x1cd/0x340 security/keys/keyctl.c:62
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x447c89
RSP: 002b:00007fca7a5d3bd8 EFLAGS: 00000246 ORIG_RAX: 00000000000000f8
RAX: ffffffffffffffda RBX: 00007fca7a5d46cc RCX: 0000000000447c89
RDX: 0000000020006f4a RSI: 0000000020006000 RDI: 0000000020001ff5
RBP: 0000000000000046 R08: fffffffffffffffd R09: 0000000000000000
R10: 0000000000000002 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fca7a5d49c0 R15: 00007fca7a5d4700
Fixes: 42d5ec27f873 ("X.509: Add an ASN.1 decoder")
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
When calling keyctl_read() on a key of type "trusted", if the
user-supplied buffer was too small, the kernel ignored the buffer length
and just wrote past the end of the buffer, potentially corrupting
userspace memory. Fix it by instead returning the size required, as per
the documentation for keyctl_read().
We also don't even fill the buffer at all in this case, as this is
slightly easier to implement than doing a short read, and either
behavior appears to be permitted. It also makes it match the behavior
of the "encrypted" key type.
Fixes: d00a1c72f7f4 ("keys: add new trusted key-type")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v2.6.38+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Commit e645016abc80 ("KEYS: fix writing past end of user-supplied buffer
in keyring_read()") made keyring_read() stop corrupting userspace memory
when the user-supplied buffer is too small. However it also made the
return value in that case be the short buffer size rather than the size
required, yet keyctl_read() is actually documented to return the size
required. Therefore, switch it over to the documented behavior.
Note that for now we continue to have it fill the short buffer, since it
did that before (pre-v3.13) and dump_key_tree_aux() in keyutils arguably
relies on it.
Fixes: e645016abc80 ("KEYS: fix writing past end of user-supplied buffer in keyring_read()")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two one-liner fixes for your net tree,
they are:
1) Disable fast hash operations for 2-bytes length keys which is leading
to incorrect lookups in nf_tables, from Anatole Denis.
2) Reload pointer ipv4 header after ip_route_me_harder() given this may
result in use-after-free due to skbuff header reallocation, patch
from Tejaswi Tanikella.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FRA_L3MDEV is defined as U8, but is being added as a U32 attribute. On
big endian architecture, this results in the l3mdev entry not being
added to the FIB rules.
Fixes: 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Average RTT could become zero. This happened in real life at least twice.
This patch treats zero as 1us.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Lawrence Brakmo <Brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into drm-fixes
Just two small patches for stable to fix the driver failing to load on polaris
cards with harvested VCE or UVD blocks.
* 'drm-fixes-4.14' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: allow harvesting check for Polaris VCE
drm/amdgpu: return -ENOENT from uvd 6.0 early init for harvesting
|
|
Fixes init failures on Polaris cards with harvested
VCE blocks.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Fixes init failures on polaris cards with harvested UVD.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Fixes for Stable:
- Fix KBL Blank Screen (Jani)
- Fix FIFO Underrun on SNB (Maarten)
Other fixes:
- Fix GPU Hang on i915gm (Chris)
- Fix gem_tiled_pread_pwrite IGT case (Chris)
- Cancel modeset retry work during modeset clean-up (Manasi)
* tag 'drm-intel-fixes-2017-11-01' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Check incoming alignment for unfenced buffers (on i915gm)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (vma idr)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (objects)
drm/i915/edp: read edp display control registers unconditionally
drm/i915: Do not rely on wm preservation for ILK watermarks
drm/i915: Cancel the modeset retry work during modeset cleanup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull signal bugfix from Eric Biederman:
"When making the generic support for SIGEMT conditional on the presence
of SIGEMT I made a typo that causes it to fail to activate. It was
noticed comparatively quickly but the bug report just made it to me
today"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Fix name of SIGEMT in #if defined() check
|
|
Commit cc731525f26a ("signal: Remove kernel interal si_code magic")
added a check for SIGMET and NSIGEMT being defined. That SIGMET should
in fact be SIGEMT, with SIGEMT being defined in
arch/{alpha,mips,sparc}/include/uapi/asm/signal.h
This was actually pointed out by BenHutchings in a lwn.net comment
here https://lwn.net/Comments/734608/
Fixes: cc731525f26a ("signal: Remove kernel interal si_code magic")
Signed-off-by: Andrew Clayton <andrew@digital-domain.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Pull block fixes from Jens Axboe:
"A few fixes that should go into this series:
- Regression fix for ide-cd, ensuring that a request is fully
initialized. From Hongxu.
- Ditto fix for virtio_blk, from Bart.
- NVMe fix from Keith, ensuring that we set the right block size on
revalidation. If the block size changed, we'd be in trouble without
it.
- NVMe rdma fix from Sagi, fixing a potential hang while the
controller is being removed"
* 'for-linus' of git://git.kernel.dk/linux-block:
ide:ide-cd: fix kernel panic resulting from missing scsi_req_init
nvme: Fix setting logical block format when revalidating
virtio_blk: Fix an SG_IO regression
nvme-rdma: fix possible hang when issuing commands during ctrl removal
|
|
In case the object has changed tiling between calls to execbuf, we need
to check if the existing offset inside the GTT matches the new tiling
constraint. We even need to do this for "unfenced" tiled objects, where
the 3D commands use an implied fence and so the object still needs to
match the physical fence restrictions on alignment (only required for
gen2 and early gen3).
In commit 2889caa92321 ("drm/i915: Eliminate lots of iterations over
the execobjects array"), the idea was to remove the second guessing and
only set the NEEDS_MAP flag when required. However, the entire check
for an unusable offset for fencing was removed and not just the
secondary check. I.e.
/* avoid costly ping-pong once a batch bo ended up non-mappable */
if (entry->flags & __EXEC_OBJECT_NEEDS_MAP &&
!i915_vma_is_map_and_fenceable(vma))
return !only_mappable_for_reloc(entry->flags);
was entirely removed as the ping-pong between execbuf passes was fixed,
but its primary purpose in forcing unaligned unfenced access to be
rebound was forgotten.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103502
Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031103607.17836-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 1d033beb20d6d5885587a02a393b6598d766a382)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.14
A bunch of fixes here, mostly device specific ones (the biggest one
being the revert of the hotword support for rt5514), with a couple of
core fixes for potential issues with corrupted or otherwise invalid
topology files.
|
|
Pull networking fixes from David Miller:
1) Fix refcounting in xfrm_bundle_lookup() when using a dummy bundle,
from Steffen Klassert.
2) Fix crypto header handling in rx data frames in ath10k driver, from
Vasanthakumar Thiagarajan.
3) Fix use after free of qdisc when we defer tcp_chain_flush() to a
workqueue. From Cong Wang.
4) Fix double free in lapbether driver, from Pan Bian.
5) Sanitize TUNSETSNDBUF values, from Craig Gallek.
6) Fix refcounting when addrconf_permanent_addr() calls
ipv6_del_addr(). From Eric Dumazet.
7) Fix MTU probing bug in TCP that goes back to 2007, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: fix tcp_mtu_probe() vs highest_sack
ipv6: addrconf: increment ifp refcount before ipv6_del_addr()
tun/tap: sanitize TUNSETSNDBUF input
mlxsw: i2c: Fix buffer increment counter for write transaction
mlxsw: reg: Add high and low temperature thresholds
MAINTAINERS: Remove Yotam from mlxfw
MAINTAINERS: Update Yotam's E-mail
net: hns: set correct return value
net: lapbether: fix double free
bpf: remove SK_REDIRECT from UAPI
net: phy: marvell: Only configure RGMII delays when using RGMII
xfrm: Fix GSO for IPsec with GRE tunnel.
tc-testing: fix arg to ip command: -s -> -n
net_sched: remove tcf_block_put_deferred()
l2tp: hold tunnel in pppol2tp_connect()
Revert "ath10k: fix napi_poll budget overflow"
ath10k: rebuild crypto header in rx data frames
wcn36xx: Remove unnecessary rcu_read_unlock in wcn36xx_bss_info_changed
xfrm: Clear sk_dst_cache when applying per-socket policy.
xfrm: Fix xfrm_dst_cache memleak
|
|
Syzkaller with KASAN has reported a use-after-free of vma->vm_flags in
__do_page_fault() with the following reproducer:
mmap(&(0x7f0000000000/0xfff000)=nil, 0xfff000, 0x3, 0x32, 0xffffffffffffffff, 0x0)
mmap(&(0x7f0000011000/0x3000)=nil, 0x3000, 0x1, 0x32, 0xffffffffffffffff, 0x0)
r0 = userfaultfd(0x0)
ioctl$UFFDIO_API(r0, 0xc018aa3f, &(0x7f0000002000-0x18)={0xaa, 0x0, 0x0})
ioctl$UFFDIO_REGISTER(r0, 0xc020aa00, &(0x7f0000019000)={{&(0x7f0000012000/0x2000)=nil, 0x2000}, 0x1, 0x0})
r1 = gettid()
syz_open_dev$evdev(&(0x7f0000013000-0x12)="2f6465762f696e7075742f6576656e742300", 0x0, 0x0)
tkill(r1, 0x7)
The vma should be pinned by mmap_sem, but handle_userfault() might (in a
return to userspace scenario) release it and then acquire again, so when
we return to __do_page_fault() (with other result than VM_FAULT_RETRY),
the vma might be gone.
Specifically, per Andrea the scenario is
"A return to userland to repeat the page fault later with a
VM_FAULT_NOPAGE retval (potentially after handling any pending signal
during the return to userland). The return to userland is identified
whenever FAULT_FLAG_USER|FAULT_FLAG_KILLABLE are both set in
vmf->flags"
However, since commit a3c4fb7c9c2e ("x86/mm: Fix fault error path using
unsafe vma pointer") there is a vma_pkey() read of vma->vm_flags after
that point, which can thus become use-after-free. Fix this by moving
the read before calling handle_mm_fault().
Reported-by: syzbot <bot+6a5269ce759a7bb12754ed9622076dc93f65a1f6@syzkaller.appspotmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Fixes: 3c4fb7c9c2e ("x86/mm: Fix fault error path using unsafe vma pointer")
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull cifs fix from Steve French:
"smb3 file name too long fix"
* tag 'smb3-file-name-too-long-fix' of git://git.samba.org/sfrench/cifs-2.6:
cifs: check MaxPathNameComponentLength != 0 before using it
|
|
Since we split the scsi_request out of struct request, while the
standard prep_rq_fn builds 10 byte cmds, it missed to invoke
scsi_req_init() to initialize certain fields of a scsi_request
structure (.__cmd[], .cmd, .cmd_len and .sense_len but no other
members of struct scsi_request).
An example panic on virtual machines (qemu/virtualbox) to boot
from IDE cdrom:
...
[ 8.754381] Call Trace:
[ 8.755419] blk_peek_request+0x182/0x2e0
[ 8.755863] blk_fetch_request+0x1c/0x40
[ 8.756148] ? ktime_get+0x40/0xa0
[ 8.756385] do_ide_request+0x37d/0x660
[ 8.756704] ? cfq_group_service_tree_add+0x98/0xc0
[ 8.757011] ? cfq_service_tree_add+0x1e5/0x2c0
[ 8.757313] ? ktime_get+0x40/0xa0
[ 8.757544] __blk_run_queue+0x3d/0x60
[ 8.757837] queue_unplugged+0x2f/0xc0
[ 8.758088] blk_flush_plug_list+0x1f4/0x240
[ 8.758362] blk_finish_plug+0x2c/0x40
...
[ 8.770906] RIP: ide_cdrom_prep_fn+0x63/0x180 RSP: ffff92aec018bae8
[ 8.772329] ---[ end trace 6408481e551a85c9 ]---
...
Fixes: 82ed4db499b8 ("block: split scsi_request out of struct request")
Signed-off-by: Hongxu Jia <hongxu.jia@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Just like the CTO timeout calculation introduced recently, the DTO
timeout calculation was incorrect. It used "bus_hz" but, as far as I
can tell, it's supposed to use the card clock. Let's account for the
div value, which is documented as 2x the value stored in the register,
or 1 if the register is 0.
NOTE: This was likely not terribly important until commit 16a34574c6ca
("mmc: dw_mmc: remove the quirks flags") landed because "DIV" is
documented on Rockchip SoCs (the ones that used to define the quirk)
to always be 0 or 1. ...and, in fact, it's documented to only be 1
with EMMC in 8-bit DDR52 mode. Thus before the quirk was applied to
everyone it was mostly OK to ignore the DIV value.
I haven't personally observed any problems that are fixed by this
patch but I also haven't tested this anywhere with a DIV other an 0.
AKA: this problem was found simply by code inspection and I have no
failing test cases that are fixed by it. Presumably this could fix
real bugs for someone out there, though.
Fixes: 16a34574c6ca ("mmc: dw_mmc: remove the quirks flags")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
'asoc/fix/rt5514', 'asoc/fix/rt5616', 'asoc/fix/rt5659' and 'asoc/fix/rt5663' into tmp
|
|
Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.
Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.
If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.
Bad things would then happen, including infinite loops.
This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.
Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.
Fixes: a47e5a988a57 ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the (unlikely) event fixup_permanent_addr() returns a failure,
addrconf_permanent_addr() calls ipv6_del_addr() without the
mandatory call to in6_ifa_hold(), leading to a refcount error,
spotted by syzkaller :
WARNING: CPU: 1 PID: 3142 at lib/refcount.c:227 refcount_dec+0x4c/0x50
lib/refcount.c:227
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 3142 Comm: ip Not tainted 4.14.0-rc4-next-20171009+ #33
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x41c kernel/panic.c:181
__warn+0x1c4/0x1e0 kernel/panic.c:544
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:refcount_dec+0x4c/0x50 lib/refcount.c:227
RSP: 0018:ffff8801ca49e680 EFLAGS: 00010286
RAX: 000000000000002c RBX: ffff8801d07cfcdc RCX: 0000000000000000
RDX: 000000000000002c RSI: 1ffff10039493c90 RDI: ffffed0039493cc4
RBP: ffff8801ca49e688 R08: ffff8801ca49dd70 R09: 0000000000000000
R10: ffff8801ca49df58 R11: 0000000000000000 R12: 1ffff10039493cd9
R13: ffff8801ca49e6e8 R14: ffff8801ca49e7e8 R15: ffff8801d07cfcdc
__in6_ifa_put include/net/addrconf.h:369 [inline]
ipv6_del_addr+0x42b/0xb60 net/ipv6/addrconf.c:1208
addrconf_permanent_addr net/ipv6/addrconf.c:3327 [inline]
addrconf_notify+0x1c66/0x2190 net/ipv6/addrconf.c:3393
notifier_call_chain+0x136/0x2c0 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x32/0x60 net/core/dev.c:1697
call_netdevice_notifiers net/core/dev.c:1715 [inline]
__dev_notify_flags+0x15d/0x430 net/core/dev.c:6843
dev_change_flags+0xf5/0x140 net/core/dev.c:6879
do_setlink+0xa1b/0x38e0 net/core/rtnetlink.c:2113
rtnl_newlink+0xf0d/0x1a40 net/core/rtnetlink.c:2661
rtnetlink_rcv_msg+0x733/0x1090 net/core/rtnetlink.c:4301
netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2408
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4313
netlink_unicast_kernel net/netlink/af_netlink.c:1273 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1299
netlink_sendmsg+0xa4a/0xe70 net/netlink/af_netlink.c:1862
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
___sys_sendmsg+0x75b/0x8a0 net/socket.c:2049
__sys_sendmsg+0xe5/0x210 net/socket.c:2083
SYSC_sendmsg net/socket.c:2094 [inline]
SyS_sendmsg+0x2d/0x50 net/socket.c:2090
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x7fa9174d3320
RSP: 002b:00007ffe302ae9e8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffe302b2ae0 RCX: 00007fa9174d3320
RDX: 0000000000000000 RSI: 00007ffe302aea20 RDI: 0000000000000016
RBP: 0000000000000082 R08: 0000000000000000 R09: 000000000000000f
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffe302b32a0
R13: 0000000000000000 R14: 00007ffe302b2ab8 R15: 00007ffe302b32b8
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzkaller found several variants of the lockup below by setting negative
values with the TUNSETSNDBUF ioctl. This patch adds a sanity check
to both the tun and tap versions of this ioctl.
watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [repro:2389]
Modules linked in:
irq event stamp: 329692056
hardirqs last enabled at (329692055): [<ffffffff824b8381>] _raw_spin_unlock_irqrestore+0x31/0x75
hardirqs last disabled at (329692056): [<ffffffff824b9e58>] apic_timer_interrupt+0x98/0xb0
softirqs last enabled at (35659740): [<ffffffff824bc958>] __do_softirq+0x328/0x48c
softirqs last disabled at (35659731): [<ffffffff811c796c>] irq_exit+0xbc/0xd0
CPU: 0 PID: 2389 Comm: repro Not tainted 4.14.0-rc7 #23
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff880009452140 task.stack: ffff880006a20000
RIP: 0010:_raw_spin_lock_irqsave+0x11/0x80
RSP: 0018:ffff880006a27c50 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff10
RAX: ffff880009ac68d0 RBX: ffff880006a27ce0 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffff880006a27ce0 RDI: ffff880009ac6900
RBP: ffff880006a27c60 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 000000000063ff00 R12: ffff880009ac6900
R13: ffff880006a27cf8 R14: 0000000000000001 R15: ffff880006a27cf8
FS: 00007f4be4838700(0000) GS:ffff88000cc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020101000 CR3: 0000000009616000 CR4: 00000000000006f0
Call Trace:
prepare_to_wait+0x26/0xc0
sock_alloc_send_pskb+0x14e/0x270
? remove_wait_queue+0x60/0x60
tun_get_user+0x2cc/0x19d0
? __tun_get+0x60/0x1b0
tun_chr_write_iter+0x57/0x86
__vfs_write+0x156/0x1e0
vfs_write+0xf7/0x230
SyS_write+0x57/0xd0
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x7f4be4356df9
RSP: 002b:00007ffc18101c08 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f4be4356df9
RDX: 0000000000000046 RSI: 0000000020101000 RDI: 0000000000000005
RBP: 00007ffc18101c40 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000293 R12: 0000559c75f64780
R13: 00007ffc18101d30 R14: 0000000000000000 R15: 0000000000000000
Fixes: 33dccbb050bb ("tun: Limit amount of queued packets per device")
Fixes: 20d29d7a916a ("net: macvtap driver")
Signed-off-by: Craig Gallek <kraig@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It fixes a problem for the last chunk where 'chunk_size' is smaller than
MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding
previous data.
Fixes: 6882b0aee180 ("mlxsw: Introduce support for I2C bus")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
niph is not updated after pskb_expand_head changes the skb head. It
still points to the freed data, which is then used to update tot_len and
checksum. This could cause use-after-free poison crash.
Update niph, if ip_route_me_harder does not fail.
This only affects the interaction with REJECT targets and br_netfilter.
Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2017-11-01
1) Fix a memleak when a packet matches a policy
without a matching state.
2) Reset the socket cached dst_entry when inserting
a socket policy, otherwise the policy might be
ignored. From Jonathan Basseri.
3) Fix GSO for a IPsec, GRE tunnel combination.
We reset the encapsulation field at the skb
too erly, as a result GRE does not segment
GSO packets. Fix this by resetting the the
encapsulation field right before the
transformation where the inner headers get
invalid.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
belong to kernel text
This makes the changes introduced in commit 83e840c770f2c5
("powerpc64/elfv1: Only dereference function descriptor for non-text
symbols") to be specific to the kprobe subsystem.
We previously changed ppc_function_entry() to always check the provided
address to confirm if it needed to be dereferenced. This is actually
only an issue for kprobe blacklisted asm labels (through use of
_ASM_NOKPROBE_SYMBOL) and can cause other issues with ftrace. Also, the
additional checks are not really necessary for our other uses.
As such, move this check to the kprobes subsystem.
Fixes: 83e840c770f2 ("powerpc64/elfv1: Only dereference function descriptor for non-text symbols")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
symbols"
This reverts commit 83e840c770f2c5 ("powerpc64/elfv1: Only dereference
function descriptor for non-text symbols").
Chandan reported that on newer kernels, trying to enable function_graph
tracer on ppc64 (BE) locks up the system with the following trace:
Unable to handle kernel paging request for data at address 0x600000002fa30010
Faulting instruction address: 0xc0000000001f1300
Thread overran stack, or stack corrupted
Oops: Kernel access of bad area, sig: 11 [#1]
BE SMP NR_CPUS=2048 DEBUG_PAGEALLOC NUMA pSeries
Modules linked in:
CPU: 1 PID: 6586 Comm: bash Not tainted 4.14.0-rc3-00162-g6e51f1f-dirty #20
task: c000000625c07200 task.stack: c000000625c07310
NIP: c0000000001f1300 LR: c000000000121cac CTR: c000000000061af8
REGS: c000000625c088c0 TRAP: 0380 Not tainted (4.14.0-rc3-00162-g6e51f1f-dirty)
MSR: 8000000000001032 <SF,ME,IR,DR,RI> CR: 28002848 XER: 00000000
CFAR: c0000000001f1320 SOFTE: 0
...
NIP [c0000000001f1300] .__is_insn_slot_addr+0x30/0x90
LR [c000000000121cac] .kernel_text_address+0x18c/0x1c0
Call Trace:
[c000000625c08b40] [c0000000001bd040] .is_module_text_address+0x20/0x40 (unreliable)
[c000000625c08bc0] [c000000000121cac] .kernel_text_address+0x18c/0x1c0
[c000000625c08c50] [c000000000061960] .prepare_ftrace_return+0x50/0x130
[c000000625c08cf0] [c000000000061b10] .ftrace_graph_caller+0x14/0x34
[c000000625c08d60] [c000000000121b40] .kernel_text_address+0x20/0x1c0
[c000000625c08df0] [c000000000061960] .prepare_ftrace_return+0x50/0x130
...
[c000000625c0ab30] [c000000000061960] .prepare_ftrace_return+0x50/0x130
[c000000625c0abd0] [c000000000061b10] .ftrace_graph_caller+0x14/0x34
[c000000625c0ac40] [c000000000121b40] .kernel_text_address+0x20/0x1c0
[c000000625c0acd0] [c000000000061960] .prepare_ftrace_return+0x50/0x130
[c000000625c0ad70] [c000000000061b10] .ftrace_graph_caller+0x14/0x34
[c000000625c0ade0] [c000000000121b40] .kernel_text_address+0x20/0x1c0
This is because ftrace is using ppc_function_entry() for obtaining the
address of return_to_handler() in prepare_ftrace_return(). The call to
kernel_text_address() itself gets traced and we end up in a recursive
loop.
Fixes: 83e840c770f2 ("powerpc64/elfv1: Only dereference function descriptor for non-text symbols")
Cc: stable@vger.kernel.org # v4.13+
Reported-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.
In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.
Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.
Fixes: 85926f877040 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide a mailing list for maintenance of the module instead.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the time being I will be available in my private mail. Update both the
MAINTAINERS file and the individual modules MODULE_AUTHOR directive with
the new address.
Signed-off-by: Yotam Gigi <yotam.gi@gmail.com>
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function of_parse_phandle() returns a NULL pointer if it cannot
resolve a phandle property to a device_node pointer. In function
hns_nic_dev_probe(), its return value is passed to PTR_ERR to extract
the error code. However, in this case, the extracted error code will
always be zero, which is unexpected.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function netdev_priv() returns the private data of the device. The
memory to store the private data is allocated in alloc_netdev() and is
released in netdev_free(). Calling kfree() on the return value of
netdev_priv() after netdev_free() results in a double free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that SK_REDIRECT is no longer a valid return code. Remove it
from the UAPI completely. Then do a namespace remapping internal
to sockmap so SK_REDIRECT is no longer externally visible.
Patchs primary change is to do a namechange from SK_REDIRECT to
__SK_REDIRECT
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fix 5987feb38aa5 ("net: phy: marvell: logical vs bitwise OR typo")
uncovered another bug in the Marvell PHY driver, which broke the
Marvell OpenRD platform. It relies on the bootloader configuring the
RGMII delays and does not specify a phy-mode in its device tree. The
PHY driver should only configure RGMII delays if the phy mode
indicates it is using RGMII. Without anything in device tree, the
mv643xx Ethernet driver defaults to GMII.
Fixes: 5987feb38aa5 ("net: phy: marvell: logical vs bitwise OR typo")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
The most important here is the security vulnerabitility fix for
ath10k.
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
single nouveau regression fix.
* 'linux-4.14' of git://github.com/skeggsb/linux:
drm/nouveau/kms/nv50: use the correct state for base channel notifier setup
|
|
Fixes: 857263 ("drm/nouveau: Handle drm_atomic_helper_swap_state failure")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Lyude Paul <lyude@redhat.com>
Reviewed by: Lyude Paul <lyude@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management commit reverts from Rafael Wysocki:
"Since Geert reports additional problems with my PM QoS fix from the
last week that have not been addressed by the most recent fixup on top
of it, they both should better be reverted now and let's fix the
original issue properly in 4.15.
This reverts two recent PM QoS commits one of which introduced
multiple problems and the other one fixed some, but not all of them
(Rafael Wysocki)"
* tag 'pm-reverts-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / QoS: Fix device resume latency PM QoS"
Revert "PM / QoS: Fix default runtime_pm device resume latency"
|
|
By default, sparse assumes a 64bit machine when compiled on x86-64
and 32bit when compiled on anything else.
This can of course create all sort of problems, like issuing false
warnings like: 'constant ... is so big it is unsigned long long'
or 'shift too big (32) for type unsigned long' when the architecture
is 64bit while sparse was compiled on a 32bit machine, or worse,
to not emit legitimate warnings in the reverse situation.
Fix this by passing to sparse the appropriate -m32/-m64 flag.
To: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
|
|
Change run_tests to print individual test results to console by default.
Introduce "summary" option to print individual test results to a file
/tmp/test_name and just print the summary to the console.
This change is necessary to support use-cases where test machines get
rebooted once tests are run and the console log should contain the full
results.
In the following example, individual test results with "summary=1" option
are written to /tmp/kcmp_test
make --silent TARGETS=kcmp kselftest
TAP version 13
selftests: kcmp_test
========================================
pid1: 30126 pid2: 30127 FD: 2 FILES: 2 VM: 1 FS: 2 SIGHAND: 2 IO:
0 SYSVSEM: 0 INV: -1
PASS: 0 returned as expected
PASS: 0 returned as expected
FAIL: 0 expected but -1 returned (Invalid argument)
Pass 2 Fail 1 Xfail 0 Xpass 0 Skip 0 Error 0
1..3
Bail out!
Pass 2 Fail 1 Xfail 0 Xpass 0 Skip 0 Error 0
1..3
Pass 0 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
1..0
ok 1..1 selftests: kcmp_test [PASS]
make --silent TARGETS=kcmp summary=1 kselftest
TAP version 13
selftests: kcmp_test
========================================
ok 1..1 selftests: kcmp_test [PASS]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
IB device index is nldev's handler and it should be checked always.
Fixes: c3f66f7b0052 ("RDMA/netlink: Implement nldev port doit callback")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Doug Ledford <dledford@redhat.com>
[ Applying directly, since Doug fried his SSD's and is rebuilding - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 0cc2b4e5a020 (PM / QoS: Fix device resume latency PM
QoS) as it introduced regressions on multiple systems and the fix-up
in commit 2a9a86d5c813 (PM / QoS: Fix default runtime_pm device resume
latency) does not address all of them.
The original problem that commit 0cc2b4e5a020 was attempting to fix
will be addressed later.
Fixes: 0cc2b4e5a020 (PM / QoS: Fix device resume latency PM QoS)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This reverts commit 2a9a86d5c813 (PM / QoS: Fix default runtime_pm
device resume latency) as the commit it depends on is going to be
reverted.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ath.git fixes for 4.14. Major changes:
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
|
|
On error, kthread_create() returns an errno-encoded pointer, not NULL.
The routine qla2x00_probe_one() detects the error case and jumps to
probe_failed, but has already assigned the return value from
kthread_create() to ha->dpc_thread. Then probe_failed checks to see if
ha->dpc_thread is not NULL before doing cleanup on it. Since in the
error case this is also not NULL, it ends up trying to access an invalid
task pointer.
Solution is to assign NULL to ha->dpc_thread in the error path to avoid
kthread cleanup in that case.
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We reset the encapsulation field of the skb too early
in xfrm_output. As a result, the GRE GSO handler does
not segment the packets. This leads to a performance
drop down. We fix this by resetting the encapsulation
field right before we do the transformation, when
the inner headers become invalid.
Fixes: f1bd7d659ef0 ("xfrm: Add encapsulation header offsets while SKB is not encrypted")
Reported-by: Vicente De Luca <vdeluca@zendesk.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
