| Age | Commit message (Collapse) | Author |
|---|
|
Add definition for egress router interface table. This table describes
the final part in the routing pipeline. This table matches the egress
interface index (rif index, which is set by the previous stages and
determine the out port) and makes the decision of forwarding the packet
towards the L2 logic or dropping it.
The metadata header is added to represent this internal information.
The rif index field is mapped logically to netdevice ifindex.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add placeholder for dpipe. Support for specific tables and headers will
be introduced in following patches. The headers are shared between all
mlxsw_sp instances.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update RITR for counter support. This allows adding counters for
ASIC's router ports.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pipeline debug is used to export the pipeline abstractions for the
main objects - tables, headers and entries. The only support for set is
for changing the counter parameter on specific table.
The basic structures:
Header - can represent a real protocol header information or internal
metadata. Generic protocol headers like IPv4 can be shared
between drivers. Each driver can add local headers.
Field - part of a header. Can represent protocol field or specific ASIC
metadata field. Hardware special metadata fields can be mapped
to different resources, for example switch ASIC ports can have
internal number which from the systems point of view is mapped
to netdeivce ifindex.
Match - represent specific match rule. Can describe match on specific
field or header. The header index should be specified as well
in order to support several header instances of the same type
(tunneling).
Action - represents specific action rule. Actions can describe operations
on specific field values for example like set, increment, etc.
And header operation like add and delete.
Value - represents value which can be associated with specific match or
action.
Table - represents a hardware block which can be described with match/
action behavior. The match/action can be done on the packets
data or on the internal metadata that it gathered along the
packets traversal throw the pipeline which is vendor specific
and should be exported in order to provide understanding of
ASICs behavior.
Entry - represents single record in a specific table. The entry is
identified by specific combination of values for match/action.
Prior to accessing the tables/entries the drivers provide the header/
field data base which is used by driver to user-space. The data base
is split between the shared headers and unique headers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This includes calling the parsing code that translates from pedit
speak to the HW API, allocation (deallocation) of a modify header
context and setting the modify header id associated with this
context to the FTE of that flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This includes calling the parsing code that translates from pedit
speak to the HW API, allocation (deallocation) of a modify header
context and setting the modify header id associated with this
context to the FTE of that flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Parse/translate a set of TC pedit actions to be formed in the HW API format.
User-space provides set of keys where each one of them is made of: command (add or
set), header-type, byte offset within that header along with a 32 bit mask and value.
The mask dictates what bits in the 32 bit word that starts on the offset we should
be dealing with, but under negative polarity (unset bits are to be modified).
We do a 1st pass over the set of keys while using the header-type and offset to
fill the masks and the values into a data-structure containting all the
supported network headers.
We then do a 2nd pass over the set of fields to re-write supported by the HW,
where for each such candidate field, we use the masks filled on the 1st pass to
realize if we should offloading re-write it.
In case offloading is required, we fill a HW descriptor with the following:
(1) the header field to modify
(2) the bit offset within the field from where to modify (set command only)
(3) the value to set/add
(4) the length in bits 1...32 to modify (set command only)
Note that it's possible for a given pedit mask to dictate modifying the
same header field multiple times or to modify multiple header fields.
Currently such combinations are not supported for offloading, hence, for set
commands, the offset within the field is always zero, and the length to modify
is the field size.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
HW drivers will use the header-type and command fields from the extended
keys, and some fields (e.g mask, val, offset) from the legacy keys.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Implement the low-level commands to support packet header re-write.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
definitions
Add the definitions related to creation/deletion of a modify header
context and the modify header steering action which are used for HW
packet header modify (re-write) as part of steering. Add as well the
modify header id into two intermediate structs and set it to the FTE.
Note that as the push/pop vlan steering actions are emulated by the
ewitch management code, we're not breaking any compatibility while
changing their values to make room for the modify header action which
is not emulated and whose value is part of the FW API. The new bit
values for the emulated actions are at the end of the possible range.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move the commands related to scheduling elements and vport qos to
a suitable location (according to the MLX5_CMD_OP enum values) in
the command string and internal error helpers.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There are bunch of places in the code where the intermediate struct
that keeps the elements related to flow actions is initialized with
the same default values. Put that into a small DECLARE type helper.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The code for adding tc fdb flows leaves things half set when it fails
in the middle. Currently we are not leaking things (e.g eswitch
vlan reference, encap reference and HW resources) since the main
code to add flower rules does a cleanup by calling mlx5e_tc_del_flow().
This cleanup further works just b/c we're checking there if the HW rule
for the flow we are attempting to delete is valid before touching it, and
since under the current possible combinations of supported actions it's okay
to go and blidnly deref or delete all the action related resources (encap, vlan).
Instead, do things properly, namely make sure that if add flow fails we
clean all what was allocated or referenced. Now, the flow delete code can
blindly deref/deallocate both the rule and the actions related resources and
when more action combinations are introduced (such as the upcoming header
re-write) we are fine with clear and robust code.
While here, align all of nic/fdb parse actions/add flow functions to get
mlx5e_tc_flow struct param and pick the attributes or whatever else needed
from there.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add intermediate structure to store attributes parsed from TC filter
matching/actions parts which are soon to be configured into the HW.
Currently put there the flow matching spec after being parsed. More
content to be added in down-stream patch.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add structure that contains the attributes related to offloaded
NIC flows. Currently it has the actions and flow tag.
While here, do xmas tree cleanup of the TC configure function.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add esw_ prefix to the flow attributes attached to offloaded e-switch
TC flows. This is a pre-step to add attributes to offloaded NIC TC flows.
Also, save one pointer space by using gcc's zero size array, this would
be beneficial for environments where 100Ks (or Ms) of flows are offloaded.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-failsafe 27-03-2017
This series provides a fail-safe mechanism to allow safely re-configuring
mlx5e netdevice and provides a resiliency against sporadic
configuration failures.
To enable this we do some refactoring and code reorganizing to allow
breaking the drivers open/close flows to stages:
open -> activate -> deactivate -> close.
In addition we need to allow creating fresh HW ring resources
(mlx5e_channels) with their own "new" set of parameters, while keeping
the current ones running and active until the new channels are
successfully created with the new configuration, and only then we can
safly replace (switch) old channels with new ones.
For that we introduce mlx5e_channels object and an API to manage it:
- channels = open_channels(new_params):
open fresh TX/RX channels
- activate_channels(channels):
redirect traffic to them and attach them to the netdev
- deactivate_channes(channels)
stop traffic and detach from netdev
- close(channels)
Free the TX/RX HW resources of those channels
With the above strategy it is straightforward to achieve the desired
behavior of fail-safe configuration. In pseudo code:
make_new_config(new_params)
{
old_channels = current_active_channels;
new_channels = create_channels(new_params);
if (!new_channels)
return "Failed, but current channels are still active :)"
deactivate_channels(old_channels); /* Can't fail */
set_hw_new_state(); /* If needed */
activate_channels(new_channels); /* Can't fail */
close_channels(old_channels);
current_active_channels = new_channels;
return "SUCCESS";
}
At the top of this series, we change the following flows to be fail-safe:
ethtool:
- ring parameters
- coalesce parameters
- tx copy break parameters
- cqe compressing/moderation mode setting (priv flags)
ndos:
- tc setup
- set features: LRO
- change mtu
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mahesh Bandewar says:
====================
link-status fixes for mii-monitoring
The mii monitoring is divided into two phases - inspect and commit. The
inspect phase technically should not make any changes to the state and
defer it to the commit phase. However detected link state inconsistencies
on several machines and discovered that it's the result of some
inconsistent update to link states and assumption that you *always* get
rtnl-mutex. In reality when trylock() fails to acquire rtnl-mutex, the
commit phase is postponed until next mii-mon run. At the next round
because of the state change performed in the previous inspect-run, this
round does not detect any changes and would skip calling commit phase.
This would result in an inconsistent state until next link event happens
(if it ever happens).
During the the commit phase, it's always assumed that speed and duplex
fetch is always successful, but that's always not the case. However the
slave state is marked UP irrespective of speed / duplex fetch operation.
If the speed / duplex fetch operation results in insane values for either
of these two fields, then keeping internal link state UP is not going to
provide fruitful results either.
Please see into individual patches for more details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bond_miimon_commit() marks the link UP after attempting to get the speed
and duplex settings for the link. There is a possibility that
bond_update_speed_duplex() could fail. This is another place where it
could result into an inconsistent bonding link state.
With this patch the link will be marked UP only if the speed and duplex
values retrieved have sane values and processed further.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bond_update_speed_duplex() retrieves speed and duplex settings. There
is a possibility of failure in retrieving these values but caller has
to assume it's always successful. This leads to having inconsistent
slave link settings. If these (speed, duplex) values cannot be
retrieved, then keeping the link UP causes problems.
The updated bond_update_speed_duplex() returns 0 on success if it
retrieves sane values for speed and duplex. On failure it returns 1
and marks the link down.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The primary issue is that mii-inspect phase updates link-state and
expects changes to be committed during the mii-commit phase. After
the inspect phase if it fails to acquire rtnl-mutex, the commit
phase (bond_mii_commit) doesn't get to run. This partially updated
state stays and makes the internal-state inconsistent.
e.g. setup bond0 => slaves: eth1, eth2
eth1 goes DOWN -> UP
mii_monitor()
mii-inspect()
bond_set_slave_link_state(eth1, UP, DontNotify)
rtnl_trylock() <- fails!
Next mii-monitor round
eth1: No change
mii_monitor()
mii-inspect()
eth1->link == current-status (ethtool_ops->get_link)
no-change-detected
End result:
eth1:
Link = BOND_LINK_UP
Speed = 0xfffff [SpeedUnknown]
Duplex = 0xff [DuplexUnknown]
This doesn't always happen but for some unlucky machines in a large set
of machines it creates problems.
The fix for this is to avoid making changes during inspect phase and
postpone them until acquiring the rtnl-mutex / invoking commit phase.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split the function into two (a) propose (b) commit phase without
changing the semantics for the original API.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-27
This series contains updates to i40e and i40evf only.
Alex updates the driver code so that we can do bulk updates of the page
reference count instead of just incrementing it by one reference at a
time. Fixed an issue where we were not resetting skb back to NULL when
we have freed it. Cleaned up the i40e_process_skb_fields() to align with
other Intel drivers. Removed FCoE code, since it is not supported in any
of the Fortville/Fortpark hardware, so there is not much point of carrying
the code around, especially if it is broken and untested.
Harshitha fixes a bug in the driver where the calculation of the RSS size
was not taking into account the number of traffic classes enabled.
Robert fixes a potential race condition during VF reset by eliminating
IOMMU DMAR Faults caused by VF hardware and when the OS initiates a VF
reset and before the reset is finished we modify the VF's settings.
Bimmy removes a delay that is no longer needed, since it was only needed
for preproduction hardware.
Colin King fixes null pointer dereference, where VSI was being
dereferenced before the VSI NULL check.
Jake fixes an issue with the recent addition of the "client code" to the
driver, where we attempt to use an uninitialized variable, so correctly
initialize the params variable by calling i40e_client_get_params().
v2: dropped patch 5 of the original series from Carolyn since we need
more documentation and reason why the added delay, so Carolyn is
taking the time to update the patch before we re-submit it for
kernel inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Probably due to some mis-merging fix a bug associated with commits
d7ce6422d6e6 ("i40e: don't check params until after checking for client
instance", 2017-02-09) and 3140aa9a78c9 ("i40e: KISS the client
interface", 2017-03-14)
The first commit tried to move the initialization of the params
structure so that we didn't bother doing this if we didn't have a client
interface. You can already see that it looks fishy because of the
indentation. The second commit refactors a bunch of the interface, and
incorrectly drops the params initialization.
I believe what occurred is that internally the two patches were
re-ordered, and the merge conflicts as a result were performed
incorrectly.
Fix the use of an uninitialized variable by correctly initializing the
params variable via i40e_client_get_params().
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
VSI is being dereferenced before the VSI null check; if VSI is
null we end up with a null pointer dereference. Fix this by
performing VSI deference after the VSI null check. Also remove
the need for using adapter by using vsi->back->cinst.
Detected by CoverityScan, CID#1419696, CID#1419697
("Dereference before null check")
Fixes: ed0e894de7c133 ("i40evf: add client interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since FCoE isn't supported by the i40e products there isn't much point in
carrying around code that will always evaluate to false. This patch goes
through and strips out the code in several spots so that we don't go around
carrying variables and/or code that is always going to evaluate to false or
0.
Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is a minor clean-up to make the i40e/i40evf process_skb_fields
function look a little more like what we have in igb. The Rx checksum
function called out a need for skb->protocol but I can't see where it
actually needs it. I am assuming this is something that was likely
refactored out some time ago as the Rx checksum code has gone through a few
rewrites.
Change-ID: I0b4668a34d90b61b66ded7c7c26e19a3e2d06251
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Removed no longer needed delays. At preproduction stage those delays were
needed but now these delays are not needed.
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
First, this patch eliminates IOMMU DMAR Faults caused by VF hardware.
This is done by enabling VF hardware only after VSI resources are
freed. Otherwise, hardware could DMA into memory that is (or just has
been) being freed.
Then, the VF driver is activated only after VSI resources have been
reallocated. That's because the VF driver can request resources
immediately after it's activated. So they need to be ready at that
point.
The second race condition happens when the OS initiates a VF reset,
and then before it's finished modifies VF's settings by changing its
MAC, VLAN ID, bandwidth allocation, anti-spoof checking, etc. These
functions needed to be blocked while VF is undergoing reset. Otherwise,
they could operate on data structures that had just been freed or not
yet fully initialized.
Change-ID: I43ba5a7ae2c9a1cce3911611ffc4598ae33ae3ff
Signed-off-by: Robert Konklewski <robertx.konklewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We need to reset skb back to NULL when we have freed it in the Rx cleanup
path. I found one spot where this wasn't occurring so this patch fixes it.
Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There exists a bug in the driver where the calculation of the
RSS size was not taking into account the number of traffic classes
enabled. This patch factors in the traffic classes both in
the initial configuration of the table as well as reconfiguration.
Change-ID: I34dcd345ce52faf1d6b9614bea28d450cfd5f621
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
I also found and fixed a store forwarding stall from where we were
assigning "*new_buff = *old_buff". By breaking it up into individual
copies we can avoid this and as a result the performance is slightly
improved.
Change-ID: I1d3880dece4133eca3c32423b04a5467321ccc52
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When CONFIG_IPV6_SEG6_LWTUNNEL is selected, automatically select DST_CACHE.
This allows to remove multiple ifdefs.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ibmvnic driver keeps its statistics in net_device->stats, so the
net_stats member in struct ibmvnic_adapter is unused. Remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ibmveth driver keeps its statistics in net_device->stats, so the
stats member in struct ibmveth_adapter is unused. Remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bfin_mac driver keeps its statistics in net_device->stats, so the
stats member in struct bfin_mac_local is unused. Remove it, as well as
the accompanying comment.
Cc: adi-buildroot-devel@lists.sourceforge.net
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ndev is being checked to see if it is a null pointer however before
the null check ndev is being dereferenced; hence there is a potential
null pointer dereference bug that needs fixing. Fix this by only
dereferencing ndev after the null check.
Detected by CoverityScan, CID#1420760, CID#140761 ("Dereference
before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Ahern says:
====================
net: mpls: multipath route cleanups
When a device associated with a nexthop is deleted, the nexthop in
the route is effectively removed, so remove it from the route dump.
Further, when all nexhops have been deleted the route is effectively
done, so remove the route.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When all devices for all nexthops in a route have been deleted, the
route is effectively dead, so remove it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the device for a nexthop in a multipath route is deleted, the nexthop
is effectively removed from the route. Currently, a route dump still
returns the nexhop though without the device set:
$ ip -f mpls ro ls
100
nexthopvia inet 10.11.1.2 dev br0
nexthopvia inet 10.100.3.1 dev eth3
$ ip li del br0
$ ip -f mpls ro ls
100
nexthopvia inet 10.11.1.2 dev * dead linkdown
nexthopvia inet 10.100.3.1 dev eth3
Since the nexthop is effectively deleted, drop the hop from the route
dump.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new fail-safe channels switch mechanism to set new
netdev mtu and lro settings.
MTU and lro settings demand some HW configuration changes after new
channels are created and ready for action. In order to unify switch
channels routine for LRO and MTU changes, and maybe future configuration
features, we now pass to it a modify HW function pointer to be
invoked directly after old channels are de-activated and before new
channels are activated.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Use the new fail-safe channels switch mechanism to set up new
tc parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Use the new fail-safe channels switch mechanism to set new
CQE compressing and CQE moderation mode settings.
We also move RX CQE compression modify function out of en_rx file to
a more appropriate place.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Use the new fail-safe channels switch mechanism to set new ethtool
settings:
- ring parameters
- coalesce parameters
- tx copy break parameters
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
A fail safe helper functions that allows switching to new channels on the
fly, In simple words:
make_new_config(new_params)
{
new_channels = open_channels(new_params);
if (!new_channels)
return "Failed, but current channels are still active :)"
switch_channels(new_channels);
return "SUCCESS";
}
Demonstrate mlx5e_switch_priv_channels usage in set channels ethtool
callback and make it fail-safe using the new switch channels mechanism.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
mlx5e_redirect_rqts_to_{channels,drop} and mlx5e_{add,del}_sqs_fwd_rules
and Set real num tx/rx queues belong to
mlx5e_{activate,deactivate}_priv_channels, for that we move those functions
and minimize mlx5e_open/close flows.
This will be needed in downstream patches to replace old channels with new
ones without the need to call mlx5e_close/open.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
