| Age | Commit message (Collapse) | Author |
|---|
|
ufshcd_tmc_handler() calls blk_mq_tagset_busy_iter(fn = ufshcd_compl_tm()),
but since blk_mq_tagset_busy_iter() only iterates over all reserved tags
and requests which are not in IDLE state, ufshcd_compl_tm() never gets a
chance to run. Thus, TMR always ends up with completion timeout. Fix it by
calling blk_mq_start_request() in __ufshcd_issue_tm_cmd().
Link: https://lore.kernel.org/r/1617262750-4864-2-git-send-email-cang@codeaurora.org
Fixes: 69a6c269c097 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Link: https://lore.kernel.org/r/20210330071958.3788214-3-slyfox@gentoo.org
Fixes: f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried cmds")
CC: linux-ia64@vger.kernel.org
CC: storagedev@microchip.com
CC: linux-scsi@vger.kernel.org
CC: Joe Szczypek <jszczype@redhat.com>
CC: Scott Benesh <scott.benesh@microchip.com>
CC: Scott Teel <scott.teel@microchip.com>
CC: Tomas Henzl <thenzl@redhat.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Don Brace <don.brace@microchip.com>
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Suggested-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Boot failure was observed on an HP rx3600 ia64 machine with RAID bus
controller: Hewlett-Packard Company Smart Array P600:
kernel unaligned access to 0xe000000105dd8b95, ip=0xa000000100b87551
kernel unaligned access to 0xe000000105dd8e95, ip=0xa000000100b87551
hpsa 0000:14:01.0: Controller reports max supported commands of 0 Using 16 instead. Ensure that firmware is up to date.
swapper/0[1]: error during unaligned kernel access
The unaligned access comes from 'struct CommandList' that happens to be
packed. Commit f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for
retried cmds") introduced unexpected padding and unaligned atomic_t from
natural alignment to something else.
This change removes packing annotation from a struct not intended to be
sent to controller as is. This restores natural `atomic_t` alignment.
The change was tested on the same rx3600 machine.
Link: https://lore.kernel.org/r/20210330071958.3788214-2-slyfox@gentoo.org
Fixes: f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried cmds")
CC: linux-ia64@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: storagedev@microchip.com
CC: linux-scsi@vger.kernel.org
CC: Joe Szczypek <jszczype@redhat.com>
CC: Scott Benesh <scott.benesh@microchip.com>
CC: Scott Teel <scott.teel@microchip.com>
CC: Tomas Henzl <thenzl@redhat.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Don Brace <don.brace@microchip.com>
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Suggested-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The hpsa driver uses data structures which contain a combination of driver
internals and commands sent directly to the hardware. To manage alignment
for the hardware portions the driver used #pragma pack(1).
Commit f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried
cmds") switched an existing variable from int to bool. Due to the pragma an
atomic_t in the same data structure ended up being misaligned and broke
boot on ia64.
Add __packed to every struct and union in the header file. Subsequent
commits will address the actual atomic_t misalignment regression.
The commit is a no-op at least on ia64:
$ diff -u <(objdump -d -r old.o) <(objdump -d -r new.o)
Link: https://lore.kernel.org/r/20210330071958.3788214-1-slyfox@gentoo.org
Fixes: f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried cmds")
CC: linux-ia64@vger.kernel.org
CC: storagedev@microchip.com
CC: linux-scsi@vger.kernel.org
CC: Joe Szczypek <jszczype@redhat.com>
CC: Scott Benesh <scott.benesh@microchip.com>
CC: Scott Teel <scott.teel@microchip.com>
CC: Tomas Henzl <thenzl@redhat.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Don Brace <don.brace@microchip.com>
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Suggested-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A kernel panic was observed due to a timing issue between the sync thread
and the initiator processing a login response from the target. The session
reopen can be invoked both from the session sync thread when iscsid
restarts and from iscsid through the error handler. Before the initiator
receives the response to a login, another reopen request can be sent from
the error handler/sync session. When the initial login response is
subsequently processed, the connection has been closed and the socket has
been released.
To fix this a new connection state, ISCSI_CONN_BOUND, is added:
- Set the connection state value to ISCSI_CONN_DOWN upon
iscsi_if_ep_disconnect() and iscsi_if_stop_conn()
- Set the connection state to the newly created value ISCSI_CONN_BOUND
after bind connection (transport->bind_conn())
- In iscsi_set_param(), return -ENOTCONN if the connection state is not
either ISCSI_CONN_BOUND or ISCSI_CONN_UP
Link: https://lore.kernel.org/r/20210325093248.284678-1-gulam.mohamed@oracle.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Gulam Mohamed <gulam.mohamed@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
index 91074fd97f64..f4bf62b007a0 100644
|
|
If pscsi_map_sg() fails, make sure to drop references to already allocated
bios.
Link: https://lore.kernel.org/r/20210323212431.15306-2-mwilck@suse.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
pscsi_map_sg() uses the variable nr_pages as a hint for bio_kmalloc() how
many vector elements to allocate. If nr_pages is < BIO_MAX_PAGES, it will
be reset to 0 after successful allocation of the bio.
If bio_add_pc_page() fails later for whatever reason, pscsi_map_sg() tries
to allocate another bio, passing nr_vecs = 0. This causes bio_add_pc_page()
to fail immediately in the next call. pci_map_sg() continues to allocate
zero-length bios until memory is exhausted and the kernel crashes with
OOM. This can be easily observed by exporting a SATA DVD drive via pscsi.
The target crashes as soon as the client tries to access the DVD LUN. In
the case I analyzed, bio_add_pc_page() would fail because the DVD device's
max_sectors_kb (128) was exceeded.
Avoid this by simply not resetting nr_pages to 0 after allocating the
bio. This way, the client receives an I/O error when it tries to send
requests exceeding the devices max_sectors_kb, and eventually gets it
right. The client must still limit max_sectors_kb e.g. by an udev rule if
(like in my case) the driver doesn't report valid block limits, otherwise
it encounters I/O errors.
Link: https://lore.kernel.org/r/20210323212431.15306-1-mwilck@suse.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When kzalloc() returns NULL, no error return code of mpt3sas_base_attach()
is assigned. To fix this bug, r is assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308035241.3288-1-baijiaju1990@gmail.com
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When kzalloc() returns NULL to qedi->global_queues[i], no error return code
of qedi_alloc_global_queues() is assigned. To fix this bug, status is
assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308033024.27147-1-baijiaju1990@gmail.com
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Calling vha->hw->tgt.tgt_ops->free_cmd() from qlt_xmit_response() is wrong
since the command for which a response is sent must remain valid until the
SCSI target core calls .release_cmd(). It has been observed that the
following scenario triggers a kernel crash:
- qlt_xmit_response() calls qlt_check_reserve_free_req()
- qlt_check_reserve_free_req() returns -EAGAIN
- qlt_xmit_response() calls vha->hw->tgt.tgt_ops->free_cmd(cmd)
- transport_handle_queue_full() tries to retransmit the response
Fix this crash by reverting the patch that introduced it.
Link: https://lore.kernel.org/r/20210320232359.941-2-bvanassche@acm.org
Fixes: 0dcec41acb85 ("scsi: qla2xxx: Make sure that aborted commands are freed")
Cc: Quinn Tran <qutran@marvell.com>
Cc: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During MQ enablement of the ibmvfc driver ibmvfc_wait_for_ops() was
missed. This function is responsible for waiting on commands to complete
that match a certain criteria such as LUN or cancel key. The implementation
as is only scans the CRQ for events ignoring any sub-queues and as a result
will exit successfully without doing anything when operating in MQ
channelized mode.
Check the MQ and channel use flags to determine which queues are
applicable, and scan each queue accordingly. Note in MQ mode SCSI commands
are only issued down sub-queues and the CRQ is only used for driver
specific management commands. As such the CRQ events are ignored when
operating in MQ mode with channels.
Link: https://lore.kernel.org/r/20210319205029.312969-3-tyreld@linux.ibm.com
Fixes: 9000cb998bcf ("scsi: ibmvfc: Enable MQ and set reasonable defaults")
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For various EH activities the ibmvfc driver uses ibmvfc_wait_for_ops() to
wait for the completion of commands that match a given criteria be it
cancel key, or specific LUN. With recent changes commands are completed
outside the lock in bulk by removing them from the sent list and adding
them to a private completion list. This introduces a potential race in
ibmvfc_wait_for_ops() since the criteria for a command to be outstanding is
no longer simply being on the sent list, but instead not being on the free
list.
Avoid this race by scanning the entire command event pool and checking that
any matching command that ibmvfc needs to wait on is not already on the
free list.
Link: https://lore.kernel.org/r/20210319205029.312969-2-tyreld@linux.ibm.com
Fixes: 1f4a4a19508d ("scsi: ibmvfc: Complete commands outside the host/queue lock")
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
mpt3sas_get_port_by_id() can be called when a spinlock is held. Use
GFP_ATOMIC instead of GFP_KERNEL when allocating memory.
Issue spotted by call_kern.cocci:
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7125 inside lock on line 7123 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6842 inside lock on line 6839 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6854 inside lock on line 6851 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7706 inside lock on line 7702 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 10260 inside lock on line 10256 but uses GFP_KERNEL
Link: https://lore.kernel.org/r/20210220093951.905362-1-christophe.jaillet@wanadoo.fr
Fixes: 324c122fc0a4 ("scsi: mpt3sas: Add module parameter multipath_on_hba")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The "lpm" and "->enabled" are all boolean. We should be using &&
rather than the bit operator.
Link: https://lore.kernel.org/r/1615896915-148864-1-git-send-email-dj0227@163.com
Fixes: 488edafb1120 ("scsi: ufs-mediatek: Introduce low-power mode for device power supply")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: dongjian <dongjian@yulong.com>
Signed-off-by: Yue Hu <huyue2@yulong.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Recent changes changed the completion of SCSI commands from Soft-IRQ
context to IRQ context. This triggers the following warning, when we're
completing writes to zoned block devices that go through the zone append
emulation:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc2+ #2
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0 12/17/2015
RIP: 0010:__local_bh_disable_ip+0x3f/0x50
RSP: 0018:ffff8883e1409ba8 EFLAGS: 00010006
RAX: 0000000080010001 RBX: 0000000000000001 RCX: 0000000000000013
RDX: ffff888129e4d200 RSI: 0000000000000201 RDI: ffffffff915b9dbd
RBP: ffff888113e9a540 R08: ffff888113e9a540 R09: 00000000000077f0
R10: 0000000000080000 R11: 0000000000000001 R12: ffff888129e4d200
R13: 0000000000001000 R14: 00000000000077f0 R15: ffff888129e4d218
FS: 0000000000000000(0000) GS:ffff8883e1400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2f8418ebc0 CR3: 000000021202a006 CR4: 00000000001706f0
Call Trace:
<IRQ>
_raw_spin_lock_bh+0x18/0x40
sd_zbc_complete+0x43d/0x1150
sd_done+0x631/0x1040
? mark_lock+0xe4/0x2fd0
? provisioning_mode_store+0x3f0/0x3f0
scsi_finish_command+0x31b/0x5c0
_scsih_io_done+0x960/0x29e0 [mpt3sas]
? mpt3sas_scsih_scsi_lookup_get+0x1c7/0x340 [mpt3sas]
? __lock_acquire+0x166b/0x58b0
? _get_st_from_smid+0x4a/0x80 [mpt3sas]
_base_process_reply_queue+0x23f/0x26e0 [mpt3sas]
? lock_is_held_type+0x98/0x110
? find_held_lock+0x2c/0x110
? mpt3sas_base_sync_reply_irqs+0x360/0x360 [mpt3sas]
_base_interrupt+0x8d/0xd0 [mpt3sas]
? rcu_read_lock_sched_held+0x3f/0x70
__handle_irq_event_percpu+0x24d/0x600
handle_irq_event+0xef/0x240
? handle_irq_event_percpu+0x110/0x110
handle_edge_irq+0x1f6/0xb60
__common_interrupt+0x75/0x160
common_interrupt+0x7b/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
Don't use spin_lock_bh() to protect the update of the write pointer offset
cache, but use spin_lock_irqsave() for it.
Link: https://lore.kernel.org/r/3cfebe48d09db73041b7849be71ffbcec7ee40b3.1615369586.git.johannes.thumshirn@wdc.com
Fixes: 664f0dce2058 ("scsi: mpt3sas: Add support for shared host tagset for CPU hotplug")
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If copy_from_user() or kstrtoull() fail then the correct behavior is to
return a negative error code.
Link: https://lore.kernel.org/r/YEsbU/UxYypVrC7/@mwanda
Fixes: f9bb2da11db8 ("[SCSI] lpfc 8.3.27: T10 additions for SLI4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Only half of the file is under include guard because terminating #endif
is placed too early.
Link: https://lore.kernel.org/r/YE4snvoW1SuwcXAn@localhost.localdomain
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In st_open(), if STp->in_use is true, STp will be freed by
scsi_tape_put(). However, STp is still used by DEBC_printk() after. It is
better to DEBC_printk() before scsi_tape_put().
Link: https://lore.kernel.org/r/20210311064636.10522-1-lyl2019@mail.ustc.edu.cn
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In myrs_cleanup(), cs->mmio_base will be freed twice by iounmap().
Link: https://lore.kernel.org/r/20210311063005.9963-1-lyl2019@mail.ustc.edu.cn
Fixes: 77266186397c ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The buffer for negotiating channel setup is DMA allocated at device probe
time. However, the remove path fails to free this allocation which will
prevent the hypervisor from releasing the virtual device in the case of a
hotplug remove.
Fix this issue by freeing the buffer allocation in ibmvfc_free_mem().
Link: https://lore.kernel.org/r/20210311012212.428068-1-tyreld@linux.ibm.com
Fixes: e95eef3fc0bc ("scsi: ibmvfc: Implement channel enquiry and setup commands")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The entries in the source files are removed as well.
Link: https://lore.kernel.org/r/20210226234347.21535-1-vbhakta@vmware.com
Signed-off-by: Vishal Bhakta <vbhakta@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix the following coccicheck warning:
./drivers/scsi/ufs/ufshcd.c:1538:8-16: WARNING: use scnprintf or
sprintf.
Link: https://lore.kernel.org/r/1614665298-115183-1-git-send-email-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Runtime and system suspend/resume can only come after hba probe invokes
platform_set_drvdata(pdev, hba), meaning hba cannot be NULL in these PM
callbacks, so remove the checks of !hba.
Link: https://lore.kernel.org/r/1614145010-36079-4-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Disable interrupt in reset path to flush pending IRQ handler in order to
avoid possible NoC issues.
Link: https://lore.kernel.org/r/1614145010-36079-3-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Nitin Rawat <nitirawa@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In error handling prepare stage, after SCSI requests are blocked, do a
down/up_write(clk_scaling_lock) to clean up the queuecommand() path.
Meanwhile, stop eeh_work in case it disturbs error recovery. Moreover,
reset ufshcd_state at the entrance of ufshcd_probe_hba(), since it may be
called multiple times during error recovery.
Link: https://lore.kernel.org/r/1614145010-36079-2-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A live partition migration (LPM) results in a CRQ disconnect similar to a
hard reset. In this LPM case the hypervisor mostly preserves the CRQ
transport such that it simply needs to be reenabled. However, the
capabilities may have changed such as fewer channels, or no channels at
all. Further, its possible that there may be sub-CRQ support, but no
channel support. The CRQ reenable path currently doesn't take any of this
into consideration.
For simplicity release and reinitialize sub-CRQs during reenable, and set
do_enquiry and using_channels with the appropriate values to trigger
channel renegotiation.
Link: https://lore.kernel.org/r/20210302230543.9905-6-tyreld@linux.ibm.com
Fixes: 3034ebe26389 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The H_FREE_SUB_CRQ hypercall can return a retry delay return code that
indicates the call needs to be retried after a specific amount of time
delay. The error path to free a sub-CRQ in case of a failure during channel
registration fails to capture the return code of H_FREE_SUB_CRQ which will
result in the delay loop being skipped in the case of a retry delay return
code.
Store the return code result of the H_FREE_SUB_CRQ call such that the
return code check in the delay loop evaluates a meaningful value. Also, use
the rtas_busy_delay() to check the rc value and delay for the appropriate
amount of time.
Link: https://lore.kernel.org/r/20210302230543.9905-5-tyreld@linux.ibm.com
Fixes: 39e461fddff0 ("scsi: ibmvfc: Map/request irq and register Sub-CRQ interrupt handler")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A non-zero return code for H_REG_SUB_CRQ is currently treated as a failure
resulting in failing sub-CRQ setup. The case of H_CLOSED should not be
treated as a failure. This return code translates to a successful sub-CRQ
registration by the hypervisor, and is meant to communicate back that there
is currently no partner VIOS CRQ connection established as of yet. This is
a common occurrence during a disconnect where the client adapter can
possibly come back up prior to the partner adapter.
For non-zero return code from H_REG_SUB_CRQ treat a H_CLOSED as success so
that sub-CRQs are successfully setup.
Link: https://lore.kernel.org/r/20210302230543.9905-4-tyreld@linux.ibm.com
Fixes: 3034ebe26389 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A hard reset results in a complete transport disconnect such that the CRQ
connection with the partner VIOS is broken. This has the side effect of
also invalidating the associated sub-CRQs. The current code assumes that
the sub-CRQs are perserved resulting in a protocol violation after trying
to reconnect them with the VIOS. This introduces an infinite loop such that
the VIOS forces a disconnect after each subsequent attempt to re-register
with invalid handles.
Avoid the aforementioned issue by releasing the sub-CRQs prior to CRQ
disconnect, and driving a reinitialization of the sub-CRQs once a new CRQ
is registered with the hypervisor.
Link: https://lore.kernel.org/r/20210302230543.9905-3-tyreld@linux.ibm.com
Fixes: 3034ebe26389 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If ibmvfc_init_sub_crqs() fails ibmvfc_probe() simply parrots registration
failure reported elsewhere, and futher vhost->scsi_scrq.scrq == NULL is
indication enough to the driver that it has no sub-CRQs available. The
mq_enabled check can also be moved into ibmvfc_init_sub_crqs() such that
each caller doesn't have to gate the call with a mq_enabled check. Finally,
in the case of sub-CRQ setup failure setting do_enquiry can be turned off
to putting the driver into single queue fallback mode.
The aforementioned changes also simplify the next patch in the series that
fixes a hard reset issue, by tying a sub-CRQ setup failure and do_enquiry
logic into ibmvfc_init_sub_crqs().
Link: https://lore.kernel.org/r/20210302230543.9905-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull misc fixes from Jens Axboe:
"Two misc fixes that don't belong in other branches:
- Fix a regression with ia64 signals, introduced by the
TIF_NOTIFY_SIGNAL change in 5.11.
- Fix the current swapfile regression from this merge window"
* tag 'misc-5.12-2021-03-02' of git://git.kernel.dk/linux-block:
swap: fix swapfile read/write offset
ia64: don't call handle_signal() unless there's actually a signal queued
|
|
We're not factoring in the start of the file for where to write and
read the swapfile, which leads to very unfortunate side effects of
writing where we should not be...
Fixes: 48d15436fde6 ("mm: remove get_swap_bio")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Sergei and John both reported that ia64 failed to boot in 5.11, and it
was related to signals. Turns out the ia64 signal handling is a bit odd,
it doesn't check the return value of get_signal() for whether there's a
signal to deliver or not. With the introduction of TIF_NOTIFY_SIGNAL,
then task_work could trigger it.
Fix it by only calling handle_signal() if we actually have a real signal
to deliver. This brings it in line with all other archs, too.
Fixes: b269c229b0e8 ("ia64: add support for TIF_NOTIFY_SIGNAL")
Reported-by: Sergei Trofimovich <slyich@gmail.com>
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull kmap conversion updates from David Sterba:
"This contains changes regarding kmap API use and eg conversion from
kmap_atomic to kmap_local_page.
The API belongs to memory management but to save cross-tree
dependency headaches we've agreed to take it through the btrfs tree
because there are some trivial conversions possible, while the rest
will need some time and getting the easy cases out of the way would be
convenient.
The changes can be grouped:
- function exports, new helpers
- new VM_BUG_ON for additional verification; it's been discussed if
it should be VM_BUG_ON or BUG_ON, the former was chosen due to
performance reasons
- code replaced by relevant helpers"
[ This is an updated version of a request that originally came in during
the merge window, but I asked for some updates:
https://lore.kernel.org/lkml/cover.1614090658.git.dsterba@suse.com/
which is why this got merge after the merge window closed. - Linus ]
* 'kmap-conversion-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: use copy_highpage() instead of 2 kmaps()
btrfs: use memcpy_[to|from]_page() and kmap_local_page()
mm/highmem: Add VM_BUG_ON() to mem*_page() calls
mm/highmem: Introduce memcpy_page(), memmove_page(), and memset_page()
mm/highmem: Convert memcpy_[to|from]_page() to kmap_local_page()
mm/highmem: Lift memcpy_[to|from]_page to core
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"This is the first batch of fixes that usually arrive during the merge
window code freeze. Regressions and stable material.
Regressions:
- fix deadlock in log sync in zoned mode
- fix bugs in subpage mode still wrongly assuming sectorsize == page
size
Fixes:
- fix missing kunmap of the Q stripe in RAID6
- block group fixes:
- fix race between extent freeing/allocation when using bitmaps
- avoid double put of block group when emptying cluster
- swapfile fixes:
- fix swapfile writes vs running scrub
- fix swapfile activation vs snapshot creation
- fix stale data exposure after cloning a hole with NO_HOLES enabled
- remove tree-checker check that does not work in case information
from other leaves is necessary"
* tag 'for-5.12-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix deadlock on log sync
btrfs: avoid double put of block group when emptying cluster
btrfs: fix stale data exposure after cloning a hole with NO_HOLES enabled
btrfs: tree-checker: do not error out if extent ref hash doesn't match
btrfs: fix race between swap file activation and snapshot creation
btrfs: fix race between writes to swap files and scrub
btrfs: avoid checking for RO block group twice during nocow writeback
btrfs: fix race between extent freeing/allocation when using bitmaps
btrfs: make check_compressed_csum() to be subpage compatible
btrfs: make btrfs_submit_compressed_read() subpage compatible
btrfs: fix raid6 qstripe kmap
|
|
|
|
Pull ide fix from Jens Axboe:
"This is a leftover fix from 5.11, where I forgot to ship it your way"
* tag 'ide-5.11-2021-02-28' of git://git.kernel.dk/linux-block:
ide/falconide: Fix module unload
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix UNUSED_KSYMS_WHITELIST for Clang LTO
- Make -s builds really silent irrespective of V= option
- Fix build error when SUBLEVEL or PATCHLEVEL is empty
* tag 'kbuild-fixes-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Fix <linux/version.h> for empty SUBLEVEL or PATCHLEVEL again
kbuild: make -s option take precedence over V=1
ia64: remove redundant READELF from arch/ia64/Makefile
kbuild: do not include include/config/auto.conf from adjust_autoksyms.sh
kbuild: fix UNUSED_KSYMS_WHITELIST for Clang LTO
kbuild: lto: add _mcount to list of used symbols
|
|
Pull arch/csky updates from Guo Ren:
"Features:
- add new memory layout 2.5G(user):1.5G(kernel)
- add kmemleak support
- reconstruct VDSO framework: add VDSO with GENERIC_GETTIMEOFDAY,
GENERIC_TIME_VSYSCALL, HAVE_GENERIC_VDSO
- add faulthandler_disabled() check
- support (fix) swapon
- add (fix) _PAGE_ACCESSED for default pgprot
- abort uaccess retries upon fatal signal (from arm)
Fixes and optimizations:
- fix perf probe failure
- fix show_regs doesn't contain regs->usp
- remove custom asm/atomic.h implementation
- fix barrier design
- fix futex SMP implementation
- fix asm/cmpxchg.h with correct ordering barrier
- cleanup asm/spinlock.h
- fix PTE global for 2.5:1.5 virtual memory
- remove prologue of page fault handler in entry.S
- fix TLB maintenance synchronization problem
- add show_tlb for CPU_CK860 debug
- fix FAULT_FLAG_XXX param for handle_mm_fault
- fix update_mmu_cache called with user io mapping
- fix do_page_fault parent irq status
- fix a size determination in gpr_get()
- pgtable.h: Coding convention
- kprobe: Fix code in simulate without 'long'
- fix pfn_valid error with wrong max_mapnr
- use free_initmem_default() in free_initmem()
- fix compile error"
* tag 'csky-for-linus-5.12-rc1' of git://github.com/c-sky/csky-linux: (30 commits)
csky: Fixup compile error
csky: use free_initmem_default() in free_initmem()
csky: Fixup pfn_valid error with wrong max_mapnr
csky: Add VDSO with GENERIC_GETTIMEOFDAY, GENERIC_TIME_VSYSCALL, HAVE_GENERIC_VDSO
csky: kprobe: Fixup code in simulate without 'long'
csky: Fixup swapon
csky: pgtable.h: Coding convention
csky: Fixup _PAGE_ACCESSED for default pgprot
csky: remove unused including <linux/version.h>
csky: Fix a size determination in gpr_get()
csky: Reconstruct VDSO framework
csky: mm: abort uaccess retries upon fatal signal
csky: Sync riscv mm/fault.c for easy maintenance
csky: Fixup do_page_fault parent irq status
csky: Add faulthandler_disabled() check
csky: Fixup update_mmu_cache called with user io mapping
csky: Fixup FAULT_FLAG_XXX param for handle_mm_fault
csky: Add show_tlb for CPU_CK860 debug
csky: Fix TLB maintenance synchronization problem
csky: Add kmemleak support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
"A pair of patches that slipped through the cracks:
- enable CPU hotplug in the defconfigs
- some cleanups to setup_bootmem
There's also a single fix for some randconfig build failures:
- make NUMA depend on SMP"
* tag 'riscv-for-linus-5.12-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Cleanup setup_bootmem()
RISC-V: Enable CPU Hotplug in defconfigs
RISC-V: Make NUMA depend on SMP
|
|
Pull more SCSI updates from James Bottomley:
"This is a few driver updates (iscsi, mpt3sas) that were still in the
staging queue when the merge window opened (all committed on or before
8 Feb) and some small bug fixes which came in during the merge window
(all committed on 22 Feb)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: hpsa: Correct dev cmds outstanding for retried cmds
scsi: sd: Fix Opal support
scsi: target: tcmu: Fix memory leak caused by wrong uio usage
scsi: target: tcmu: Move some functions without code change
scsi: sd: sd_zbc: Don't pass GFP_NOIO to kvcalloc
scsi: aic7xxx: Remove unused function pointer typedef ahc_bus_suspend/resume_t
scsi: bnx2fc: Fix Kconfig warning & CNIC build errors
scsi: ufs: Fix a duplicate dev quirk number
scsi: aic79xx: Fix spelling of version
scsi: target: core: Prevent underflow for service actions
scsi: target: core: Add cmd length set before cmd complete
scsi: iscsi: Drop session lock in iscsi_session_chkready()
scsi: qla4xxx: Use iscsi_is_session_online()
scsi: libiscsi: Reset max/exp cmdsn during recovery
scsi: iscsi_tcp: Fix shost can_queue initialization
scsi: libiscsi: Add helper to calculate max SCSI cmds per session
scsi: libiscsi: Fix iSCSI host workq destruction
scsi: libiscsi: Fix iscsi_task use after free()
scsi: libiscsi: Drop taskqueuelock
scsi: libiscsi: Fix iscsi_prep_scsi_cmd_pdu() error handling
...
|
|
Pull more xfs updates from Darrick Wong:
"The most notable fix here prevents premature reuse of freed metadata
blocks, and adding the ability to detect accidental nested
transactions, which are not allowed here.
- Restore a disused sysctl control knob that was inadvertently
dropped during the merge window to avoid fstests regressions.
- Don't speculatively release freed blocks from the busy list until
we're actually allocating them, which fixes a rare log recovery
regression.
- Don't nest transactions when scanning for free space.
- Add an idiot^Wmaintainer light to detect nested transactions. ;)"
* tag 'xfs-5.12-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: use current->journal_info for detecting transaction recursion
xfs: don't nest transactions when scanning for eofblocks
xfs: don't reuse busy extents on extent trim
xfs: restore speculative_cow_prealloc_lifetime sysctl
|
|
Pull more block updates from Jens Axboe:
"A few stragglers (and one due to me missing it originally), and fixes
for changes in this merge window mostly. In particular:
- blktrace cleanups (Chaitanya, Greg)
- Kill dead blk_pm_* functions (Bart)
- Fixes for the bio alloc changes (Christoph)
- Fix for the partition changes (Christoph, Ming)
- Fix for turning off iopoll with polled IO inflight (Jeffle)
- nbd disconnect fix (Josef)
- loop fsync error fix (Mauricio)
- kyber update depth fix (Yang)
- max_sectors alignment fix (Mikulas)
- Add bio_max_segs helper (Matthew)"
* tag 'block-5.12-2021-02-27' of git://git.kernel.dk/linux-block: (21 commits)
block: Add bio_max_segs
blktrace: fix documentation for blk_fill_rw()
block: memory allocations in bounce_clone_bio must not fail
block: remove the gfp_mask argument to bounce_clone_bio
block: fix bounce_clone_bio for passthrough bios
block-crypto-fallback: use a bio_set for splitting bios
block: fix logging on capacity change
blk-settings: align max_sectors on "logical_block_size" boundary
block: reopen the device in blkdev_reread_part
block: don't skip empty device in in disk_uevent
blktrace: remove debugfs file dentries from struct blk_trace
nbd: handle device refs for DESTROY_ON_DISCONNECT properly
kyber: introduce kyber_depth_updated()
loop: fix I/O error on fsync() in detached loop devices
block: fix potential IO hang when turning off io_poll
block: get rid of the trace rq insert wrapper
blktrace: fix blk_rq_merge documentation
blktrace: fix blk_rq_issue documentation
blktrace: add blk_fill_rwbs documentation comment
block: remove superfluous param in blk_fill_rwbs()
...
|
|
Commit 78d3bb4483ba ("kbuild: Fix <linux/version.h> for empty SUBLEVEL
or PATCHLEVEL") fixed the build error for empty SUBLEVEL or PATCHLEVEL
by prepending a zero.
Commit 9b82f13e7ef3 ("kbuild: clamp SUBLEVEL to 255") re-introduced
this issue.
This time, we cannot take the same approach because we have C code:
#define LINUX_VERSION_PATCHLEVEL $(PATCHLEVEL)
#define LINUX_VERSION_SUBLEVEL $(SUBLEVEL)
Replace empty SUBLEVEL/PATCHLEVEL with a zero.
Fixes: 9b82f13e7ef3 ("kbuild: clamp SUBLEVEL to 255")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-and-tested-by: Sasha Levin <sashal@kernel.org>
|
|
'make -s' should be really silent. However, 'make -s V=1' prints noisy
log messages from some shell scripts.
Of course, such a combination is odd, but the build system needs to do
the right thing even if a user gives strange input.
If -s is given, KBUILD_VERBOSE should be forced to 0.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
READELF is defined by the top Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Commit cd195bc4775a ("kbuild: split adjust_autoksyms.sh in two parts")
split out the code that needs include/config/auto.conf.
This script no longer needs to include include/config/auto.conf.
Fixes: cd195bc4775a ("kbuild: split adjust_autoksyms.sh in two parts")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Commit fbe078d397b4 ("kbuild: lto: add a default list of used symbols")
does not work as expected if the .config file has already specified
CONFIG_UNUSED_KSYMS_WHITELIST="my/own/white/list" before enabling
CONFIG_LTO_CLANG.
So, the user-supplied whitelist and LTO-specific white list must be
independent of each other.
I refactored the shell script so CONFIG_MODVERSIONS and CONFIG_CLANG_LTO
handle whitelists in the same way.
Fixes: fbe078d397b4 ("kbuild: lto: add a default list of used symbols")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
|
|
Pull io_uring thread rewrite from Jens Axboe:
"This converts the io-wq workers to be forked off the tasks in question
instead of being kernel threads that assume various bits of the
original task identity.
This kills > 400 lines of code from io_uring/io-wq, and it's the worst
part of the code. We've had several bugs in this area, and the worry
is always that we could be missing some pieces for file types doing
unusual things (recent /dev/tty example comes to mind, userfaultfd
reads installing file descriptors is another fun one... - both of
which need special handling, and I bet it's not the last weird oddity
we'll find).
With these identical workers, we can have full confidence that we're
never missing anything. That, in itself, is a huge win. Outside of
that, it's also more efficient since we're not wasting space and code
on tracking state, or switching between different states.
I'm sure we're going to find little things to patch up after this
series, but testing has been pretty thorough, from the usual
regression suite to production. Any issue that may crop up should be
manageable.
There's also a nice series of further reductions we can do on top of
this, but I wanted to get the meat of it out sooner rather than later.
The general worry here isn't that it's fundamentally broken. Most of
the little issues we've found over the last week have been related to
just changes in how thread startup/exit is done, since that's the main
difference between using kthreads and these kinds of threads. In fact,
if all goes according to plan, I want to get this into the 5.10 and
5.11 stable branches as well.
That said, the changes outside of io_uring/io-wq are:
- arch setup, simple one-liner to each arch copy_thread()
implementation.
- Removal of net and proc restrictions for io_uring, they are no
longer needed or useful"
* tag 'io_uring-worker.v3-2021-02-25' of git://git.kernel.dk/linux-block: (30 commits)
io-wq: remove now unused IO_WQ_BIT_ERROR
io_uring: fix SQPOLL thread handling over exec
io-wq: improve manager/worker handling over exec
io_uring: ensure SQPOLL startup is triggered before error shutdown
io-wq: make buffered file write hashed work map per-ctx
io-wq: fix race around io_worker grabbing
io-wq: fix races around manager/worker creation and task exit
io_uring: ensure io-wq context is always destroyed for tasks
arch: ensure parisc/powerpc handle PF_IO_WORKER in copy_thread()
io_uring: cleanup ->user usage
io-wq: remove nr_process accounting
io_uring: flag new native workers with IORING_FEAT_NATIVE_WORKERS
net: remove cmsg restriction from io_uring based send/recvmsg calls
Revert "proc: don't allow async path resolution of /proc/self components"
Revert "proc: don't allow async path resolution of /proc/thread-self components"
io_uring: move SQPOLL thread io-wq forked worker
io-wq: make io_wq_fork_thread() available to other users
io-wq: only remove worker from free_list, if it was there
io_uring: remove io_identity
io_uring: remove any grabbing of context
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted stuff pile - no common topic here"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
whack-a-mole: don't open-code iminor/imajor
9p: fix misuse of sscanf() in v9fs_stat2inode()
audit_alloc_mark(): don't open-code ERR_CAST()
fs/inode.c: make inode_init_always() initialize i_ino to 0
vfs: don't unnecessarily clone write access for writable fds
|
