| Age | Commit message (Collapse) | Author |
|---|
|
This patch puts a common part as the first field of mlx5_core_qp. This field is
used to identify which resource generated an event. This is required since upcoming
new resource types such as DC targets are allocated for the same numerical space
as regular QPs and may generate the same events. By searching the resource in the
same table we can then look at the common field to identify the resource.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Transform device capabilities related commands to use set/get macros to
manipulate command mailboxes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an auto generated header file that describes hardware registers along with
set of macros that set/get values. The macros do static checks to avoid
overflow, handle endianess, and overall provide a clean way to code commands.
Currently the header file is small and we will add structs as we make use of
the macros.
A few commands were removed from the commands enum since they are not supported
currently and will be added when support is available.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rearrange struct mlx5_caps so it has a "gen" field to represent the current
capabilities configured for the device. Max capabilities can also be queried
from the device. Also update capabilities struct to contain more fields as per
the latest revision if firmware specification.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Validation of skb can be pretty expensive :
GSO segmentation and/or checksum computations.
We can do this without holding qdisc lock, so that other cpus
can queue additional packets.
Trick is that requeued packets were already validated, so we carry
a boolean so that sch_direct_xmit() can validate a fresh skb list,
or directly use an old one.
Tested on 40Gb NIC (8 TX queues) and 200 concurrent flows, 48 threads
host.
Turning TSO on or off had no effect on throughput, only few more cpu
cycles. Lock contention on qdisc lock disappeared.
Same if disabling TX checksum offload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Follow commits c706471b2601 ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbfb36c ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jesper Dangaard Brouer says:
====================
qdisc: bulk dequeue support
This patchset uses DaveM's recent API changes to dev_hard_start_xmit(),
from the qdisc layer, to implement dequeue bulking.
Patch01: "qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE"
- Implement basic qdisc dequeue bulking
- This time, 100% relying on BQL limits, no magic safe-guard constants
Patch02: "qdisc: dequeue bulking also pickup GSO/TSO packets"
- Extend bulking to bulk several GSO/TSO packets
- Seperate patch, as it introduce a small regression, see test section.
We do have a patch03, which exports a userspace tunable as a BQL
tunable, that can byte-cap or disable the bulking/bursting. But we
could not agree on it internally, thus not sending it now. We
basically strive to avoid adding any new userspace tunable.
Testing patch01:
================
Demonstrating the performance improvement of qdisc dequeue bulking, is
tricky because the effect only "kicks-in" once the qdisc system have a
backlog. Thus, for a backlog to form, we need either 1) to exceed wirespeed
of the link or 2) exceed the capability of the device driver.
For practical use-cases, the measureable effect of this will be a
reduction in CPU usage
01-TCP_STREAM:
--------------
Testing effect for TCP involves disabling TSO and GSO, because TCP
already benefit from bulking, via TSO and especially for GSO segmented
packets. This patch view TSO/GSO as a seperate kind of bulking, and
avoid further bulking of these packet types.
The measured perf diff benefit (at 10Gbit/s) for a single netperf
TCP_STREAM were 9.24% less CPU used on calls to _raw_spin_lock()
(mostly from sch_direct_xmit).
If my E5-2695v2(ES) CPU is tuned according to:
http://netoptimizer.blogspot.dk/2014/04/basic-tuning-for-network-overload.html
Then it is possible that a single netperf TCP_STREAM, with GSO and TSO
disabled, can utilize all bandwidth on a 10Gbit/s link. This will
then cause a standing backlog queue at the qdisc layer.
Trying to pressure the system some more CPU util wise, I'm starting
24x TCP_STREAMs and monitoring the overall CPU utilization. This
confirms bulking saves CPU cycles when it "kicks-in".
Tool mpstat, while stressing the system with netperf 24x TCP_STREAM, shows:
* Disabled bulking: sys:2.58% soft:8.50% idle:88.78%
* Enabled bulking: sys:2.43% soft:7.66% idle:89.79%
02-UDP_STREAM
-------------
The measured perf diff benefit for UDP_STREAM were 6.41% less CPU used
on calls to _raw_spin_lock(). 24x UDP_STREAM with packet size -m 1472 (to
avoid sending UDP/IP fragments).
03-trafgen driver test
----------------------
The performance of the 10Gbit/s ixgbe driver is limited due to
updating the HW ring-queue tail-pointer on every packet. As
previously demonstrated with pktgen.
Using trafgen to send RAW frames from userspace (via AF_PACKET), and
forcing it through qdisc path (with option --qdisc-path and -t0),
sending with 12 CPUs.
I can demonstrate this driver layer limitation:
* 12.8 Mpps with no qdisc bulking
* 14.8 Mpps with qdisc bulking (full 10G-wirespeed)
Testing patch02:
================
Testing Bulking several GSO/TSO packets:
Measuring HoL (Head-of-Line) blocking for TSO and GSO, with
netperf-wrapper. Bulking several TSO show no performance regressions
(requeues were in the area 32 requeues/sec for 10G while transmitting
approx 813Kpps).
Bulking several GSOs does show small regression or very small
improvement (requeues were in the area 8000 requeues/sec, for 10G
while transmitting approx 813Kpps).
Using ixgbe 10Gbit/s with GSO bulking, we can measure some additional
latency. Base-case, which is "normal" GSO bulking, sees varying
high-prio queue delay between 0.38ms to 0.47ms. Bulking several GSOs
together, result in a stable high-prio queue delay of 0.50ms.
Corrosponding to:
(10000*10^6)*((0.50-0.47)/10^3)/8 = 37500 bytes
(10000*10^6)*((0.50-0.38)/10^3)/8 = 150000 bytes
37500/1500 = 25 pkts
150000/1500 = 100 pkts
Using igb at 100Mbit/s with GSO bulking, shows an improvement.
Base-case sees varying high-prio queue delay between 2.23ms to 2.35ms
diff of 0.12ms corrosponding to 1500 bytes at 100Mbit/s. Bulking
several GSOs together, result in a stable high-prio queue delay of
2.23ms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSO and GSO segmented packets already benefit from bulking
on their own.
The TSO packets have always taken advantage of the only updating
the tailptr once for a large packet.
The GSO segmented packets have recently taken advantage of
bulking xmit_more API, via merge commit 53fda7f7f9e8 ("Merge
branch 'xmit_list'"), specifically via commit 7f2e870f2a4 ("net:
Move main gso loop out of dev_hard_start_xmit() into helper.")
allowing qdisc requeue of remaining list. And via commit
ce93718fb7cd ("net: Don't keep around original SKB when we
software segment GSO frames.").
This patch allow further bulking of TSO/GSO packets together,
when dequeueing from the qdisc.
Testing:
Measuring HoL (Head-of-Line) blocking for TSO and GSO, with
netperf-wrapper. Bulking several TSO show no performance regressions
(requeues were in the area 32 requeues/sec).
Bulking several GSOs does show small regression or very small
improvement (requeues were in the area 8000 requeues/sec).
Using ixgbe 10Gbit/s with GSO bulking, we can measure some additional
latency. Base-case, which is "normal" GSO bulking, sees varying
high-prio queue delay between 0.38ms to 0.47ms. Bulking several GSOs
together, result in a stable high-prio queue delay of 0.50ms.
Using igb at 100Mbit/s with GSO bulking, shows an improvement.
Base-case sees varying high-prio queue delay between 2.23ms to 2.35ms
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on DaveM's recent API work on dev_hard_start_xmit(), that allows
sending/processing an entire skb list.
This patch implements qdisc bulk dequeue, by allowing multiple packets
to be dequeued in dequeue_skb().
The optimization principle for this is two fold, (1) to amortize
locking cost and (2) avoid expensive tailptr update for notifying HW.
(1) Several packets are dequeued while holding the qdisc root_lock,
amortizing locking cost over several packet. The dequeued SKB list is
processed under the TXQ lock in dev_hard_start_xmit(), thus also
amortizing the cost of the TXQ lock.
(2) Further more, dev_hard_start_xmit() will utilize the skb->xmit_more
API to delay HW tailptr update, which also reduces the cost per
packet.
One restriction of the new API is that every SKB must belong to the
same TXQ. This patch takes the easy way out, by restricting bulk
dequeue to qdisc's with the TCQ_F_ONETXQUEUE flag, that specifies the
qdisc only have attached a single TXQ.
Some detail about the flow; dev_hard_start_xmit() will process the skb
list, and transmit packets individually towards the driver (see
xmit_one()). In case the driver stops midway in the list, the
remaining skb list is returned by dev_hard_start_xmit(). In
sch_direct_xmit() this returned list is requeued by dev_requeue_skb().
To avoid overshooting the HW limits, which results in requeuing, the
patch limits the amount of bytes dequeued, based on the drivers BQL
limits. In-effect bulking will only happen for BQL enabled drivers.
Small amounts for extra HoL blocking (2x MTU/0.24ms) were
measured at 100Mbit/s, with bulking 8 packets, but the
oscillating nature of the measurement indicate something, like
sched latency might be causing this effect. More comparisons
show, that this oscillation goes away occationally. Thus, we
disregard this artifact completely and remove any "magic" bulking
limit.
For now, as a conservative approach, stop bulking when seeing TSO and
segmented GSO packets. They already benefit from bulking on their own.
A followup patch add this, to allow easier bisect-ability for finding
regressions.
Jointed work with Hannes, Daniel and Florian.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the ethernet driver for Agere et131x devices to
drivers/net/ethernet.
The driver being added has been in the staging tree for some time, and will be
removed from there in a seperate patch. This one merely disables the staging
version to prevent two instances being built.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have to register the notifiers in the masquerade expression from
the the module _init and _exit path.
This fixes crashes when removing the masquerade rule with no
ipt_MASQUERADE support in place (which was masking the problem).
Fixes: 9ba1f72 ("netfilter: nf_tables: add new nft_masq expression")
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Indenting errors yielded the following static checker warnings:
drivers/net/wireless/rtlwifi/rtl8192ee/hw.c:533 rtl92ee_set_hw_reg() warn: add curly braces? (if)
drivers/net/wireless/rtlwifi/rtl8192ee/hw.c:539 rtl92ee_set_hw_reg() warn: add curly braces? (if)
An unreleased version of the static checker also reported:
drivers/net/wireless/rtlwifi/rtl8723be/trx.c:550 rtl8723be_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:621 rtl88ee_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192ee/trx.c:567 rtl92ee_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8821ae/trx.c:758 rtl8821ae_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:494 rtl8723e_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:315 rtl92se_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:392 rtl92ce_rx_query_desc() warn: 'hdr' can't be NULL.
All of these are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The driver needs btcoexist, but Kconfig fails to select it. This omission
could cause build errors for some configurations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When we are attempting to switch to a new
channel context, the TX queues are flushed, but
the mac80211 queues are not stopped and traffic
can still come down to the driver.
This patch fixes it by stopping the queues
assigned to the current context/vif before
trying to flush.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When a full chip reset is done, all the queues
across all VIFs are stopped, but if MCC is enabled,
only the queues of the current context is awakened,
when we complete the reset.
This results in unfairness for the inactive context.
Since frames are queued internally in the driver if
there is a context mismatch, we can awaken all the
queues when coming out of a reset.
The VIF-specific queues are still used in flow control,
to ensure fairness when traffic is high.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This can be used when the queues of a context
needs to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Change the ath9k_chanctx_wake_queues() API so
that we can pass the channel context that needs its
queues to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When draining of the TX queues fails, a
full HW reset is done. ath_reset() makes sure
that the queues in mac80211 are restarted,
so there is no need to wake them up again.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_has_tx_pending() can be used to
check if there are pending frames instead
of having duplicate code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Checking for the queue depth outside of
the TX queue lock is incorrect and in this
case, is not required since it is done inside
ath9k_has_pending_frames().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is no need to check if the current
channel context has active ACs queued up
if the TX queue is not empty.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds SD8887 support to mwifiex.
SD8887 is Marvell's 1x1 11ac solution.
The corresponding firmware image file is located at:
"mrvl/sd8887_uapsta.bin"
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds some more defitions to card specific register structure
and removes static defines for these registers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Introduce netdev IOCTLs, to be used by the debug tools.
Allows to read/write single dword value or
memory block, aligned to dword
Different address modes supported:
- BAR offset
- Firmware "linker" address
- target's AHB bus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Introduce manual FW recovery mode. It is activated if module parameter
@no_fw_recovery set to true. May be changed at runtime.
Recovery information provided by new "recovery" debugfs file. It prints:
mode = [auto|manual]
state = [idle|pending|running]
In manual mode, after FW error, recovery won't start automatically. Instead,
after notification to user space, recovery waits in "pending" state, as indicated by the
"recovery" debugfs file. User space tools may perform data collection and allow to
continue recovery by writing "run" to the "recovery" debugfs file.
Alternatively, recovery pending may be canceled by stopping network interface
i.e. 'ifconfig wlan0 down'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
* Consistently use the multi-line comment style for networking code:
/* This
* That
* The other thing
*/
* Use single-line comment style for comments with only one line of text.
* In general follow the leading '*' of each line of a comment with a
single space and then text.
* Add missing line break between functions, remove double line break,
align comments to previous lines whenever possible.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
You can use physdev to match the physical interface enslaved to the
bridge device. This information is stored in skb->nf_bridge and it is
set up by br_netfilter. So, this is only available when iptables is
used from the bridge netfilter path.
Since 34666d4 ("netfilter: bridge: move br_netfilter out of the core"),
the br_netfilter code is modular. To reduce the impact of this change,
we can autoload the br_netfilter if the physdev match is used since
we assume that the users need br_netfilter in place.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This allows us to emulate the NAT table in ebtables, which is actually
a plain filter chain that hooks at prerouting, output and postrouting.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This code was based on the wrong asumption that you can probe based
on the match/target private size that we get from userspace. This
doesn't work at all when you have to dump the info back to userspace
since you don't know what word size the userspace utility is using.
Currently, the extensions that require arch compat are limit match
and the ebt_mark match/target. The standard targets are not used by
the nft-xt compat layer, so they are not affected. We can work around
this limitation with a new revision that uses arch agnostic types.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Make sure the objects have been released before the nf_tables modules
is removed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In 34666d4 ("netfilter: bridge: move br_netfilter out of the core"),
the bridge netfilter code has been modularized.
Use IS_ENABLED instead of ifdef to cover the module case.
Fixes: 34666d4 ("netfilter: bridge: move br_netfilter out of the core")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Move nf_send_reset() and nf_send_reset6() to nf_reject_ipv4 and
nf_reject_ipv6 respectively. This code is shared by x_tables and
nf_tables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch introduces the NFT_REJECT_ICMPX_UNREACH type which provides
an abstraction to the ICMP and ICMPv6 codes that you can use from the
inet and bridge tables, they are:
* NFT_REJECT_ICMPX_NO_ROUTE: no route to host - network unreachable
* NFT_REJECT_ICMPX_PORT_UNREACH: port unreachable
* NFT_REJECT_ICMPX_HOST_UNREACH: host unreachable
* NFT_REJECT_ICMPX_ADMIN_PROHIBITED: administratevely prohibited
You can still use the specific codes when restricting the rule to match
the corresponding layer 3 protocol.
I decided to not overload the existing NFT_REJECT_ICMP_UNREACH to have
different semantics depending on the table family and to allow the user
to specify ICMP family specific codes if they restrict it to the
corresponding family.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We did not return error if multicast packet transmit failed.
This might not be desired so return error also in this case.
If there are multiple 6lowpan devices where the multicast packet
is sent, then return error even if sending to only one of them fails.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Make sure that we are able to return EAGAIN from l2cap_chan_send()
even for multicast packets. The error code was ignored unncessarily.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
If skb_unshare() returns NULL, then we leak the original skb.
Solution is to use temp variable to hold the new skb.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The earlier multicast commit 36b3dd250dde ("Bluetooth: 6lowpan:
Ensure header compression does not corrupt IPv6 header") lost one
skb free which then caused memory leak.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Bump version
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Convert two more Intel NIC drivers to dev_consume_skb_any() to help
make dropped packet profiling sane.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove a source of latency spikes (in my case up to 10ms) by not calling
code that uses mdelay() for feeding a phy statistic (rx errors for idle
symbols - not data -> idle_errors) while being called with a spinlock held.
As idle_errors isn't read, this patch only removes unused code and data.
Later, more complicated changes may be applied to address the spinlock and
allow for some PHY diagnostics by harvesting this PHY stats register fully.
This patch is designed to fix the issue and be safe for longterm/stable.
For the Intel e1000e driver, the same change was applied in 2008 with
commit 23033fad5be0 ("e1000e: remove phy read from inside spinlock").
The mdelay is triggered by HW/SW semaphores, thus it depends on the HW.
I've HW that triggers it even when idle. Others may trigger it only e.g.
when Ethernet ports aquire or loose the link or on ifconfig up / down.
We've noticed this first from delays in frame rx/tx due to the mdelay().
Example command for checking if the issue is triggered: cyclictest -Smp1
(Look for occasional "Max:" values > 4000 or use -b 4000 to stop if greater)
It was observed with I350 ports connected to other I350 ports, but not
if driver and EEPROM was modified to run the I350 in EEPROM-less mode.
phy_stats.idle_errors and .receive_errors (isn't touched) occupy 64 not
used bits in the adapter struct: Their allocation may be removed as well.
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Fixes: 12dcd86b75d5 ("igb: fix stats handling") (this added the spin_lock)
Signed-off-by: Bernhard Kaindl <bk-linux@use.startmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is typo in ixgbe.h, two marcro definition of IXGBE_MAX_L2A_QUEUES to 4,
delete one, clear the compiler warning.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch consolidates the logic behind dynamically setting TXDCTL.WTHRESH
depending on interrupt throttle rate (ITR) setting regardless of BQL.
Previously TXDCTL.WTHRESH was dynamically being set only with BQL being
enabled, but we have to set it regardless of BQL when ITR is low to avoid
Tx stalls/hangs.
CC: John Greene <jogreene@redhat.com>
Reported by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes couple of wait loops on autoneg that are not needed.
During validation we noticed that the loops always time out, so there
should be no user impact.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Convert the normal packet completion path to dev_consume_skb_any() so
packet drop profiling via dropwatch or perf top -G -e skb_kfree_skb
is not cluttered with false hits.
Compile tested only. There is a dev_kfree_skb_any() in the routine
ixgbe_ptp_tx_hwtstamp() in ixgbe_ptp.c that looks like a conversion
candidate but I wasn't familiar enough with the code to pull the
trigger.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The L2CAP connection's channel list lock (conn->chan_lock) must never be
taken while already holding a channel lock (chan->lock) in order to
avoid lock-inversion and lockdep warnings. So far the l2cap_chan_connect
function has acquired the chan->lock early in the function and then
later called l2cap_chan_add(conn, chan) which will try to take the
conn->chan_lock. This violates the correct order of taking the locks and
may lead to the following type of lockdep warnings:
-> #1 (&conn->chan_lock){+.+...}:
[<c109324d>] lock_acquire+0x9d/0x140
[<c188459c>] mutex_lock_nested+0x6c/0x420
[<d0aab48e>] l2cap_chan_add+0x1e/0x40 [bluetooth]
[<d0aac618>] l2cap_chan_connect+0x348/0x8f0 [bluetooth]
[<d0cc9a91>] lowpan_control_write+0x221/0x2d0 [bluetooth_6lowpan]
-> #0 (&chan->lock){+.+.+.}:
[<c10928d8>] __lock_acquire+0x1a18/0x1d20
[<c109324d>] lock_acquire+0x9d/0x140
[<c188459c>] mutex_lock_nested+0x6c/0x420
[<d0ab05fd>] l2cap_connect_cfm+0x1dd/0x3f0 [bluetooth]
[<d0a909c4>] hci_le_meta_evt+0x11a4/0x1260 [bluetooth]
[<d0a910eb>] hci_event_packet+0x3ab/0x3120 [bluetooth]
[<d0a7cb08>] hci_rx_work+0x208/0x4a0 [bluetooth]
CPU0 CPU1
---- ----
lock(&conn->chan_lock);
lock(&chan->lock);
lock(&conn->chan_lock);
lock(&chan->lock);
Before calling l2cap_chan_add() the channel is not part of the
conn->chan_l list, and can therefore only be accessed by the L2CAP user
(such as l2cap_sock.c). We can therefore assume that it is the
responsibility of the user to handle mutual exclusion until this point
(which we can see is already true in l2cap_sock.c by it in many places
touching chan members without holding chan->lock).
Since the hci_conn and by exctension l2cap_conn creation in the
l2cap_chan_connect() function depend on chan details we cannot simply
add a mutex_lock(&conn->chan_lock) in the beginning of the function
(since the conn object doesn't yet exist there). What we can do however
is move the chan->lock taking later into the function where we already
have the conn object and can that way take conn->chan_lock first.
This patch implements the above strategy and does some other necessary
changes such as using __l2cap_chan_add() which assumes conn->chan_lock
is held, as well as adding a second needed label so the unlocking
happens as it should.
Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The number of Tx queues was not being updated due to some issues when
generating the patches. This change makes sure to add the lines necessary
to update the number of Tx queues correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
